Philips RQ1296, RQ1295, RQ1290, RQ1286, RQ1285 User guide [ml]

...

Always here to help you

RQ1200 series

User manual

ENGLISH 4 DEUTSCH 28

ΕΛΛΗΝΙΚΑ 52

SUOMI 77

RQ1200 series

ENGLISH

Introduction

Congratulations on your purchase and welcome to Philips! To fully benet

from the support that Philips offers, register your product at www.philips.com/welcome. Please read this user manual, as it contains information about the features of this shaver as well as some tips to make shaving easier and more enjoyable.

General description (Fig. 1)

A Shaver 1 Display 2 Shaver on/off button 3 Protection cap 4 RQ12 Shaving unit 5 Trimmer 6 Trimmer on/off slide B RQ111 Beard Styler attachment (RQ1296, RQ1295, RQ1286, RQ1285,

RQ1275, RQ1265 only) 7 Hair length selector 8 Comb of Beard Styler attachment C Foldable charger D Jet Clean System (RQ1296CC, RQ1295CC, RQ1290CC, RQ1286CC,

RQ1285CC, RQ1284CC, RQ1280CC, RQ1275CC, RQ1265CC,

RQ1260CC, RQ1252CC, RQ1251CC, RQ1250CC only) 9 ’Cleaning chamber empty’ symbol 10 Cleaning symbol 11 Drying symbol 12 Jet Clean System on/off button (RQ1008 only: and up/down button

for program selection) 13 Cleaning chamber release button 14 Shaver holder E Cleaning brush

F HQ200 Cleaning uid (RQ1296CC, RQ1295CC, RQ1290CC,

RQ1286CC, RQ1285CC, RQ1284CC, RQ1280CC, RQ1275CC,

RQ1265CC, RQ1260CC, RQ1252CC, RQ1251CC, RQ1250CC only) G Pouch H Adapter

Important

Read this important information carefully before you use the shaver, the Jet Clean system (RQ1296CC, RQ1295CC, RQ1290CC, RQ1286CC, RQ1285CC, RQ1284CC, RQ1280CC, RQ1275CC, RQ1265CC, RQ1260CC, RQ1252CC, RQ1251CC, RQ1250CC only) and the charging

stand. Save this leaet for future reference.

ENGLISH 5

Danger

- Keep the adapter dry.

Warning

- The adapter contains a transformer. Do not cut off the adapter to replace it with another plug, as this causes a hazardous situation.

- The shaver, the Jet Clean system and the charging stand are not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of these appliances by a person responsible for their safety.

- Children should be supervised to ensure that they do not play with the shaver, the Jet Clean system and the charging stand.

- Always unplug the shaver before you clean it under the tap.

Caution

- Never immerse the Jet Clean system or the charging stand in water nor rinse it under the tap.

- Never use water hotter than 80°C to rinse the shaver.

- Do not use the shaver, Jet Clean system, adapter, charging stand or any other part if it is damaged, as this may cause injury. Always replace a damaged adapter, charging stand or part with one of the original type.

- Only use the Jet Clean system with the original HQ200 Jet Clean solution.

- Always place the Jet Clean system on a stable, level and horizontal surface to prevent leakage.

- When the Jet Clean system is ready for use, do not move it to prevent

leakage of cleaning uid.

- The Jet Clean system thoroughly cleans but does not disinfect your shaver, therefore do not share the shaver with others.

- Never use compressed air, scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the appliance.

- Water may leak from the socket at the bottom of the shaver when you rinse it. This is normal and not dangerous because all electronics are enclosed in a sealed power unit inside the shaver.

Compliance with standards

- This shaver is waterproof and complies with the internationally approved safety regulations. It is suitable for use in the bath or shower and for cleaning under the tap. For safety reasons, the shaver can therefore only be used cordlessly.

- The shaver and the Jet Clean system comply with all applicable

standards and regulations regarding exposure to electromagnetic elds.

General

- The adapter is equipped with an automatic voltage selector and is suitable for mains voltages ranging from 100 to 240 volts.

- The adapter transforms 100-240 volts to a safe low voltage of less than 24 volts.

- Maximum noise level: Lc = 69dB(A)

ENGLISH6

The display

Note: Before you use the shaver for the rst time, remove the protective foil from the display.

The various shaver types have different displays, which are shown in the

MINUTES LEFT

gures below.

- RQ1296, RQ1295, RQ1290, RQ1286, RQ1285, RQ1280

- RQ1275, RQ1265, RQ1261, RQ1260

- RQ1273, RQ1252, RQ1251, RQ1250

MINUTES LEFT

Charging

- Charging takes approx. 1 hour.

