Philips S5130, S5110, S5015, S5013, S5010 User Manual

S5130
S5110
S5015
S5013
S5011
S5010
S5008

Question?

有疑问?

Contact Philips

请联系飞利浦

1

S5130/04 , S5110/04 , S5015/61, S5013/04 , S5011/04 , S5010/03, S5008/ 04

ENGLISH 6

简体中文 28

6

Introduction

Congratulations on your purchase and welcome to

Philips! To fully benet from the support that Philips

offers, register your product at

www.philips.com/welcome.

General description (Fig. 1)

1 Protection cap for shaving unit
2 Click-on shaving unit
3 On/off button
4 Handle
5 Socket for small plug
6 Adapter
7 Small plug
8 Battery charge indicator
9 Travel lock symbol
10 Replacement reminder

(S5130/04, S5110/04, S5013/04 only)

11 Cleaning reminder

(S5130/04, S5110/04, S5013/04 only)

12 Click-on nose trimmer attachment

(S5015/61 only)

13 Protection cap for nose trimmer attachment

(S5015/61 only)

14 Click-on trimmer attachment

(S5130/04, S5110/04, S5015/61, S5013/04,
S5011/04, S5008/04 only)

Note: The accessories supplied may vary for different
products. The box shows the accessories that have been
supplied with your appliance.

ENGLISH

Important safety information

Read this important information carefully before you
use the appliance and its accessories and save it for
future reference. The accessories supplied may vary
for different products.

Danger

- Keep the adapter dry.

Warning

- The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug,
as this causes a hazardous situation.

- This appliance is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.

- Children should be supervised to ensure that they
do not play with the appliance.

- Always unplug the shaver before you clean it
under the tap.

- Always check the appliance before you use it.
Do not use the appliance if it is damaged, as this
may cause injury. Always replace a damaged part
with one of the original type.

Caution

- Never immerse the cleaning system or the charging
stand in water and do not rinse it under the tap.

- Never immerse the shaver in water. Do not use
the shaver in the bath or in the shower.

-

Never use water hotter than 80°C to rinse the shaver.

- Only use this appliance for its intended purpose as
shown in the user manual.

ENGLISH 7

- For hygienic reasons, the appliance should only be
used by one person.

- Never use compressed air, scouring pads,
abrasive cleaning agents or aggressive liquids such
as petrol or acetone to clean the appliance.

- If your shaver comes with a cleaning system,

always use the original Philips cleaning uid

(cartridge or bottle, depending on the type of
cleaning system).

- Always place the cleaning system on a stable,
level and horizontal surface to prevent leakage.

- If your cleaning system uses a cleaning cartridge,
always make sure that the cartridge compartment
is closed before you use the cleaning system to
clean or charge the shaver.

- When the cleaning system is ready for use,

do not move it to prevent leakage of cleaning uid.

- Water may drip from the socket at the bottom
of the shaver when you rinse it. This is normal
and not dangerous because all electronics are
enclosed in a sealed power unit inside the shaver.

Electromagnetic elds (EMF)

- This Philips appliance complies with all applicable
standards and regulations regarding exposure to

electromagnetic elds.

General

- This shaver can be safely cleaned under the tap.

- The appliance is suitable for mains voltages ranging
from 100 to 240 volts.

- The adapter transforms 100-240 volts to a safe
low voltage of less than 24 volts.

ENGLISH8

The display

Charging

Battery charge indicator

- Charging takes approx. 1 hour (S5130/04,
S5110/04, S5013/04 only) or 8 hours (S5015/61,
S5011/04, S5010/03, S5008/04 only).

- Quick charge (S5130/04, S5110/04, S5013/04
only): When the appliance does not contain
enough energy for one shave, the battery charge

indicator ashes quickly. When the battery charge
indicator starts ashing slowly, the appliance

contains enough energy for one shave .

- If you leave the appliance connected to the mains,
the charging process continues. To indicate that
the appliance is charging, the battery charge

indicator ashes slowly.

Battery fully charged

Note: You can also use this appliance directly from the
mains.

Note: When the battery is full, the display switches off
automatically after 30 minutes.

- When the battery is fully charged, the light of the
battery charge indicator lights up continuously.

Battery low

- When the battery is almost empty, the battery

charge indicator ashes orange.

ENGLISH 9

Cleaning reminder

For optimal shaving performance, we advise you to
clean the shaver after every use.

- When you switch off the shaver, the cleaning

reminder ashes to remind you to clean the

shaver (S5130/04, S5110/04, S5013/04 only).

Travel lock

You can lock the shaver when you are going to
travel. The travel lock prevents the shaver from being
switched on by accident.

