PHILIPS RI 9827 User Manual

The manufacturer reserves the right to change the features of the product without prior notice.
Le producteur se réserve le droit d“apporter toutes modifications sans préavis.
Type SUP-032BR Cod.15002231 Rev.00 del 15-12-09
Operation and maintenance manual
Before using the machine, please read the attached operating instructions.
Carefully read the safety rules.
Veuillez lire attentivement le mode d'emploi
(notamment les consignes de sécurité) avant d'utiliser l'appareil.
FOR HOUSEHOLD USE ONLY
USAGE DOMESTIQUE SEULEMENT
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed, including the following:
1.
Read all instructions.
2.
Do not touch hot surfaces. Use handles or knobs.
3.
To protect against fire, electric shock and injury to persons do not immerse cord, plugs, or appliance in water or other liquid.
4.
Close supervision is necessary when the appliance is used by or near children.
5.
Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts, and before cleaning the appliance.
6.
Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or adjustment.
7.
The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electric shock or injury to persons.
8.
Do not use outdoors.
9.
Do not let cord hang over edge of table or counter, or touch hot surfaces.
10.
Do not place on or near a hot gas or electric burner, or in a heated oven.
11.
Always attach plug to appliance first, then plug cord into wall outlet. To disconnect, turn any control to “off”, then remove plug from wall outlet.
12.
Do not use appliance for other than intended use.
13.
Save these instructions.
SAVE THESE INSTRUCTIONS
CAUTION
This appliance is for household use only. Any servicing, other than cleaning and user maintenance, should be performed by an authorized service center. Do not immerse machine in water. To reduce the risk of fire or electric shock, do not disassemble the machine. There are no parts inside the machine serviceable by the user. Repair should be done by authorized service personnel only. 1 Check voltage to be sure that the voltage indicated on the nameplate
corresponds with your voltage.
2 Never use warm or hot water to fill the water tank. Use cold water only. 3 Keep your hands and the cord away from hot parts of the appliance during
operation.
4 Never clean with scrubbing powders or harsh cleaners. Simply use a soft
cloth dampened with water.
5 For optimal taste of your coffee, use purified or bottled water. Periodic
descaling is still recommended every 2-3 months.
6 Do not use flavored or caramelized coffee.
INSTRUCTIONS FOR THE POWER
SUPPLY CORD
A.
A short power-supply cord (or detachable power-supply cord) is to be provided to reduce risks resulting from becoming entangled in or tripping over a longer cord.
B.
Longer detachable power-supply cords or extension cords are available and may used if care is exercised in their use.
C.
If a long detachable power-supply cord or extension cord is used,
1.
The marked electrical rating of the detachable power-supply cord or extension cord should be at least as great as the electrical rating of the appliance
2.
If the appliance is of the grounded type, the extension cord should be a grounding-type 3-wire cord, and
3. The longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over.
2
CONTENTS
GENERAL INFORMATION ...................................................................................................................................... 3
TECHNICAL DATA .................................................................................................................................................. 3
APPLIANCE ............................................................................................................................................................4
ACCESSORIES .......................................................................................................................................................4
INSTALLATION ....................................................................................................................................................... 5
STARTING THE MACHINE........................................................................................................................................... 5
SETTING THE LANGUAGE ..........................................................................................................................................6
SETTING THE WATER HARDNESS ................................................................................................................................ 6
FIRST USE - USE AFTER A LONG PERIOD OF INACTIVITY .................................................................................................. 7
INTENZA WATER FILTER ............................................................................................................................................ 8
CONTROL PANEL ................................................................................................................................................... 9
ADJUSTMENTS .................................................................................................................................................... 10
AROMA OPTI-DOSE (ADJUSTS THE COFFEE DOSE PER CUP) ..........................................................................................10
COFFEE STRENGTH ...............................................................................................................................................10
DRIP TRAY HEIGHT ADJUSTMENT .............................................................................................................................. 11
SAECO ADAPTING SYSTEM ...................................................................................................................................... 11
COFFEE GRINDER ADJUSTMENT ............................................................................................................................... 12
BEVERAGE DISPENSING ....................................................................................................................................13
BREWING WITH WHOLE BEANS ................................................................................................................................13
