Philips RI4412 User Manual

RI4444, RI4440, RI4430, RI4425, RI4422, RI4420,

RI4415, RI4412, RI4411, RI4410


18		19

English

Introduction

Congratulations on your purchase and welcome to Philips

Walita!To fully benefit from the support that Philips

Walita offers, register your product at www.walita.com.br.

General description (Fig. 1)

ASpray nozzle

BCap of filling opening

CSteam boost

DSpray button

ESteam control

FIonic DeepSteam button (RI4444, RI4440, RI4430)

GIonic DeepSteam light (RI4444, RI4440, RI4430)

HTemperature dial

IRI4425, RI4422, RI4420, RI4412: Amber temperature light with red automatic shut-off (AUTO/OFF) indicat ion. RI4415, RI4411, RI4410: Amber temperature light

JRI4444, RI4440, RI4430: Amber temperature light with red automatic shut-off (AUTO/OFF) indication

KMains cord

LType plate

MSoleplate

NCalc-Clean button

Not shown: Heat-resistant protective cover (RI4444, RI4440 only)

Not shown: Delicate fabric protector (RI4425, RI4415 only)

Important

Read this user manual carefully before you use the appliance and save it for future reference.

Danger

-Never immerse the iron in water.

Warning

-Check if the voltage indicated on the type plate corresponds to the local mains voltage before you connect the appliance.

-Do not use the appliance if the plug, the mains cord or the appliance itself shows visible damage, or if the appliance has been dropped or leaks.

-If the mains cord is damaged, you must have it replaced by Philips Walita, a service centre authorised by Philips Walita or similarly qualified persons in order to avoid a hazard.

-Never leave the appliance unattended when it is connected to the mains.

-This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

-Children should be supervised to ensure that they do not play with the appliance.

-Do not let the mains cord come into contact with the hot soleplate of the iron.

Caution

-Only connect the appliance to an earthed wall socket.

-Check the mains cord regularly for possible damage.

-The soleplate of the iron can become extremely hot and may cause burns if touched.

-When you have finished ironing, when you clean the appliance, when you fill or empty the water tank and also when you leave the iron even for a short while: set the steam control to position 0, put the iron on its heel and remove the mains plug from the wall socket.

-Always place and use the iron on a stable, level and horizontal surface.

-Do not put perfume, vinegar, starch, descaling agents, ironing aids or other chemicals in the water tank.

-This appliance is intended for household use only.

Electromagnetic fields (EMF)

This Philips Walita appliance complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user manual, the appliance is safe to use based on scientific evidence available today.

Before first use

1Remove any sticker, protective foil or plastic from the soleplate.

2Rinse and dry the filling cup.

423900068161

Preparing for use

Filling the water tank

1Make sure the appliance is unplugged.

2Set the steam control to position 0 (= no steam) (Fig. 2).

3Open the cap of the filling opening.

4Tilt the iron backwards and use the filling cup to fill the water tank with tap water up to the maximum. (Fig. 3)

Do not fill the water tank beyond the MAX indication.

Do not put perfume, vinegar, starch, descaling agents, ironing aids or other chemicals in the water tank.

,If the tap water in your area is very hard, we advise you to mix it with an equal portion of distilled water, or to use distilled water only.

5Close the cap of the filling opening (‘click’) (Fig. 4).

Setting the temperature

1RI4444, RI4440 only: Remove the heat-resistant protective cover (Fig. 5).

Do not leave the heat-resistant protective cover on the soleplate during ironing.

2Put the iron on its heel.

3To set the required ironing temperature, turn the temperature dial to the appropriate position (Fig. 6).

Check the laundry care label for the required ironing temperature:

-1for synthetic fabrics (e.g. acrylic, nylon, polyamide, polyester)

-1for silk

-2for wool

-3for cotton

-MAX for linen

If you do not know what kind or kinds of fabric an article is made of, determine the right ironing temperature by ironing a part that will not be visible when you wear or use the article.

Silk, woollen and synthetic materials: iron the reverse side of the fabric to prevent shiny patches.To prevent stains, do not use the spray function.

Start ironing the articles that require the lowest ironing temperature, such as those made of synthetic fibres.

4Put the mains plug in an earthed wall socket.

,The amber temperature light goes on.

5When the amber temperature light has gone out, wait a while before you start ironing.

The temperature light goes on from time to time during ironing.

Using the appliance

Note:The iron may give off some smoke when you use it for the first time.This stops after a short while.

Steam ironing

1Make sure that there is enough water in the water tank.

2Set the required ironing temperature (see chapter ‘Preparing for use’, section ‘Setting the temperature).

3Set the appropriate steam setting. Make sure that the steam setting you select is suitable for the set ironing temperature: (Fig. 7)

-1 - 3 for moderate steam (temperature settings 2 to 3)

-4 - 6 for strong steam (temperature settings 3 to MAX)

Note:The iron starts to produce steam as soon as it reaches the set temperature.

Note:If the set ironing temperature is too low (MIN to 2),water may drip from the soleplate (see chapter ‘Features,section‘Drip stop’).