Activating the travel lock

1 Press the on/off button for 3 seconds to enter

the travel lock mode.

- While you activate the travel lock, the travel lock
symbol lights up continuously. When the travel

lock is activated, the travel lock symbol ashes.

Deactivating the travel lock

1 Press the on/off button for 3 seconds.

- The travel lock symbol ashes and then lights up
continuously.

The shaver is now ready for use again.

3 sec.

ENGLISH10

Replacing shaving heads

For maximum shaving performance, we advise you
to replace the shaving heads every two years.

- The appliance is equipped with a replacement
reminder (S5130/04, S5110/04, S5013/04 only)
which reminds you to replace the shaving heads.
The replacement reminder lights up white
continuously.

Note: After replacing the shaving heads, you need to
reset the replacement reminder by pressing the on/off
button for 7 seconds.

Charging

Charging takes approx. 1 hour (S5130/04, S5110/04,
S5013/04) or 8 hours (S5015/61, S5011/04,
S5010/03, S5008/04 only).

Note: You can also use this appliance directly from the
mains.

Charge the shaver before you use it for the rst

time and when the display indicates that the battery
is almost empty.

Charging with the adapter

1 Insert the small plug into the appliance and put

the adapter in the wall socket.

ENGLISH 11

Using the shaver

Switching the appliance on and off

1 To switch on the appliance, press the on/off

button once.

2 To switch off the appliance, press the on/off

button once.

Shaving

Skin adaptation period

Your rst shaves may not bring you the result you

expect and your skin may even become slightly
irritated. This is normal. Your skin and beard
need time to adapt to any new shaving system.
We advise you to shave regularly (at least 3 times
a week) with this shaver for a period of 3 weeks to
allow your skin to adapt to the new shaver.

Note: You can also use the shaver directly from the mains.

1 Switch on the appliance.

2 Move the shaving heads over your skin in

circular movements.

Note: Do not make straight movements.

3 Clean the shaver after use

(see chapter ‘Cleaning and maintenance’).

ENGLISH12

Using the click-on attachments

Note: The accessories supplied may vary for different
products. The box shows the accessories that have been
supplied with your appliance.

Removing or attaching the click-on
attachments

1 Make sure the appliance is switched off.

2 Pull the attachment straight off the appliance.

Note: Do not twist the attachment while you pull it off
the appliance.

3 Insert the lug of the attachment into the slot

in the top of the appliance. Then press down
the attachment to attach it to the appliance
(‘click’).

Using the trimmer attachment
(S5130/04, S5110/04, S5015/61, S5013/04,
S5011/04, S5008/04 only)

You can use the trimmer attachment to groom
your sideburns and moustache.

1 Make sure the appliance is switched off.

2 Insert the lug of the attachment into the slot

in the top of the shaver. Then press down
the trimmer attachment to attach it to the
appliance (‘click’).

3 Switch on the appliance.

4 You can now start trimming.

5 Clean the attachment after use

(see chapter ‘Cleaning and maintenance’).

ENGLISH 13

Using the nose trimmer attachment
(S5015/61 only)

You can use the nose trimmer attachment to trim
your nose hair.
Make sure your nostrils are clean.

1 Insert the lug of the attachment into the slot

in the top of the appliance. Then press down
the attachment to attach it to the appliance
(‘click’).

2 Switch on the appliance.

3 Carefully insert the attachment into one of

your nostrils.

Do not insert the attachment more than

0.5cm into your nostrils.

4 Slowly move the attachment around to remove

all unwanted hairs in your nostrils.

5 Clean the attachment after use

(see chapter ‘Cleaning and maintenance’).

Trimming ear hair

You can use the nose trimmer attachment to trim
your ear hair. Make sure your outer ear channels are
clean and free from wax.

1 Insert the lug of the attachment into the slot

in the top of the appliance. Then press down
the attachment to attach it to the appliance
(‘click’).

2 Switch on the appliance.

3 Slowly move the attachment along the rim of

the ear to remove hairs that stick out beyond
the rim.

ENGLISH14

4 Insert the attachment into the outer ear

channel.

Do not insert the attachment more than 0.5cm
into your ear channel, as this could damage the
eardrum.

5 Slowly turn the attachment around to remove

all unwanted hairs from your outer ear
channel.

6 Clean the attachment after use

(see chapter ‘Cleaning and maintenance’).

Cleaning and maintenance

Note: The accessories supplied may vary for different
products. The box shows the accessories that have been
supplied with your appliance.

Cleaning the shaver under the tap

Clean the shaver after every shave for optimal
shaving performance.