RQ129x, RQ128x

- When the shaver is charging, the minutes indication ashes.

- The shaving minutes increase until the shaver is fully charged.

- Quick charge: When the shaver contains enough energy for one shave, the display shows 5 minutes in red.

RQ127x, RQ126x, RQ125x

Note: The displays of the various shaver types look different, but the charging lights work in the same way.

- When the shaver is charging, rst the bottom charging light ashes, then the second charging light, and so on until the shaver is fully charged.

- Quick charge: When the shaver contains enough energy for one shave,

the bottom charging light alternately ashes orange and white.

MINUTES LEFT

ENGLISH 7

Battery fully charged

RQ129x, RQ128x

- When the battery is fully charged, the minutes indication lights up continuously. After approx. 30 minutes, the display automatically switches off again.

Note: The shaver is equipped with an intelligent self-learning system that monitors the shaver’s energy consumption and converts the remaining battery capacity into shaving minutes. The energy consumption and therefore the remaining number of shaving minutes depend on your skin and beard type and your shaving behaviour (e.g. the use of shaving gel). If the number of shaving minutes of the fully charged shaver is less than 60 minutes, this is completely normal and does not mean that the battery capacity of the shaver has diminished.

RQ127x, RQ126x, RQ125x

Note: The displays of the various shaver types look different, but the charging lights work in the same way.

- When the battery is fully charged, all charging lights light up continuously. After approx. 30 minutes, the display automatically switches off again.

Battery low

RQ129x, RQ128x

- When the battery is almost empty (when there are only 5 or fewer

shaving minutes left), the minutes indication starts to ash.

- When you switch off the shaver, the shaving minutes continue to ash for a few more seconds. You hear a beep when there are no shaving minutes left.

RQ127x, RQ126x, RQ125x

Note: The displays of the various shaver types look different, but the charging lights work in the same way.

- When the battery is almost empty (when there are only 5 or fewer

shaving minutes left), the bottom charging light ashes orange.

- When you switch off the shaver, the bottom charging light continues to

ash orange for a few seconds.

ENGLISH8

Remaining battery capacity

RQ129x, RQ128x

MINUTES LEFT

- The remaining battery capacity is indicated by the number of shaving minutes shown on the display.

RQ127x, RQ126x, RQ125x

Note: The displays of the various shaver types look different, but the charging lights work in the same way.

- The remaining battery capacity is indicated by the ashing charging lights.

Clean shaver

For optimal shaving performance, we advise you to clean the shaver after

MINUTES LEFT

every use.

Note: The displays of the various shaver types look different, but show the

MINUTES LEFT

same symbol.

- The tap symbol ashes to remind you to clean the shaver.

MINUTES LEFT

Replace shaving unit

For maximum shaving performance, we advise you to replace the shaving unit every two years.

Note: The displays of the various shaver types look different, but show the same symbol.

- To remind you to replace the shaving unit, the appliance is equipped with a replacement reminder which is activated automatically after approx. two years. The replacement reminder is repeated at 9 successive shaves(RQ128x, RQ127x, RQ126x, RQ125x only) or until you reset the shaver.

Travel lock (RQ128x, RQ127x, RQ126x, RQ125x only)

You can lock the shaver when you are going to travel. The travel lock prevents the shaver from being switched on by accident.

Note: The displays of the various shaver types look different, but show the same symbol.

ENGLISH 9

Activating the travel lock

1 Press the on/off button for 3 seconds to enter the travel lock mode.

, RQ128x: The display starts to count down from 3. At 1, the appliance

beeps to indicate that it is locked.

, The lock symbol lights up on the display. After a few seconds it goes out.

Deactivating the travel lock

1 Press the on/off button for 3 seconds.

, The motor starts running to indicate that the travel lock has been

deactivated.

The shaver is now ready for use again.

Note: When you place the shaver in the plugged-in charger or Jet Clean System, the travel lock is automatically deactivated.

Power-saving mode (RQ129x only)

The appliance is equipped with an automatic power-saving mode. When the shaver enters the power-saving mode, the light in the on/off button goes out to save energy.

- When the appliance is switched off but detects movement for 5 minutes (for instance when you are travelling with the shaver in your suitcase), it automatically goes into power-saving mode. This mode prevents the shaver from being switched on by accident.

, The lock symbol ashes on the display to indicate that the appliance

is in power-saving mode.

- To deactivate the power-saving mode, simply press the on/off button.

Blocked shaving heads

MINUTES LEFT

Note: The displays of the various shaver types look different, but show the same symbol.

