Philips S7000, S7910 Series Manual
Shaver S7000
S7910
S791
0
Wet & Dry
1
1
12
13
14
15
2
3
4
5
6
7
8
10
11
9
empty page before TOC
English 6
Français (Canada) 32
English
6
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benefit from the support that
Philips offers, register your product easily via the
app or at
http://www.philips.com/s7000-support.
Download the GroomTribe app to create your
Personal Shaving Plan today. It will provide you
ongoing guidance on how to tackle your skin issue.
The app also tracks your shaving routine and
adjusts your shaver's settings in line with your plan.
Important safety information
Read this important information carefully before
you use the appliance and its accessories and save
it for future reference. The accessories supplied
may vary for different products.
Danger
- Keep the supply unit dry.
Warning
- To charge the battery, only use the detachable
supply unit (type HQ8505) provided with the
appliance.
- The supply unit contains a transformer. Do not
cut off the supply unit to replace it with another
plug, as this causes a hazardous situation.
English
Caution
English
- Children shall not play with the appliance.
Cleaning and user maintenance shall not be
made by children without supervision.
- Always unplug the shaver before you clean it
under the tap.
- Always check the appliance before you use it.
Do not use the appliance if it is damaged, as
this may cause injury. Always replace a
damaged part with one of the original type.
- Do not open the appliance to replace the
rechargeable battery.
- This appliance contains batteries that are nonreplaceable.
- Never use water hotter than 60°C to rinse the
shaver.
- Only use this appliance for its intended purpose
as shown in the user manual.
- For hygienic reasons, the appliance should only
be used by one person.
- Never use compressed air, scouring pads,
abrasive cleaning agents or aggressive liquids
such as petrol or acetone to clean the
appliance.
- Water may drip from the socket at the bottom
of the shaver when you rinse it. This is normal
and not dangerous because all electronics are
enclosed in a sealed power unit inside the
shaver.
- Do not use the supply unit in or near wall
sockets that contain an electric air freshener to
prevent irreparable damage to the supply unit.
- Be careful when handling your smartphone
near water and in moist environments.
- The shortwave radio frequency signals of a
Bluetooth® appliance may impair the operation
of other electronic and medical devices.
7
English
8
- Switch off Bluetooth where it is prohibited.
- Do not use the appliance in medical facilities,
aircraft, refuelling points, close to automatic
doors, automatic fire alarms or other
automatically controlled devices.
- Keep this appliance at least 20 cm from
pacemakers and other medical devices. Radio
waves may impair the operation of pacemakers
and other medical devices.
Electromagnetic fields (EMF)
This Philips appliance complies with all applicable
standards and regulations regarding exposure to
electromagnetic fields.
Radio Equipment Directive
- The frequency band in which the appliance
operates is 2.4 GHz.
- This appliance is equipped with Bluetooth class
2.
- The maximum radio frequency power radiated
in the frequency band in which the appliance
operates is less than 20 dBm.
- This equipment has been so constructed that
the product complies with the requirement of
Article 10(2) as it can be operated in at least one
EU Member State as examined and the product
is compliant with Article 10(10) as it has no
restrictions on putting into service in all EU
member states.
- Hereby Philips declares that this appliance is in
compliance with the essential requirements and
other relevant provisions of Directive
2014/53/EU. The declaration of conformity may
be consulted at www.philips.com/support.
General
English
- This shaver is waterproof. It is suitable for use in
the bath or shower and for cleaning under the
tap. For safety reasons, the shaver can
therefore only be used without cord.
- The supply unit is suitable for mains voltages
ranging from 100 to 240 volts.
- The supply unit transforms 100-240 volts to a
safe low voltage of less than 24 volts.
- The Bluetooth® wordmark and logos are
registered trademarks owned by Bluetooth SIG,
Inc. and any use of such marks by Koninklijke
Philips N.V. is under license.
- Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
- This device complies with ISED license-exempt
RSS(s). Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
- This device complies with the ISED RF exposure
limits and has been evaluated in compliance
with portable exposure condition.
- There is no limitation as to which distance can
be used from the human body.
- This Class B digital apparatus complies with
Canadian ICES-003.
9
General description (Fig. 1)
1 Click-on precision trimmer attachment
2 Click-on shaving unit
3 On/off button
4 Notification symbol
English
10
5 Sensitive shave setting XS
6 Sensitive shave setting S
7 Cleaning reminder
8 Travel lock symbol
9 Unplug for use reminder
10 Battery charge indicator
11 Socket for small plug
12 Supply unit
13 Small plug
14 Cleaning brush
15 Pouch
The display
Notification symbol
The shaver is equipped with a notification symbol.