Be careful with hot water. Always check if the
water is not too hot, to prevent your hands from
getting burnt.

Never dry the shaving unit with a towel or tissue,
as this may damage the shaving heads.

1 Rinse the shaving unit under a warm tap for

some time.

2 Press the release button and open the shaving

unit.

ENGLISH 15

3 Rinse the shaving head holder under a warm

tap for 30 seconds.

4 Carefully shake off excess water and let the

shaving head holder dry.

5 Close the shaving head holder (‘click’).

Thorough cleaning method

Make sure the appliance is switched off.

1 Press the release button and open the shaving

unit.

2 Pull the shaving head holder off the bottom

part of the shaving unit.

3 Turn the retaining rings anticlockwise and

remove them.

4 Remove the shaving heads from the shaving

head holder. Each shaving head consists of a
cutter and guard.

Note: Do not clean more than one cutter and guard at a
time, since they are all matching sets. If you accidentally
put a cutter in the wrong shaving guard, it may take several
weeks before optimal shaving performance is restored.

ENGLISH16

5 Clean the cutter and guard under the tap.

6 After cleaning, place the cutter back into the

guard.

7 Put the shaving heads back into the shaving

head holder.

Note: Make sure the projections of the shaving heads

t exactly into the recesses of the shaving-head holder.

8 Place the retaining rings back onto the shaving

head holder and turn them clockwise.

ENGLISH 17

- Each retaining ring has two recesses and two

projections that t exactly in the projections and

recesses of the shaving head holder.

- Turn the retaining ring clockwise until your hear

‘click’ and the ring is xed.

Note: Hold the shaving head holder in your hand
when you reinsert the shaving heads and reattach the
retaining rings. Do not place the shaving head holder
on a surface when you do this, as this may cause
damage.

9 Reinsert the hinge of the shaving head holder

into the slot of the shaving unit. Close the
shaving head holder (‘click’).

Cleaning the click-on attachments

Never dry the trimmer attachments with a towel
or tissue, as this may damage the trimming teeth.

Cleaning the trimmer attachment
(S5130/04, S5110/04, S5015/61, S5013/04,
S5011/04, S5008/04 only)

Clean the trimmer attachment every time you have
used it.

ENGLISH18

1 Switch on the appliance with the trimmer

attachment attached.

2 Rinse the trimmer attachment under a hot tap

for some time.

3 After cleaning, switch off the appliance.

4 Carefully shake off excess water and let the

trimmer attachment dry.

Tip: For optimal trimmer performance, lubricate the
trimmer teeth with a drop of sewing machine oil every
six months.

Cleaning the nose trimmer attachment
(S5015/61 only)

Clean the nose trimmer attachment every time you
have used it.

1 Make sure the appliance is switched off.

2 Rinse the cutting element of the nose trimming

head with hot water.

3 Switch on the appliance and rinse the cutting

element once more to remove any remaining
hairs. Then switch off the appliance again.

4 Carefully shake off excess water and let the

nose trimmer attachment dry.

Tip: For optimal trimmer performance, lubricate the
trimmer teeth with a drop of sewing machine oil every
six months.

ENGLISH 19

Storage

Note: The accessories supplied may vary for different
products. The box shows the accessories that have been
supplied with your appliance.

Note: We advise you to let the appliance and its
attachments dry before you put the protection caps on
the attachments and store the shaver in the pouch.

- S5015/61 only: Place the protection cap on the
nose trimming head.

- Put the protection cap on the shaving head to
protect it from dirt accumulation.

Replacement

Replacing the shaving heads

For maximum shaving performance, we advise you
to replace the shaving heads every two years.
Replace damaged shaving heads immediately.
Only replace the shaving heads with original Philips
shaving heads as specied in chapter
‘Ordering accessories’.

Replacement reminder
(S5130/04, S5110/04, S5013/04 only)

The shaving unit symbol will light up to indicate that
the shaving heads need to be replaced.

1

S5130/04, S5110/04, S5013/04 only: The shaving
unit symbol lights up continuously when you
switch off the shaver to indicate that the shaving
heads need to be replaced.

ENGLISH20

2 Press the release button and open the shaving

unit.

3 Pull the shaving head holder off the bottom

part of the shaving unit.

4 Turn the retaining rings anticlockwise and

remove them.

5 Remove the shavings heads from the shaving

head holder and throw them away.

6 Place new shaving heads in the holder.

ENGLISH 21

Note: Make sure the projections of the shaving heads

t exactly into the recesses of the shaving head holder.

7 Place the retaining rings back onto the shaving

heads and turn them clockwise.