BREWING WITH PRE-GROUND COFFEE ......................................................................................................................14
HOT WATER DISPENSING ........................................................................................................................................ 15
DISPENSING STEAM ..............................................................................................................................................16
MAKING CAPPUCCINO ............................................................................................................................................ 17
MILK ISLAND (OPTIONAL) ........................................................................................................................................ 18
BEVERAGE SETTINGS ........................................................................................................................................ 19
QUICK PROGRAMMING ...........................................................................................................................................19
PROGRAMMING FROM THEBEVERAGE SETTINGSMENU ..............................................................................................19
PROGRAMMING THE MACHINE ......................................................................................................................... 21
MACHINE SETTINGS ..............................................................................................................................................22
LANGUAGE MENU WATER HARDNESS MENU ACOUSTIC ALARM MENU FILTER ALARM MENU RINSE MENU CUP WARMER MENU CLOCK SETTING MENU
MAINTENANCE .....................................................................................................................................................23
WATER FILTER MENU DESCALING MENU BREW GROUP WASHING
ENERGY SAVING (STAND-BY) ............................................................................................................................... 24
TURN OFF DELAY TIMER SETTING
SPECIAL FUNCTIONS .............................................................................................................................................24
MAINTENANCE ....................................................................................................................................................25
DESCALING CYCLE ................................................................................................................................................25
BREW GROUP WASHING ......................................................................................................................................... 28
CLEANING AND MAINTENANCE ......................................................................................................................... 29
MAINTENANCE DURING OPERATION ...........................................................................................................................29
GENERAL MACHINE CLEANING .................................................................................................................................29
CLEANING THE BREW GROUP. ................................................................................................................................. 30
ERROR CODES .................................................................................................................................................... 31
TROUBLESHOOTING ..........................................................................................................................................32
SAFETY RULES ....................................................................................................................................................33
3
This coffee machine is made for brewing espresso coffee using coffee beans, and it is equipped with a device to dispense steam and hot water. The machine is designed for domestic use only, and is not suitable for heavy or professional use.
Warning: no liability is assumed for any damage caused by:
• incorrect use not in accordance with the intended uses;
• repairs not carried out by authorized customer service centers;
• tampering with the power cord;
• tampering with any part of the machine;
• the use of non-original spare parts and accessories;
• failure to descale the machine or use at temperatures below 0°C (32°F)
IN THESE CASES, THE WARRANTY IS NOT VALID.
Keep these operating instructions in a safe place and make them available to anyone else who may use the coffee machine. For further information or in case of problems, please refer to an authorized service
center. For Saeco customer service, call 1-800-933-7876 in the U.S., or 1-514-385-5551 in Canada.
THE WARNING TRIANGLE INDICATES ALL IMPORTANT INSTRUCTIONS FOR THE USER’S SAFETY. PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY TO PREVENT SERIOUS INJURIES!
HOW TO USE THESE OPERATING INSTRUCTIONS.
GENERAL INFORMATION
TECHNICAL DATA
Nominal voltage
See label on the appliance
Power rating
See label on the appliance
Power supply
See label on the appliance
Shell material
ABS - Thermoplastic
Size (w x h x d)
313 x 372 x 426 mm - 12.60 x 14.57 x 15.75 in
Weight
9 Kg - 19.8 lbs
Cord length
1200 mm - 47.24 in
Control panel
Front
Water tank
1.7 liters - 57.5 oz (removable)
Coffee bean hopper capacity
250 grams - 8.9 oz of coffee beans
Pump pressure
15 bar
Boiler
Stainless steel
Coffee grinder
Ceramic
Quantity of ground coffee
7 - 10.5 grams / 0.25 - 0.37 oz.
Dregdrawer capacity
14 portions
Safety devices
Boiler pressure safety valve – Double safety thermostat.
Subject to engineering and manufacturing changes due to technological developments.
TECHNICAL DATA
4
Pre-ground bypass doser
ACCESSORIES
Intenza water fi lter
Water hardness test
strip
APPLIANCE
Power cord
Brew group
Dregdrawer
Socket for power cord
Coffee bean hopper
Power button
Service door
Coffee bean hopper lid
Drip tray
Control panel
SBS dial
Dispensing head
Drip tray + grill
Hot water / steam wand
Water tank
Hot water / steam knob
Milk Island connection
Cup warming surface
Lubricant for the
brew group
Pre-ground coffee
measuring scoop and
grinder adjustment key
5
1 2 3
4
7
65
INSTALLATION
Insert the plug into the socket
located on the back of the
machine and insert the other end
into a power outlet with suitable
current.