The notification symbol lights up when there is an
important message for you in the app. When it
lights up, simply open the app on your smartphone
and follow the easy tips that the app gives you. If
you need further support, visit
www.philips.com/s7000-support.
Sensitive shave settings
The shaver has a feature that allows you to
personalize your shave settings using the app.
Choose between three settings depending on your
personal shaving needs: extra sensitive (xs),
sensitive (s) and normal. Select your preferred
setting 'xs', 's' or 'normal' in the app to activate it on
your shaver. By default the setting is set on
sensitive (s).
Note: The sensitivity settings can only be adjusted
by using the app.
Cleaning reminder
3 sec.
Clean the shaver after every use for optimal
performance (see 'Cleaning and maintenance').
The cleaning reminder flashes to remind you to
clean the shaver.
Travel lock
When you are going to travel, you can lock the
shaver to prevent it from accidentally switching on.
The travel lock also deactivates Bluetooth.
'Unplug for use' reminder
The ‘unplug for use’ reminder flashes to remind
you to disconnect the shaver from the wall socket
before you can switch it on.
Note: This shaver is waterproof. It is suitable for
use in the bath or shower and for cleaning under
the tap. For safety reasons, the shaver can only be
used without cord.
Charging
Quick charge: After approx. 5 minutes of charging,
the shaver contains enough power for one shave.
At that moment, the battery charge indicator stops
flashing quickly and starts flashing slowly.
English
11
3 sec.
English
12
When the shaver continues charging, the battery
charge indicator on the shaver flashes white
slowly.
Battery fully charged
When the battery is fully charged, the battery
charge indicator lights up white continuously.
Note: When the battery is full, the display switches
off automatically after 30 minutes.
Note: This shaver can only be used without cord. If
you press the on/off button during charging, the
unplug for use reminder lights up white to remind
you that you have to disconnect the shaver from
the wall socket.
Battery low
When the battery is almost empty, the battery
charge indicator flashes orange. At this point there
is enough energy left for one shave.
Bluetooth® connection
The shaver is equipped with Bluetooth® 4.1 to
connect your shaver to the app. Bluetooth is
automatically activated when you switch on the
shaver for the first time.
You can only deactivate it by activating the travel
lock.
Note: Make sure your smartphone is equipped
with Bluetooth 4.1 or higher.
Charging
1
2
Charge the shaver before you use it for the first
time and when the display indicates that the
battery is almost empty.
Charging takes approx. 1 hour. A fully charged
shaver has a shaving timeof up to 50 minutes.
Note: You cannot use the shaver while it is
charging.
Quick charge
After approx. 5 minutes of charging the shaver
contains enough power for one shave.
Charging with the supply unit
1 Make sure the shaver is switched off.
2 Put the small plug in the shaver and put the
supply unit in the wall socket.
The display of the shaver indicates that the
shaver is charging.
3 After charging, remove the supply unit from the
wall socket and pull the small plug out of the
shaver.
Note: When the battery is full, the display
switches off automatically after 30 minutes.
Preparing for use
Pair the shaver and smartphone
The app is compatible with a wide range of iPhone
and Android™ smartphones.
More information is available at
www.philips.com/s7000-support.
1 Download the app from your app store.
English
13
S7920
English
14
2 Make sure Bluetooth on the smartphone is
switched on.
3 Switch on the shaver.
4 Open the app and follow the instructions to
start the pairing process.
5 When paired, the shaver and app will connect
automatically when you open the app. Simply
keep the app open and Bluetooth on.
Unpair the shaver and smartphone
Pairing allows a connection between 1 shaver and 1
smartphone. To remove this connection (e.g. when
you have a new smartphone), use the following
steps:
1 Unpair the shaver: press and hold the on/off
button on the handle for approx. 10 seconds to
remove the bond between shaver and app.
Note: The unpairing of the shaver is successful
when the notification symbol lights up 4 times
briefly.
2 Unpair your smartphone: go to 'Settings' on
your smartphone and select Bluetooth. Then
select ' Shaver S79xx' and press 'forget' or
'unpair'.
Note: The unpairing procedure may vary per
smartphone. Please check your smartphone
manual for more information.
Using the shaver
Always check the shaver and all accessories
before use. Do not use the shaver or any
accessory if it is damaged, as this may cause
injury. Always replace a damaged part with one of
the original type.
Note: This shaver is waterproof. It is suitable for
use in the bath or shower and for cleaning under
the tap. For safety reasons, the shaver can only be
used without cord.