- Each retaining ring has two recesses and two

projections that t exactly in the projections and

recesses of the shaving head holder.

- Turn the retaining ring clockwise until your hear

‘click’ and the ring is xed.

Note: Hold the shaving head holder in your hand
when you reinsert the shaving heads and reattach the
retaining rings. Do not place the shaving head holder
on a surface when you do this, as this may cause
damage.

ENGLISH22

8 Reinsert the hinge of the shaving head holder

into the slot of the shaving unit. Close the
shaving head holder (‘click’).

9 S5130/04, S5110/04, S5013/04 only: to reset the

replacement reminder, press and hold the on/
off button for approx. 7 seconds.

Ordering accessories

To buy accessories or spare parts, visit
www.shop.philips.com/service or go to your
Philips dealer. You can also contact the Philips
Consumer Care Centre in your country (see the

worldwide guarantee leaet for contact details).

The following parts are available:

- HQ8505 adapter

- SH50 Philips shaving heads

- HQ110 Philips Shaving Head Cleaning Spray

- RQ111 Philips beard styler attachment

- JC301, JC302, JC303, JC304, JC305 cleaning
cartridge

Note: Availability of the accessories may differ per
country.

ENGLISH 23

Shaving heads

- We advise you to replace your shaving heads
every two years. Always replace the shaving heads
with original SH50 Philips shaving heads.

Recycling

Do not throw away the appliance with the normal
household waste at the end of its life, but hand it in

at an ofcial collection point for recycling. By doing

this, you help to preserve the environment.

Removing the rechargeable shaver battery

Only remove the rechargeable battery when
you discard the shaver. Make sure the battery is
completely empty when you remove it.

Be careful, the battery strips are sharp.

1 Remove the screw in the backpanel with a

screwdriver. Then remove the back panel.

2 Bend the hooks aside and remove the power

unit.

3 Break the snap hooks and remove the front

panel of the power unit.

ENGLISH24

4 Take out the battery holder and cut the

battery tags with a pair of cutting pliers.

Guarantee and support

If you need information or support, please visit
www.philips.com/support or read the separate

worldwide guarantee leaet.

Guarantee restrictions

The shaving heads (cutters and guards) are not
covered by the terms of the international guarantee
because they are subject to wear.

Troubleshooting

This chapter summarises the most common problems
you could encounter with the appliance.
If you are unable to solve the problem with the
information below, visit www.philips.com/support
for a list of frequently asked questions or contact the
Consumer Care Centre in your country.

ENGLISH 25

Problem Possible cause Solution

The shaver does
not shave as well
as it used to.

The shaving
heads are
damaged or
worn.

Replace the shaving heads
(see chapter ‘Replacement’).

Hairs or dirt
obstruct the
shaving heads.

Clean the shaving heads by
following the steps of the
thorough cleaning method
(see chapter ‘Cleaning and
maintenance’).

Clean the shaver thoroughly
before you continue shaving
(see chapter ‘Cleaning and
maintenance’).

The shaver does
not work when I
press the on/off
button.

The
rechargeable
battery is
empty.

Recharge the battery
(see chapter ‘Charging’).

The travel lock
is activated.

Press the on/off button for
3 seconds to deactivate the travel
lock.

The shaving
unit is soiled
or damaged to
such an extent
that the motor
cannot run.

Clean the shaving heads or
replace them (see chapters
‘Cleaning and maintenance’ and
‘Replacement’).

I replaced the
shaving heads, but
the replacement
reminder symbol
is still showing.

You have
not reset the
shaver.

Reset the shaver by pressing
the on/off button for approx.
7 seconds (see chapter
‘Replacement’).

ENGLISH26

Problem Possible cause Solution

A shaving
head symbol
has suddenly
appeared on the
display.

This symbol is
a replacement
reminder.

Replace the shaving heads
(see chapter ‘Replacement’).

The nose
trimmer
attachment pulls
at the hairs.

You move the
appliance too
fast.

Do not move the appliance too
fast.

The nose
trimmer
attachment does
not work.

The cutting
element of the
attachment
is very dirty,
for instance
because some
nasal mucus
has dried inside
the cutting
element.

Clean the cutting element by
rinsing it under the tap with hot
water. Switch on the appliance
and rinse the cutting element
once more to remove any
remaining hairs.

If rinsing the nose trimmer under
the tap does not unblock the
cutting element, then immerse
it in a glass with warm water for
a few minutes. Then switch on
the appliance and rinse it under
the tap.

