Philips S5320-06 Instruction manual

series S5000

23 24

ENGLISH 4 DANSK 36 DEUTSCH 69

ΕΛΛΗΝΙΚΑ 105

ESPAÑOL 143 SUOMI 179 FRANÇAIS 211 ITALIANO 245 NEDERLANDS 279 NORSK 313 PORTUGUÊS 344 SVENSKA 379 TÜRKÇE 411

S5000 series

ENGLISH

Introduction

Congratulations on your purchase and welcome to

Philips! To fully benet from the support that Philips

offers, register your product at www.philips.com/ welcome.

General description (Fig. 1)

1 Protection cap for nose trimmer attachment

(specic types only)

2 Click-on nose trimmer attachment

(specic types only)

3 Comb for beard styler attachment

(specic types only)

4 Click-on beard styler attachment

(specic types only)

5 Click-on trimmer attachment

(specic types only)

6 Protection cap for shaving unit

(specic types only)

7 Click-on shaving unit 8 On/off button

9 Turbo button (specic types only)

10 Handle 11 Socket for small plug 12 Battery charge indicator with 1 light 13 Battery charge indicator with 3 lights 14 Travel lock symbol 15 Replacement reminder 16 Cleaning reminder 17 Cleaning cartridge for SmartClean system

18 SmartClean system (specic types only)

19 Cap of SmartClean system 20 On/off button 21 Battery symbol 22 Cleaning symbol

ENGLISH 5

23 Replacement symbol 24 Ready symbol 25 Adapter 26 Small plug

27 Pouch (specic types only)

Note: The accessories supplied may vary for different products. The box shows the accessories that have been supplied with your appliance.

Important safety information

Read this important information carefully before you use the appliance and its accessories and save it for future reference. The accessories supplied may vary for different products.

Danger

- Keep the adapter dry.

Warning

- The adapter contains a transformer. Do not cut off the adapter to replace it with another plug, as this causes a hazardous situation.

- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

- Always unplug the shaver before you clean it under the tap.

- Always check the appliance before you use it. Do not use the appliance if it is damaged, as this may cause injury. Always replace a damaged part with one of the original type.

ENGLISH6

Caution

- Never immerse the cleaning system or the charging stand in water and do not rinse it under the tap.

- Never immerse the shaver in water. Do not use the shaver in the bath or in the shower.

- Never use water hotter than 80°C to rinse the shaver.

- Only use this appliance for its intended purpose as shown in the user manual.

- For hygienic reasons, the appliance should only be used by one person.

- Do not use the adapter in or near wall sockets that contain or have contained an electric air freshener to prevent irreparable damage to the adapter

- Never use compressed air, scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the appliance.

- If your shaver comes with a cleaning system,

always use the original Philips cleaning uid

(cartridge or bottle, depending on the type of

cleaning system).

- Always place the cleaning system on a stable, level and horizontal surface to prevent leakage.

- If your cleaning system uses a cleaning cartridge, always make sure that the cartridge compar tment is closed before you use the cleaning system to clean or charge the shaver.

- When the cleaning system is ready for use, do not

move it to prevent leakage of cleaning uid.

- Water may drip from the socket at the bottom of the shaver when you rinse it. This is normal and not dangerous because all electronics are enclosed in a sealed power unit inside the shaver.

ENGLISH 7

Electromagnetic elds (EMF)

- This Philips appliance complies with all applicable standards and regulations regarding exposure to

electromagnetic elds.

General

- This shaver can be safely cleaned under the tap.

- The appliance is suitable for mains voltages ranging from 100 to 240 volts.

- The adapter transforms 100-240 volts to a safe low voltage of less than 24 volts.

- Maximum noise level: Lc = 69dB(A)

The display

Charging

Battery charge indicator with 3 lights

- Charging takes approx. 1 hour

- Quick charge (specic types only): When the appliance is connected to the mains, the lights of the battery charge indicator light up one after the other continuously. When the appliance contains enough energy for one shave, the bottom light of

the battery charge indicator ashes slowly.

- If you leave the appliance connected to the mains, the charging process continues. To indicate

that the appliance is charging, rst the bottom light ashes and then lights up continuously. Then the second light ashes and then lights up

continuously, and so on until the appliance is fully charged.

ENGLISH8

Battery charge indicator with 1 light

- Charging takes approx. 1 hour.