- If the shaving heads are blocked, the shaving unit symbol, the tap

symbol and the exclamation mark ash. In this case, the motor cannot

run because the shaving heads are soiled or damaged.

- When this happens, you have to clean the shaving unit or replace it.

- The shaving unit symbol, the tap symbol and the exclamation mark

continue to ash until you unblock the shaving heads.

Charging

Charging takes approx. 1 hour. RQ129x, RQ128x, RQ127x, RQ126x: A fully charged shaver has a shaving time of up to 60 minutes.

Note: RQ129x, RQ128x: When the battery is fully charged, the display shows the actual remaining shaving minutes (see section ‘Battery fully charged’ in chapter ‘The display’).

RQ125x: A fully charged shaver has a shaving time of up to 50 minutes.

Charge the shaver before you use it for the rst time and when the display

indicates that the battery is almost empty (see section ‘Battery low’ in chapter ‘The display’).

ENGLISH10

Quick charge

After the shaver has charged for 3 minutes, it contains enough energy for one shave.

Charging in the charger

1 Insert the small plug into the charger.

2 Unfold the charger (‘click’). 3 Put the adapter in the wall socket.

4 Put the shaver in the charger.

, The display shows that the shaver is charging (see chapter ‘The

display’).

Charging in the Jet Clean System (RQ1296CC, RQ1295CC, RQ1290CC, RQ1286CC, RQ1285CC, RQ1284CC, RQ1280CC, RQ1275CC, RQ1265CC, RQ1260CC, RQ1252CC, RQ1251CC, RQ1250CC only)

1 Put the small plug in the Jet Clean System. 2 Put the adapter in the wall socket. 3 Hold the shaver upside down above the holder with the back of the

shaver pointing towards the holder.

Note: The shaver cannot be placed in the Jet Clean System when the protection cap is on the shaving unit.

Note: RQ129x only: when you turn the shaver upside down, the minutes indication on the display is also turned upside down so you can still see to what level the battery is charged.

ENGLISH 11

4 Place the shaver body in the holder behind the two clips (1) and

press it down until it locks into place (2).

, The display shows that the shaver is charging (see section ‘Charging’

in chapter ‘The display’).

Using the shaver

Shaving

Skin adaptation period

Your rst shaves may not bring you the result you expect and your skin

may even become slightly irritated. This is normal. Your skin and beard need time to adapt to any new shaving system. We advise you to shave regularly (at least 3 times a week) for a period of 3 weeks to allow your skin to adapt to the new shaver. During this period, use your new electric shaver exclusively and do not use other shaving

methods. If you use different shaving methods, it is more difcult for your

skin to adapt to the new shaving system.

1 Press the on/off button once to switch on the shaver.

, The display lights up for a few seconds.

2 Move the shaving heads over your skin in circular movements.

- Do not make straight movements.

3 Press the on/off button once to switch off the shaver.

, The display lights up for a few seconds and then shows the remaining

battery capacity.

Wet shaving

You can also use this shaver on a wet face with shaving foam or shaving gel. To shave with shaving foam or shaving gel, follow the steps below:

1 Apply some water to your skin. 2 Apply shaving foam or shaving gel to your skin. 3 Rinse the shaving unit under the tap to ensure that the shaving unit

glides smoothly over your skin.

4 Press the on/off button once to switch on the shaver. 5 Move the shaving heads over your skin in circular movements.

Note: Rinse the shaver under the tap regularly to ensure that it continues to glide smoothly over your skin.

6 Dry your face and thoroughly clean the shaver after use (see chapter

‘Cleaning and maintenance’).

Note: Make sure you rinse all foam or shaving gel off the shaver.

ENGLISH12

Trimming

You can use the trimmer to groom your sideburns and moustache.

1 Pull the shaving unit straight off the shaver.

Note: Do not twist the shaving unit while you pull it off the shaver.

2 Press the on/off button once to switch on the shaver.

, The display lights up for a few seconds.

3 Slide the trimmer slide forwards to slide out the trimmer. 4 You can now start trimming. 5 Slide the trimmer slide backwards to retract the trimmer. 6 Press the on/off button once to switch off the shaver.

, The display lights up for a few seconds and shows the remaining

battery capacity.

7 Insert the lug of the shaving unit into the slot in the top of the shaver

(1). Then press down the shaving unit (2) to attach it to the shaver (‘click’).

Using the Beard Styler attachment (RQ1296, RQ1295, RQ1286, RQ1285, RQ1275, RQ1265 only)

1 Make sure the shaver is switched off. 2 Pull the shaving unit straight off the shaver.

Note: Do not twist the shaving unit while you pull it off the shaver.

