Philips saa7377 DATASHEETS

INTEGRATED CIRCUITS

DATA SH EET

SAA7377

Digital servo processor and Compact Disc decoder (CD7)

Product speciﬁcations File under Integrated Circuits, IC01

1998 Jul 06

Philips Semiconductors Product speciﬁcations

Digital servo processor and Compact Disc decoder (CD7)

CONTENTS

1 FEATURES 2 GENERAL DESCRIPTION 3 QUICK REFERENCE DATA 4 ORDERING INFORMATION 5 BLOCK DIAGRAM 6 PINNING 7 FUNCTIONAL DESCRIPTION

7.1 Decoder part

7.1.1 Principle operational modes of the decoder

7.1.2 Crystal frequency selection

7.1.3 Standby modes

7.2 Crystal oscillator

7.3 Data slicer and clock regenerator

7.4 Demodulator

7.4.1 Frame sync protection

7.4.2 EFM demodulation

7.5 Subcode data processing

7.5.1 Q-channel processing

7.5.2 EIAJ 3 and 4-wire subcode (CD graphics) interfaces

7.5.3 V4 subcode interface

7.6 FIFO and error corrector

7.6.1 Flags output (CFLG)

7.6.2 C2FAIL

7.7 Audio functions

7.7.1 De-emphasis and phase linearity

7.7.2 Digital oversampling filter

7.7.3 Concealment

7.7.4 Mute, full scale, attenuation and fade

7.7.5 Peak detector

7.8 DAC interface

7.9 EBU interface

7.9.1 Format

7.10 KILL circuit

7.11 The VIA interface

7.12 Spindle motor control

7.12.1 Motor output modes

7.12.2 Spindle motor operating modes

7.12.3 Loop characteristics

7.12.4 FIFO overflow

7.13 Servo part

7.13.1 Diode signal processing

7.13.2 Signal conditioning

7.13.3 Focus servo system

7.13.4 Radial servo system

7.13.5 Off-track counting

7.13.6 Defect detection

7.13.7 Off-track detection

7.13.8 high-level features

7.13.9 Driver interface

7.13.10 Laser interface

7.13.11 Radial shock detector

7.14 Microcontroller interface

7.14.1 Microprocessor interface (4-wire bus mode)

7.14.2 Microcontroller interface (I2C-bus mode)

7.14.3 Summary of functions controlled by registers

7.14.4 Summary of servo commands

7.14.5 Summary of servo command parameters 8 LIMITING VALUES 9 OPERATING CHARACTERISTICS 10 OPERATING CHARACTERISTICS

11 OPERATING CHARACTERISTICS (I2S-BUS

12 OPERATING CHARACTERISTICS

13 APPLICATION INFORMATION 14 PACKAGE OUTLINE 15 SOLDERING

15.1 Introduction

15.2 Reflow soldering

15.3 Wave soldering

15.4 Repairing soldered joints 16 DEFINITIONS 17 LIFE SUPPORT APPLICATIONS 18 PURCHASE OF PHILIPS I2C COMPONENTS

SAA7377

0toF

(SUBCODE INTERFACE TIMING)

TIMING)

(MICROCONTROLLER INTERFACE TIMING)

1998 Jul 06 2

Philips Semiconductors Product speciﬁcations

Digital servo processor and Compact Disc decoder (CD7)

1 FEATURES

• Single-speed mode

• Full error correction strategy, t = 2 and e = 4

• Full CD graphics interface

• All standard decoder functions implemented digitally on

chip

• FIFO overflow concealment for rotational shock

resistance

• Digital audio interface (EBU), audio only

• 2 and 4 times oversampling integrated digital filter,

including f

• Audio data peak level detection

• Kill interface for DAC deactivation during digital silence

• All TDA1301 (DSIC2) digital servo functions, plus extra

high-level functions

• Low focus noise

• Improved playability on ABEX TCD-721R, TCD-725 and

TCD-714 discs

• Automatic closed loop gain control available for focus

and radial loops

• Pulsed sledge support

• Microcontroller loading LOW

• High-level servo control option

• High-level mechanism monitor

• Communication may be via TDA1301/SAA7345

compatible bus or I2C-bus

• On-chip clock multiplier allows the use of 8.4672 MHz

crystal.

mode

SAA7377

2 GENERAL DESCRIPTION

The SAA7377 is a single chip combining the functions of a CD decoder IC and digital servo IC. The decoder part is based on the SAA7345 (CD6) with an improved error correction strategy. The servo part is based on the TDA1301T (DSIC2) with improvements incorporated, extra features have also been added.

