Congratulations on your purchase and
welcome to Philips Norelco!
To fully benefit from the support that Philips
Norelco offers, register your product at
www.norelco.com/register
¡Felicitaciones en su compra y recepción
a Philips Norelco!
Beneficiar completamente de la ayuda
que las ofertas de Philips Norelco,
colocan su producto en
S9721
www.norelco.com/register
ENGLISH
4
IMPORTANT SAFETY
INSTRUCTIONS
When using an electric appliance, basic precautions should
always be followed, including the following:
Read all instructions before using this appliance.
DANGER
To reduce the risk of electric shock:
1. Do not reach for a corded shaver/SmartClean System that
has fallen into water. Unplug immediately.
2. Power plug and the accessories connected to it are not for
immersion or for use in shower.
3. Do not use an extension cord with this appliance.
4. Do not place or store a SmartClean System where it can
fall or be pulled into a tub or sink. Do not place or drop a
SmartClean System into water or other liquid.
5. Always unplug this shaver/SmartClean System from the
electrical outlet immediately after use, except when shaver/
SmartClean System is (re)charging.
6. Unplug and remove power supply cord from shaver
before cleaning.
7. The batteries used in this device may present a fire or
chemical burn hazard if mistreated. Do not disassemble, heat
above 100ºC (212°F) or incinerate.
WARNING
To reduce the risk of burns, fire, electric shock, or
injury to persons:
1. Close supervision is necessary when this shaver/SmartClean
System is used by, on, or near children or invalids.
2. Use this shaver/SmartClean System for its intended
household use as described in this manual. Do not use
attachments or a cleaning cartridge not recommended by
ENGLISH
Philips Electronics North America Corporation.
3. Never operate this shaver/SmartClean System if it has a
damaged cord or charging plug, if it is not working properly,
if it has been dropped or damaged, or dropped into water
while plugged in. For assistance call 1-800-243-3050.
4. Keep the shaver/SmartClean System, cord and charging plug
away from heated surfaces.
5. Never drop or insert any object into any opening.
6. Do not clean, charge or plug in shaver/SmartClean System
outdoors or operate where aerosol (spray) products are
being used or where oxygen is being administered.
7. Do not use this shaver with a damaged or broken comb, as
facial injury may occur.
8. Always attach plug to shaver/SmartClean System first, then
plug into outlet and then put razor in SmartClean System.
Be certain plug is inserted firmly into shaver, up to mark
indicated on plug. To disconnect, turn SmartClean System
off, remove charging plug from outlet.
9. Never put the shaver/SmartClean System in direct sunlight
or store at a temperature above 140°F (60°C).
10. Keep the cord dry at all times. Do not handle with wet
hands.
11. To prevent possible damage to the cord, do not wrap cord
around the shaver/SmartClean System.
12. Only use the power plug and other accessories supplied
with the appliance.
5
SAVE THESE
INSTRUCTIONS
IMPORTANT: The power plug contains a transformer. Do
not cut off the power plug to replace it with another plug, as
this will cause a hazardous condition.
ENGLISH
6
45 - DAY MONEY-BACK GUARANTEE
To enjoy the closest and most comfortable shave from your new Philips Norelco
Men’s Shaver, the shaver should be used exclusively for 3 weeks. This allows your
hair and skin enough time to adapt to the Philips Norelco Shaving System. If, after
that period of time, you are not fully satisfied with your Philips Norelco Men’s
Shaver, send the product back along with dated sales receipt and we’ll refund
you the full purchase price. The shaver must be shipped prepaid by insured
mail, insurance prepaid, have the original sales receipt, indicating purchase price, the date of purchase, and the money-back guarantee return
authorization form enclosed. We cannot be responsible for lost mail.
The shaver must be postmarked no later than 45 days from the date of purchase.
Philips Norelco reserves the right to verify the purchase price of the shaver and
limit refunds not to exceed suggested retail price.
To obtain money-back guarantee return authorization form,
call 1-800-243-3050 for assistance. Delivery of refund check will
occur 6–8 weeks AFTER receipt of returned product.
