Philips S5620, S5600, S5420, S5400, S5380 User Manual

...

S5620, S5600, S5420, S5400, S5380, S5230

English Français (Canada)

English

Introduction

Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome.

Please read this user manual, as it contains information about the features of this shaver as well as some tips to make shaving easier and more enjoyable.

General description

1 Protection cap for shaving unit

(S5420,S5400,S5380,S5230 only) 2 Click-on shaving unit 3 On/off button 4 Turbo button (S5620,S5380 only) 5 Handle 6 Socket for small plug 7 Battery charge indicator with 1 light

(S5420,S5400,S5230 only) 8 Battery charge indicator with 3 lights

(S5620,S5600,S5380 only) 9 Unplug for use symbol 10 Travel lock symbol 11 Replacement reminder 12 Cleaning reminder 13 Click-on trimmer attachment

(S5600,S5420,S5400,S5380,S5230 only) 14 Click-on beard styler attachment (S5620 only) 15 Comb for beard styler attachment (S5620 only) 16 Adapter 17 Small plug 18 Pouch (S5620,S5600 only)

English

Important safety information

Read this important information carefully before you use the appliance and its accessories and save it for future reference. The accessories supplied may vary for different products.

Danger

- Keep the adapter dry ().

Warning

- The adapter contains a transformer. Do not cut off

the adapter to replace it with another plug, as this

causes a hazardous situation.

- This appliance can be used by children aged from 8

years and above and persons with reduced

physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given

supervision or instruction concerning use of the

appliance in a safe way and understand the hazards

involved. Children shall not play with the appliance.

Cleaning and user maintenance shall not be made

by children without supervision.

- Always unplug the shaver before you clean it

under the tap.

- Always check the appliance before you use it. Do

not use the appliance if it is damaged, as this may

cause injury. Always replace a damaged part with

one of the original type.

English

Caution

- Never immerse the adapter in water nor rinse it

under the tap.

- Never use water hotter than 80°C to rinse the

shaver.

- Only use this appliance for its intended purpose as

shown in the user manual.

- For hygienic reasons, the appliance should only be

used by one person.

- Never use compressed air, scouring pads, abrasive

cleaning agents or aggressive liquids such as petrol

or acetone to clean the appliance.

- Water may drip from the socket at the bottom of

the shaver when you rinse it. This is normal and

not dangerous because all electronics are enclosed

in a sealed power unit inside the shaver.

Electromagnetic fields (EMF)

- This Philips appliance complies with all applicable

standards and regulations regarding exposure to

electromagnetic fields.

General

- This shaver is waterproof (). It is suitable for use in

the bath or shower and for cleaning under the tap.

For safety reasons, the shaver can therefore only

be used without cord.

- The appliance is suitable for voltages ranging from

100 to 240 volts.

- The adapter transforms 100-240 volts to a safe

low voltage of less than 24 volts.

- Maximum noise level: Lc = 69dB(A)

English

The display

Charging

Battery charge indicator with 3 lights (specific types only)

- Charging takes approx. 1 hour.

- Quick charge: When the appliance is connected to

the power outlet, the lights of the battery charge

indicator light up one after the other continuously.

When the appliance contains enough energy for

one shave, the bottom light of the battery charge

indicator flashes slowly.

- If you leave the appliance connected to the power

outlet, the charging process continues. To indicate

that the appliance is charging, first the bottom light

flashes and then lights up continuously. Then the

second light flashes and then lights up continuously,

and so on until the appliance is fully charged.

Battery charge indicator with 1 light (specific types only)

- Charging takes approx. 1 hour.

- Quick charge: When the appliance does not

contain enough energy for one shave, the battery

charge indicator flashes quickly. When the battery

charge indicator starts flashing slowly, the appliance

contains enough energy for one shave .

- If you leave the appliance connected to the power

outlet, the charging process continues. To indicate

that the appliance is charging, the battery charge

indicator flashes slowly.