Supply of this Compact Disc IC does not convey an implied license under any patent right to use this IC in any Compact Disc application.

3 QUICK REFERENCE DATA

SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT

V I f T T

DD DD xtal

amb

stg

supply voltage 3.4 5.0 5.5 V supply current − 49 − mA crystal frequency 8 8.4672 35 MHz operating ambient temperature −40 − +85 °C storage temperature −55 − +125 °C

4 ORDERING INFORMATION

TYPE

NUMBER

NAME DESCRIPTION VERSION

SAA7377GP QFP64 plastic quad ﬂat package; 64 leads (lead length 1.6 mm);

PACKAGE

SOT393-1

body 14 × 14 × 2.7 mm

1998 Jul 06 3

Philips Semiconductors Product speciﬁcations

Digital servo processor and Compact Disc decoder (CD7)

5 BLOCK DIAGRAM

handbook, full pagewidth

SELPLL

CROUT

SCL SDA RAB SILD

HFIN

HFREF

ISLICE

TEST1 TEST2 TEST3

CRIN

CL16 CL11

CL4

SBSY SFSY

SUB RCK

D1 D2 D3 D4

3 4 5 7 10 1 12 16 2 19 32 39 49 56 30 47 59

GENERATOR

52 51 53 54

15 17

FRONT END

14 18

ref

20 23

TEST

13 21 22

TIMING

24 25 50

35 36 38 37

ADC

ref

MICROCONTROLLER

INTERFACE

DEMODULATOR

ADDRESSER

SUBCODE

PROCESSOR

SSA2VDDA1VSSD1VSSD3VDDD1(P)VDDD3(C)

SSA1VSSA3VDDA2VSSD2VSSD4VDDD2(P)

refT

PROCESSING

DIGITAL

PLL

EFM

SRAM

RAM

PRE-

CONTROL

FUNCTION

CONTROL

PART

SAA7377

PEAK

DETECT

AUDIO

PROCESSOR

OUTPUT STAGES

MOTOR

CONTROL

ERROR

CORRECTOR

FLAGS

EBU

INTERFACE

SAA7377

LDON

MOTO1

MOTO2

CFLG

C2FAIL

DOBM

DECODER

STATUS

RESET

MICRO-

CONTROLLER

INTERFACE

VERSATILE PINS

INTERFACE

62 63 42 41 40 43

V1 V2 V3 V4 V5 KILL

Fig.1 Block diagram.

1998 Jul 06 4

KILL

SERIAL DATA

INTERFACE

48 46 45 44

MGR291

SCLK WCLK DATA TEST4

Philips Semiconductors Product speciﬁcations

Digital servo processor and Compact Disc decoder (CD7)

6 PINNING

SYMBOL PIN DESCRIPTION

(1)

V V

SSA1 DDA1

(1)

2 D1 3 unipolar current input (central diode signal input) D2 4 unipolar current input (central diode signal input) D3 5 unipolar current input (central diode signal input) V

6 reference voltage input for ADC D4 7 unipolar current input (central diode signal input) R1 8 unipolar current input (satellite diode signal input) R2 9 unipolar current input (satellite diode signal input) I V V

refT

RH SSA2

10 current reference output for ADC calibration 11 reference voltage output from ADC

(1)

12 SELPLL 13 selects whether internal clock multiplier PLL is used ISLICE 14 current feedback output from data slicer HFIN 15 comparator signal input

(1)

SSA3

16 HFREF 17 comparator common mode input I

ref

DDA2

18 reference current output pin (nominally 0.5VDD)