ENGLISH
Table of Contents
Features ...................................................... 8-11
connect the power cord to an electrical outlet.
When the battery symbol rapidly blinks, the
shaver contains enough energy for one shave.
-When the shaver is charging, the battery charge
percentage and battery symbol slowly blink white.
-The remaining battery capacity is indicated by
the battery charge percentages on the display.
◗ Full Charge Indicator
-When the battery has been fully charged,
C
the battery charge percentage lights up
continuously. After approximately 30 minutes the
display automatically switches off again.
-If the on/off button is pressed during or after
charging, the shaver will beep indicating the shaver
is still connected to the outlet.
◗ Remaining Battery Capacity
-The remaining battery capacity is indicated by
C
the battery charge percentage on the display.
◗ Low Battery Indicator
-When the battery is almost empty (5 or less
C
shaving minutes left), the battery indicator blinks
orange and you will hear a beep.
ENGLISH
◗ Personal Settings
C
Choose between three speed settings that best
fits your skin and hair type: slow for a more skinfriendly shave, normal for a thorough shave and
fast for a high powered shave. Press the – or +
buttons and the bar lights up white continuously.
◗ Replacement Shaving Unit Indicator
C
Every year, depending on your shaving behavior,
the replacement shaving unit indicator lights up
white continuously, the arrows blink white and
you will hear a beep. See 'Replacing the Shaving
Unit' section for instructions to reset the shaver.
This reminds you that with new shaving heads
you will guarantee yourself optimal shaving
performance.
◗ Blocked Shaving Heads Indicator
C
If the display shows a blinking replacement
shaving unit and faucet, a red exclamation mark
and the shaver beeps, clean the shaver thoroughly
before continuing to shave (see ‘Cleaning’). After
cleaning, if the blinking replacement shaving unit
and faucet with exclamation mark remain on the
display, immediately replace the shaving unit
(see ‘Replacing the Shaving Unit’).
13
◗ Cleaning Indicator
C
For optimal shaving performance, we
recommend cleaning the shaver after EACH use.
The blinking faucet will remind you the
shaving unit needs to be cleaned. This happens
after each shave.
ENGLISH
14
◗ Travel Lock
The shaver is equipped with a travel lock function.
You can use the travel lock function when you are
going to store the shaver for a longer period or if
you are going to take the shaver with you when
traveling. See ‘Travel Lock’ section for instructions
on how to use this function.
Charge Meter
◗ Charge Meter monitors amount of remaining
battery power available. Remaining battery
percentage is based on the amount of
power consumed shaving per minute and is
dependent upon your skin and beard type,
whether you use pre-shave lotion, and how
often the trimmer is used.
◗ Initially your shaver may need to go through 2
or 3 full charge/recharge cycles before
remaining battery charge percentage indicator
begins to display your accurate battery power
left.
Before First Use
◗ Charge the shaver before you start using it
(see ‘Charging’). Make sure the shaver is
switched off before you start charging it.
ENGLISH
◗ Remove any sticker or protective foil from
the display before using shaver.
Important
◗ Only use the power cord or SmartClean
System provided to charge the shaver.
◗ The power plug transforms 100-240V AC to
less than 24V DC.
15
Charging
◗ Charging, recharging or storing at
temperatures below 40ºF or higher than 95ºF
adversely affects lifetime of batteries.
◗ Charging or recharging requires one full hour.
◗ A fully charged shaver has a shaving time of up
to 50 minutes.
◗ You may recharge when the display indicates
the battery is almost empty.
◗ This shaver will not operate corded directly
from the electrical outlet.
◗ Do not charge shaver in a pouch.
1Connect cord directly to shaver (1) and
C
2
1
◗ An adaptor plug may be necessary for power
connect the power plug into any 100V to
240V AC outlet (2). Use only the power
cord provided.
cord usage in some foreign countries. Use
an attachment plug adaptor of the proper
configuration for the power outlet.
ENGLISH
16
The power cord will automatically conver t to
work on 100V to 240V AC systems.
2The display on the shaver will indicate
shaver is charging.
3Charging requires one full hour. A fully
charged shaver has a cordless shaving time
of up to 50 minutes.