ENGLISH 13

3 Insert the lug of the Beard Styler attachment into the slot in the top

of the shaver (1). Then press down the beard styler attachment (2) to attach it to the shaver (‘click’).

Using the Beard Styler attachment with comb

You can use the Beard Styler attachment with the comb attached to style

your beard at one xed setting, but also at different length settings. The

hair length settings on the Beard Styler attachment correspond to the remaining hair length after cutting and range from 1 to 5mm.

1 Slide the comb straight into the guiding grooves on both sides of the

beard styler attachment (‘click’).

2 Press the length selector (1) and then push it to the left or right (2)

to select the desired hair length setting.

3 Press the on/off button on the shaver to switch it on.

4 You can now start styling your beard.

ENGLISH14

Using the Beard Styler attachment without comb

You can use the Beard Styler attachment without the comb to contour your beard, moustache or sideburns.

1 Pull the comb off the Beard Styler attachment.

Note: Grab the comb in the centre to pull it off the Beard Styler attachment. Do not pull at the sides of the comb.

2 Press the on/off button to switch on the shaver.

3 You can now start contouring your beard, moustache, sideburns or

neckline.

Beard styles

Below you nd some examples of beard styles you can create.

- A stubble look

- A full beard

ENGLISH 15

- A moustache

- A goatee

Cleaning and maintenance

Never use scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the shaver, its accessories and the Jet Clean System (RQ1296CC, RQ1295CC, RQ1290CC, RQ1286CC, RQ1285CC, RQ1284CC, RQ1280CC, RQ1275CC, RQ1265CC, RQ1260CC, RQ1252CC, RQ1251CC, RQ1250CC only).

- The best and most hygienic way to clean the shaver is in the Jet Clean System. You can also rinse the shaver under the tap or clean it with the cleaning brush supplied.

- Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt.

- Clean the shaver after every shave for optimal shaving performance.

- You can clean the outside of the shaver with a damp cloth.

- Regular cleaning guarantees better shaving performance.

Cleaning the shaving unit

Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt.

1 Rinse the shaving unit under a hot tap for some time.

ENGLISH16

2 Pull open the three shaving heads one by one.

3 Rinse all three shaving heads and all three hair chambers under a hot

tap for 30 seconds.

Note: You can also brush the shaving heads and hair chambers with the cleaning brush supplied.

Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt.

4 Carefully shake off excess water and leave the shaving heads open to

let the shaving unit dry completely.

Never dry the shaving unit with a towel or tissue, as this may damage the shaving heads.

Cleaning the shaving unit in the Jet Clean System (RQ1296CC, RQ1295CC, RQ1290CC, RQ1286CC, RQ1285CC, RQ1284CC, RQ1280CC, RQ1275CC, RQ1265CC, RQ1260CC, RQ1252CC, RQ1251CC, RQ1250CC only)

The Jet Clean System comes in two types:

- Type RQ1008 has three cleaning programs: the eco program, the auto program and the intensive program. Press the up/down button to select the cleaning program you prefer.

Note: The eco program has a shorter drying time, to save energy. The intensive program is a more thorough cleaning program.

- Type RQ1007 has one automatic cleaning program. When you press the on/off button, the Jet Clean System starts cleaning in the automatic cleaning program.

Preparing the Jet Clean System for use

Fill the cleaning chamber before rst use.

1 Put the small plug in the Jet Clean System. 2 Put the adapter in the wall socket.

, The holder automatically moves to the highest position.

ENGLISH 17

3 Simultaneously press the release buttons on both sides of the

cleaning chamber (1). Then lift the Jet Clean System off the cleaning chamber (2).

, The cleaning chamber remains behind.

4 Unscrew the cap from the bottle with HQ200 cleaning uid.

5 Fill the cleaning chamber with HQ200 cleaning uid to a level

between the two lines.

6 Place the Jet Clean System back onto the cleaning chamber.

Make sure the release buttons click back into place.

Using the Jet Clean System

Note: If you use the shaver with shaving foam or shaving gel, we advise you to rinse it under the hot tap before you clean it in the Jet Clean System. This guarantees an optimal lifetime for the cleaning uid.

1 Hold the shaver upside down above the holder with the back of the

shaver pointing towards the holder.

2 Place the shaver body in the holder behind the two clips (1) and

press it down until it locks into place (2).

, The display shows that the shaver is charging (see chapter ‘The

display’).

3 RQ1008: Press the up/down button to select a cleaning program.

ENGLISH18

4 Press the on/off button on the Jet Clean System to start the cleaning

program.

, The shaver display stops showing the charging indication.

, The cleaning light starts to ash and the shaver is automatically

lowered into the cleaning uid.