(1)

19 TEST1 20 test control input 1; this pin should be tied LOW CRIN 21 crystal/resonator input CROUT 22 crystal/resonator output TEST2 23 test control input 2; this pin should be tied LOW CL16 24 16.9344 MHz system clock output CL11 25 11.2896 or 5.6448 MHz clock output (3-state) RA 26 radial actuator output FO 27 focus actuator output SL 28 sledge control output TEST3 29 test control input 3; this pin should be tied LOW V

DDD1(P)

(1)

DOBM 31 bi-phase mark output (externally buffered; 3-state) V

SSD1

(1)

MOTO1 33 motor output 1; versatile (3-state) MOTO2 34 motor output 2; versatile (3-state) SBSY 35 subcode block sync output (3-state) SFSY 36 subcode frame sync output (3-state) RCK 37 subcode clock input SUB 38 P-to-W subcode output bits (3-state) V

SSD2

(1)

V5 40 versatile output pin 5

analog ground 1 analog supply voltage 1

analog ground 2

analog ground 3

analog supply voltage 2

digital supply voltage 1 for periphery

digital ground 1

digital ground 2

SAA7377

1998 Jul 06 5

Philips Semiconductors Product speciﬁcations

Digital servo processor and Compact Disc

SAA7377

decoder (CD7)

SYMBOL PIN DESCRIPTION

V4 41 versatile output pin 4 V3 42 versatile output pin 3 (open-drain) KILL 43 kill output (programmable; open-drain) TEST4 44 test output pin; this pin should be left unconnected DATA 45 serial data output (3-state) WCLK 46 word clock output (3-state) V

DDD2(P)

SCLK 48 serial bit clock output (3-state) V

SSD3

CL4 50 4.2336 MHz microcontroller clock output SDA 51 microcontroller interface data I/O line (open-drain output) SCL 52 microcontroller interface clock line input RAB 53 microcontroller interface R/ SILD 54 microcontroller interface n.c. 55 not connected V

SSD4

RESET 57 power-on reset input (active LOW) STATUS 58 servo interrupt request line/decoder status register output (open-drain) V

DDD3(C)

C2FAIL 60 indication of correction failure output (open-drain) CFLG 61 correction ﬂag output (open-drain) V1 62 versatile input pin 1 V2 63 versatile input pin 2 LDON 64 laser drive on output (open-drain)

(1)

digital supply voltage 2 for periphery

digital ground 3

W and load control line input (4-wire bus mode)

R/W and load control line input (4-wire-bus mode)

digital ground 4

digital supply voltage 3 for core

Note

1. All supply pins must be connected to the same external power supply voltage.

1998 Jul 06 6

Philips Semiconductors Product speciﬁcations

Digital servo processor and Compact Disc decoder (CD7)

handbook, full pagewidth

C2FAIL 60

CRIN

DDD3(C)

STATUS

TEST2

CROUT

RESET 57

SAA7377

CL16

SSA1

DDA1

D1 D2 D3

RL D4

R1 R2

refT

SSA2

SELPLL

ISLICE

HFIN

SSA3

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16

LDONV2V1 64

ref

HFREF

DDA2

CFLG 61

TEST1

SSD4

V 56

CL11

n.c. 55

26 RA

SILD 54

27 FO

RAB 53

28 SL

SCL 52

TEST3

SDA

CL4

DOBM

DDD1(P)

SSD3

V 49

SSD1

48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33

SAA7377

SCLK V

DDD2(P)

WCLK DATA TEST4 KILL V3 V4 V5 V

SSD2

SUB RCK SFSY SBSY MOTO2 MOTO1

MGR292

Fig.2 Pin configuration.

1998 Jul 06 7

Philips Semiconductors Product speciﬁcations

Digital servo processor and Compact Disc decoder (CD7)

7 FUNCTIONAL DESCRIPTION

7.1 Decoder part

7.1.1 P The decoding part operates at single-speed and supports

a full audio specification. A simplified data flow through the decoder part is

illustrated in Fig.6.