ENGLISH 27

简体中文28

简介

感谢您的惠顾，欢迎光临飞利浦！
为了您能充分享受飞利浦提供的支持，
请在 www.philips.com/welcome 上注
册您的产品。

基本说明 (图 1)

1 剃须刀头部件保护盖
2 卡入式剃须刀头部件
3 开/关按钮
4 手柄
5 小插头的转换插座
6 适配器
7 小插头
8 电池充电指示灯
9 旅行锁符号
10 更换提示（仅限于 S5130/04

、S5110/04, S5013/04）

11 清洁提示（仅限于 S5130/04

、S5110/04, S5013/04）

12 卡入式鼻毛修剪器附件

（仅限于 S5015/61）

13 鼻毛修剪器附件保护盖

（仅限于 S5015/61）

14

卡入式修剪器附件（仅限于 S5130/04
、S5110/04、S5015/61、S5013/04
、S5011/04、S5008/04）

注意： 随附的附件可能因产品而异。
包装盒将向您展示随附于您产品的附件。

29

重要安全信息

使用产品及其附件之前，请仔细阅读本
重要信息，并妥善保管以供日后参考。
随附的附件可能因产品而异。

危险

- 保持适配器干燥。

- 警告符号注释：禁止用在打开的水龙

头下进行清洗。

警告

- 电源适配器内含有一个变压器。
切勿自行更换插头，否则将导致严重
后果。

- 产品不打算由有肢体、感官或精神能
力缺陷或缺少使用经验和知识的人
（包括儿童）使用，除非有负责他们
安全的人对他们进行与产品使用有关
的监督或指导。

-

请照看好儿童，本产品不能用于玩耍。

- 在自来水龙头下清洗剃须刀之前，
务必拔掉其电源插头。

- 使用前，请务必检查产品。如果产品
已经损坏，请勿再使用，否则可能对
人体造成伤害。务必用原装型号更换
损坏的部件。

简体中文

警告

- 切勿将清洁系统或充电座浸入水中，
也不要在水龙头下冲洗。

- 警告符号注释：禁止用在打开的水龙
头下进行清洗。

- 切勿将剃须刀浸入水中。
请勿在沐浴或淋浴时使用剃须刀。

- 切勿使用温度高于 80°C
的热水冲洗剃须刀。

- 只能将本产品用于用户手册中所示的
原定用途。

- 出于卫生的目的，本产品只能供一个
人使用。

- 切勿使用压缩气体、钢丝绒、研磨性
清洁剂或腐蚀性液体
（例如汽油或丙酮）来清洁产品。

- 如果剃须刀随附清洁系统，应始终使
用原装飞利浦清洁液（滤芯或瓶，
取决于清洁系统类型）。

- 清洁系统必须放在稳定、
平坦的水平表面上，以防漏液。

- 如果清洁系统采用清洁滤芯，
在使用清洁系统进行清洁或为剃须刀充
电之前，应始终确保滤芯仓已关闭。

- 清洁系统准备就绪时，切勿移动，
以免清洁液漏出。

- 冲洗产品时，水可能从剃须刀底部的
插口滴出。这是正常的，而且没有危
险，因为所有的电子线路都密封在剃
须刀内的一个密封壳内。

简体中文30

电磁场 (EMF)

- 本飞利浦产品符合所有有关暴露于电
磁场的适用标准和法规。

概述

- 这款剃须刀可放心在水龙头下清洗。

- 符号注释：适合用在打开的水龙头下

进行清洗。

- 本产品适合在 100 - 240 伏的电源电
压下工作。

- 电源适配器可将 100-240 伏的电压转
换为 24 伏以下的安全低电压。

显示屏

充电

电池充电指示灯

- 充电约需 1 小时（仅限于 S5130/04
、S5110/04、S5013/04）或 8 小
时（仅限于 S5015/61、S5011/04
、S5010/03、S5008/04）。

- 快速充电（仅限于 S5130/04
、S5110/04、S5013/04）：
当产品所含电量不足以完成一次剃须
时，电池充电指示灯将快速闪烁。
当电池充电指示灯开始缓慢闪烁时，
产品所含电量将足以完成一次剃须。

- 如果将产品接通电源，充电过程将继
续。电池充电指示灯缓慢闪烁，
表明产品正在充电。

简体中文 31

电池已完全充满

注意： 您也可以直接插电使用本产品。
注意： 电池充满电后，显示屏会在

30 分钟后自动关闭。

- 电池充满电后，电池充电指示灯将持
续亮起。

电池电量不足

- 当电池的电量几乎耗尽时，
电池充电指示灯会呈橙色闪烁。

清洗提示

为获得更好剃须效果，
我们建议您每次使用之后都要清洁剃须刀。

- 关闭剃须刀时，清洁提示符号闪
烁，提醒您清洁剃须刀（仅限于
S5130/04、S5110/04, S5013/04）。

旅行锁

您可以在携带剃须刀旅行之前将其锁
住。旅行锁可防止剃须刀被意外打开。

启用旅行锁

1 按住开/关按钮 3 秒钟以进入旅行锁

模式。

3 sec.