, The cleaning light ashes throughout the cleaning program, which

takes a few minutes.

Note: RQ1007: The cleaning program takes 4 to 6 minutes. Note: RQ1008: The auto and eco cleaning programs take 4 to 6 minutes. The

intensive program takes approx. 35 minutes.

, During the rst phase of the cleaning program, the shaver

automatically switches on and off several times and moves up and down.

, During the second phase of the cleaning program, the shaver is

placed in the drying position, indicated by the ashing drying symbol.

This phase takes approx. 2 hours. The shaver stays in this position until the end of the program.

Note: RQ1008: The drying phase takes 1 hour when you have selected the eco program.

, After the cleaning program, the charging indication appears on the

shaver display (see chapter ‘The display’).

Note: If you press the on/off button of the Jet Clean System during the cleaning program, the program aborts. In this case, the cleaning or drying light stops ashing and the holder moves to the highest position.

Note: If you remove the adapter from the wall socket during the cleaning program, the program aborts. The holder remains in its current position. When you put the adapter back into the wall socket, the holder moves to the highest position.

- When the cleaning uid drops below the minimum level, the ‘cleaning chamber empty’ symbol star ts to ash and the holder returns to its

starting position.

- If you use the Jet Clean System to clean your shaver every day, you

need to rell the cleaning chamber approx. every 15 days.

Cleaning the Jet Clean System

Clean the cleaning chamber every 15 days. You can wipe the outside of the Jet Clean System with a damp cloth.

ENGLISH 19

1 Simultaneously press the release buttons on both sides of the Jet

Clean System (1). Then lift the Jet Clean System off the cleaning chamber (2).

, The cleaning chamber remains behind.

2 Pour any remaining cleaning uid out of the cleaning chamber.

You can simply pour the cleaning uid down the sink.

3 Rinse the cleaning chamber under the tap.

The cleaning chamber is not dishwasher-proof.

4 Fill the cleaning chamber with HQ200 cleaning uid to a level

between the two lines.

5 Place the Jet Clean System back onto the cleaning chamber.

Make sure the release buttons click back into place.

ENGLISH20

Extra-thorough cleaning method

Make sure the appliance is switched off.

1 Pull the shaving unit straight off the shaver.

Note: Do not twist the shaving unit while you pull it off the shaver.

2 Pull open the three shaving heads one by one.

3 Press the retainer release tab (1) until the retainer opens (2).

Note: Do not clean more than one cutter and shaving guard at a time, since they are all matching sets. If you accidentally put a cutter in the wrong shaving guard, it may take several weeks before optimal shaving performance is restored.

4 Remove the cutter from the shaving guard.

5 Clean the cutter with the cleaning brush supplied.

ENGLISH 21

6 Clean the inside of the shaving guard.

7 After cleaning, place the cutter back into the shaving guard with the

cutter legs pointing downwards.

8 Press down the retainer over the cutter. 9 Close the shaving heads.

10 Insert the lug of the shaving unit into the slot in the top of the shaver

(1). Then press the shaving unit downwards (2) to attach it to the shaver (‘click’).

Cleaning the trimmer

Clean the trimmer every time you have used it.

1 Slide the trimmer slide forwards to slide out the trimmer.

ENGLISH22

2 Rinse the trimmer under a hot tap for some time. 3 Slide the trimmer slide backwards to retract the trimmer.

Tip: For optimal trimmer performance, lubricate the trimmer teeth with a drop of sewing machine oil every six months.

Cleaning the Beard Styler attachment (RQ1296, RQ1295, RQ1286, RQ1285, RQ1275, RQ1265 only)

Clean the Beard Styler attachment every time you have used it.

1 Pull the comb off the Beard Styler attachment. 2 Rinse the Beard Styler attachment and the comb separately under a

hot tap for some time.

Note: You can also clean the Beard Styler attachment and the comb with the cleaning brush supplied.

3 Lubricate the trimmer teeth with a drop of sewing machine oil every

six months.

Storage

MINUTES LEFT

1 Slide the protection cap onto the shaving unit to prevent damage to

the shaving heads.

2 Store the shaver in the pouch supplied.

Replacement

For maximum shaving performance, we advise you to replace the shaving unit every two years. Only replace the shaving unit with an original RQ12 Philips Shaving unit.

1 The shaving unit symbol ashes (all types) and you hear a beep

(RQ129x, RQ128x only) when you switch off the shaver .

Note: The displays of the different types look different, but show the same symbol.

ENGLISH 23

2 Pull the old shaving unit straight off the shaver.

Note: Do not twist the shaving unit while you pull it off the shaver.