7.1.2 C The SAA7377, which has an internal phase-locked loop

clock multiplier, can be used with 33.8688, 16.9344 or

8.4672 MHz crystal frequencies by setting register B and SELPLL as shown in Table 1. The internal clock multiplier, controlled by SELPLL, should only be used if a

8.4672 MHz crystal, ceramic resonator or external clock is present. It should be noted that the CL11 output is a

5.6448 MHz clock if a 16.9344 MHz external clock is used.

Table 1 Crystal frequency selection

7.1.3 S The SAA7377 may be placed in two standby modes

selected by register B (it should be noted that the device core is still active)

Standby 1: “CD-STOP” mode. Most I/O functions are switched off.

Standby 2: “CD-PAUSE” mode. Audio output features are switched off, but the motor loop, the motor output and the subcode interfaces remain active. This is also called a “Hot Pause”.

RINCIPLE OPERATIONAL MODES OF THE DECODER

RYSTAL FREQUENCY SELECTION

CRYSTAL FREQUENCY

(MHz)

00xx 0 33.8688 00xx 1 8.4672 01xx 0 16.9344

TANDBY MODES

SAA7377

CRIN, CROUT, CL16 and CL4: no interaction. Normal operation continues.

V1, V2, V3, V4, V5, CFLG and C2FAIL: no interaction. Normal operation continues.

7.2 Crystal oscillator

The crystal oscillator is a conventional 2 pin design operating between 8 and 35 MHz. This oscillator is capable of operating with ceramic resonators and also with both fundamental and third overtone crystals. External components should be used to suppress the fundamental output of the third overtone crystals as shown in Figs 3 and 4. Typical oscillation frequencies required are 8.4672,

16.9344 or 33.8688 MHz depending on the internal clock settings used and whether or not the clock multiplier is enabled.

SAA7377

OSCILLATOR

8.4672 MHz

330 Ω

100 kΩ

MGR293

Fig.3 8.4672 MHz fundamental configuration.

SAA7377

OSCILLATOR

CRINCROUT

22 pF22 pF

In the standby modes the various pins will have the following values;

MOTO1 and MOTO2: put in high-impedance, PWM mode (standby 1 and RESET, operating in standby 2). Put in high-impedance, PDM mode (standby 1 and RESET, operating in standby 2).

SCL, SDA, SILD and RAB: no interaction. Normal operation continues.

SCLK, WCLK, DATA, CL11 and DOBM: 3-state in both standby modes. Normal operation continues after reset.

1998 Jul 06 8

CROUT

MGR294

33.8688 MHz

330 Ω

100 kΩ

CRIN

3.3 µH

1 nF10 pF10 pF

Fig.4 33.8688 MHz overtone configuration.

Philips Semiconductors Product speciﬁcations

Digital servo processor and Compact Disc decoder (CD7)

7.3 Data slicer and clock regenerator

The SAA7377 has an integrated slice level comparator which can be clocked by the crystal frequency clock, or 8 times the crystal frequency clock (if SELPLL is set HIGH while using an 8.4672 MHz crystal, and register 4 is set to 0xxx). The slice level is controlled by an internal current source applied to an external capacitor under the control of the Digital Phase-Locked Loop (DPLL).

Regeneration of the bit clock is achieved with an internal fully digital PLL. No external components are required and the bit clock is not output. The PLL has two registers (8 and 9) for selecting bandwidth and equalization.

For certain applications an off-track input is necessary. This is internally connected from the servo part (its polarity can be changed by the foc_parm1 parameter), but may be input via the V1 pin if selected by register C. If this flag is HIGH, the SAA7377 will assume that its servo part is following on the wrong track and will flag all incoming HF data as incorrect.

7.4 Demodulator

SAA7377

The master counter is only reset if:

• A sync coincidence detected; sync pattern occurs 588 ±1 EFM clocks after the previous sync pattern

• A new sync pattern is detected within ±6 EFM clocks of its expected position.