Place a container beneath the hot
water/steam wand.
Remove the coffee bean hopper
lid.
Fill the hopper with coffee beans.
Close the lid pushing it down completely.
Remove the water tank.
Install the water fi lter as
recommended on page 8.
Press the main power button to
the “ON” position.
Make sure the power button is not pressed and the machine is turned off. Check the machine features on the label on the bottom of the appliance.
Fill the tank with fresh drinking water. Do not exceed the “max” level indicated on the water tank.
Once fi lled, place the tank back
into the machine.
STARTING THE MACHINE
The machine will automatically prime the water circuit. The machine is now ready for use.
Water may not dispense into the container when the machine is
self-priming. This should be considered normal.
6
4
1 2 3
65
1
2
1 2 3 4
A
B
C
INSTALLATION
SETTING THE LANGUAGE
When the machine is switched on for the fi rst time, it requires the selection of the desired language. This allows you to adjust the parameters of the beverages to the typical parameters of the country where the machine is used. This is why some languages are differentiated also by country.
Select the desired language by
navigating the click wheel with
your fi nger.
When the desired language is displayed, press
.
The machine starts and displays all the messages in the selected language.
2.1 language English
2.1 language English
Wait until the machine completes the warming phase.
The machine is now ready to
brew.
Once the warming phase is
completed, a small quantity of
water is dispensed. Wait for
this rinsing to be completed
automatically. Refer to page 22 to
enable/disable the rinsing function.
warming up
- +
medium aroma
espresso coffee 08:33
rinse cycle please wait
self-diagnosis
Immerse the water hardness test strip in water for 1 second.
Check the water hardness value and set:
- the machine water hardness level (page 22);
- the Intenza Aroma System (page 8).
SETTING THE WATER HARDNESS
Intenza Aroma System
Machine water hardness setting
The test strip can only be used for one measurement.
7
1
5
2
4
7
6
8
9
3
1.
2.
FIRST USE - USE AFTER A LONG PERIOD OF INACTIVITY
These operations ensure an optimum brewing and must be performed:
1) At fi rst start-up
2) When the machine remains inactive for a long time (more than 2 weeks).
Fill the tank with fresh drinking water. Do not exceed the MAX level indicated on the water tank.
Then place the water tank back.
Select the function by pressing the
button until the pre-ground
coffee option appears. Press the button twice WITHOUT adding pre-ground coffee.
pre-ground
espresso coffee 08:33
Place a container under the hot water wand.
Adjust the drip tray (see page 11)
and place a cup under the dispensing spout.
At the end of the dispensing phase, empty the cup. Repeat the operations from step 2 for 3 times. Then continue with step 5.
Press the
button to select the
hot water function.
Turn the knob to the position to start dispensing water.
Dispense water until the container is full.
To stop dispensing, turn the knob
until it reaches the off position (
). Empty the container and repeat the operations from step 5 until the tank is completely empty. The machine is ready.
selected
hot water
8
5 6
7 8 9
1
3
2
4
Insert the fi lter in the empty tank.
The reference mark and the
groove must match. Push fi rmly
until it is completely inserted.
Select “water fi lter” and press
again.
When the machine has fi nished, turn the knob until it is in the rest position ( ). Press a few times until the “exit” message is displayed. Then press
. The machine is now ready for use.
NOTE: if the Intenza water fi lter is not used, insert the small white fi lter previously removed (see step 1)
into the tank.
Press . Select “maintenance” and press the button.
Select “activate fi lter” and press the
button.
Turn the knob to the
position.
Water dispensing begins.
3 maintenance
3.1 water filter 3.1.3 activate filter execute now
INTENZA WATER FILTER
To improve the quality of the water you use, and to extend the life of your machine at the same time, it is recommended that you install the water fi lter. After installation, select the water fi lter function under the maintenance menu (see page 21). By setting the water fi lter status to ON, the machine informs the user when the fi lter must be replaced.
Remove the water fi lter from its packaging, immerse it vertically (with the opening facing upwards) in
cold water and gently press its sides so as to let the air bubbles out.
Remove the small white fi lter from
the tank and store it in a dry place sheltered from dust.
Fill the tank with fresh drinking water and re-insert it into the machine.
Set the Intenza Aroma System: A = Soft water B = Medium water (standard) C = Hard water
Place a container beneath the hot
water/steam wand.