- Quick charge (specic types only): When the appliance does not contain enough energy for one

shave, the battery charge indicator ashes quickly. When the battery charge indicator starts ashing

slowly, the appliance contains enough energy for one shave .

- If you leave the appliance connected to the mains, the charging process continues. To indicate that the appliance is charging, the battery charge

indicator ashes slowly.

Battery fully charged

Note: You can also use this appliance directly from the mains.

Note: When the battery is full, the display switches off automatically after 30 minutes.

When the battery is fully charged, all lights of the battery charge indicator light up continuously.

- Battery charge indicator with 3 lights

- Battery charge indicator with 1 light

ENGLISH 9

Battery low

When the battery is almost empty, the battery

charge indicator ashes orange.

- Battery charge indicator with 3 lights

- Battery charge indicator with 1 light

Remaining battery capacity

Battery charge indicator with 3 lights

- The remaining battery capacity is indicated by the lights of the battery charge indicator that light up continuously.

Cleaning reminder

For optimal shaving performance, we advise you to clean the shaver after every use.

- When you switch off the shaver, the cleaning

reminder ashes to remind you to clean the

shaver.

3 sec.

ENGLISH10

Travel lock

You can lock the shaver when you are going to travel. The travel lock prevents the shaver from being switched on by accident.

Activating the travel lock

1 Press the on/off button for 3 seconds to enter

the travel lock mode.

- While you activate the travel lock, the travel lock symbol lights up continuously. When the travel

lock is activated, the travel lock symbol ashes.

Deactivating the travel lock

1 Press the on/off button for 3 seconds.

- The travel lock symbol ashes and then lights up continuously.

The shaver is now ready for use again.

Replacing shaving heads

For maximum shaving performance, we advise you to replace the shaving heads every two years.

- The appliance is equipped with a replacement reminder which reminds you to replace the shaving heads. The replacement reminder lights up white continuously.

Note: After replacing the shaving heads, you need to reset the replacement reminder by pressing the on/off button for 7 seconds.

ENGLISH 11

Turbo setting (specic types only)

- The appliance is equipped with a Turbo or Turbo+ setting. This setting is intended for quicker and more intense shaving and makes hard-to-reach areas easier to shave.

Activating the Turbo setting

1 To activate the Turbo setting, press the Turbo

button once.

Deactivating the Turbo setting

1 To deactivate the Turbo setting, simply press

the Turbo button once again.

Charging

Charging takes approx. 1 hour.

Note: You can also use this appliance directly from the mains.

Charge the shaver before you use it for the rst

time and when the display indicates that the battery is almost empty.

Charging with the adapter

1 Insert the small plug into the appliance and put

the adapter in the wall socket.

ENGLISH12

Charging in the SmartClean system

(specic types only)

1 Put the small plug in the SmartClean system. 2 Put the adapter in the wall socket. 3 Press down the top cap to be able to place the

shaver in the holder (‘click’).

4 Hold the shaver upside down above the holder.

Make sure the front of the shaver points towards the SmartClean system.

5 Place the shaver in the holder, tilt the shaver

backwards and press down the top cap to connect the shaver (‘click’).

- The battery symbol ashes slowly to indicate the shaver is charging.

Using the shaver

Switching the appliance on and off

1 To switch on the appliance, press the on/off

button once.

2 To switch off the appliance, press the on/off

button once.

- Battery charge indicator with 3 lights: The display lights up for a few seconds to show the remaining battery status.

ENGLISH 13

Shaving

Skin adaptation period

Your rst shaves may not bring you the result you

expect and your skin may even become slightly irritated. This is normal. Your skin and beard need time to adapt to any new shaving system. We advise you to shave regularly (at least 3 times

a week) with this shaver for a period of 3 weeks to

allow your skin to adapt to the new shaver.

Note: You can also use the shaver directly from the mains.

1 Switch on the appliance. 2 Move the shaving heads over your skin in

circular movements.

Note: Do not make straight movements.

3 Clean the shaver after use (see chapter

‘Cleaning and maintenance’).

Turbo setting (specic types only)

The appliance is equipped with a Turbo or Turbo+ setting for easy shaving of hard-to reach areas.

1 Switch on the shaver. 2 Press the Turbo button once to switch on the

Turbo setting if you want to shave hard-toreach areas more quickly.