The sync coincidence signal is also used to generate the PLL lock signal, which is active HIGH after 1 sync coincidence found, and reset LOW if, during 61 consecutive frames, no sync coincidence is found. The PLL lock signal can be accessed via the SDA or STATUS pins selected by register 2 and 7.

Also incorporated in the demodulator is a Run Length 2 (RL2) correction circuit. Every symbol detected as RL2 will be pushed back to RL3. To do this, the phase error of both edges of the RL2 symbol are compared and the correction is executed at the side with the highest error probability.

7.4.2 EFM DEMODULATION

The 14-bit EFM data and subcode words are decoded into 8-bit symbols.

7.4.1 F

RAME SYNC PROTECTION

A double timing system is used to protect the demodulator from erroneous sync patterns in the serial data.

input

2.2 nF

2.2 kΩ

22 kΩ

100 nF

47 pF

22 nF

SSA

HFIN

HFREF

SSA

ISLICE

ref

1/2V

100 µA

crystal

clock

DPLL

MGA368 - 1

Fig.5 Data slicer showing typical application components.

1998 Jul 06 9

This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in

_white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in

white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ...

1998 Jul 06 10

0 : reg D = xx01

CD GRAPHICS

INTERFACE

handbook, full pagewidth

SBSY SFSY SUB

Philips Semiconductors Product speciﬁcations

Digital servo processor and Compact Disc

decoder (CD7)

output from

data slicer

SUBCODE

PROCESSOR

DIGITAL PLL AND

DEMODULATOR

FIFO

ERROR

CORRECTOR

V4 SUBCODE

INTERFACE

FADE/MUTE/

INTERPOLATE

DIGITAL

FILTER

reg 3

KILL

reg F

KILL V3

MICROCONTROLLER

INTERFACE

1 : reg 3 = xx10

(1fs mode)

0 : reg 3 ≠ xx10

1 0

PHASE

COMPENSATION

DE-EMPHASIS

FILTER

1 0

SDA

EBU

INTERFACE

reg A

1 : no pre-emphasis detected OR reg D = 01xx (de-emphasis signal at V5) 0 : pre-emphasis detected AND reg D ≠ 01xx

1 0

INTERFACE

DOBM

I2S-BUS

reg 3

SCLK WCLK DATA

MGD039

reg C

Fig.6 Simplified data flow of decoder functions.

SAA7377

Philips Semiconductors Product speciﬁcations

Digital servo processor and Compact Disc decoder (CD7)

7.5 Subcode data processing

7.5.1 QThe 96-bit Q-channel word is accumulated in an internal

buffer. The last 16 bits are used internally to perform a Cyclic Redundancy Check (CRC). If the data is good, the SUBQREADY-I signal will go LOW. SUBQREADY-I can be read via the SDA or STATUS pins, selected via register 2. Good Q-channel data may be read from SDA.

7.5.2 EIAJ 3

Data from all the subcode channels (P-to-W) may be read via the subcode interface, which conforms to EIAJ CP-2401. The interface is enabled and configured as either a 3-wire or 4-wire interface via register F. The subcode interface output formats are illustrated in Fig.7, where the RCK signal is supplied by another device such as a CD graphics decoder.

CHANNEL PROCESSING

AND 4-WIRE SUBCODE (CD GRAPHICS)

INTERFACES

SAA7377

7.5.3 V4

Data of subcode channels, Q-to-W, may be read via pin V4 if selected via register D. The format is similar to RS232 and is illustrated in Fig.8. The subcode sync word is formed by a pause of 200 µs minimum. Each subcode byte starts with a logic 1 followed by 7 bits (Q-to-W). The gap between bytes is variable between 11.3 µs and 90 µs.

The subcode data is also available in the EBU output (DOBM) in a similar format.

SUBCODE INTERFACE

handbook, full pagewidth

SBSY

SFSY

RCK

SUB

SFSY

RCK

SUB

SF0 SF1

SF0 SF1 SF2 SF3 SF97 SF0 SF1

SFSY

RCK

SUB

SF2 SF3 SF97 SF0 SF1

P-W P-W P-W

EIAJ 4-wire subcode interface

P-W P-W P-W

EIAJ 3-wire subcode interface

PQRSTUVW

MBG410

Fig.7 EIAJ subcode (CD graphics) interface format.

