Philips SBCRU240/38, SBCRU240/00 User Manual [pt]



UNIVERSAL



SBC RU 240

Instructions for use

Instrucciones de manejo

Manual de utilização

Code list

Universal Remote Control

You just made a great choice by buying this Philips universal remote control! It takes the place of as many as four separate remote controls and can operate the most-used functions of almost any brand of TV, VCR and satellite tuner or cable decoder.

Installing the batteries

Your SBC RU 240 needs two 1.5V batteries, type R03, UM4 or AAA. Put them in like this:

KEYS & FUNCTIONS

Power: to switch TV/VCR/SAT/AUX on and off.

Mode keys: to select TV, VCR, Satellite or AUX mode.

Mute: to switch the TV sound on and off.

To switch between the external inputs of your equipment.

Channel Up/Down: to select next / previous channel.

Volume Up/Down: to control the TV volume.

Number Keys: for direct channel selection and other functions.

To switch To switch to the last selected channel.

SHIFT: to get access to additional functions (press together

with other function keys). Depending on the age of

your equipment, the result is for example: SHIFT + P+: increases brightness or menu up function SHIFT + P-: decreases brightness or menu down function SHIFT + Volume+: increases colour or menu right function SHIFT + Volume-: decreases colour or menu left function

Instructions for use

English

Tip

• Remember to replace the batteries at least once a year.

• Don’t leave the batteries out for longer than one hour, otherwise you will need to set-up the SBC RU240 again.

Try other shift/key combinations on your equipment to discover which functions are available. Remember that you can’t get access to additional functions if these functions were not available on the original remote control of your equipment!

To operate menu control.

To confirm your selection.

VCR

Rewind

Record

Stop

Play

Forward

Pause

SET-UP FOR USE

Advice

Carefully read the complete procedure before starting!

Your equipment is a Philips brand:

1 Press the mode key for the device (TV, VCR, SAT or AUX)

you want to operate.

2 Press the power key to test.

– The green indicator LED lights up to confirm transmission

Check

Press a few keys to check correct response.

Your equipment is of another brand, or your equipment is a Philips brand, but not all keys respond correctly:

1 Press the mode key for the device (TV, VCR, SAT or AUX)

you want to operate.

2 Look up the brand name of the device you want to

operate in the code list.

Make sure you choose the correct code list for your device!

3 Make sure the device is switched on. 4 Press and hold keys 1 and 3 simultaneously - for about

three seconds- until the green LED lights up. (Release the keys: the green LED should stay on)

Instructions for use

English

5 Enter your 3-digit code using the number keys, within

30 seconds.

– The green LED flashes twice.

Check

That’s it! Press a few keys to check correct response. If response is not correct, repeat procedure beginning at step 1.

Note

- If the LED displays one long flash, the code was not recognised. Please go back to step 1 and repeat the procedure, using the next 3-digit code in the list.

- If no key is pressed within 30 seconds, you have to start again at step 1.

Advice

Carefully read the complete procedure before starting!

You do not know the brand of your equipment/you can not find the right code in the code list » auto search:

1 Press the mode selector key for the device (TV, VCR, SAT

or AUX) you want to operate.

2 Make sure the device is switched on (if the device is a

VCR, please insert a tape and start playback).

3 Press and hold keys 1 and 3 simultaneously -for about

three seconds- until the green LED lights up. (Release the keys: the green LED should stay on)

4 Press the power key to start the search. Make sure that

you keep the remote control pointed at your equipment.

– Each time the green LED flashes, another code is sent.

When the right code is found, the equipment switches off. Immediately press the power key to stop the search. If the green LED flashed again after the equipment switched off, this means you missed the correct code! If you missed the code, follow the next proccedure, starting at step 5. If the LED did not flash again after the equipment switched off, go to step 7.

5 Switch the equipment manually back on. 6 Press ‘P’ (down only!) repeatedly to send previous codes

until the equipment switches off again.

7 Press the power key to lock the correct code in the SBC

RU240’s memory.

– The green LED flashes twice.

Check

Switch equipment on manually. Press a few keys to check correct response. If response is not correct, repeat procedure beginning at step 1.