Charging Shaver with SmartClean
System
1Connect the small plug to the SmartClean
System. Connect the power plug into any
100V to 240V AC outlet. Use only the
power cord provided.
2 Press the top cap to open the SmartClean
C
System.
3 Hold the shaver head side down above the
C
shaver holder.
ENGLISH
17
1
2
3
4Place the shaver into the holder (1), push
C
shaver back (2) and press down the top
cap to connect the shaver (3) (click).
The shaver will only fit in the SmartClean System
in one direction.
5 The battery symbol slowly blinks to
indicate shaver is charging.
6 Charging requires one full hour. A fully
charged shaver has a cordless shaving time
1
3
2
C
1Recharging requires one full hour.
of up to 50 minutes.
7 Press the top cap (1), pull the shaver
forward (2) and lift shaver from holder (3).
Recharging
Recharge when the display indicates the
battery is almost empty.
Quick Charge
When batteries are totally depleted, recharging
the shaver for approximately 3-5 minutes gives
enough energy for a 3-minute cordless shave.
Put It To The Test & Shaving Tips
◗ 21 Day Trial and Conversion Process. It is a fact
that your skin and beard need time to adjust to
a new shaving system.
ENGLISH
18
◗ Use your new shaver exclusively for 3 weeks to
fully enjoy the closeness of a Philips Norelco
shave.
◗ At first you may not get as close a shave as you
expect, or your face may even become slightly
irritated. This is normal since your beard and
skin will need time to adjust. Invest 3 weeks
and you’ll soon experience the full joy of your
new shaver.
◗ Stick with it! If you alternate shaving methods
during the adjustment period, it may make it
more difficult to adapt to the Philips Norelco
shaving system.
◗ If you are still not convinced after 21 days,
Philips Norelco will refund you the full
purchase price as long as the request is
received within 45 days of purchase.
How To Shave With An Electric
Shaver
C◗ This symbol on the shaver indicates that the
shaver can be used in the bath or shower.
◗ Make sure the SmartClean System does not
get wet or near water.
◗ Use this shaver for its intended household use
as described in this manual.
Shaving
◗ For best results pre-trim your beard if you
have not shaved for 3 days or longer.
ENGLISH
19
C 1 Turn shaver ON by pressing the on/off
button once. Shave against the direction
of beard growth using only circular
movements.
The shaver display will light up briefly.
B
Select your personal setting before using shaver.
(See 'Multi-Level Display' chapter).
2 Stretch your skin with your free hand so
blades can lift and cut whiskers. Gently
press shaver to skin so the floating heads
can follow the contours of your face.
DO NOT press too hard. Too much
pressure can pinch the skin into the combs.
3 Turn shaver OFF by pressing the on/off
button once.
The display lights up for a few seconds and then
shows the remaining battery charge percentage.
4 Clean the shaver after each use (see
chapter ‘Cleaning’).
C 5 Place the shaver in the SmartClean System
to protect shaver heads.
Wet Shaving
You can also use the shaver on a wet face with
shaving foam or gel.
C 1 Apply some water to your skin.
ENGLISH
20
C 2 Apply shaving foam or gel to your skin.
3 Rinse the shaving unit under the tap
to ensure that the shaving unit glides
smoothly over your skin.
4 Press the on/off button once to switch on
the shaver.
C 5 Move the shaving heads in circular
movements over your skin.
NOTE: Rinse the shaver under the tap regularly
to ensure that it continues to glide smoothly over
your skin.
6 Dry your face and thoroughly clean
the shaver after each use (see chapter
‘Cleaning’).
NOTE: Make sure you rinse all foam or gel off the
shaver.
7Place the shaver in the SmartClean System
C
to protect heads.
Trimming
To Groom Sideburns and Moustache:
1Pull the shaving unit straight off the shaver.
C
NOTE: Do not turn the shaving unit while you
pull it off the shaver.
ENGLISH
2Insert the raised notch of the trimmer into
C
C
5Trim beard, moustache or sideburns using
C
the slot in the top of the shaver. Press the
trimmer down to attach it to the shaver. You
will hear a ‘click’.