3 Insert the lug of the new RQ12 shaving unit into the slot in the top

of the shaver (1). Then press down the shaving unit (2) to attach it to the shaver (‘click’).

4 RQ128x/RQ127x/RQ126x/RQ125x: To reset the shaver, press and

hold the on/off button for approx. 10 seconds.

Note: If you do not reset the shaver at the rst replacement reminder, it continues to beep (RQ128x only) and show the shaving unit symbol at 8 more shaves or until you reset the shaver.

Note for RQ129x: You do not need to reset the shaver. After 3 shaves, the replacement reminder (ashing shaving unit symbol and beeping) is deactivated automatically.

Ordering accessories

To purchase accessories for this appliance, please visit our online shop at www.shop.philips.com/service. If the online shop is not available in your country, go to your Philips dealer or a Philips service centre. If you

have any difculties obtaining accessories for your appliance, please contact the Philips Consumer Care Centre in your country. You nd its contact details in the worldwide guarantee leaet.

The following parts are available:

- HQ8505 adapter

- RQ12 Philips Shaving Unit

- HQ110 Philips Shaving Head Cleaning Spray

- HQ200 Philips Cleaning Fluid

- RQ111 Beard Styler attachment

ENGLISH24

Shaving heads

- We advise you to replace your shaving heads every two years. Always replace the shaving unit with an original RQ12 Philips Shaving Unit.

Cleaning

- Specic types only: use Jet Clean Solution (HQ200) for regular cleaning of the shaving heads.

Environment

- Do not throw away the appliances with the normal household waste

at the end of their life, but hand them in at an ofcial collection point

for recycling. By doing this, you help to preserve the environment.

- The built-in rechargeable shaver battery contains substances that may pollute the environment. Always remove the battery before you

discard or hand in the shaver at an ofcial collection point. Dispose of the battery at an ofcial collection point for batteries. If you have

trouble removing the battery, you can also take the appliance to a Philips service centre. The staff of this centre will remove the battery for you and will dispose of it in an environmentally safe way.

Removing the rechargeable shaver battery

Only remove the rechargeable battery when you discard the shaver. Make sure the battery is completely empty when you remove it.

Be careful, the battery strips are sharp.

1 Remove the back panel of the shaver with a screwdriver. 2 Remove the rechargeable battery.

Guarantee and support

If you need support or if you have a problem, please visit www.philips.com/support or read the separate worldwide guarantee

leaet.

Guarantee restrictions

The shaving heads (cutters and shaving guards) are not covered by the terms of the international guarantee because they are subject to wear.

Troubleshooting

This chapter summarises the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, visit www.philips.com/support for a list of frequently asked questions or contact the Consumer Care Centre in your country.

Problem Possible cause Solution

ENGLISH 25

The shaver does not shave as well as it used to.

The shaver does not work when I press the on/off button.

The shaving heads are damaged or worn. Replace the shaving unit (see

Long hairs obstruct the shaving heads. Clean the shaving heads by

Specic types only: The Jet Clean System has

not cleaned the shaver properly, because

the cleaning uid in the cleaning chamber is soiled or the cleaning uid level is too low.

The rechargeable battery is empty. Recharge the battery (see

Specic types only: The travel lock

is activated.

The shaving unit is soiled or damaged to such an extent that the motor cannot run. In this case, the shaving unit symbol, the tap

symbol and the exclamation mark ash.

The temperature of the shaver is too high. In this case, the shaver does not work and the

exclamation mark on the display ashes.

chapter ‘Replacement’).

following the steps of the extra-thorough cleaning method (see chapter ‘Cleaning and maintenance’).

Clean the shaver thoroughly before you continue shaving. If

necessary, clean and rell the

cleaning chamber (see chapter ‘Cleaning and maintenance’).

chapter ‘Charging’).

Press the on/off button for 3 seconds to deactivate the travel lock.

Clean the shaving unit or replace it (see chapters ‘Cleaning and maintenance’ and ‘Replacement’).

Switch off the shaver and let it cool down. As soon as the temperature of the shaver has

dropped sufciently, you can

switch on the shaver again.

ENGLISH26

Problem Possible cause Solution

RQ1296CC, RQ1295CC, RQ1290CC, RQ1286CC, RQ1285CC, RQ1284CC, RQ1280CC, RQ1275CC, RQ1265CC, RQ1260CC, RQ1252CC, RQ1251CC, RQ1250CC only: The shaver is not entirely clean after I clean it in the Jet Clean System.

The Jet Clean System does not work when I press the on/off button.

The shaver is not fully charged after I charge it in the charger/Jet Clean System.

