Page 1
SACD1000
SACD1000
Instructions for use
Mode d'emploi
Instrucciones de manejo
00_SACD_USA_COV_23801_D1 11-12-2000 15:52 Pagina 1
Page 2
General information
Safety precautions
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
Laser safety
This unit employs a laser. To prevent possible eye injury, only a qualified service person
should remove the cover or attempt to service this device.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
CAUTION VISIBLE AND INVISIBLE LASER RADIATION. WHEN OPEN AVOID
EXPOSURE TO BEAM. (WARNING LOCATION: INSIDE ON LASER
COVERSHIELD)
NEVER MAKE OR CHANGE CONNECTIONS WITH THE POWER
SWITCHED ON.
For Customer Use:
Read carefully the information located on the back of your
SACD player and entered below the Serial N° Retain this
information for future reference.
Model N° is SACD 1000
Serial N° is __________________________
LASER
Type Semiconductor laser GaAlAs
Wavelength 650 nm (DVD)
780 nm (VCD/CD)
Output Power 7 mW (DVD)
10 mW (VCD/CD)
Beam divergence 60 degrees
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK ,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
USA C
00_SACD_USA_COV_23801_D1 11-12-2000 15:52 Pagina 2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CLASS 1
LASER PRODUCT
Page 3
3
Once your PHILIPS purchase is registered, you’re eligible to receive all the privileges of owning a PHILIPS product.
So complete and return the Warranty Registration Card enclosed with your purchase at once, and take advantage of
these important benefits.
Return your Warranty Registration card today to ensure
you receive all the benefits you’re entitled to.
Congratulations
on your
purchase,
and welcome to the
“family!”
Dear PHILIPS product owner:
Thank you for your confidence in PHILIPS. You’ve selected one of the best-built, best-backed products
available today. And we’ll do everything in our power to keep you happy with your purchase for many years
to come.
As a member of the PHILIPS “family,” you’re entitled to protection by one of the most comprehensive
warranties and outstanding service networks in the industry.
What’s more, your purchase guarantees you’ll receive all the information and special offers for which
you qualify, plus easy access to accessories from our convenient home shopping network.
And most importantly you can count on our uncompromising commitment to your total satisfaction.
All of this is our way of saying welcome–and thanks for investing in a PHILIPS product.
Sincerely,
Robert Minkhorst
President and Chief Executive Officer
Know these
safetysymbols
This “bolt of lightning” indicates uninsulated material within your unit may cause an electrical
shock.
For the safety of everyone in your household, please do not remove product covering.
The “exclamation point” calls attention to features for which you should read the enclosed
literature closely to prevent operating and maintenance problems.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO
RAIN OR MOISTURE.
CAUTION: To prevent electric shock, match wide blade of plug to wide slot, and fully insert.
ATTENTION: Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne
correspondante de la prise et pousser jusqu’au fond.
Warranty
Verification
Registering your product within
10 days confirms your right to
maximum protection under the
terms and conditions of your PHILIPS
warranty.
Owner
Confirmation
Your completed Warranty
Registration Card serves as
verification of ownership in the
event of product theft or loss.
Model
Registration
Returning your Warranty Registration
Card right away guarantees you’ll
receive all the information and special
offers which you qualify for as the
owner of your model.
P.S. Remember, to get the most from your PHILIPS
product, you must return your Warranty Registration
Card within 10 days. So please mail it to us right now!
R
E
G
I
S
T
R
A
T
I
O
N
N
E
E
D
E
D
W
I
T
H
I
N
1
0
D
A
Y
S
Hurry!
Visit our World Wide Web Site at http://www.philipsusa.com
00_SACD_USA_COV_23801_D1 11-12-2000 15:52 Pagina 3
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Page 4
4 GENERAL INFORMATION
Important safety instructions
1. Read Instructions - All the safety and operating instructions
should be read before the appliance is operated.
2. Retain Instructions - The safety and operating instructions
should be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the
operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions
should be followed.
5. Cleaning - Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
Exception: A product that is meant for uninterrupted service
and that for some specific reason, such as the possibility of the
loss of an authorization code for a CATV converter, is not
intended to be unplugged by the user for cleaning or any other
purpose, may exclude the reference to unplugging the appliance
in the cleaning description otherwise required in item 5.
6. Attachments - Do not use attachments not recommended
by the video product manufacturer as they may cause hazards.
7. Water and Moisture - Do not use this video product near
water - for example, near a bath tub, wash bowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming pool,
and the like.
8. Accessories - Do not place this video product on an
unstable cart, stand, tripod, bracket, or table. The video
product may fall, causing serious injury to a child or adult, and
serious damage to the appliance. Use only with a cart, stand,
tripod, bracket, or table recommended by the manufacturer or
sold with the video product. Any mounting of the appliance
should follow the manufacturer’s instructions and should use a
mounting accessory recommended by the manufacturer.
