Philips QC5580-40 User Manual

ENGLISH

IMPORTANT

SAFETY

INSTRUCTIONS

When using an electrical appliance, basic safety precautions should always be followed, including

the following:

Read all instructions before using this

appliance.

DANGER

To reduce the risk of electric shock;

Do not reach for a clipper that has fallen into

water. Unplug immediately. Use clipper only in dry condition. Do not use while bathing or in a shower. Do not submerge clipper in water. Do not place or store clipper where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid. Always unplug this clipper from the electrical

5. outlet immediately after using, except when clipper is (re)charging.

Unplug and remove power supply cord from clipper before cleaning. The batteries used in this device may present

7. a fire or chemical burn hazard if mistreated. Do not disassemble, heat above 100°C (212°F) or incinerate.

WARNING

To reduce the risk of burns, fire, electric shock or injury to persons:

Close supervision is necessary when this appliance is used by, on, or near children or invalids.

Use this clipper for its intended household use as described in this manual. Do not use attachments not recommended by Philips Electronics North America Corporation.

3. Never operate this clipper if it has a damaged cord or plug, if it is not working properly, if it has been dropped, damaged, or dropped into water while plugged in. For assistance call 1-800-243-3050.

4. Clipper can be rinsed under running tap water. Do not operate clipper until fully dried.

5. Keep the clipper, cord and any attachments away from heated surfaces.

6. Never drop or insert any object into any opening.

7. Do not operate, charge or plug in clipper outdoors or where aerosol (spray) products are being used or where oxygen is being administered.

8. Always check cutters, cutting unit, foil and combs before using the clipper. Do not use the clipper if cutters, cutting unit, foil or combs are damaged, as injury may occur.

9. Always attach plug to clipper first, then to outlet.To disconnect, turn on/off switch to “OFF” position, then remove plug from outlet.

10. To prevent possible damage to the cord, do not wrap cord around the clipper.

11. Never put clipper in direct sunlight or store at a temperature above 140°F.

12. This clipper is for use on human hair only. Do not use this clipper for any other purpose.

13. Always store your clipper, attachments and power plug in a moisture-free area. Make sure the cord is disconnected from the clipper.

14. Only use the power plug and other accessories supplied with the appliance.

SAVETHESE

INSTRUCTIONS

IMPORTANT: The power plug contains a transformer. Do not cut off the power plug to replace it with another plug as this will cause a hazardous condition.

Registration

Congratulations on your purchase and welcome to Philips Norelco!

To fully benefit from the support that Philips Norelco offers, register your product at www.norelco.com/register

Features

A Cutting Element B 180° Rotating Head C Hair Length Setting Adjustment Ring D ON/OFF Button E Socket for Appliance Plug F Battery Light G Regular Comb H Hair Length Setting Indicator I Precision Comb

J Protection Cap

K Shaving Head L Adapter M Cleaning Brush N Storage Pouch

Full Two-Year Warranty 45-Day Money-Back Guarantee

This symbol indicates that the Clipper can be rinsed under running tap water.

Put It To The Test

Like many new products, your Philips Norelco Hair Clipper may take a little getting used to. If you are using an electric Clipper for the first time, or if you’ve been using a different brand, take the time to acquaint yourself with your new Hair Clipper

Your Hair Clipper features a 180° pivoting head to comfortably clip even hard-to-reach areas of your head.

Throw your scissors away and put your new

Hair Clipper to the test. We guarantee precise, professional results or Philips Norelco will refund you the full purchase price as long as the request is received within 45 days of purchase.

To Charge/Recharge

I Fully charge Clipper before using for the first

time or after non-use for a long period of time.

► Charging, recharging, or using Clipper at

temperatures below 40°F or higher than 95°F adversely affects lifespan of the battery.

► If the appliance is subjected to a major change

in temperature, pressure or humidity, let the clipper acclimatize for 30 minutes before using.

► Do not charge/recharge or use Clipper corded

until fully dried.

Be certain Clipper is OFF.

D Slide the selected comb into the guiding

Make sure the comb attachment locks properly

into position.

Do not turn the length setting adjustment ring

beyond the highest hair length setting. B The arrowhead on the Clipper indicates When you are clipping for the first time, start

at the maximum clipping length setting (#5) of the regular comb to familiarize yourself with the appliance and prevent accidentally trimming hairs too short. As you become familiar with the settings, adjust the Hair Length Selector to desired trimming length.

