Philips QS6160 User Manual

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

When using an electric appliance, basic safety
precautions should always be followed, including
the following:

Read all instructions before using this

appliance.

DANGER

To reduce the risk of electric shock:

1. Do not reach for a charging stand while
plugged in that has fallen into water. Unplug
immediately.

2. Power plug and the accessories connected
to it are not for immersion or for use in
shower.

3. Do not use an extension cord with this appli
ance.

4. Always unplug the charging stand from the
electrical outlet immediately after use.
except when StyleShaver is (re)charging.

5. Unplug and remove power supply cord from
charging stand before cleaning.

6. When discarding SwIeShaver, unplug charging
stand and remove StyleShaver from charging
stand before removing rechargeable
batteries. See Battery Kemoval instructions.

7. The batteries used in this device may
present a fire or chemical burn hazard if
mistreated. Do not disassemble, heat above
lOO^C (212*F) or incinerate.

WARNING

To reduce the risk of burns, fire, electric
shock or injury to persons:

1.

Close supervision is necessary when this
StyleShaver/chargjng stand is used by. on. or
near children or invalids.

2.

Use this StyleShaver/charging sund for its
intended household use as described in this
manual. Do not use attachments not
recommended by Philips Electronics North
America Corporation.
Never operate this StyleShaver/charging

3.
stand if it has a damaged cord or charging
plug, if it is not working properly, if it lus
been dropped or damaged, or dropped into
water. For assistance call 1-800-243-3050.

4. Keep the StyleShaver. charging stand, cord
and charging plug away from heated surfaces.

5. Never drop or insert any object into any
opening.

6. Never operate the StyleShaver with the air
openings blocked or while on a soft surface,
such as a bed or couch, where the air
openings may be blocked. Keep the air
openings free of lint. hair, and the like.

7. Do not operate, charge or plug in
StyleShaver outdoors or where aerosol
(spray) products are being used or where
oxygen is being administered.

8. Always check foil, cutters, trimmers and
combs before using the StyleShaver. Do not
use the StyleShaver if foil, cutters, trimmers
or combs are damaged, as injury may occur.

9. Always attach plug to charging stand first,
then charging plug into outlet.To disconnect,
remove charging plug from outlet.

10. Use only the cora and charging stand
provided to charge and (re)charge the

StyleShaver.

11. If the appliance is subjected to a major
change in temperature, pressure or
humidity, let the appliance acclimatize for
30 minutes before using.

12. Never put the StyleShaver/charging stand in
direct sunlight or store at a temperature
above 140°h

13. To prevent possible damage to the cord, do
not wrap cord around the charging stand.
Do not store in a damp environment.

14. Only use the power plug and other
accessories supplied wi№ the StyleShaver.

SAVETHESE

INSTRUCTIONS

IMPORTANT: The power plug contains a
transformer. Do not cut off the power plug
to replace it with another plug, as this will
cause a hazardous condition.

Registration

Congratulations on your purchase and welcome
to Philips Norelco!

To fully benefit from the support that Philips

Norelco offers, register your product at
www.norelco.com/register

Features

a

m

*

' 0 i

V.

0'

^ / /-lU

%C

0^

Create Your Own Look

Your new Philips Norcko StyleShaver offers you
a safe, gentle and quick way to trim or shave facial
hair.This unique combination allows you to create
your own look safely and with less irritation. The
zoom wheel gives you multiple har length settings
to choose from so you can control the exact
hair length you desire or use the shaving unit to
completely shave off facial hair Your StyleShaver
will give you a precise trim and shave anywhere,
every tinxi.

Like many rvcw products, your Philips Norelco
StyleShaver may take a little getting used to. If
you are shaving sensitive areas for the first time,
your skin may need time to adapt Give yourself
some time to acquaint yourself with your new
StyleShaver.

Stick with it! If you alternate trimming or shaving
methods during the adjustment peri^ it may
make it more difficult to adapt to the Philips
Noroko StyleShaver. If you are still not convinced.
Philips Noreko will refund you the full purchase
price as long as the request is received within 45
days of purchase.

Features

A Full-size trimmer (1 17/64 in./32 mm)
B Trimming head
C Precision detail trimmer (5/8 in./15 mm)
D Guiding groove
E Zoom v/heel
F On/off button
G Travel lock indication (QS6160 only)
H Shaving head on/off button
I Shavir^ head

J Battery status indicator

K Beard comb
L Detail comb (QS6160 only)
M Charging stand
N Adapter with small plug
O Protective cap

Cleaning brush
Storage pouch (QS6160 only)
Full 2-Year Warranty
45-Day Money-Back Guarantee

This symbol indicates that
the StyleShaver can be used
in the bath or shower.