1998 Jul 06 11

Philips Semiconductors Product speciﬁcations

Digital servo processor and Compact Disc decoder (CD7)

200 µs

min

W96 1QRSTUVW 1Q

7.6 FIFO and error corrector

The SAA7377 has a ±8 frame FIFO. The error corrector is a t = 2, e = 4 type, with error corrections on both C1 (32 symbol) and C2 (28 symbol) frames. Four symbols are used from each frame as parity symbols. This error corrector can correct up to two errors on the C1 level and up to four errors on the C2 level.

The error corrector also contains a flag processor. Flags are assigned to symbols when the error corrector cannot ascertain if the symbols are definitely good. C1 generates output flags which are read after (de-interleaving) by C2, to help in the generation of C2 output flags.

The C2 output flags are used by the interpolator for concealment of uncorrectable errors. They are also output via the EBU signal (DOBM).

11.3 µs

Fig.8 Subcode format and timing on pin V4.

SAA7377

11.3 µs min 90 µs max

MGD038

7.6.1 FLAGS OUTPUT (CFLG) The flags output pin CFLG (open-drain) shows the status

of the error corrector and interpolator and is updated every frame (7.35 kHz). In the SAA7377 chip a 1-bit flag is present on the CFLG pin as illustrated in Fig.9. This signal shows the status of the error corrector and interpolator.

The first flag bit, F1, is the absolute time sync signal, the FIFO-passed subcode sync and relates the position of the subcode sync to the audio data (DAC output). This flag may also be used in a super FIFO or in the synchronization of different players. The output flags can be made available at bit 4 of the EBU data format (LSB of the 24-bit data word), if selected by register A.

handbook, full pagewidth

33.9 µs

11.3 µs

F1 F2 F3 F4 F5 F6 F7 F8 F1F8

Fig.9 Flag output timing diagram.

1998 Jul 06 12

33.9 µs

MGD037

Philips Semiconductors Product speciﬁcations

Digital servo processor and Compact Disc decoder (CD7)

Table 2 Output ﬂags

F1 F2 F3 F4 F5 F6 F7 F8 DESCRIPTION

0xxxxxxxno absolute time sync 1xxxxxxxabsolute time sync x00xxxxxC1 frame contained no errors x01xxxxxC1 frame contained 1 error x10xxxxxC1 frame contained 2 errors x11xxxxxC1 frame uncorrectable x x x 0 0 x x 0 C2 frame contained no errors x x x 0 0 x x 1 C2 frame contained 1 error x x x 0 1 x x 0 C2 frame contained 2 errors x x x 0 1 x x 1 C2 frame contained 3 errors x x x 1 0 x x 0 C2 frame contained 4 errors x x x 1 1 x x 1 C2 frame uncorrectable xxxxx00xno interpolations xxxxx01xat least one 1 sample interpolation xxxxx10xat least one hold and no interpolations xxxxx11xat least one hold and one 1 sample interpolation

SAA7377

7.6.2 C2FAIL The C2FAIL pin indicates that invalid data has occurred on

the I2S-bus interface. However, due to the structure of the corrector it is impossible to determine which byte has failed. C2FAIL will go LOW for 140 µs when invalid data is detected, this data may then occur 15 ms before or after the pin is activated.

7.7 Audio functions

7.7.1 D When pre-emphasis is detected in the Q-channel

subcode, the digital filter automatically includes a de-emphasis filter section. When de-emphasis is not required, a phase compensation filter section controls the phase of the digital oversampling filter to ≤±1° within the band 0 to 16 kHz. With de-emphasis the filter is not phase linear.

If the de-emphasis signal is set to be available at V5, selected via register D, then the de-emphasis filter is bypassed.

7.7.2 D

E-EMPHASIS AND PHASE LINEARITY

IGITAL OVERSAMPLING FILTER

These attenuations do not include the sample-and-hold at the external DAC output or the DAC post filter. When using the oversampling filter, the output level is scaled −0.5 dB down, to avoid overflow on full-scale sine wave inputs (0 to 20 kHz).