Table 1 Precision and Regular Combs

D Insert the appliance plug directly into

the Clipper and plug the adapter into any 120V AC outlet (Fig. 1). Use only the cord provided.

The Battery Light on the appliance will blink white to indicate the Clipper is charging (Fig. 2).

k It will take approximately 1 hour to fully

charge the Clipper for a cordless clipping time of up to 60 minutes.

D After the Clipper is fully charged, the

battery light will light up continuously.

NOTE: After 30 minutes the battery light goes

out. H Disconnect the cord and unplug from

electrical outlet.

Corded Hair Clipping

► Only use the Clipper corded when the battery

is empty.

► Clipper does not recharge during corded

clipping.

n Connect cord provided to Clipper (Fig. 1)

and plug Clipper into electrical outlet.

WM If battery is completely empty, wait a few

minutes before turning Clipper ON.

TIP: Use different settings to create a natural and smooth transition between various hair lengths from your neckline to the top of your head (Fig. 7).

► At the starting clipping position of 0° (pointing

Always adjust the position of the cutting element by turning the rotating head. Do not turn the cutting element or the comb attachment.

B The rotating head allows you to hold and use

Do not turn the rotating head more than 90° to the left or right.

B Press the ON/OFF button to turn on the

□ Make sure that the flat part of the comb is

D Press ON/OFF button ON to begin clipping.

Q Turn Clipper OFF and unplug.

B Since all hairs do not grow in the same

Cordless Hair Clipping

n Charge according to directions. Unplug

Clipper from outlet and remove cord. H Press ON/OFF button ON to begin clipping. Q If the charge runs low while clipping, the

Battery Light will blink orange. Q If the charge runs out while clipping, simply

connect cord provided to Clipper and outlet

to continue clipping.

Hair Clipping

I Use this Clipper for its intended household

use as described in this manual.

► If you are clipping someone else's hair, make

sure that the head of the person is at the same level as your chest so that all parts of his/her

head are clearly visible and within easy reach. I Only use the appliance on clean, dry hair. ► Do not use on freshly washed hair. ► Before you begin,comb the hair in the direction

of growth (Fig. 3). ► To achieve optimal clipping results, always move

the appliance slowly through the hair against

the direction of hair growth.

Clipping with comb attachment

Be certain the Clipper is in the OFF position.

EE Turn the Clipper off regularly during clipping

When you remove the comb, the selected setting does not change.

TIP:Write down the settings you have used to create a certain hairstyle as a reminder for future clipping sessions.

grooves on both sides of the Clipper rotating

head and push until you hear it ‘click’ into place (Fig. 5).

Turn the Hair Length Setting Adjustment Ring

to set the comb to the desired setting (Fig.

6). See Table 1 for settings.

which setting has been selected.

Precision Comb Barber Remaining

Setting Hair Length

•

3/64 in./1 mm

forward), turn the rotating head 45’ or 90° to the left or right to adjust the position of the cutting element to the part of your head you are clipping (Fig. 8).

1/16 in./1.5mm

•

5/64 in72mm

•

3/32 in./2.5mm

Using the rotating head

desired clipping position. At each position you will hear a ‘click’ (Fig. 9).

the Clipper like a styling comb (Fig. 10).

appliance.

always in full contact with the scalp to obtain an even result.

direction, move the Clipper slowly over the crown from different directions (i.e. upwards, downwards and across) to achieve an even

result (Fig. 11).

Always move the Clipper slowly against the direction of hair growth.

ensure that all hair that should be cut has

been cut.

As you clip different areas of your head, adjust the position of the swivel head so that the rotating head position is most comfortable for you.

For best results with curly, sparse or long

hair, use a styling comb to guide the hair

towards the Clipper.

and remove the hair comb to blow and/or shake out hair that has accumulated.

Contouring without a comb attachment

1/8 ¡n./3mm

Turn the rotating head left or right to the

Make overlapping passes over the head to

Reguiar Comb Barber Remaining

Setting Hair Length

•

#2 9/32 in/7mm #3

•

#4 #5

1/8 in73mm

3/16 in./5mm

3/8 In79mm

7/16 in711mm

1/2 in713mm 5/8 in715mm

u Select the comb attachment depending on

the desired hair length.The table shows the remaining hair length after clipping at the different settings of the precision or regular

comb. The remaining hair length is also indicated on each comb (Fig. 4):

- Precision comb: 1-3mm (3/64 - 1/8 in.)

- Regular comb: 3-15mm (1/8 - 5/8 in.)