Switching the shaver on and off
1 To switch on the shaver, press the on/off
button once.
2 To switch off the shaver, press the on/off
button once.
Connect with the shaver
1 Make sure Bluetooth on the smartphone is
switched on.
2 Open the app on the smartphone.
3 When paired (see 'Pair the shaver and
smartphone'), the shaver and the app will
connect automatically. You can now start
shaving.
Note: Make sure you have a good Bluetooth
and Internet connection to fully benefit from
the app.
4 Keep the smartphone and shaver close to each
other in order to stay connected and
synchronize your shaves.
Synchronize your shaves
The shaver can store data of up to 20 shaves, so
you don't have to shave with your phone near you
every time. However, to prevent data loss,
synchronize the shaver with the app once every 20
shaves.
English
15
English
16
Shaving advice
Shaving
1 Make sure you are close to the shaver and open
the app.
2 The app connects automatically and
synchronizes your last shaves.
There are 2 ways to obtain advice: guided shave
real time or synchronized shave. We advise you to
start with the guided shave to enhance your
shaving experience. Correct handling of your
shaver will contribute to the best shaving result.
Next, follow the advice obtained from the
synchronized shaves and the personalized
programs.
Skin adaptation period
Your first shaves may not bring you the result you
expect and your skin may even become slightly
irritated. This is normal. Your skin needs time to
adapt to any new shaving system.
Follow the advice provided by the app and shave
regularly (at least 3 times a week) with this shaver
for a period of 3-4 weeks to allow your skin to
adapt to the new shaver.
Shaving tips
- For the best results on skin comfort, pre-trim
your beard if you have not shaved for 3 days or
longer.
- Move the shaving heads over your skin in
circular movements.
- Keep each shaving head fully in contact with
your skin.
- Exert gentle pressure for a close, comfortable
shave.
English
Dry shaving
1 Switch on the shaver.
2 Move the shaving heads over your skin in
circular movements to catch all hairs growing in
different directions. Make sure each shaving
head is fully in contact with the skin. Exert
gentle pressure for a close, comfortable shave.
Note: Do not press too hard, as this can cause
skin irritation.
3 Switch off and clean the shaver after each use
(see 'Cleaning and maintenance').
Wet shaving
For a more refreshing shave, you can also use this
shaver on a wet face with a shaving gel or foam for
sensitive skin.
1 Apply some water to your skin.
2 Apply shaving foam or gel to your skin.
3 Rinse the shaving unit with lukewarm water to
ensure that the shaving unit glides smoothly
over your skin.
4 Switch on the shaver.
5 Move the shaving heads over your skin in
circular movements to catch all hairs growing in
different directions. Make sure each shaving
head is fully in contact with the skin. Exert
gentle pressure for a close, comfortable shave.
Note: Do not press too hard, this can cause skin
irritation.
17
English
18
Note: Rinse the shaving unit regularly to ensure
that it continues to glide smoothly over your
skin.
6 Dry your face.
7 Switch off and clean the shaver after each use
(see 'Cleaning and maintenance').
Note: Make sure that you rinse all shaving gel off
the shaver.
Using click-on attachments
Using the precision trimmer attachment
You can use the precision trimmer attachment to
touch up your beard, sideburns and moustache.
1 Make sure the shaver is switched off.
2 Pull the attachment straight off the shaver.
Note: Do not twist the attachment while you
pull it off the shaver.
3 Attach the precision trimmer attachment to the
shaver ('click').
4 Switch on the shaver.
5 Hold the trimmer perpendicular to the skin and
move the shaver downwards while you exert
gentle pressure.
6 Clean the attachment after use.
Cleaning and maintenance
Regular cleaning guarantees better shaving
results.
Never clean, remove or replace the shaving
unit while the shaver is switched on.
Do not apply pressure to shaving head guards.
Do not touch shaving heads with hard objects
as this may dent or damage the precisionmade slotted guards.
Do not use compressed air, abrasives, scourers
or aggressive liquids such as petrol or acetone
to clean the shaver.
Cleaning the shaver under the tap
Clean the shaver after every shave for optimal
shaving performance.
Always check if the water is too hot, to prevent
burning your hands.
Never dry the shaving unit with a towel or tissue,
as this may damage the shaving heads.
While rinsing the shaving unit, water may drip out
of the bottom of the shaver. This is a normal
occurrence. The electronics are secured in a
watertight inner body.
1 Switch on the shaver.
2 Rinse the shaving unit with warm water.
English
19
Loading...