The cleaning uid in the cleaning chamber

is soiled.

The cleaning uid level is too low. If the uid volume in the cleaning chamber drops

below the minimum level during the cleaning program, the program aborts.The cleaning light and the ‘cleaning chamber empty’

symbol ash at intervals and the holder

returns to its starting position.

You have used another cleaning uid than the original Philips cleaning uid.

The Jet Clean System is not connected to the mains.

You have not placed the shaver in the Jet Clean System properly, so there is no electrical connection between the Jet Clean System and the shaver.

You have not placed the shaver in the

charger/Jet Clean System (specic types

only) properly.

Empty and rinse the cleaning

chamber and rell it with new cleaning uid.

Rell the cleaning chamber with cleaning uid to a level between

the two lines (see chapter ‘Cleaning and maintenance’).

Only use HQ200 Philips Cleaning Fluid.

Put the small plug in the Jet Clean System and put the adapter in the wall socket.

Press the shaver tightly into the holder to lock it into place.

Make sure you press the shaver until it locks into place.

Problem Possible cause Solution

ENGLISH 27

RQ129x/RQ128x: The shaver is fully charged, but the display shows less than 60 shaving minutes.

RQ1008: The operating time of the Jet Clean System is suddenly shorter or longer than it used to be.

The shaver is equipped with an intelligent self-learning system that monitors the shaver’s energy consumption and converts the remaining battery capacity into shaving minutes. The energy consumption and therefore the remaining number of shaving minutes depend on your skin and beard type and your shaving behaviour (e.g. the use of shaving gel).

You have selected another cleaning program. The Jet Clean System has three cleaning programs: the eco program, the normal program and the intensive program. Each of these programs has a different operating time.

If the number of shaving minutes of the fully charged shaver is less than 60 minutes, this is completely normal and does not mean that the battery capacity of the shaver has diminished.

Press the up/down button on the Jet Clean System to select the cleaning program of your preference (see chapter ‘Cleaning and maintenance’).

DEUTSCH

Einführung

Herzlichen Glückwunsch zu Ihrem Kauf und willkommen bei Philips! Um das Kundendienstangebot von Philips vollständig nutzen zu können, sollten Sie Ihr Produkt unter www.philips.com/welcome registrieren. Lesen Sie diese Bedienungsanleitung sorgfältig durch, da sie nützliche Informationen zu den Funktionen dieses Rasierers sowie Tipps für eine einfache und angenehme Rasur enthält.

Allgemeine Beschreibung (Abb. 1)

A Rasierer 1 Anzeige 2 Ein-/Ausschalter Rasierer 3 Schutzkappe 4 RQ12 Schereinheit 5 Langhaarschneider 6 Ein-/Ausschalter Langhaarschneider B RQ111 Bart-Styler-Aufsatz (nur RQ1296, RQ1295, RQ1286, RQ1285,

RQ1275, RQ1265)

7 Schnittlängenregler 8 Kamm für Bart-Styler-Aufsatz C Zusammenklappbares Ladegerät D Jet Clean System (nur RQ1296CC, RQ1295CC, RQ1290CC,

RQ1286CC, RQ1285CC, RQ1284CC, RQ1280CC, RQ1275CC, RQ1265CC, RQ1260CC, RQ1252CC, RQ1251CC, RQ1250CC)

9 Symbol “Reinigungskammer leer” 10 Reinigungssymbol 11 Trocknungssymbol 12 Ein-/Ausschalter des Jet Clean Systems (nur RQ1008: und Taste nach

oben/unten für Programmauswahl)

13 Entriegelungstaste der Reinigungskammer 14 Halterung für den Rasierer E Reinigungsbürste

F HQ200 Reinigungsüssigkeit (nur RQ1296CC, RQ1295CC,

RQ1290CC, RQ1286CC, RQ1285CC, RQ1284CC, RQ1280CC, RQ1275CC, RQ1265CC, RQ1260CC, RQ1252CC, RQ1251CC, RQ1250CC)

G Tasche H Adapter

Wichtig

Lesen Sie diese wichtigen Informationen aufmerksam durch, bevor Sie den Rasierer, das Jet Clean System (nur RQ1296CC, RQ1295CC, RQ1290CC, RQ1286CC, RQ1285CC, RQ1284CC, RQ1280CC, RQ1275CC, RQ1265CC, RQ1260CC, RQ1252CC, RQ1251CC, RQ1250CC) und die Ladestation verwenden. Bewahren Sie dieses Merkblatt zur späteren Verwendung auf.

DEUTSCH 29

Gefahr

- Halten Sie den Adapter trocken.