8A. An appliance and cart combination should be
moved with care. Quick stops, excessive force,
and uneven surfaces may cause the appliance and
cart combination to overturn.
9. Ventilation - Slots and openings in the cabinet are provided
for ventilation, to ensure reliable operation of the video
product, and to protect it from overheating. These openings
must not be blocked or covered. The openings should never
be blocked by placing the video product on a bed, sofa, rug, or
other similar surface. This video product should never be
placed near or over a radiator or heat register. This video
product should not be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
10. Power Sources - This video product should be operated
only from the type of power source indicated on the marking
label. If you are not sure of the type of power supply to your
home, consult your appliance supplier or local power company.
For video products intended to operate from battery power,
or other sources, refer to the operating instructions.
11. Polarization - This product may be equipped with a
polarized alternating-current line plug (a plug having one blade
wider than the other). This plug will fit into the power outlet
only one way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing the plug. If the
plug should still fail to fit, contact your electrician to replace
your obsolete outlet. Do not defeat the safety purpose of the
polarized plug.
12. Power-Cord Protection - Power supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the appliance.
13. Outdoor Antenna Grounding - If an outside antenna or
cable system is connected to the video product, be sure the
antenna or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Section 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors, location
of antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode. See Fig.A.
14. Lightning - For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power surges.
15. Power lines - An outside antenna system should not be
located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power
lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such
power lines or circuits as contact with them might be fatal.
16. Overloading - Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17. Object and Liquid Entry - Never push objects of any kind
into this product through openings as they may touch dangerous
voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product.
18. Servicing - Do not attempt to service this product yourself,
as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service
personnel.
19. Damage Requiring Service - Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled on, or objects have fallen into the
product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to its normal operation.
e. If the product has been dropped or the cabinet has been
damaged.
f. When the product exhibits a distinct change in performance
- this indicates a need for service.
20. Replacement Parts - When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufactu-rer or which have the same
characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock or other hazards.
21. Safety Check - Upon completion of any service or repairs
to this product, ask the service technician to perform safety
checks to determine that the product is in proper operating
condition.
22. Carts and Stands - The appliance should be used only with
a cart or stand that is recommended by the manufacturer.
23. Heat - The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products that produce heat.
00_SACD_USA_COV_23801_D1 11-12-2000 15:52 Pagina 4
EXAMPLE OF ANTENNA GROUNDING AS
PER NATIONAL ELECTRICAL CODE (NEC)
GROUND CLAMP
ELECTRIC SERVICE EQUIPMENT
ANTENNA LEAD
IN WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
GROUND
CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
Page 5
GENERAL INFORMATION 5
WARNING:
This device complies with Part 15 of the FCC (U.S.A.)
Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that may
cause undesired operation.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation! This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the supplier or an experienced radio/TV
technician for help.
IMPORTANT:
This product was FCC verified under test conditions
that included use of shielded cables and connectors
between system components. It is important that you
use shielded cables to reduce the possibility of causing
interference to radios, television sets, and other
electronic devices. If you have any problems, contact
your supplier.
Any change or modifications to the equipment by the
user not expressly approved by the grantee or
manufacturer could void the user's authority to operate
such equipment.
NOTE TO CATV SYSTEM INSTALLER:
This reminder is provided to call the CATV
(CableTV) system installer’s attention to
Article 820-40 of the NEC (National Electrical
Code) that provides guidelines for proper
grounding and, in particular, specifies that the
cable ground shall be connected to the
grounding system of the building, as close to
the point of cable entry as practical.
THIS DIGITAL APPARATUS DOES NOT EXCEED THE
CLASS B LIMITS FOR RADIO NOISE EMISSIONS FROM
DIGITAL APPARATUS AS SET OUT IN THE RADIO
INTERFERENCE REGULATIONS OF THE CANADIAN
DEPARTMENT OF COMMUNICATIONS.
CET APPAREIL NUMÉRIQUE N'ÉMET PAS DE BRUITS
RADIOÉLECTRIQUES DÉPASSANT LES LIMITES
APPLICABLES DANS LA RÈGLEMENT SUR LE BROUILLAGE
RADIOÉLECTRIQUES ÉDICTÉ PAR LE MINISTÈRE DES
COMMUNICATIONS DU CANADA.