Table 3 Filter speciﬁcation

PASS BAND STOP BAND ATTENUATION

0 to 9 kHz −≤0.001 dB

19 to 20 kHz −≤0.03 dB

− 24 kHz ≥25 dB

− 24 to 27 kHz ≥38 dB

− 27 to 35 kHz ≥40 dB

− 35 to 64 kHz ≥50 dB

− 64 to 68 kHz ≥31 dB

− 68 kHz ≥35 dB

− 69 to 88 kHz ≥40 dB

The SAA7377 contains a 2 to 4 times oversampling IIR filter. The filter specification of the 4 times oversampling filter is given in Table 3.

1998 Jul 06 13

Philips Semiconductors Product speciﬁcations

Digital servo processor and Compact Disc decoder (CD7)

7.7.3 CONCEALMENT A 1-sample linear interpolator becomes active if a single

sample is flagged as erroneous but cannot be corrected. The erroneous sample is replaced by a level midway between the preceding and following samples. Left and right channels have independent interpolators. If more than one consecutive non-correctable sample is found, the last good sample is held. A 1-sample linear interpolation is then performed before the next good sample (see Fig.10).

7.7.4 M A digital level controller is present on the SAA7377 which

performs the functions of soft mute, full scale, attenuation and fade; these are selected via register 0:

Mute: signal reduced to 0 in a maximum of 128 steps; 3 ms.

Attenuate: signal scaled by −12 dB. Full scale: ramp signal back to 0 dB level. From mute

takes 3 ms.

UTE, FULL SCALE, ATTENUATION AND FADE

SAA7377

Fade: activates a 128 stage counter which allows the signal to be scaled up/down by 0.07 dB steps

128 = full scale. 120 = −0.5 dB (i.e. full scale if oversampling filter

used). 32 = −12 dB. 0 = mute.

7.7.5 P The peak detector measures the highest audio level

(absolute value) on positive peaks for left and right channels. The 8 most significant bits are output in the Q-channel data in place of the CRC bits. Bits 81 to 88 contain the left peak value (bit 88 = MSB) and bits 89 to 96 contain the right peak value (bit 96 = MSB). The values are reset after reading Q-channel data via SDA.

EAK DETECTOR

Interpolation Hold Interpolation

OK Error OK Error Error Error OK OK

Fig.10 Concealment mechanism.

MGA372

1998 Jul 06 14

Philips Semiconductors Product speciﬁcations

Digital servo processor and Compact Disc

SAA7377

decoder (CD7)

7.8 DAC interface

The SAA7377 is compatible with a wide range of digital-to-analog converters (DACs). Nine formats are supported and are given in Table 4. Figures 11 and 12 show the Philips I2S-bus and the EIAJ data formats respectively. All formats are MSB first and fs is 44.1 kHz. The polarity of the WCLK and the data can be inverted; selectable by register 7.

Table 4 DAC interface formats

1110 f 0010 f 0110 f 0000 4f 0100 4f 1100 4f 0011 2f

0111 2f

1111 2f

SAMPLE

FREQUENCY

s s s

s s s s s s

NUMBER OF

BITS

(1)

16/18

SCLK (MHz) FORMAT INTERPOLATION

2.1168 Philips I2S-bus; 16/18 bits

(1)

16 2.1168 EIAJ 16 bits yes 18 2.1168 EIAJ 18 bits yes 16 8.4672 EIAJ 16 bits yes 18 8.4672 EIAJ 18 bits yes 18 8.4672 Philips I2S-bus; 18 bits yes 16 4.2336 EIAJ 16 bits yes 18 4.2336 EIAJ 18 bits yes 18 4.2336 Philips I2S-bus; 18 bits yes

yes

Note

1. In this mode the first 16 bits contain data, but if any of the fade, attenuate or de-emphasis filter functions are activated then the first 18 bits contain data.

1998 Jul 06 15

This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in

_white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in

white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ...