INSTALLATION
1.
1.
2.
2.
2.
3.
1.
9
• Press the button twice to make 2 cups.
This operation can be performed up until the grinding of the fi rst cup is complete.
Press twice
CONTROL PANEL
Access the
programming menu
Click wheel
Selects the aroma
(amount of coffee ground
per cup) or selects pre-
ground coffee
Steam button
Brew button
Hot water button
• To brew 2 cups, the machine dispenses the fi rst coffee and briefl y interrupts dispensing in order to grind
the second serving of coffee.
Coffee dispensing is then restarted and completed.
strong aroma
espresso coffee 08:33
selected
espresso coffee
selected
double espresso
10
ME DIUM
CO F FEE
STR ONG CO F FEE
MI L D
CO F FEE
SBS adjusts the fullness of the brewed coffee. The coffee may even be adjusted while brewing. This adjustment has an immediate effect on the selected type of brewing.
COFFEE STRENGTH
SB S – SAECO BRE W I NG SYSTEM
The SBS dial has been carefully designed to give your coffee the fullness and intensity you desire. Simply turn the dial, and you will notice that the coffee brewed will adjust to the setting selected.
It is possible to choose three aroma options (strong, medium and mild) by pressing the button. These indicate the quantity of coffee the machine grinds for each beverage. This button is
also used to select the pre-ground coffee function.
AROMA OPTI-DOSE (ADJUSTS THE COFFEE DOSE PER CUP)
SELECT THE AMOUNT OF COFFEE TO BE GROUND BEFORE DISPENSING THE BEVERAGE.
strong aroma
espresso coffee 08:33
medium aroma
espresso coffee 08:33
mild aroma
espresso coffee 08:33
pre-ground
espresso coffee 08:33
ADJUSTMENTS
11
SAECO ADAPTING SYSTEM
Coffee is a natural product and its characteristics may change according to its origin, blend and roast. The Saeco coffee machine is equipped with a self-adjusting system that allows the use of all types of coffee beans available on the market (not including fl avored or carmelized).
• The machine automatically adjusts itself in order to optimize the extraction of the coffee, ensuring perfect
compression of the beans to obtain a creamy espresso coffee that is able to release all the aromas,
regardless of the type of coffee used.
• The optimization process is a learning process that requires the brewing of a certain number of coffees to
allow the machine to adjust the compactness of the ground coffee.
• Attention should be given to special blends, which require grinder adjustments in order to optimize the
extraction of the coffee (see page 12).
To raise the drip tray, press lightly on the lower part of
the button. To lower the drip tray, press lightly on the upper part of the button. When the desired height is reached, release the button.
DRIP TRAY HEIGHT ADJUSTMENT
Adjust the drip tray to the appropriate cup size before selecting the beverage.
12
The machine enables a slight adjustment of the coffee grinder. Coffee may be ground according to your own
tastes.
The adjustment must be performed using the small pin located inside the coffee bean hopper.
This must be pressed down and turned using the supplied grinder adjustment key only.
Press and turn the pin one notch at a time.
You must brew 2-3 coffees before you will taste a difference.
The references located inside the bean hopper indicate the grind
setting.
COFFEE GRINDER ADJUSTMENT
FI N E G RINDME DIUM GRI N DCO A RSE GRIN D
ADJUSTMENTS
13
3
4 5
1 2
COFFEE BREWING CAN BE STOPPED AT ANY TIME BY PRESSING THE BUTTON AGAIN.
THE STEAM WAND MAY REACH HIGH TEMPERATURES: DANGER OF SCALDING. DO NOT TOUCH IT WITH BARE HANDS.
Check that all the containers are clean. To carry out this operation, follow the instructions in the “Cleaning and Maintenance” section (see page 29).
To brew 2 cups, the machine dispenses the fi rst coffee and briefl y stops dispensing in order to grind the
second serving of coffee. Coffee dispensing is then restarted and completed.
BREWING WITH WHOLE BEANS
If desired, select the quantity of coffee to be ground by pressing the
button one or more times.
Press the
button: once for
1 cup and twice for 2 cups. The
machine begins dispensing the selected beverage.
BEVERAGE DISPENSING
This procedure shows how to brew an espresso. To brew another type of coffee, select it by navigating the click wheel with your fi nger. Use appropriate espresso or coffee cups so that the coffee will not overfl ow.