3 Move the shaving heads over your skin in

circular movements.

Note: Do not make straight movements.

4 To deactivate the Turbo setting simply press

the Turbo button once.

ENGLISH14

Using the click-on attachments

Note: The accessories supplied may vary for different products. The box shows the accessories that have been supplied with your appliance.

Removing or attaching the click-on attachments

1 Make sure the appliance is switched off. 2 Pull the attachment straight off the appliance.

Note: Do not twist the attachment while you pull it off the appliance.

3 Insert the lug of the attachment into the slot

in the top of the appliance. Then press down the attachment to attach it to the appliance (‘click’).

Using the trimmer attachment

You can use the trimmer attachment to groom your sideburns and moustache.

1 Make sure the appliance is switched off. 2 Insert the lug of the attachment into the slot

in the top of the shaver. Then press down the trimmer attachment to attach it to the

appliance (‘click’).

3 Switch on the appliance. 4 You can now start trimming. 5 Clean the attachment after use (see chapter

‘Cleaning and maintenance’).

ENGLISH 15

Using the beard styler attachment

1 Make sure the appliance is switched off. 2 Insert the lug of the attachment into the slot

in the top of the appliance. Then press down

the attachment to attach it to the appliance

(‘click’).

Using the beard styler attachment with comb

You can use the beard styler attachment with the

comb attached to style your beard at one xed

setting, but also at different length settings. You can use it also to pre-trim any long hairs before shaving to have a more comfortable shave. The hair length settings on the beard styler attachment correspond to the remaining hair length after cutting and range from 1 to 5mm.

1 Slide the comb straight into the guiding

grooves on both sides of the attachment

(‘click’).

2 Press the length selector and then push it

to the left or right to select the desired hair

length setting.

3 Switch on the appliance. 4 You can now start styling your beard by

moving the attachment upwards with

gentle pressure making sure the front of

the comb is in full contact with the skin.

5 Clean the attachment after use (see chapter

‘Cleaning and maintenance’).

ENGLISH16

Using the beard styler attachment without comb

You can use the beard styler attachment without the comb to contour your beard, moustache, sideburns or neckline to a length of 0.5mm.

1 Pull the comb off the attachment.

Note: Grab the comb in the centre to pull it off the attachment. Do not pull at the sides of the comb.

2 Switch on the appliance.

3 You can now start contouring your beard,

moustache, sideburns or neckline by moving

the styler downwards with gentle pressure

while holding it perpendicular to the skin.

4 Clean the attachment after use

(see chapter ‘Cleaning and maintenance’).

Using the nose trimmer attachment

You can use the nose trimmer attachment to trim your nose hair. Make sure your nostrils are clean.

1 Insert the lug of the attachment into the slot

in the top of the appliance. Then press down

the attachment to attach it to the appliance

(‘click’).

2 Switch on the appliance. 3 Carefully insert the attachment into one of

your nostrils. Do not insert the attachment more than 0.5cm

into your nostrils.

ENGLISH 17

4 Slowly move the attachment around to remove

all unwanted hairs in your nostrils.

5 Clean the attachment after use

(see chapter ‘Cleaning and maintenance’).

Trimming ear hair

You can use the nose trimmer attachment to trim your ear hair. Make sure your outer ear channels are clean and free from wax.

1 Insert the lug of the attachment into the slot

in the top of the appliance. Then press down

the attachment to attach it to the appliance

(‘click’).

2 Switch on the appliance. 3 Slowly move the attachment along the rim of

the ear to remove hairs that stick out beyond

the rim.

4 Insert the attachment into the outer ear

channel. Do not insert the attachment more than 0.5cm

into your ear channel, as this could damage the eardrum.

5 Slowly turn the attachment around to remove

all unwanted hairs from your outer ear

channel.

6 Clean the attachment after use (see chapter

‘Cleaning and maintenance’).

ENGLISH18

Cleaning and maintenance

Note: The accessories supplied may vary for different products. The box shows the accessories that have been supplied with your appliance.

Cleaning the shaver in the SmartClean

system (specic types only)

Do not tilt the SmartClean system to prevent leakage.

Note: Hold the SmartClean system while you prepare it for use.

Note: If you clean the shaver in the SmartClean system once a week, the SmartClean cartridge will last approximately three months.