Battery Status Indicator

I The Battery Status Indicator on the StyleShaver

will flash white to indicate StyleShaver is
(re)charging.

I The Battery Status Indicator lights up white

continuously to indicate the StyleShaver is fully
charged.

I After StyleShaver is fully charged, the charging

light goes out after 30 minutes to save energy.

Before First Use

I Charge the StyleShaver before you start

using it (see 'Charging'). Make sure the
StyleShaver is switched off before you start
clurging it.

> Before using, check foil, cutters, trimmers and

combs for wear or damage. If foil, cutters,
trimmers or combs show signs of wear or
damage, do not use StyleShaver as injury may
occur. Do not use StyleShaver until foil,
cutters, trimmers or combs have been replaced.

Charging

> Charging requires 1 hour (QS6160) or

4 hours (QS6140).

I Use only the power cord and charging stand

provided.

I Charging, recharging or scoring at temperatures

below 40'*F or higher than 95®F adversely
affects lifetime of batteries.

I The StyleShaver can only be charged in the

charging stand.

n Be certain StyleShaver is OFF.

□ Connect poNver cord to charging stand (Rg. 1).
NOTE The small plug is easiest to insert when

the charging stand is folded.

□ Unfold the charging stand (Rg. 2).

□ Plug the adaptor into any 120V AC oudet.

Use only the power cord provided.

I An adaptor plug may be necessary for power

cord usage in some foreign countries. Use an
attachment plug adaptor of the proper
configuration for the power outlet.

B Put the StyleShaver in the charging stand with

the shaving head pointing upwards (Fig. 3).
Make sure the charging contacts on each side
of the StyleShaver fit into the charging stand
correctly. When placed correctly, the
charging tight will flash white to indicate the
StyleShaver is (re)charging (Fig. 4).

Q A fully charged StyleShaver has a cordless

grooming time of up to 75 minutes.

a

When the battery is fully charged, the
Battery Status Indicator lights up white
continuously for 30 minutes and then
will go out.

□ Disconnect the power cord and unplug from

the electrical outlet.

Recharging

D Recharge when the Battery Status Indicator

flashes orange. This indicates there is
approximately 10 minutes of operating
time left.

If the Battery Status Indicator flashes orange

quickly, the battery is completely empty. Charge

the StyleShaver before using.

B When StyleShaver is fully charged, disconnect

the power cord and unplug from electrical
outlet.

Trimming

I Use this StyleShaver for its intended household

use as described in this manual.

I Always comb your beard and/or moustache

with a fine comb before you start trimming.

I If you are trimming for the first time, be

careful. Do not move the StyleShaver too fast.
Make smooth and gentle movements.

I After trimming, residual hair length can vary

depending on hair type.

Trimming With Trimming Comb

I The trimming combs let you trim facial hair

to different lengths.

I Use the beard comb to trim your beard and

mousuche.

I Use the detail comb (QS6I60 only) to trim

hard-to-reach areas, such as under the nose.

I Trimming is easier when the skin and hair

are dry.

> The hair length settings are indicated on the

StyleShaver.The settings correspond to the
remaining hair length after trimming.

I The trimming combs cut hair to a length of

3/64- 13/32 in. (1-10 mm).

D Hold the StyleShaver in the trimming

position, with the trimming head pointing
up (Fig. 5).

B Slide the trimming comb into the guiding

grooves of the St)4eShaver (Fig. 6).

B Press and turn the Zoom Wheel left or right

to select a setting (Fig. 7). See Table for
settings and corresponding hair lengths.

-The line above the Zoom Wheel indicates the
setting selected (Rg 8).

> If you are trimming for the first time, start by

using the maximum trimming length setting
of 13/32 in.(10mm) to prevent accidentally
trimming hairs too shorcAs you become
familiar with the settings, adjust Zoom Wheel
to desired trimming setting.

□ Press the trimming head on/off button once

to turn trimming head ON (Fig. 9).
The on/off button lights up to indkate trimming
head is ON (QS6160 only).

I If you turn the trimming head on while the

shaving head is also on. the shaving head will
turn off.

B To trim in the most effective way. move the

StyleShaver against the direction of hair

growth. Do not move the StyleShaver too

fast. Make smooth and gentle movements and

make sure the surface of the trimming comb

always stays in contact with the skin (Fig. 10).