3 Turn shaver ON.
The display lights up for a few seconds.
4Hold trimmer to exact hairline desired.
Move trimmer downward with gentle
pressure.
the trimmer.
6 Turn shaver OFF when finished.
The display lights up for a few seconds and then
shows the remaining battery capacity charge
percentage.
7 Thoroughly clean the trimmer after using
(see ‘Cleaning’).
8 Pull the trimmer straight off the shaver.
NOTE: Do not turn or twist the trimming unit
while you pull it off the shaver.
21
9 Insert the raised notch of the shaving unit
C
into the slot in the top of the shaver. Press
the shaving unit down to attach it to the
shaver. You will hear a ‘click’.
ENGLISH
c.
22
10 Place the shaver in the SmartClean System
C
to protect heads.
Travel Lock
If you are going to store the shaver for a longer
time period or if traveling, it is possible to lock the
shaver. The travel lock prevents the shaver from
being switched on by accident.
Activating the travel lock
1Press the ON/OFF button for 3 seconds.
C
3 se
◗ The travel lock symbol lights up white
continuously.
◗ The shaver beeps and the lock symbol blinks.
2 The travel lock has now been activated.
Deactivating the travel lock
1Press the ON/OFF button for 3 seconds.
C 2The lock symbol blinks and then lights up
continuously. The shaver is now ready for
use.
B
The shaver unlocks automatically when charging in
the SmartClean System
ENGLISH
23
Cleaning
◗ Always clean your shaver after each use.
◗ Regular cleaning guarantees better shaving
results.
◗ Never remove or replace shaving unit while
motor is on.
◗ Do not apply pressure to shaving head combs.
Do not touch shaver heads with hard objects
as this may dent or damage precision-made
slotted combs.
◗ Do not use shaver if shaving head combs are
damaged or broken. Facial injury may occur.
◗ Do not use abrasives, scourers or aggressive
liquids such as gasoline or acetone to clean
the shaver.
Cleaning the Shaving Unit
The shaver heads may be quickly cleaned after
each use by rinsing with hot water. Water from
the tap should be on a hot setting, BUT BE
CAREFUL TO TEST WATER FIRST SO AS NOT
TO BURN OR SCALD HANDS.
◗ Regular cleaning guarantees better shaving
results.
◗ While rinsing shaver heads, water may drip
out of the base of shaver. This is a normal
occurrence.
ENGLISH
24
C 1 For best results rinse the shaving unit by
running under hot water for a few minutes.
2Pull the top portion of the shaving unit
C
C
4Carefully shake off excess water and let
5Press the top portion of the shaving unit
straight off the shaver.
3Rinse the shaving unit under hot tap water.
BE CAREFUL TO TEST WATER FIRST SO AS
NOT TO BURN OR SCALD HANDS.
the shaving unit air dry completely.
NOTE: Do not wipe or dry the shaving unit with
a towel or tissue. This could damage the shaving
heads.
down to attach it to the shaver head
holder. You will hear a ‘click’.
ENGLISH
25
Preparing SmartClean System Pro
For Use
CAUTION: Keep cleaning cartridge(s) out of
reach of children. Do not take internally. Avoid
contact with eyes. In case of eye contact,
thoroughly flush with cold water. If irritation
persists, get medical attention.
Important
◗ Only use this shaver, Smart
cleaning cartridge provided to charge or clean
shaver.
◗ Other Philips Norelco shavers may not work
with this
◗ For optimal cleaning results, replace the
cleaning cartridge every 3 months.
◗ To avoid evaporation, do not expose cleaning
solution to direct sunlight.
◗ The SmartClean System thoroughly cleans but
does not disinfect your shaver, therefore, do
not share shaver with others.
◗ The charging plug converts 100-240V AC to
less than 24V DC.
◗ Place the
stable and fluid-resistant surface to avoid any
leakage. Be careful not to tip or move the
SmartClean System
◗ Use this appliance for its intended household
use as described in this manual.
SmartClean System.
SmartClean System
Clean System
on a flat,
when it is ready for use.
and
C 1 Place the SmartClean System on a flat, level
surface.
Loading...
+ 53 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.