Preparing the SmartClean system for use

1 Put the small plug in the back of the

SmartClean system.

2 Put the adapter in the wall socket. 3 Press the button on the side of the SmartClean

system and lift the top part of the SmartClean

system.

4 Pull the seal off the cleaning cartridge.

5 Place the cleaning cartridge in the SmartClean

system.

ENGLISH 19

6 Push the top part of the SmartClean system

back down (‘click’).

Using the SmartClean system

Always make sure to shake excess water off the

shaver before you place it in the SmartClean system.

1 Press down the top cap to be able to place the

shaver in the holder (‘click’).

2 Hold the shaver upside down above the holder.

Make sure the front of the shaver points

towards the SmartClean system.

3 Place the shaver in the holder, tilt the shaver

backwards and press down the top cap to

connect the shaver (‘click’).

- The battery symbol ashes slowly to indicate that the shaver is charging.

ENGLISH20

4 Press the on/off button on the SmartClean

system to start the cleaning program.

- During the cleaning program (which takes approx.

10 minutes), the cleaning symbol ashes.

- When the cleaning program has been completed, the ready symbol lights up continuously.

- The battery symbol lights up continuously to indicate that the shaver is fully charged. This takes approx. 1 hour.

Note: If you press the on/off button of the SmartClean system during the cleaning program, the program aborts.

In this case, the cleaning symbol stops ashing.

Note: If you remove the adapter from the wall socket during the cleaning program, the program aborts.

Note: 30 minutes after the charging phase has been completed, the SmartClean system switches off automatically.

5 To let the shaver dry, you can leave it in the

SmartClean system until your next shave. You can also remove the shaver from the SmartClean system, shake off excess water, open the shaving unit and let the shaver air dry.

Replacing the cartridge of the SmartClean System

Replace the cleaning cartridge when the

replacement symbol ashes orange or when you are no longer satised with the cleaning result.

If you clean the shaver in the SmartClean system once a week, the SmartClean cartridge will last approximately three months.

ENGLISH 21

1 Press the button on the side of the SmartClean

system and lift the top part of the SmartClean system.

2 Take the empty cleaning cartridge from the

SmartClean system and pour any remaining

cleaning uid out of the cleaning cartridge.

You can simply pour the cleaning uid down the sink.

3 Throw away the empty cleaning cartridge. 4 Unpack the new cleaning cartridge and pull the

seal off the cartridge.

5 Place the new cleaning cartridge in the

SmartClean system.

6 Push the top part of the SmartClean system

back down (‘click’).

Cleaning the shaver under the tap

Clean the shaver after every shave for optimal shaving performance.

Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt.

Never dry the shaving unit with a towel or tissue, as this may damage the shaving heads.

ENGLISH22

1 Rinse the shaving unit under a warm tap for

some time.

2 Press the release button and open the shaving

unit.

3 Rinse the shaving head holder under a warm

tap for 30 seconds.

4 Carefully shake off excess water and let the

shaving head holder dry.

5 Close the shaving head holder (‘click’).

Thorough cleaning method

Make sure the appliance is switched off.

1 Press the release button and open the shaving

unit.

2 Pull the shaving head holder off the bottom

part of the shaving unit.

ENGLISH 23

3 Turn the retaining rings anticlockwise and

remove them.

4 Remove the shaving heads from the shaving

head holder. Each shaving head consists of a cutter and guard.

Note: Do not clean more than one cutter and guard at a time, since they are all matching sets. If you accidentally put a cutter in the wrong shaving guard, it may take several weeks before optimal shaving performance is restored.

5 Clean the cutter and guard under the tap.

6 After cleaning, place the cutter back into the

guard.

7 Put the shaving heads back into the shaving

head holder.

ENGLISH24

Note: Make sure the projections of the shaving heads

t exactly into the recesses of the shaving-head holder.

8 Place the retaining rings back onto the shaving

head holder and turn them clockwise.

- Each retaining ring has two recesses and two

projections that t exactly in the projections and

recesses of the shaving head holder.

- Turn the ring clockwise until your hear ‘click’ and

the ring is xed.

Note: Hold the shaving head holder in your hand when you reinsert the shaving heads and reattach the retaining rings. Do not place the shaving head holder on a surface when you do this, as this may cause damage.