NOTE: Since all hairs do not grow in the same
direction, you may want to try different trimming
pQsrtions_(i.e.. upwards. downwacds or across).
Practice is best for optimum resuKs.

□ Turn the StyleShaver OFF.

B Clean the StyleShaver (see section 'Cleaning').

Trimming Length Settings Table

Hair length setting Hair length after trimming

No comb

1 3/64 inch - 1 mm

2 5/64 inch - 2 mm

3
4 5/32 inch - 4 mm
5
6
7 9/32 inch - 7 mm
8
9 3/8 inch - 9 mm

10 13/32 inch - 10 mm
Trimming Without ATrimming Comb
Remove trimming comb to cut hair close to the

skin (approximately 1 /32 in. /0.5mm)
D Be certain StyleShaver is in the OFF position.

1/32 inch - 0.5 mm

1/16 inch - 1.5 mm

3/32 inch - 2.5 mm
1/8 inch - 3 mm

3/16 inch - 5 mm
1/4 inch - 6 mm

5/16 inch - 8 mm

B Remove the trimming comb by pulling it off

the StyleShaver (Rg. 11).
Never pull off comb by grasping the flexible top
portion. Always pull off by the bottom part of the
conk>.

B Press the trimming head on/off button once

to turn trimming head ON (Fig. 9).
□ Hold the StyleShaver in the trimming

position, with the trimming head pointing

up (Fig. 5).

B Make downward strokes with the broad

side of the trimming head.

Using the Precision Trimmer
Use the precision trimmer for precise trimming

around cars. skJcboms, mouth and under the nose.
□ Turn the trimmer head until the precision

trimmer points to the front of the
StyleShaver (Fig. 12).

Q Press the trimming head orVoff button to

turn trimming head ON (Fig. 9).

D Hold the StyleShaver with the trimming head

pointing up and make downward strokes
with the precision trimmer.

Shaving

I The StyleShaver should be used on fecial

hair only.

I Use the shaving head with shaving gel or foam

for extra skin comfort or use dry for extra
convenience.

I When shaving sensitive areas for the first time,

you may feel some discomfort, irritation or
reddening of the skin. This is normal as your
skin needs time to adjust to shaving.

I If your hair is l^ger than 13/32 in. / 10 mm. trim

hair using a trimmer comb first for optimum
shaving results.

I Be certain that your skin is clean before using

the StyleShaver.

I Make sure the shaving head is in complete

contact with your skin for the closest shave

and minimum foil wear.
I Pressing too hard may cause skin irritations.
I Practice is best for optimum results.

D Hold the StyleShaver in the shaving position,

with the shaving head pointing upwards and
the trimming head pointing downv^rds
(Fig.13).

Q Turn StyleShaver ON by pressing the shaving

head on/off button (Fig. 14).
The on/off button lights up to indicate shaving
head is on (QS6160 only).

B Stretch your skin taut with your free hand

and gently press StyleShaver to skin and

move it slovdy and smoothly against the

direction of hair growth (Fig. 15). DO NOT

press too hard.Too much pressure can

distort the foil and cause skin irritation.
For optimal results, make circular movements
during use.

□ Make sure the shaving head is always in full

contact with your skin.

TIP: If using wtt, rinse the shoving head often under
the tap to ensure it continues to glide smoothly over
your skin.

B Turn StyleShaver OFF by pressing the shaving

head on/off button (Fig. 14).

Overload Protection
If you press the trimming or shaving head too hard

on your skin or the cutting element gels bkxked.
the on/off button of the blocked trimming or
^ving head quickly flashes (QS6160 only) and
the appliance turns off automatically. Clean the
appliance (see 'Cleaning' section).

CI c Л n i n g

I The StyleShaver should be cleaned after each

use.

I Always switch StyleShaver OFF and remove

StyleShaver from charging stand before cleaning.

I Do not use compressed air. abrasive

cleaning agents, scourers or aggressive liquids
such as alcohol, benzene bleach or acetone to
clean the appliance.

I Never clean, remove or replace trimmer or

shavir^ head assembly while motor is on.

I Do not apply pressure to shaving head. Do not

touch foil with hard objects as this may dent or
damage foil or cutters. If damage occurs, replace
damaged parts.

I Do not use StyleShaver if foil, cutters, trimmers

or combs are damaged or broken as injury
rrtay occur.

I Only use the cleaning brush supplied. Any other

brush may cause damage.