English

Battery fully charged

Note: This appliance can only be used without cord. Note: When the battery is full, the display switches off

automatically after 30 minutes. Note: If you press the on/off button during charging, the

'unplug for use' symbol flashes white to remind you that you have to disconnect the appliance from the power outlet.

When the battery is full, all lights of the battery charge indicator light up continuously.

- Battery charge indicator with 3 lights (specific types

only)

- Battery charge indicator with 1 light (specific types

only)

Battery low

When the battery is almost empty, the battery charge indicator flashes orange.

- Battery charge indicator with 3 lights (specific types

only)

English

- Battery charge indicator with 1 light (specific types

only)

Remaining battery capacity

Battery charge indicator with 3 lights (specific types only)

- The remaining battery capacity is indicated by the

lights of the battery charge indicator that light up

continuously.

’Unplug for use’ reminder

- The appliance is equipped with an ‘unplug for use’

reminder. The ‘unplug for use’ symbol flashes to

remind you that you have to disconnect the

appliance from the adapter before you can switch

it on.

Cleaning reminder

Clean the shaver after every shave for optimal performance. When you switch off the shaver, the cleaning reminder flashes to remind you to clean the shaver.

3 sec.

English

Travel lock

You can lock the shaver when you are going to travel. The travel lock prevents the shaver from being switched on by accident.

Activating the travel lock

Press the on/off button for 3 seconds to enter the

travel lock mode.

While you activate the travel lock, the travel lock symbol lights up continuously. When the travel lock is activated, the travel lock symbol flashes.

Deactivating the travel lock

Press the on/off button for 3 seconds.

The travel lock symbol flashes and then lights up continuously. The shaver is now ready for use again.

Replacing shaving heads

For maximum shaving performance, we advise you to replace the shaving heads once a year.

- The appliance is equipped with a replacement

reminder which reminds you to replace the shaving

heads. The replacement reminder lights up

continuously.

English

Note: After replacing the shaving heads, you need to reset the replacement reminder by pressing the on/off button for 7 seconds.

Turbo setting (specific types only)

The appliance is equipped with a Turbo setting. This allows you to shave hard-to-reach areas more quickly.

Charging

Charging takes approx. 1 hour. Note: You cannot use the appliance while charging. Charge the shaver before you use it for the first time

and when the display indicates that the battery is almost empty.

Charging with the adapter

Make sure the appliance is switched off.

Put the adapter in the wall socket (1) and put the

small plug in the appliance (2).

After charging, remove the adapter from the wall

socket and pull the small plug out of the appliance.

English

Using the appliance

Switching the appliance on and off

To switch on the appliance, press the on/off button

once.

To switch off the appliance, press the on/off button

once. Battery charge indicator with 3 lights (specific types

only): the display lights up for a few seconds to show the remaining battery status.

Shaving

Skin adaption period

Your first shaves may not bring you the result you expect and your skin may even become slightly irritated. This is normal. Your skin and beard need time to adapt to any new shaving system. We advise you to shave regularly (at least 3 times a week) and exclusively with this shaver for a period of 3 weeks to allow your skin to adapt to the new shaver.

Note: This appliance can only be used without cord.

Switch on the appliance.

Move the shaving heads over your skin in circular

movements.

Clean the shaver after use (see 'Cleaning and

maintenance').

Wet shaving

You can also use this shaver on a wet face with shaving foam or shaving gel.

To shave with shaving foam or shaving gel, follow the steps below:

English

Apply some water to your skin.

Apply shaving foam or shaving gel to your skin.

Rinse the shaving unit under the tap to ensure that

the shaving unit glides smoothly over your skin.

Switch on the appliance.

Move the shaving heads over your skin in circular

movements.

Note: Rinse the shaving unit regularly to ensure that

it continues to glide smoothly over your skin.

Dry your face.

Clean the shaver after use (see 'Cleaning and

maintenance').

Note: Make sure you rinse all foam or shaving gel off the shaver.