Ironing with Ionic DeepSteam (RI4444, RI4440, RI4430 only)

When you use the Ionic DeepSteam function during steam ironing, the steam produced is finer than during regular steam ironing. Fine steam reaches deeper,

especially into thick fabrics.This helps you to remove stubborn creases easily.

1Follow steps 1 to 3 in section ‘Steam ironing’.

2Press and hold the Ionic DeepSteam button (Fig.8).

,The Ionic DeepSteam light goes on and you hear a humming sound. (Fig. 9)

3The iron now produces Ionic DeepSteam to help you remove even the toughest creases.

Note:The Ionic DeepSteam function is only effective when it is used in combination with a steam setting and a temperature setting between 2and MAX.

Note:Do not use the Ionic DeepSteam function when you iron without steam and/or at low temperature settings. However,ironing at low temperatures without steam with the Ionic DeepSteam function switched on will not damage the iron.

Note:The Ionic DeepSteam output may vary from time to time,depending on the ironing temperature.

Ironing without steam

1Set the steam control to position 0 (= no steam) (Fig. 2).

Do not use the Ionic DeepSteam function,as this function has no effect when you iron without steam.

2Set the required ironing temperature (see chapter ‘Preparing for use’, section‘Setting the temperature’).

After ironing

1Remove the mains plug from the wall socket.

2If you have been steam ironing, empty the water tank.

3Let the iron cool down in a safe place.

Features Spray function

You can use the spray function at any temperature to moisten the article to be ironed.This helps remove stubborn creases.

1Make sure that there is enough water in the water tank.

2Press the spray button several times to moisten the article to be ironed (Fig. 10).

Steam boost function

A steam boost from the special Steam Tip soleplate helps remove stubborn creases.The steam boost enhances the distribution of steam into every part of your garment.

The steam boost function can only be used at temperature settings between 3and MAX.

1Press and release the steam boost button (Fig.11).

Vertical steam boost

1You can also use the steam boost function when you hold the iron in vertical position. (Fig. 12)

This is useful for removing creases from hanging clothes, curtains etc.

Never direct the steam at people.

Drip stop

This iron is equipped with a drip-stop function: the iron automatically stops producing steam when the temperature is too low, to prevent water from dripping

out of the soleplate.When this happens, you may hear a sound.

Automatic shut-off function (RI4444, RI4440, RI4430, RI4425, RI4422, RI4420, RI4412 only)

The automatic shut-off function automatically switches off the iron if it has not been moved for a while.

,The redAUTO/OFF indication of the temperature light flashes to indicate that the iron has been switched off by the automatic shut-off function.

To let the iron heat up again:

1Pick up the iron or move it slightly.

,The red AUTO/OFF indication goes out.

2/7

,If the temperature of the soleplate has dropped below the set ironing temperature, the amber temperature light goes on.

2If the amber temperature light goes on after you have moved the iron, wait for it to go out before you start ironing.

Note:If the amber temperature light does not go on after you move the iron,the soleplate still has the right temperature and the iron is ready for use.

Delicate fabric protector (RI4425, RI4415 only)

The delicate fabric protector protects delicate fabrics from heat damage and shiny patches.

With the delicate fabric protector you can iron delicate fabrics (silk, wool and nylon) at temperature settings

3to MAX in combination with all steam functions available on the iron.

The delicate fabric protector reduces the soleplate temperature instantly, thus allowing you to iron delicate fabrics safely.

If you do not know what kind or kinds of fabric an article is made of, determine the right ironing temperature by ironing a part that is not visible when you wear or use the article.

1Put the iron on the delicate fabric protector (‘click’) (Fig. 13).

Cleaning and maintenance Cleaning

1Wipe flakes and any other deposits off the soleplate with a damp cloth and a non-abrasive

(liquid) cleaning agent.

To keep the soleplate smooth, avoid hard contact with metal objects. Never use a scouring pad,vinegar or other chemicals to clean the soleplate.

2Clean the upper part of the iron with a damp cloth.

3Regularly rinse the water tank with water. Empty the water tank after you have rinsed it.

Double-Active Calc System

The Double-Active Calc System consists of an Anti-Calc tablet inside the water tank combined with the CalcClean function.

1The Anti-Calc tablet prevents scale from clogging the steam vents.This tablet is constantly active and does not need to be replaced.

2The Calc-Clean function removes the scale particles from the iron.

Using the Calc-Clean function

Use the Calc-Clean function once every two weeks. If the water in your area is very hard (i.e. when flakes come out of the soleplate during ironing), use the Calc-Clean function more frequently.

1Make sure the appliance is unplugged.

2Set the steam control to position 0.

3Fill the water tank to the maximum level.

Do not put vinegar or other descaling agents in the water tank.

4Set the temperature dial to MAX (Fig. 14).

5Put the plug in an earthed wall socket.

6Unplug the iron when the temperature light goes out.

7Hold the iron over the sink, press and hold the

Calc-Clean button and gently shake the iron to and fro (Fig. 15).