□ Use the cleaning brush to remove hairs

from the cutters (Fig. 18).

B Do not use a towel or cloth to dry shaving

foil or cutters as this may cause damage. Allow
to air dry thoroughly.

□ Reattach the shaving head by snapping it back

onto the StyleShaver (Rg. 19). You will hear a
‘click*.

Cleaning the trimming head

O Always switch StyleShaver OFF and remove

StyleShaver from the charging stand before
cleaning (Fig. 9).

B Pull the comb off the trimming head (Fig. 11).
B Rinse the trimming head with warm running

tap water (Fig. 20).

Cleaning the trimming head connector
Note: Make sure to clean the trimming head

connector at least every 3 months.

D Always switch StyleShaver OFF and remove

StyleShaver from the charging stand before
cleaning (Fig. 9).

B Gently pull trimming head off the StyleShaver

(Fig. 21).

B Remove the hairs from the inside of the

trimming head connector with the cleaning
brush (Fig. 22).

□ Clean the inside of the trimming head with

the cleanir^ brush (Fig. 23).

B Place the trimming head back on the

StyleShaver (Rg. 24).

Replacing the Shaving Foil Head

I if the shaving foil and cutters are worn or

damaged, do not continue using the StyleShaver.
Replace the shaving foil and cutters immediately.

> It is recommended that you replace your

shaving foil and cutters once a year.

t A worn or damaged shaving foil or cutters

should only be replaced with an original Philips
Norelco shaving foil, rrtodel QS6100, which is
available on the Philips Norelco website.
www.philips.com/support or call
1-800*243-3050 for assistance.

> The foil is a precision part. Handle with care.

D Always switch StyleShaver OFF and remove

StyleShaver from the charging stand before
replacing shaving foil.

B Remove the shaving foil head by pulling it off

the appliance.

B Place the new shavir^ foil head on the

StyleShaver by snapping it into place. You
will hear a "click".

After replacing the shaving foil head, check that
the shaving head is firmly attached before using
StyleShaver.

This StyleShaver has no other user-serviceable
parts. For assistance call 1 •8QO-243-3Q5Q.

Travel Lock (QS6160 only)

You can lock the appliance when you arc going to
travcI.The travel lock prevents the appliance from
being switched on by accident.

Activating the travel lock

n Press and hold the trimming on/off button

or the shaving on/off button for at least
4 seconds.

i The travel lock indication flashes 3 times.

The travel lock is only activated when the
indication lights up continuously.

Deactivating the travel lock

n Press and hold the trimming on/off button

or the shaving on/off button for at least
4 seconds.

Storage

> Fold the charging stand for easy travelling or

storage (Rg. 25).

I Put the protective cap on the shaving head

(Fig. 26).

I Be sure StyleShaver is turned off. Remove

power cord from outlet and charging stand

before storing in a safe, dry location where it
will not be crushed, banged, or subject to
damage.

> Do not wrap power cord around StyleShaver/

charging stand when storing.

I Store cord in a safe location where it will not

be cut or damaged.

I Do not place or store StyleShaver/charging

stand where it can fell or be pulled into a tub
or sink, water or other liquid while plugged in.

Battery Removal

The StyleShaver battery may only be removed
when the StyleShaver is to be discarded.

I This Philips Norelco StyleShaver contains

a Lithium-Ion rechargeable battery which must
be disposed of properly (Fig. 27).

> For assistance, call toil free: 1-800-243-3050

or visit our website,

n Be certain StyleShaver is OFF and removed

from charging stand before dismanding.
Allow the StyleShaver to run until the
batteries are completely empty/depleted.
Turn StyleShaver OFF.

www.philips.com/support.

B Remove the shaving head and cutters from

appliance.

B Undo the four screws of the top cover with

a screwdriver.

□ Remove the cover.

B Insert a screwdriver under the back panel

and remove panel.

B Insert a screwdriver under the cover of the

basic body and remove cover.

You will see a printed circuit board.

B Break the battery from the printed-circuit

board.

Be carefL,!. Uie baUery sLnps ar e very_sharp.

B Do not attempt to replace battery. Insulate

battery ends by covering with cape and/or
place battery in a small plastic bag.

B Discard StyleShaver. Do not attempt to plug

electrical cord into the outlet or recharge
StyleShaver after the batteries have been
removed.

iQ Contact your local town or city officials

for battery disposal information or call
1-800-8-BATTERY or
drop-off locations.