简体中文32

- 启用旅行锁时，旅行锁符号会持续亮起。
启用旅行锁后，旅行锁符号会闪烁。

解除旅行锁

1 按开/关按钮 3 秒钟。

- 旅行锁符号闪烁，然后持续亮起。

现在可以重新开始使用剃须刀。

更换剃须刀头

为获得更好剃须效果，建议每两年更换
一次剃须刀头。

- 本产品配有更换提示（仅限于
S5130/04、S5110/04, S5013/04），
它会提醒您更换剃须刀头。
更换提示符号会呈白色持续亮起。

注意： 更换剃须刀头后，您需要通过
按开/关按钮 7 秒来重置更换提醒。

充电

充电约需 1 小时
（S5130/04、S5110/04、S5013/04

）
或 8 小时（仅限于 S5015/61、
S5011/04、 S5010/03、S5008/04）。

注意： 您也可以直接插电使用本产品。

简体中文 33

首次使用剃须刀之前，或当显示屏指示
电池电量几乎耗尽时，请先为剃须刀
充电。

使用适配器充电

1 将小插头插入产品，然后将适配器

插入电源插座。

使用剃须刀

打开或关闭产品

1 要打开产品，请按一下开/关按钮。
2 要关闭产品，请按一下开/关按钮。

剃须

皮肤适应期

前几次剃须可能不会带给您预期效果，
并且您的皮肤可能会受到轻度刺激。这
是正常的。您的皮肤和胡须需要时间适
应新的剃须系统。 建议您在 3 周时间
内定期剃须（至少每周 3 次），以便
让您的皮肤适应新的剃须刀。