00_SACD_USA_COV_23801_D1 11-12-2000 15:52 Pagina 5
Page 6
Specifications
PLAYBACK SYSTEM
SUPER AUDIO CD
DVD-Video
Video CD
Audio CD (CD-R and CD-RW)
OPTICAL READOUT SYSTEM
Laser type Semiconductor AlGaAs
Numerical Aperture 0.60 (SACD/DVD)
0.45 (VCD/CD)
Wavelenght 650 nm (SACD/DVD)
780 nm (VCD/CD)
AUDIO FORMAT
Digital DSD Uncompressed Digital
Dolby digital Compressed Digital
DTS/MPEG
PCM 16, 20, 24 bit
fs, 48, 96 kHz
Analog Sound Stereo
Dolby Surround™ downmix from multi-channel sound
3D Sound for virtual 5.1 channel sound on 2 speakers
SACD AUDIO PERFORMANCE
Multi-channel output (DSD stereo/multi-channel)
DA Converter 1 bit
SACD fs 2.8 MHz DC - 100 kHz
Max. output voltage (0dB) 2 V
RMS
+/- 0.3 V
Channel unbalance < 0.5 dB
Cut-off frequency normal mode 40kHz +/- 5 kHz
Cut-off frequency custom mode 50kHz +/- 5 kHz
Typical
Normal Custom
Amplitude linearity + 0.1/-0.6 + 0.1/-0.4
Total harmonic distortion
and noise (1 kHz) -100 dB -102 dB
Total harmonic distortion
and noise (20 Hz - kHz) -88 dB -95 dB
Inter-modulation distortion -107 dB -112 dB
Dynamic range -114 dB -111 dB
Signal-to-noise ratio (A-weighted) -114 dB -111 dB
Low level linearity (0 ➝ -100 dB) < +/- 0.1 dB
Low level linearity (0 ➝ -115 dB) < +/- 0.5 dB
Inter-channel phase < 1 degree
Crosstalk (1kHz) -130 dB
Crosstalk (20 Hz - 20 kHz) -100 dB
DVD/VCD/CD PERFORMANCE
DA Converter 24 bit
DVD fs 96 kHz 4 Hz - 44 kHz
fs 48 kHz 4 Hz - 22 kHz
Video CD fs 48 kHz 4 Hz - 22 kHz
CD fs 44.1 kHz 4 Hz - 20 kHz
Signal-Noise (1kHz) > 100 dB
Dynamic Range (1kHz) > 90 dB
Crosstalk (1kHz) > 105 dB
Distortion Noise (1kHz) > 90 dB
TV STANDARD EUROPE USA
(PAL/50Hz) (NTSC/60Hz)
Number of lines 625 525
Playback Multistandard (PAL/NTSC)
VIDEO FORMAT
Signal Digital
Signal handling Components
Digital Compression MPEG2 for DVD,
MPEG1 for VCD
VIDEO PERFORMANCE
Video output 1 Vpp into 75 ohm
S-Video output Y: 1 Vpp into 75 ohm
C: 0.300 Vpp into 75 ohm
RGB output 0.7 Vpp into 75 ohm
YPRPBoutput Y: 1Vpp into 75 ohm
PR: 0.7 Vpp into 75 ohm
PB: 0.7 Vpp into 75 ohm
Black Level Shift On/Off
Video Shift Left/Right
CONNECTIONS
Scart 2 Euroconnector
S-Video Output Mini DIN, 4 pin
Video Output 2 Cinch (yellow)
YPRPBOutput 3 Cinch
Analog Audio L+R output 2 Cinch (white/red)
Digital Audio Output 1 coaxial, 2 optical
IEC1937 for MPEG1, MPEG2 and AC-3
IEC61937 for DTS
POWER SUPPLY (UNIVERSAL)
Power Inlet 100-120V/220-240V, 50/60Hz
Power consumption 36 Watt
Power consumption standby less than 10 Watt
CABINET
Dimensions 435 x 110 x 330 (w x h x d)
Weight approx. 10kg
PACKAGE CONTENTS
SACD Player
Remote Control Handset with separately-packed batteries
2-core power cord
YPRPBcables
Audio cable
Video cable
Digital cable (coax)
User Manual
Warranty
00_SACD_USA_COV_23801_D1 11-12-2000 15:52 Pagina 6
Page 7
type no. of product • Numéro de série du produit
SACD1000
Date of purchase • Date d'achat • Kaufdatum • Koopdatum • Fecha de compra •
Data da compra • Data di acquisto • Købsdato • Kjøpedato • Inköpsdato • Ostopäivä
day • Jour month • Mois year • Année 20
Dealer's name, address and signature • Nom, adresse et signature du revendeur • Name,
Anschrift und Unterschrift des Händlers • Naam, adres en handtekening van de
handelaar • Nombre, dirección y firma del distribuidor • Nome, indirizzo e firma
del fornitore • Nome, morada e assinatura do vendedor • Forhandlerens navn, adresse
og underskrift • Återförsäljarens namn, adress och namnteckning • Myyjän nimi,
osoite ja allekirjoitus
©2000 PHILIPS Printed in Belgium. 3104 125 2380.1
IB8241T001
The products and services described herein are not necessarily available in all countries Due to continuous product improvements this document is subject to change without notice.
00_SACD_USA_COV_23801_D1 11-12-2000 15:52 Pagina 7
Loading...