Turbo setting (specific types only)

The appliance is equipped with a Turbo setting. This allows you to shave hard-to-reach areas more quickly.

English

To activate the Turbo setting, press the Turbo

button once.

Move the shaving heads over your skin in circular

movements.

Note: Donot make straight movements.

To deactivate the Turbo setting, press the Turbo

button once.

Using the click-on attachments

Note: The accessories supplied may vary for different products. The box shows the accessories that have been supplied with your appliance.

Removing or attaching the click-on attachments

Make sure the appliance is switched off.

Pull the attachment straight off the appliance.

Note: Do not twist the attachment while you pull it

off the appliance.

Insert the lug of the attachment into the slot in the

top of the appliance. Then press down the

attachment to attach it to the appliance (‘click’).

Using the trimmer attachment (specific types only)

You can use the trimmer attachment to groom your sideburns and moustache.

Make sure the appliance is switched off.

Remove the shaving unit from the appliance.

English

Insert the lug of the trimmer attachment into the

slot in the top of the appliance.

Switch on the appliance.

You can now start trimming.

Clean the attachment after use (see 'Cleaning and

maintenance').

Using the beard styler attachment (specific types only)

Make sure the appliance is switched off.

Insert the lug of the beard styler attachment into

the slot in the top of the appliance. Then press

down the beard styler attachment to attach it to

the appliance (‘click’).

Using the beard styler attachment with comb

You can use the beard styler attachment with the comb attached to style your beard at one fixed setting, but also at different length settings. You can use it also to pre-trim any long hairs before shaving to have a more comfortable shave.

The hair length settings on the beard styler attachment correspond to the remaining hair length after cutting and range from 1 to 5mm.

Slide the comb straight into the guiding grooves on

both sides of the attachment (‘click’).

English

Press the length selector and then push it to the

left or right to select the desired hair length setting.

Switch on the appliance.

You can now start styling your beard by moving

the attachment upwards with gentle pressure

making sure the front of the comb is in full contact

with the skin.

Clean the attachment after use (see 'Cleaning and

maintenance').

Using the beard styler attachment without comb

You can use the beard styler attachment without the comb to contour your beard, moustache, sideburns or neckline to a length of 0.5mm.

Pull the comb off the beard styler attachment.

Note: Grab the comb in the centre to pull it off the

Beard Styler attachment. Do not pull at the sides of

the comb.

Switch on the appliance.

You can now start contouring your beard,

moustache, sideburns or neckline by moving the

styler downwards with gentle pressure while

holding it perpendicular to the skin.

Clean the attachment after use (see 'Cleaning and

maintenance').

English

Cleaning and maintenance

Cleaning the shaver under the tap

Clean the shaver after every shave for optimal performance.

Caution: Be careful with hot water. Always check if the water is not too hot, to prevent burning your hands.

Caution: Never dry the shaving unit with a towel or tissue, as this may damage the shaving heads.

Rinse the shaving unit under a hot tap.

Press the release button to open the shaving unit.

Rinse the shaving head holder under a hot tap for

30 seconds.

Carefully shake off excess water and let the shaving

head holder dry.

Close the shaving head holder ('click').

English

Thorough cleaning method

Switch off the appliance.

Press the release button to open the shaving unit.

Pull the shaving head holder off the bottom part of

the shaving unit.

Turn the retaining rings anticlockwise and remove

them.

Remove the shaving heads from the shaving head

holder. Each shaving head consists of a cutter and

guard.

Note: Do not clean more than one cutter and guard

at a time, since they are all matching sets. If you

accidentally put a cutter in the wrong shaving guard,

it may take several weeks before optimal shaving

performance is restored.

English

Clean the cutter and guard under the tap.

Put the cutter back into the guard.

Place the shaving heads in the shaving head holder.

Note: Make sure that the projections of the shaving

heads fit exactly into the recesses.

Place the retaining rings back onto the shaving

head holder and turn them clockwise ('click').

+ 44 hidden pages