1998 Jul 06 16

SCLK

Philips Semiconductors Product speciﬁcations

Digital servo processor and Compact Disc

decoder (CD7)

WCLK

SCLK

WCLK

15 14

LEFT CHANNEL DATA (WCLK NORMAL POLARITY)

15 1410DATA

MGD036

Fig.11 Philips I2S-bus data format (16-bit word length shown).

LEFT CHANNEL DATA

170DATA

Fig.12 EIAJ data format (18-bit word length shown).

MGD035

SAA7377

Philips Semiconductors Product speciﬁcations

Digital servo processor and Compact Disc

SAA7377

decoder (CD7)

7.9 EBU interface

The bi-phase mark digital output signal at pin DOBM is in accordance with the format defined by the IEC958 specification. The DOBM pin can be held LOW and selected via register A.

Table 5 Format

FUNCTION BITS DESCRIPTION

Sync 0 to 3 − Auxiliary 4 to 7 not used; normally zero Error ﬂags 4 CFLG error and interpolation ﬂags when selected by register A Audio sample 8 to 27 ﬁrst 4 bits not used (always zero). 2’s compliment. LSB = bit 12, MSB = bit 27 Validity ﬂag 28 valid = logic 0 User data 29 used for subcode data (Q-to-W) Channel status 30 control bits and category code Parity bit 31 even parity for bits 4 to 30

7.9.1 FORMAT The digital audio output consists of 32-bit words

(‘subframes’) transmitted in bi-phase mark code (two transitions for a logic 1 and one transition for a logic 0). Words are transmitted in blocks of 384. Table 5 gives the formats.

Table 6 Description of Table5

FUNCTION DESCRIPTION

Sync The sync word is formed by violation of the bi-phase rule and therefore does not contain any data.

Its length is equivalent to 4 data bits. The 3 different sync patterns indicate the following situations: sync B: start of a block (384 words), word contains left sample; sync M: word contains left sample

(no block start) and sync W: word contains right sample. Audio sample Left and right samples are transmitted alternately. Validity ﬂag Audio samples are ﬂagged (bit 28 = 1) if an error has been detected but was uncorrectable. This

ﬂag remains the same even if data is taken after concealment. User data Subcode bits Q-to-W from the subcode section are transmitted via the user data bit. This data is

asynchronous with the block rate. Channel status The channel status bit is the same for left and right words. Therefore a block of 384 words contains

192 channel status bits. The category code is always CD. The bit assignment is given in Table 7.

Table 7 Bit assignment

FUNCTION BITS DESCRIPTION

Control 0 to 3 copy of CRC checked Q-channel control bits 0 to 3; bit 2 is logic 1 when copy

permitted; bit 3 is logic 1 when recording has pre-emphasis Reserved mode 4 to 7 always zero Category code 8to15 CD: bit 8 = logic 1, all other bits = logic 0 Clock accuracy 28 to 29 set by register A; 10 = level I; 00 = level II; 01 = level III Remaining 16 to 27 and

30 to 191

always zero

1998 Jul 06 17

+ 39 hidden pages

Philips saa7377 DATASHEETS

Specifications and Main Features

Frequently Asked Questions

User Manual

1 FEATURES

2 GENERAL DESCRIPTION

3 QUICK REFERENCE DATA

4 ORDERING INFORMATION

5 BLOCK DIAGRAM

6 PINNING

7 FUNCTIONAL DESCRIPTION

7.1 Decoder part

Table 1 Crystal frequency selection

7.2 Crystal oscillator

7.3 Data slicer and clock regenerator

7.4 Demodulator

7.4.2 EFM DEMODULATION

7.5 Subcode data processing

7.6 FIFO and error corrector

7.6.1 FLAGS OUTPUT (CFLG) The flags output pin CFLG (open-drain) shows the status

7.6.2 C2FAIL The C2FAIL pin indicates that invalid data has occurred on

7.7 Audio functions

7.7.3 CONCEALMENT A 1-sample linear interpolator becomes active if a single

7.8 DAC interface

7.9 EBU interface

Table 5 Format