Philips RG4172BK User Manual

T374AH REMOTE CONTROL INSTRUCTIONS

The T374AH remote control is used to perform setup and verification operations on Philips Consumer Electronics Company commercial chassis. This remote is fully backward compatible with previous commercial chassis setup remotes, but has added functionality. The three buttons at the bottom of the remote,

TV Guest, TV Setup, and DCM Setup,

are called function buttons. They are used to select the desired function to be performed.

TV Guest mode will emulate the “Guest” remote commands. This provides the installer the ability to verify proper “Guest Remote” operation using only one remote. Only the commands supported on the “Guest” remote may be valid. To use this function, press the TV GUEST button, then press any button that corresponds to the “Guest Remote.” The remote will remain in the TV Guest mode until another function button is pressed.

TV Setup mode is used to set all the TV control settings and commercial features. This function is completely backward compatible with previous setup transmitters but has additional buttons that are valid for newer TV control systems. The remote will remain in the TV Setup mode until another function button is pressed.

DCM Setup (Data Communication Module) mode is similar to the TV Guest Mode except the Select and Cursor keys send “Softkey” commands, allowing the DCM to have its own setup keys. The function of these keys will depend upon each DCM manufacturer. The remote will remain in the DCM Setup mode until another function button is pressed.

Softkey is defined as a command that is never acted upon by the TV control system. It is always passed through the “Smart Port” to the DCM. Each DCM manufacturer can make its own interpretation of the function of the key. The functional description of the TV controls and features are as follows: To set up the TV, press the TV Setup button to place the remote in TV Setup mode.

Channel Guide

This feature is activated with the Guest or Setup remote’s CH GDE button. This feature uses the labels that are assigned by the channel labeling function described on page three. Once activated by pressing the CH GDE button, the TV lists the Channel Labels for channels with assigned labels. Channels that are not in the Favorite Station memory (see “ADD CHANNEL” on page four) will not be displayed. Each listing or “page” will show seven channel labels. Each press of the CH GDE button will show subsequent channel listing pages if they exist. The maximum number of labels that can be displayed is 32. If CH GDE is not pressed for seven seconds, the listing will timeout. If any other remote command is sent that requires the television on-screen display, the listing will be cleared, and that command invoked.

IMPORTANT: When programming is complete, press or depress the RECALL button to save the program changes in the TV memory.

To adjust the TV for either Hotel or Consumer mode, press the TV SETUP button on the remote, then enter the numerical sequence 02 49 95, then press the SELECT button. Choose between Hotel or Consumer mode by pressing either the + or - button. Only a limited amount of features are available in Consumer mode.

IB7166E002

MAC 6009

SLEEP

ENTER

P.PREF

CH GDE

POWER

VOL

A/CH

MUTE

EFG

1 4

2 5 8 0

SETUPSETUPGUEST

DCM

RECALL

3 6 9

SLEEP

ENTER

P.PREF

CH GDE

POWER

VOL

A/CH

MUTE

EFG

1 4

2 5 8 0

DCM SETUPSETUPGUEST

RECALL

3 6 9

2 3

This function allows individual channels to be added or deleted from memory. Tune the desired channel by using the CHANNEL UP/CHANNEL DOWN buttons or by random access, and

then press the + or - button to either add or remove a channel from memory.

This function will give a name, up to eight characters, to a channel. Press the - button to delete any existing label. Press the + button to activate this function. Once in modification display, a cursor will point

to the position on the label. The + and - buttons will scan through the available characters. The RESET button will move the cursor to the next position on the label. A total of 32 channels may be labeled.

+ ADD CHANNEL

-> DELETE xx

LABEL xx + MODIFY

- DELETE

Press the + button to allow the continuous display of the current channel number. Press the - button and the channel number will appear for only a few seconds after the channel

change. It will then disappear.

+ REMINDER ON

-> REMINDER OFF

This function will determine what channel the TV will tune to at initial turn on. Tune any channel and press the + but-

ton. The TV will tune to that channel every time it is turned on. Press the - button and the TV will, at turn on, tune to the last channel tuned before turn off.

+ FORCE TO CH xx _>STD PWR ON CH

Press the + button for the “POWER FORCED ON” mode. This disables the normal on/off control; the receiv-

er will be activated once AC power is applied. The “sleep timer” function is disabled; the set may not be turned off except by removing power. Press the - button for normal “POWER ON/OFF” control.

+ PWR FORCED ON

-> STD PWR ON/OFF

The “NO DISPLAYS” function disables any on-screen displays, except the sleep timer and mute. Press the + button to activate this function. Press the - button for standard displays.

+ NO DISPLAYS

-> STD DISPLAYS

The “TIME LIMIT” function will automatically turn off the set if it has been on continuously for the time duration shown. Press the + button to activate the function and set the time

limit, up to 99 hours. Press the - button for normal TV operation.

+ TIME LIMIT xx HR

-> NO TIME LIMIT

Press the + button to enable the Channel Guide feature. Press the - button to disable the function.

+ CH GDE ENABLE _> CH GDE DISABLE

Press the + or - button to adjust the picture to the desired level.

PICTURE

-.................+

To begin programming, press the TV SETUP button on the remote control to put the remote into TV setup mode. Then press the POWER button to turn on the TV. Press the SELECT button for the display access functions to appear on the screen. Depending on the model and its features, some or all of the display functions and features described below will be valid.

Press the + or - button to adjust the brightness to the desired level.

BRIGHTNESS

-.................+

Press the + or - button to adjust the color to the desired level.

COLOR

-.................+

Press the + or - button to adjust the tint to the desired level.

TINT

-.................+

Press the + or - button to adjust the sharpness to the desired level.

SHARPNESS

-.................+

Press the + or - button to set the maximum volume available from the keyboard or the Guest transmitter.

VOLUME LIMITER

-.................+

Press the + button to disable the normal functioning of the volume control. This forces the volume to the

maximum level allowed by the volume limiter described in the next step. In this mode, the mute function is disabled. Press the (-) button for “standard volume up/down,” allowing normal volume control operation.

+ VOLUME FORCED MAX

->STD VOL UP/DOWN

Press the VOLUME UP or VOLUME DOWN button to set the maximum level available. The range is made up of 63 steps from minimum to maximum.

+ SET MAX VOL xx (VOL FORCED MAX)

Press the + or - button to choose between maximum volume or the “turn on” volume. Press the VOLUME UP or

VOLUME DOWN button to set either the maximum volume level available, or the set’s initial “turn on” volume level. There are 63 steps between minimum and maximum.

++SET MAX VOLUME

->SET ON VOL

Press the + button to have the TV receive cable channels 1125, excluding channels 95, 96, and 97. Press the - button to have the TV receive the normal off-the-air channels 2-69.

+ CABLE TUNING

-> BCST TUNING

This function allows the TV to scan all the channels and automatically program in memory all active channels on the system. Press the + button to activate auto pro-

gramming. Press the - button at any time to stop this function.

AUTO PROGRAMMING + TO BEGIN

Press the + or - button to turn Smart Sound ON or OFF. Smart Sound allows you to preset a desired volume level that the TV sound will not exceed.

SMART SOUND ON/OFF

Press the + or - button to select the language you prefer. You may choose English, Spanish (Español), or French (Français),

LANGUAGE ENGLISH/ESPAÑOL/FRANÇAIS

Press the + or - button to turn AV MUTE On or Off. When AV MUTE is active, the audio is muted and the screen will be solid black or solid blue if a clear signal is not received.

AV MUTE ON/OFF

Press the + or - button to select YES or NO. Select YES when you are ready to leave the on-screen menu system.

EXIT NO/YES