Instructions for use

English

Note

- The search time averages about 90 seconds. (Maximum search time is 5 minutes for TV, 2 minutes for VCR, 4 minutes for SAT and 5 minutes for AUX).

- Autosearch stops automatically after all codes have been tested.

MAKE A NOTE OF YOUR CODE!

Advice

Carefully read the complete procedure before starting!

Note the code inside the battery case and in the codelist of this booklet. This may be useful if you ever need to set up the SBC RU240 again. You used the auto search procedure or you forgot to note the code after set up? No problem! You can still ‘read out’ the code from the remote:

1 Make sure you have selected the right mode with the mode

selector key.

2 Press and release keys 1 and 6 simultaneously.

Important: after pressing the keys, you have to release them immediately!

– The green LED lights up.

3 Press the

the previous program

key.

– The green LED goes out.

4 Press key 1 and count the number of times the green LED

flashes. This is the first digit of the 3-digit code. (No flashes means the digit is zero.)

5 Press key 2 and count the number of flashes for the second

digit.

6 Press key 3 and count the number of flashes for the third

digit.

7 Note the code.

ADVANCED TIPS AND TRICKS

Advice

Carefully read the complete procedure before starting!

Changing the device keys

With the mode selector it is possible to select 4 categories of devices you want to operate. Each category (TV, VCR, SAT and AUX) is meant to operate a specific group of equipment:

TV VCR SAT AUX

tv vcr sat vcr

cable

Once you have programmed the functions of a device in one of the categories, it is not possible to program another device in the same category. There is, however, a solution in case you want to program two devices in the same category (2 TV’s, VCR’s, etc.). The following example explains how.

Instructions for use

English

EXAMPLE:

The AUX mode on this remote control is factory preset to control many Philips VCR’s. You can change the AUX mode (or any mode) to operate another type of device. The following example shows you how to use the AUX mode to operate a second TV:

1 Press the AUX key and make sure the second TV is

switched on.

2 Press and hold keys 1 and 6 simultaneously - for about 3

seconds - until the green LED lights up.

3 On the keypad, press keys 9, 9 and 2. 4 Press the TV key. 5 Press key 1.

– The LED flashes twice to indicate successful set up.

That’s it!

Don’t forget to set up the SBC RU240 to operate this second TV. See the section Set-up for use.

Punch-Through Sound

Punch-through sound enables you to control the audio level of your first or second TV, regardless of what device mode the remote control is in.

EXAMPLE:

You have installed a second TV under AUX mode. You can control that TV’s volume when you are in VCR mode. This feature is installed as a default setting for a first TV. To install this feature for a second TV:

1 Press the VCR key. 2 Press and hold keys 1 and 6 simultaneously -for about 3

seconds - until the green LED lights up.

3 On the keypad, press keys 9, 9, and 3. 4 Press the AUX key to select your second TV. 5 Press the power key.

– That’s it! The LED flashes twice to indicate successful set

up. The Volume up/down keys now control the volume of your second (AUX) TV when you’re in VCR or SAT mode.

Instructions for use

English

TROUBLESHOOTING GUIDE

• Problem:

– Solution:

• Device is not responding and the green light does not flash

when you press a button.

– Replace batteries with two new 1.5 volt, type RO3, UM4 or

AAA batteries.

• Device is not responding, but the green light does flash when

you press a button.

– Aim the SBC RU240 at the device and be sure that there are

no obstructions between the SBC RU240 and the device.

• The SBC RU240 is not performing commands properly.

– You may be using the wrong code. Try repeating Set up using

another code, listed under your brand, or start the Autosearch Set-up over again to locate the proper code. If the device still doesn’t respond, call the help-line and we’ll put you back on track.

• Having problems operating all the functions on your device.

– The SBC RU240 may just need customising for your model

type. Just call our help-line and we’ll put you back on track.

• Your brand is not listed in the code list.

– Try the hands-free Autosearch method.

• You want to reset the remote control to its factory preset.

– 1 Press and hold keys 1 and 6 simultaneously - for about

3 seconds - until the green LED lights up.