Warnhinweis

- Der Adapter enthält einen Transformator. Ersetzen Sie den Adapter keinesfalls durch einen anderen Stecker, da dies eine Gefährdungssituation darstellt.

- Der Rasierer, das Jet Clean System und die Ladestation sind für Benutzer (einschl. Kinder) mit eingeschränkten physischen, sensorischen oder psychischen Fähigkeiten bzw. ohne jegliche Erfahrung oder Vorwissen nur dann geeignet, wenn eine angemessene Aufsicht oder ausführliche Anleitung zur Benutzung der Geräte durch eine verantwortliche Person sichergestellt ist.

- Achten Sie darauf, dass Kinder nicht mit dem Rasierer, dem Jet Clean System und der Ladestation spielen.

- Ziehen Sie stets das Netzteil aus der Steckdose, bevor Sie den Rasierer

unter ießendem Wasser reinigen.

Achtung

- Tauchen Sie das Jet Clean System und die Ladestation niemals in

Wasser. Spülen Sie sie auch nicht unter ießendem Wasser ab.

- Das Wasser zur Reinigung des Rasierers darf nicht heißer als 80°C sein.

- Benutzen Sie den Rasierer, das Jet Clean System, den Adapter, die Ladestation oder andere Teile nicht, wenn Beschädigungen erkennbar sind, da dies zu Verletzungen führen kann. Ersetzen Sie den Adapter, die Ladestation und sonstige Teile im Falle einer Beschädigung nur durch Originalteile.

- Verwenden Sie das Jet Clean System nur mit der Jet Clean OriginalLösung (HQ200).

- Stellen Sie das Jet Clean System stets auf eine stabile, ebene und waagerechte Unterlage, um Auslaufen von Flüssigkeit zu vermeiden.

- Wenn das Jet Clean System betriebsbereit ist, darf es nicht bewegt

werden, damit keine Reinigungsüssigkeit ausläuft.

- Das Jet Clean System reinigt Ihren Rasierer gründlich, desinzier t ihn jedoch nicht. Deshalb sollten Sie Ihren Rasierer nicht gemeinsam mit anderen Personen verwenden.

- Benutzen Sie zum Reinigen des Geräts keine Druckluft, Scheuerschwämme und -mittel oder aggressive Flüssigkeiten wie Benzin oder Azeton.

- Möglicherweise tritt beim Abspülen des Geräts Wasser aus der Buchse unten am Rasierer aus. Das ist normal und völlig ungefährlich, da die gesamte Elektronik im Inneren des Rasierers versiegelt ist.

Normerfüllung

- Dieser Rasierer ist wasserdicht und entspricht den internationalen Sicherheitsvorschriften. Er ist zum Gebrauch in der Badewanne oder

Dusche geeignet und lässt sich unter ießendem Wasser reinigen. Aus

Sicherheitsgründen kann der Rasierer daher nur kabellos verwendet werden.

- Der Rasierer und das Jet Clean System erfüllen sämtliche Normen und Vorschriften bezüglich Kontakt mit elektromagnetischen Feldern.

DEUTSCH30

Allgemeines

- Der Adapter hat eine automatische Spannungsanpassung und eignet sich für Netzspannungen von 100 bis 240 Volt.

- Der Adapter wandelt Netzspannungen von 100 bis 240 Volt in eine sichere Betriebsspannung von unter 24 Volt um.

- Maximaler Geräuschpegel: Lc = 69 dB (A)

Das Display

MINUTES LEFT

Hinweis: Entfernen Sie vor dem ersten Gebrauch des Rasierers die Schutzfolie vom Display.

Die verschiedenen Rasierertypen haben verschiedene Displays, wie unten angegeben.

- RQ1296, RQ1295, RQ1290, RQ1286, RQ1285, RQ1280

- RQ1275, RQ1265, RQ1261, RQ1260

- RQ1273, RQ1252, RQ1251, RQ1250

MINUTES LEFT

Laden

- Der Ladevorgang dauert ca. 1 Stunde.

RQ129x, RQ128x

- Die Minutenanzeige blinkt während des Ladevorgangs.

- Die in Minuten angegebene Rasierzeit verlängert sich, bis der Rasierer vollständig aufgeladen ist.

- Schnellladung: Wenn der Rasierer über ausreichende Akkukapazität für eine Rasur verfügt, zeigt das Display 5 Minuten in Rot an.

RQ127x, RQ126x, RQ125x

Hinweis: Die Displays der verschiedenen Rasierertypen sehen zwar unterschiedlich aus, die Ladeanzeigen funktionieren jedoch auf die gleiche Weise.

+ 71 hidden pages