ENGLISH 25

9 Reinsert the hinge of the shaving head holder

into the slot of the shaving unit. Close the shaving head holder (‘click’).

Cleaning the click-on attachments

Never dry the trimmer or beard styler attachments with a towel or tissue, as this may damage the trimming teeth.

Cleaning the trimmer attachment

Clean the trimmer attachment every time you have used it.

1 Switch on the appliance with the trimmer

attachment attached.

2 Rinse the trimmer attachment under a hot tap

for some time.

3 After cleaning, switch off the appliance. 4 Carefully shake off excess water and let the

trimmer attachment dry.

Tip: For optimal trimmer performance, lubricate the trimmer teeth with a drop of sewing machine oil every six months.

Cleaning the beard styler attachment

Clean the beard styler attachment every time you have used it.

1 Pull the comb off the beard styler attachment.

ENGLISH26

Note: Grab the comb in the centre to pull it off the attachment. Do not pull at the sides of the comb.

2 Switch on the appliance.

3 Rinse the beard styler attachment and the

comb separately under a hot tap for some

time.

4 After cleaning, switch off the appliance.

5 Carefully shake off excess water and let the

beard styler attachment and comb dry.

Tip: For optimal trimmer performance, lubricate the trimmer teeth with a drop of sewing machine oil every six months.

Cleaning the nose trimmer attachment

Clean the nose trimmer attachment every time you have used it.

1 Make sure the appliance is switched off. 2 Rinse the cutting element of the nose trimming

head with hot water.

3 Switch on the appliance and rinse the cutting

element once more to remove any remaining

hairs. Then switch off the appliance again.

4 Carefully shake off excess water and let the

nose trimmer attachment dry.

Tip: For optimal trimmer performance, lubricate the trimmer teeth with a drop of sewing machine oil every six months.

ENGLISH 27

Storage

Note: The accessories supplied may vary for different products. The box shows the accessories that have been supplied with your appliance.

Note: We advise you to let the appliance and its attachments dry before you put the protection caps on the attachments and store the shaver in the pouch.

- Place the protection cap on the nose trimming head.

- Put the protection cap on the shaving head to protect it from dirt accumulation.

- Store the shaver in the pouch supplied.

Replacement

Replacing the shaving heads

For maximum shaving performance, we advise you to replace the shaving heads every two years.

Replacement reminder

The shaving unit symbol will light up to indicate that the shaving heads need to be replaced. Replace damaged shaving heads immediately. Only replace the shaving heads with original Philips shaving heads

as specied in chapter ‘Ordering accessories’.

ENGLISH28

1 The shaving unit symbol lights up continuously

when you switch off the shaver to indicate that the shaving heads need to be replaced.

2 Press the release button and open the shaving

unit.

3 Pull the shaving head holder off the bottom

part of the shaving unit.

4 Turn the retaining rings anticlockwise and

remove them.

5 Remove the shavings heads from the shaving

head holder and throw them away.

ENGLISH 29

6 Place new shaving heads in the holder.

Note: Make sure the projections of the shaving heads

t exactly into the recesses of the shaving head holder.

7 Place the retaining rings back onto the shaving

heads and turn them clockwise.

- Each retaining ring has two recesses and two

projections that t exactly in the projections and

recesses of the shaving head holder.

- Turn the ring clockwise until your hear ‘click’ and

the ring is xed.

ENGLISH30

Note: Hold te shaving head holder in your hand when you reinsert the shaving heads and reattach the retaining rings. Do not place the shaving head holder on a surface when you do this, as this may cause damage.

8 Reinsert the hinge of the shaving head holder

into the slot of the shaving unit. Close the shaving head holder (‘click’).

7 sec.

9 To reset the replacement reminder, press and

hold the on/off button for approx. 7 seconds.

Ordering accessories

To buy accessories or spare parts, visit www.shop.philips.com/service or go to your Philips dealer. You can also contact the Philips Consumer Care Centre in your country (see the

worldwide guarantee leaet for contact details).

The following parts are available:

- HQ8505 adapter

- SH50 Philips shaving heads

- HQ110 Philips Shaving Head Cleaning Spray

- RQ111 Philips beard styler attachment

- JC301, JC302, JC303, JC304, JC305 cleaning cartridge

Note: Availability of the accessories may differ per country.

+ 413 hidden pages