The machine stops dispensing automatically based on the quantity determined by the manufacturer. It is possible to customize this quantity (see page 19).
Select the desired beverage by
navigating the click wheel with
your fi nger.
Adjust the drip tray according to
the the height of the cup(s).
Place one cup if you want one coffee only. Place two cups if you want two coffees.
strong aroma
espresso coffee 08:33
strong aroma
espresso coffee 08:33
strong aroma
espresso coffee 08:33
14
4
1 2
5
3
BREWING WITH PRE-GROUND COFFEE
The machine allows you to use pre-ground and decaffeinated coffee.
Pre-ground coffee must be scooped into the bypass doser next to the coffee bean hopper. Only use coffee that is ground specifi cally for espresso machines and never coffee beans or instant coffee.
WARNING: ONLY PUT PRE-GROUND COFFEE INTO THE BYPASS DOSER WHEN YOU WISH TO BREW THIS TYPE OF BEVERAGE.
ONLY INSERT ONE SCOOP OF GROUND COFFEE AT A TIME. TWO CUPS OF COFFEE CANNOT BE DISPENSED AT THE SAME TIME.
Select the function by pressing the
button until the pre-ground
option appears. Press the
button to confi rm.
Note:
If brewing does not start within 30 seconds from the appearance of the message (3), the machine will
return to the main menu and discard any pre-ground coffee into the dregdrawer.
If no pre-ground coffee is poured into the bypass doser, only water will be dispensed.
If the dose is excessive or if 2 or more scoops of coffee are inserted, the machine will not brew the beverage, and the coffee in the bypass doser will be discarded into the dregdrawer.
The preparation of an espresso using pre-ground coffee is shown in the example given below. The
customized option of using pre-ground coffee is shown on the display.
Select the desired beverage by
navigating the click wheel with
your fi nger.
Press the button to start brewing.
Pour one scoop of ground coffee
into the bypass doser using the
measuring scoop provided.
A message reminds the user to insert ground coffee into the
bypass doser.
strong aroma
espresso coffee 08:33
pre-ground
espresso coffee 08:33
brewing in progress
please wait
insert ground coffee
and press ok
BEVERAGE DISPENSING
1.
2.
15
1 2 3
5 6
7
4
HOT WATER DISPENSING
DISPENSING MAY BE PRECEDED BY SHORT SPURTS OF HOT WATER AND SCALDING IS POSSIBLE. THE HOT WATER/STEAM WAND MAY REACH HIGH TEMPERATURES: DO NOT TOUCH IT WITH BARE HANDS. USE THE APPROPRIATE HANDLE ONLY.
Press the
button.
Place a container beneath the hot
water / steam wand.
Turn the knob to the
position.
Wait until the machine has
dispensed the desired quantity of
water.
When the machine has dispensed
the desired quantity, turn the knob
until it is in the rest position (
).
To dispense another cup of hot water, repeat this operation.
The display shows “brewing in
progress... hot water”.
selected
hot water
brewing in progress
hot water
16
1 2 3
5
6
7
4
DISPENSING STEAM
Press the button.
Place a container with the
beverage to be frothed beneath
the hot water/steam wand.
Turn the knob to the
position.
Heat the beverage by gently
swirling the container while steam is dispensed.
When you have fi nished, turn the knob until it is in the rest
position (
).
After dispensing steam, clean the steam wand as described on page 29.
Repeat the operation to
froth another beverage.
DISPENSING MAY BE PRECEDED BY SHORT SPURTS OF HOT WATER AND SCALDING IS POSSIBLE. THE HOT WATER/STEAM WAND MAY REACH HIGH TEMPERATURES: DO NOT TOUCH IT WITH BARE HANDS. USE THE APPROPRIATE HANDLE ONLY.
The display shows “brewing in
progress... steam”.
selected
steam
brewing in progress
steam
BEVERAGE DISPENSING
17
32
4 5
6
1
87
MAKING CAPPUCCINO
DISPENSING MAY BE PRECEDED BY SHORT SPURTS OF HOT WATER AND SCALDING IS POSSIBLE. THE HOT WATER/STEAM WAND MAY REACH HIGH TEMPERATURES: DO NOT TOUCH IT WITH BARE HANDS. USE THE APPROPRIATE HANDLE ONLY.
Press the
button.
Immerse the hot water/steam wand in the milk.
Turn the knob to the
position.
Froth the milk by gently swirling
the cup.