– 2 On the keypad, press keys 9, 8, and 1.

The LED flashes twice to indicate a successful reset.

NEED HELP?

If you have any questions about the SBC RU240, please call our help-line for assistance! You can find the number in the code list section of this booklet.

Before you call, please read this manual carefully. You will be able to solve most of your problems. If you don’t find an answer to your questions, make a note of your equipment in the table at the back of the code list section of this booklet. This makes it easier and faster for our operators to help you. Look for the model numbers in the equipment instruction manual, or on the back of your equipment. When calling our help-line please have your equipment close by, so our operators can help you verify the functionality of your remote control.

Instructions for use

English

¡Acaba de hacer una gran elección al comprar este control remoto Philips! Reemplaza hasta 4 controles remotos independientes y puede controlar las funciones más utilizadas de casi cualquier marca de TV, vídeo y sintonizador de satélite/decodificador por cable.

Instalación de las pilas

Su SBC RU240 necesita dos pilas de 1,5 V del tipo R03, UM4 o AAA. Colóquelas del siguiente modo:

TECLAS & FUNCIONES

Encendido: para encender y apagar TV/vídeo/SAT/AUX. Teclas del modo: para seleccionar el modo TV, vídeo, satélite o

aux. Silenciador: para apagar y encender el sonido de la televisión. para conmutar entre las entradas externas de su equipo.

Canal Arriba/Abajo: para seleccionar el canal siguiente / anterior. Volumen Arriba/Abajo: para controlar el volumen de la televisión. Teclas de números: para selección directa del canal y otras

funciones. para ir al último canal seleccionado. SHIFT: para acceder a funciones adicionales (pulsar junto con

otra tecla de función). En función de los años de su equipo, el resultado puede ser, por ejemplo:

SHIFT + P+: aumenta el brillo o ejecuta la función de menú

arriba.

SHIFT + P-: disminuye el brillo o ejecuta la función de menú

abajo.

SHIFT + Volumen+: aumenta el color o ejecuta la función de

menú derecha.

SHIFT + Volumen-: disminuye el color o ejecuta la función de

menú izquierda.

Instrucciones de manejo

Español

Indicación

• Acuérdese de cambiar las pilas al menos una vez al año.

• No deje el control sin pilas durante más de una hora o tendrá que volver a configurar de nuevo el SBC RU240.

Pruebe otras combinaciones de la tecla shift en su equipo para descubrir qué funciones están disponibles.¡Recuerde que no podrá acceder a funciones adicionales si estas funciones no están disponibles en el control remoto original de su equipo!

para accionar el control de Menú.

para confirmar su selección.

Vídeo

rebobinar

grabar

parar

reproducir

avance rápido

pausa

CONFIGURACIÓN PARA EL USO

Nota

¡Lea cuidadosamente y por completo el siguiente procedimiento antes de empezar!

Su equipo es marca Philips:

1 Pulse la tecla del modo correspondiente al dispositivo (TV,

vídeo, SAT o AUX) que desea controlar.

2 Pulse la tecla de encendido para realizar una prueba.

– El indicador LED verde se ilumina para confirmar transmisión.

Comprobación

Pulse algunas teclas para comprobar la respuesta correcta.

Su equipo es de otra marca o su equipo es de marca Philips, pero no todas las teclas responden correctamente

1 Pulse la tecla del modo correspondiente al dispositivo (TV,

vídeo, SAT o AUX) que desea controlar.

2 Busque el nombre de la marca del dispositivo que desea

controlar en la lista de códigos.

Asegúrese de que elige la lista de códigos correcta para su dispositivo.

3 Asegúrese de que su dispositivo está encendido. 4 Pulse y mantenga pulsadas las teclas 1 e 3 al mismo tiempo

- durante unos tres segundos – hasta que se encienda el LED verde. (Si suelta las teclas la luz verde ha de continuar encendida)

5 Introduzca el código de 3 dígitos utilizando las teclas de

número, en 30 segundos.

– El LED verde parpadea dos veces.

Instrucciones de manejo

Español

+ 19 hidden pages