注意： 您也可以直接插电使用剃须
刀。

简体中文34

1 启动产品。

2

将剃须刀头在您的皮肤上作迂回运动。

注意： 请勿作直线运动。

3 使用后清洁剃须刀（

请参阅“清洁和保养”一章）。

使用卡入式附件

注意： 随附的附件可能因产品而异。
包装盒将向您展示随附于您产品的附件。

拆卸或安装卡入式配件

1 确保产品电源已关闭。
2 将配件竖直抽出产品。

注意： 将配件从产品上抽出时，
不要旋转。

3 将配件的凸缘插入产品顶部的槽

内。然后按下配件以将其安装在产
品上（可听到“咔哒”一声）。

使用修剪器附件（仅限于 S5130/04
、S5110/04、S5015/61、S5013/04
、S5011/04、S5008/04）

您可使用修剪器附件修剪鬓角和须髭。

1 确保产品电源已关闭。

2 将配件的凸缘插入剃须刀顶部的槽

内。然后按下修剪器配件以将其

安

装在产品上（可听到“咔哒”一声）。

简体中文 35

3 启动产品。

4 现在可以开始修剪了。
5 使用后清洁配件（请参阅“清洁和

保养”一章）。

使用鼻毛修剪器附件（仅限于
S5015/61）

您可以使用鼻毛修剪器附件修剪鼻毛。
确保鼻腔是清洁的。

1 将配件的凸缘插入产品顶部的槽

内。然后按下配件以将其安装在产
品上（可听到“咔哒”一声）。

2 启动产品。
3 将附件小心地插入其中一个鼻孔。

附件插入鼻孔的深度不得超过 0.5 厘米。

4 缓缓地来回移动附件，

以剃掉鼻孔中所有多余的毛发。

5 使用后清洁配件

（请参阅“清洁和保养”一章）。

修剪耳毛

您可以使用鼻毛修剪器附件修剪耳毛。
确保外耳道洁净无耳垢。

1 将配件的凸缘插入产品顶部的槽

内。然后按下配件以将其安装在产
品上（可听到“咔哒”一声）。

2 启动产品。

简体中文36

3 缓缓地沿着耳缘移动附件，

以剃掉突出耳缘的毛发。

4 将附件插入外耳道。

附件插入耳道的深度不能超过 0.5 厘
米，否则可能损伤鼓膜。

5 缓缓地转动附件，以剃掉外耳道中

所有多余的毛发。

6 使用后清洁配件（请参阅“清洁和

保养”一章）。

清洁和保养

注意： 随附的附件可能因产品而异。
包装盒将向您展示随附于您产品的附件。

在水龙头下冲洗剃须刀

每次剃须后清洁剃须刀，以获得最佳的
剃须性能。

使用热水时一定要小心。切记先检查水
温是否太高，以防烫手。

不要用毛巾或纸巾擦拭剃须刀头部件，
因为这样可能会损坏剃须刀头。

1

在热水龙头下冲洗剃须刀头部件片刻。

2 按释放按纽，打开剃须刀头部件。

简体中文 37

3 将剃须刀头支架在热水龙头下冲洗

30 秒。

4 小心甩干多余的水，然后使剃须刀

头支架干燥。

5 合上剃须刀头支架（可听到

“咔哒”一声）。

彻底清洁方法

确保产品电源已关闭。

1 按释放按纽，打开剃须刀头部件。

2 将剃须刀头支架从剃须刀头部件的

底部抽离。

3 逆时针旋转固定环并将其取下。

4 从剃须刀头支架上卸下剃须刀头。

每个剃须刀头都包括刀片和网罩。

简体中文38

注意： 不要同时清洁多组刀片和网罩，
因为它们都是相互匹配的。如果不小心
将刀片装到了错误的网罩上，则需要数
周时间才能恢复产品的最佳剃须性能。

5 在水龙头下清洁刀片和网罩。

6 清洁后，将刀片放回网罩中。

7 将剃须刀头装回到剃须刀头支架中。

注意： 确保剃须刀头的凸缘正好装入
剃须刀头支架的凹槽。

8 将固定环放回剃须刀头支架并将其

顺时针旋转。

简体中文 39

- 各固定环均具有两个凹槽和两个凸
缘，正好装入剃须刀头支架的凸缘和
凹槽内。

- 顺时针旋转固定环，直至听到
“咔哒”一声，表明固定环已就位。

注意： 当您重新插入剃须刀头并重新
安装固定环时，请将剃须刀头支架握在
手中。当您执行此操作时，切勿将剃须
刀头支架放在平面上，否则可能会造成
损坏。

9 将剃须刀头支架的铰链重新卡入剃

须刀头部件的槽内。合上剃须刀头
支架（可听到“咔哒”一声）。

简体中文40

清洁卡入式附件

切勿用毛巾或纸巾擦干修剪器附件，
可能会损坏修剪齿。

清洁修剪器附件（仅限于 S5130/04
、S5110/04、S5015/61、S5013/04
、S5011/04、S5008/04）

每次使用后都要清洁修剪器附件。

1 打开装有修剪器附件的产品。
2 在热水龙头下冲洗修剪器附件片刻。
3 清洁完成后，关闭产品。
4 小心地甩干多余的水，

然后使修剪器附件干燥。

提示： 为获得最佳修剪性能，每六个
月用一滴缝纫机油润滑修发器齿。

清洁鼻毛修剪器附件（仅限于
S5015/61）

每次使用后都要清洁鼻毛修剪器附件。

1 确保产品电源已关闭。
2

用热水冲洗鼻毛修剪刀头的修剪部件。

3

打开产品，再次冲洗修剪部件，以清除
任何剩余的毛发。然后再次关闭产品。

4 小心地甩干多余的水份，然后将鼻

毛修剪器附件晾干。

提示： 为获得最佳修剪性能，每六个
月用一滴缝纫机油润滑修发器齿。

简体中文 41

存储

注意： 随附的附件可能因产品而异。
包装盒将向您展示随附于您产品的附件。

注意： 建议您将产品及其配件晾干后
再将保护盖放在配件上，将剃须刀存放