,Steam and boiling water come out of the soleplate. Impurities and flakes (if any) are flushed out.

8Release the Calc-Clean button as soon as all the water in the tank has been used up.

Repeat the Calc-Clean process if the iron still contains a lot of impurities.

After the Calc-Clean process

1Put the plug back into the wall socket and let the iron heat up to let the soleplate dry.

2Unplug the iron when it has reached the set ironing temperature.

3Move the hot iron gently over a piece of used cloth to remove any water stains that may have formed on the soleplate.

4Let the iron cool down before you store it.

Storage

1Set the steam control to position 0 and unplug the iron.

2Empty the water tank (Fig. 16).

3Let the iron cool down in a safe place.

4Wind the mains cord and fix it with the cord binder. (Fig. 17)

5Store the iron on its heel on a stable surface.

Heat-resistant protective cover (RI4444, RI4440 only)

You can store the iron on the heat-resistant protective cover immediately after ironing. It is not necessary to let the iron cool down first.

Do not use the heat-resistant protective cover during ironing.

1Put the iron on the heat-resistant protective cover (Fig. 18).

2Insert the tip of the soleplate into the heatresistant protective cover (1) and then press down the heel of the iron (2).

Environment

-Do not throw away the appliance with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. By doing this, you help to preserve the environment (Fig. 19).

Guarantee & service

If you need information or if you have a problem, please visit the Philips Walita website at www.walita.com.br or contact the Philips Walita Customer Care Centre in your country

(you find its phone number in the worldwide guarantee leaflet).If there is no Customer Care Centre in your country, go to your local Philips Walita dealer or contact the Service Department of Philips Walita Domestic Appliances and

Personal Care BV.

Troubleshooting

If the appliance does not work or does not work properly, first check the list below. If the problem is not mentioned in this list, the appliance probably has a defect. In that case we advise you to take the appliance to your dealer or to an authorised Philips Walita service centre.

Problem	Possible cause	Solution

The iron is	There is a	Check the mains
plugged in, but	connection	cord, the plug and
the soleplate is	problem.	the wall socket.
cold.
	The	Set the
	temperature	temperature dial
	dial is set to	to the required
	MIN.	position.
The iron does	There is not	Fill the water
not produce any	enough water	tank (see chapter
steam.	in the water	‘Preparing for use’,
	tank.	section ‘Filling the
		water tank’).
	The steam	Set the steam
	control is set	control to a
	to position 0.	position between
		1 and 6 (see
		chapter ‘Using the
		appliance’, section
		‘Steam ironing’).
	The iron	Set an ironing
	is not hot	temperature that
	enough and/	is suitable for
	or the drip-	steam ironing (
	stop function	2to MAX).
	has been	Put the iron
	activated.	on its heel and
		wait until the
		temperature light
		has gone out
		before you start
		ironing.

Problem	Possible cause	Solution

The iron does	You have used	Continue ironing
not produce a	the steam	in horizontal
steam boost.	boost function	position and
	too often	wait a while
	within a very	before you use
	short period.	the steam boost
		function again.
	The iron	Set an ironing
	is not hot	temperature at
	enough.	which the steam
		boost function
		can be used (
		3to MAX).
		Put the iron
		on its heel and
		wait until the
		temperature light
		has gone out
		before you use
		the steam boost
		function.
Water droplets	You have not	Press the cap until
drip onto the	closed the	you hear a click.
fabric during	cap of the
ironing.	filling opening
	properly.
	You have put	Rinse the water
	an additive	tank and do not
	in the water	put any additive in
	tank.	the water tank.
	The set	Set a temperature
	temperature	of or 2higher.
	is too low for
	steam ironing.
	You have	Set the
	used the	temperature
	steam boost	dial to a setting
	function at a	between 3
	temperature	and MAX.
	setting below
	3.
Water drips from	You have put	Empty the water
the soleplate	the iron in	tank.
after the iron has	horizontal
cooled down or	position with
has been stored.	water still left
	in the water
	tank.
Flakes and	Hard water	Use the Calc-
impurities come	forms flakes	Clean function
out of the	inside the	one or more
soleplate during	soleplate.	times (see
ironing.		chapter ‘Cleaning
		and maintenance’,
		section ‘Using
		the Calc-Clean
		function’).
The red light	The automatic	Move the
flashes (RI4444,	shut-off	iron slightly to
RI4440, RI4430,	function has	deactivate the
RI4425, RI4422,	switched	automatic shut-off
RI4420, RI4412	off the iron	function.The red
only).	(see chapter	AUTO/OFF light
	‘Features’,	goes out.
	section
	‘Automatic
	shut-off
	function’).
The iron makes a	The Ionic	If you hear the
humming sound.	DeepSteam	humming sound
	function is on.	when you iron
		without steam,
		stop pressing the
		Ionic DeepSteam
		button.The Ionic
		DeepSteam
		function has no
		effect when you
		iron without
		steam.

423900068161

3/7

+ 4 hidden pages