When you have fi nished, turn the knob until it is in the rest
position (
).
After dispensing, clean the wand as described on page 29.To brew 2 cappuccinos:
froth two cups of milk by following step 1 to 6;
brew two coffees by following steps 7 and 8 (in this case, press the
button twice).
Fill 1/3 of the cup with cold milk.
Press the
button once:
coffee dispensing begins.
Place the cup beneath the
dispensing head.
strong aroma
espresso coffee 08:33
selected
steam
18
1
2 3
5
4
6 7 8
Milk Island - 08
Type MKI002
Milk Island - 04
Type MKI001
MILK ISLAND (OPTIONAL)
This device, which may be purchased separately, enables you to easily and comfortably
prepare delicious cappuccinos.
Warning: before using the Milk Island, read the manual and all precautions carefully for correct use.
Important note: the quantity of milk in the carafe must never be below the “MIN” minimum level nor exceed the “MAX” maximum level. Thoroughly
clean all the Milk Island components after use.
To guarantee best results when preparing cappuccino, we recommend using cold (0-8°C / 32-45°F), partially skimmed milk.
Fill the milk carafe with the quantity of milk desired (between the MIN
and MAX levels indicated).
Place the milk carafe onto the base
of the Milk Island. Check that the
light on the base is green.
Remove the carafe using the handle.
Gently swirl the carafe and pour the milk into the cup.
Position the cup with frothed milk under the dispensing head. Brew coffee into the cup.
Turn the knob to the
position.
Wait for the milk to be frothed. When the desired quantity of froth
has been reached, turn the knob
until it is in the rest position ( ).
The machine will stop automatically after steaming continuously for 2 minutes. To dispense more steam turn
the knob to the (
) position and
then back to the
position.
19
BEVERAGE SETTINGS
The following page describes how to program coffee beverages; the programmable settings for each beverage may differ depending on the type of beverage.
PROGRAMMING FROM THE “BEVERAGE SETTINGS” MENU
To adjust the settings for preparing beverages: press the
button and select “beverage settings” by
navigating the click wheel with your fi nger.
In this phase you can:
exit the programming mode
(see page 21)
navigate the click wheel with your
fi nger to select:
- the quantity of coffee to brew;
- the coffee temperature;
- coffee prebrewing.
-adjust the quantity of coffee to be ground;
- adjust the coffee temperature;
- adjust coffee prebrewing.
restore factory settings
save the new settings
Every beverage can be programmed according to your individual tastes.
QUICK PROGRAMMING
You can program the quantity of coffee that will dispense into the cups when any beverage is selected. Select the type of beverage you want to program, then press and hold the
button until the display
shows (for example):
The machine dispenses coffee. When the desired amount is reached, press the
button again.
The display shows:
The dispensed quantity of coffee is memorized and replaces any previous settings.
programming
espresso coffee
saved
espresso coffee
1 beverage settings
20
1 2 3
4 5
6
7 8
9 10
Check that the water tank and
coffee bean hopper are full; place
the cup under the dispensing head.
Press the button.
Press the
button a few times to adjust the quantity of coffee to be ground or select the use of pre-
ground coffee. Press the
button to save.
Select the beverage to program.
Press the
button to confi rm.
Select “beverage settings”. Press the button to confi rm.
Change the coffee quantity by
navigating the click wheel with your
fi nger; confi rm with
.
Press the
button for more
than two seconds to access the
other programmable settings.
Change the temperature setting
(high, medium, low) by navigating the click wheel with your fi nger.
Press the
button to save.
Press the
button to select
the prebrew setting.
Change the prebrew value (normal, long, off) by navigating the click wheel with your fi nger. Press the button to save.
Press the
button to exit.
Prebrewing: the grounds are slightly dampened before brewing to bring out the full
aroma of the coffee and
enhance the fl avor.
strong aroma
espresso coffee 08:33
1 beverage settings
1.1 espresso coffee
medium aroma
espresso coffee
- + espresso coffee
temperature: medium
espresso coffee
temperature: medium
espresso coffee
prebrewing: normal
espresso coffee
prebrewing: normal
espresso coffee
When the settings are changed, the message on the
display starts fl ashing.
When the changes are saved
the message stops fl ashing.
BEVERAGE SETTINGS
1.
1.
2.
1.
2.
2.
2.
2.
1.
1.
Loading...
+ 53 hidden pages