在软袋中。

- 仅限于 S5015/61：将保护盖放在鼻
毛修剪刀头上。

- 将保护盖放在剃须刀头上，以防其积
聚灰尘。

更换

更换剃须刀头

为获得更好剃须效果，建议每两年更换
一次剃须刀头。损坏的剃须刀头应立即
更换。只能使用“订购附件”一章中指
定的飞利浦原装剃须刀头进行更换。

更换提示（仅限于 S5130/04
、S5110/04, S5013/04）

剃须刀头部件符号会亮起，表示需要更
换剃须刀头。

1 仅限于 S5130/04、S5110/04,

S5013/04： 关闭剃须刀时，剃须刀
头部件符号持续亮起，表示需要更换
剃须刀头。

简体中文42

2 按释放按纽，打开剃须刀头部件。

3 将剃须刀头支架从剃须刀头部件的

底部抽离。

4 逆时针旋转固定环并将其取下。

5 从剃须刀头支架上取下剃须刀头并

将其丢弃。

6 将新的剃须刀头放在支架中。

简体中文 43

注意： 确保剃须刀头的凸缘正好装入
剃须刀头支架的凹槽。

7 将固定环放回剃须刀头并将其顺时

针旋转。

- 各固定环均具有两个凹槽和两个凸
缘，正好装入剃须刀头支架的凸缘和
凹槽内。

- 顺时针旋转固定环，直至听到“咔
哒”一声，表明固定环已就位。

注意： 当您重新插入剃须刀头并重新
安装固定环时，请将剃须刀头支架握在
手中。当您执行此操作时，切勿将剃须
刀头支架放在平面上，否则可能会造成
损坏。

简体中文44

8 将剃须刀头支架的铰链重新卡入剃

须刀头部件的槽内。合上剃须刀头
支架（可听到“咔哒”一声）。

9 仅限于 S5130/04、S5110/04,

S5013/04：要重置更换提示，请按
住开/关按钮约 7 秒钟。

订购附件

要购买附件和备件，请访问
www.shop.philips.com/service 或 请联
系飞利浦经销商。您也可以联系您所在
国家/地区的飞利浦客户服务中心
（联系详情，请参阅全球保修卡）。
可选配以下附件：

- HQ8505 适配器

- SH50 飞利浦剃须刀头

- HQ110 飞利浦剃须刀头清洁喷雾剂

- RQ111 飞利浦胡须造型器附件

- JC301、JC302、JC303、JC304

、JC305 清洁滤芯

注意： 各国家/地区的配件可用性可能
会有所不同。

剃须刀头

- 建议您每两年更换一次剃须刀头。
务必使用原装 SH50 飞利浦剃须刀头
进行更换。

简体中文 45

回收

弃置产品时，请不要将其与一般生活垃
圾扔在一起，应将其交给指定的回收中
心，这样做有利于环保。

卸下剃须刀的充电电池

只有在丢弃剃须刀时才可取下充电电
池。请确保在取下电池时电量已完全
耗尽。

注意，电池带非常锋利。

1 用螺丝刀卸下背板中的螺钉。

然后卸下背板。

2 将钩子向外掰，取出电源部件。

3

脱开安全钩，取下电源部件的前面板。

4 取出电池舱，用一把钢丝钳剪下电

池标签。

简体中文46

保修和支持

如果您需要信息或支持，
请访问 www.philips.com/support 或阅
读单独的全球保修卡。

保修条款

由于剃须刀头（刀片和网罩）属于易磨
损物品，因此不在国际保修条款的涵盖
范围之列。

故障种类和处理方法

本章归纳了使用本产品时最常见的一些
问题。如果您无法根据以下信息解决问
题，请访问 www.philips.com/support
查阅常见问题列表，或联系您所在国
家/地区的客户服务中心。

问题 可能的原因 解决方法

剃须刀的剃
须效果没有
以前好。

剃须刀头已损
坏或磨损。

更换剃须刀头（见“更换”一
章）。

毛发或污垢堵
塞了剃须刀
头。

通过执行下列彻底清洁方法中
的步骤来清洁剃须刀头（请参
阅“清洁和保养”一章）。

在继续剃须前彻底清洁剃须刀
（见“清洁和保养”一章）。

按下开/关钮
时，剃须刀
不工作。

充电电池的电
量已耗尽。

给电池充电（见“充电”一
章）。

简体中文 47

问题 可能的原因 解决方法

旅行锁已被激
活。

按住开/关按钮 3 秒钟以禁用旅
行锁。

剃须刀头部件
被污染或损
坏，导致马达
无法运行。

清洁剃须刀头或进行更换
（见“清洁和保养”及“更换”
章节）。

我更换了剃
须刀头，
但仍然显示
更换提醒符
号。

您尚未重置剃
须刀。

按住开/关按钮大约 7 秒钟以重
置剃须刀（见“更换”一章）。

显示屏上突
然出现剃须
刀头符号。

此符号是更换
提醒。

更换剃须刀头（见“更换”一
章）。

鼻毛修剪器
附件拉拔毛
发。

产品移动过
快。

移动本产品时速度不要太快。

鼻毛修剪器
附件不工
作。

附件的修剪部
件非常脏，因
为修剪部件内
部沾有一些干
鼻涕（举个例
子）。

清洁修剪部件：在热水龙头下冲
洗。打开产品，再次冲洗修剪部
件，以清除任何剩余的毛发。

如果在水龙头下冲洗鼻毛修剪器时
未解锁修剪部件，则将其浸入盛有
温水的玻璃杯中几分钟。然后打开
产品，在水龙头下冲洗。

简体中文48

07/04/2015

保留备用

S5130, S5110, S5015, S5013
S5011, S5010, S5008

简体中文 49

4222.002.5760.1