Assistance

For assistance, visit our website:

www.philips.com/support or
call 1-800-243-3050

Online information is available 24 hours a day.
7 days a week.

Accessories

I For maximum StyleShaver performance replace

shaving foil head once a year.

> Replacement Shaving Foil Head

may be purchased on our website
www.philips.com/store

www.rbrc.com for

PHILIPS

^NORELCO

Styleshover

QS6160
QS6140

Rechargeable
Cordless

Always here to help you

Register your product and get support at

www.norelco.com/register

4222 002 8424 3

PHILIPS

£nOnELCO

45-DAY MONEY-

BACK GUARANTEE

If you are not fully satisfied with your Philips Norelco
StyleShaver send the product bade and we’ll refund you
the full purchase price.

The StyleShaver must be shipped prepaid by
insured mail, insurance prepaid, have the original
sales receipt, indicating purchase price and date
of purchase, and the money-back guarantee
return authorization form enclos^.Wc cannot
be responsible for lost mail.
The StyleShaver must be postmarked no later
than 45 days after the date of purchase. Philips
Norelco reserves the right to verify the purchase
price of the product and limit refunds not to
exceed suggested retail price.

To obtain money-back guarantee return
authorization form, call 1-800-243-3050 for
assistance.

Delivery of refund chedc will occur 6-8 weeks AFTER
receipt of returned product.

Full Two-Year Warranty

Ptwos flKtiwcs North Алпспса Corporat«« warrants each new
PMf» Nortfeo product Model QS616CXOS6140 (except foi cutters
arxl cont») agiwtst defects n nuterub or vvorferxanshp (or a peood of
two )«irs tom the date of ptrehase. and agrees to repar or replace any
defectne p -x-i - *«hoirt charge

IMPORTANT: Ihe warranty doe not COs«r damage resukitg from
accident тнме or abuse, lad: of reasonable care, the alVtcng of any
attachment not prosnded with the prodxt or loss Ы parts or sUOjcetng
the product to any but the spcciAed vokage * Use of unauthonied
replacement parts will vod this vrarrarsty

PHILIPS EUCTRONICS NORTH AMERICA CORPORATION
WILL NOT PAY FORWARRANTY SERVICE PERFORMED BY
A NON-AUTHORIZEO REPAIR SERVICE AND WILL NOT

REIMBURSE THE CONSUMER FOR DAMAGE RESULTING FROM
WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZEO

REPAIR SERVICE.

NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAU

INCIDENTAL OR CONSEQUENTIAL DAMAGES,
fe order to obcan warranty service, smpb' go wwwphlpsconV
rxxelco or cjf 1 -800 243-30S0 (or assetarKe. R is suggested that for
yo«r protection you return sl^xneiCs of product by nswed mai.
Yisurance prepaid Oamage occurring during shymeni is not co,«red by
thR wanranty NOTE; No other varrantywrittcft or oral isauthorvcd
by PMps Uectroracs North Amenca Conx>rabon.The warranty gives
you speefk legal nghts. and you may also have other nghis whch vary
from state to state Some states do not atow the exetJw or imitation
of Aodental or conse^aetxial damages, so the above cxciiscn and
hmilitions may not apply to you

*Read enclosed nstrucuons carefuHy

Mam/actured for.
Avips Consumer L/estyle
A Oms«n of Midps £)Mtronics North Amerxa Corporation
ROeox 1031XStam.ford.CT(J64M

INs symbol on the products rumcpliu men it b

Mrdby ISidrrwnleT\'ljlwSGrcv Ira

®

NoreltoáalVytmcdTradtmrkcfrhapsncca'ciiics
North Amenca Corporaborx

(4 Я PS « a RrgBtcfrdTradmwIc of Korrtd^ f>dpt NV

О TOia ft4|ii HnSraiiKS Nordi ^raiva СхэгрсгаЬэт ^ RlpCs Rrwvvvl

Cleaning the shaving head
D Always switch StyleShaver OFF and remove

StyleShaver from the charging stand before
cleaning (Fig. 9).

B Remove the shaving foil head by pulling it off

the appliance (Fig. 16).

Hold the shaving l^ad by the plastic housing only.

B Rinse the shaving head under warm running

tap water to rinse away debris (Fig. 17).

Do not use t*'e cleaQing b^usn to clean the shavng

head as this may cause damage,

i The travel lock indication flashes 4 times.

The travel lock is now deactivated and the
StyleShaver switches on.

NOI LI he bdvel lock is deacUvdled dL^lorndUcdlly

when you charge the appliance.