► Use the Clipper without a comb attachment to

clip very close to the skin (1/32 in/0.5mm).

► Be careful when you are clipping without a

comb as when the Clipper is turned on it will remove every hair it touches.

Remove the comb by pulling it off the swivel

head (Fig. 12).

Never pull at the flexible top of the comb. Always

pull at the bottom part.

D To contour the hairline around the ears,

comb the hair ends over the ears.

a Press the ON/OFF Button to turn on the

appliance.

D Tilt the Clipper in such a way that only one

edge of the cuttiing element touches the hair ends. Be careful not to trim too much. The hairline should be close to the ear (Fig. 13).

B To contour the neckline and the sideburns,

turn the Clipper and make downward strokes (Fig. 14).

NOTE: Move the Clipper slowly and smoothly.

Simply follow the natural hairline.

Cleaning the Shaving Head

O Turn off the Clipper and disconnect from the

electrical outlet.

a Press the release buttons on the shaving head

and remove the shaving foil from the shaving head (Fig. 24).

B Rinse the shaving head and shaving foil under

the tap (Fig. 25).

NOTE:To dean the shaving head with the cleaning brush, brush the inside and outside of the shaving head and the outside of the shaving foil.To remove cut hairs from the inside of the shaving foil, tap the bottom of the shaving foil gently on a flat surface.

PHILIPS

^NORELCO

Headgroom Pro

Q Adjust the position of the rotating head to

make contouring easier. Shaving

TIP: Shaving is easier when the hairs are shorter than 1mm. If the hairs are longer than 1mm, use the cutting element without the comb to pre<ut hairs to the shortest setting.

D Turn off Clipper. H Pull the comb off the rotating head (Fig. 12). H Press the release buttons (1) and remove

the cutting unit from the handle (2) (Fig. 15).

D Attach the shaving head by pressing it onto

the appliance.You will hear a ‘click’ (Fig. 16).

Make sure that the shaving head locks into position properly.

a Remove the protection cap from the shaving

head (Fig. 17).

If the shaving head foil shows signs of wear or damage, do not use as injury may occur Do not use the shaving head until foil has been replaced.

n Adjust the position of the rotating head to

make shaving easier.You can do this before and/or during use (Fig. 18).

Q Place the shaving head on your scalp and

start shaving (Fig. 19).

NOTE: Make sure that the shaving foil is always m full contact with your scalp.

Cleaning

I Clean the Clipper after each use.

I Always switch Clipper OFF, unplug and remove

power supply cord from Clipper before cleaning.

I Do not use compressed air, abrasive cleaning

agents, scourers or aggressive liquids such as gasoline, acetone or ethereal oils to clean the Clipper and attachments.

I Never clean, replace or remove Clipper

attachments with motor ON.

I Do not apply pressure to shaving head. Do not

touch foil with hard objects as this may dent or damage foil or cutters. If damage occurs, replace damaged parts.

I Do not use Clipper if foil, cutter or cutting

element are damaged or broken as injury may occur.

I Use a soft, dry cloth to clean Clipper handle.

During Use:

I If cut hairs have accumulated in the comb

area, remove hairs by shaking, blowing or using cleaning brush provided.

Cleaning the Cutting Element and Combs After Each Use:

D Make sure the Clipper is switched OFF

and disconnected from the electrical outlet. a Remove any comb attachment (Fig. 12). B Blow and/or shake out any hair that may

have accumulated in the comb. □ Rinse the comb under the tap or clean it

with the cleaning brush supplied.

H Apply pressure to the center of the cutting

element with your thumb (1) until it releases from the rotating head (2) (Fig. 20).

Be careful that the cutting element does not fall to

the floor

Clean the cutting element under the tap or with the brush supplied (Fig. 21).

Make sure the cutting element is thoroughly dry

before reattaching to Clipper

Clean the inside of the rotating head under the

tap or with the brush supplied (Fig. 22).

Clean the handle and the adapter with the cleaning brush supplied or with a dry cloth.

D Insert the notch of the cutting element into

the slot on the rotating head and push until the cutting element‘clicks’ into place (Fig. 23).

□ Press the shaving foil back into the shaving

head (Fig. 26).

Replacing the Shaving Foil Head

► If the shaving foil and cutters are worn or

damaged, do not continue using the Clipper. Replace the shaving foil and cutters immediately.

► It is recommended that you replace your

shaving foil and cutters once a year.

IA worn or damaged shaving foil or cutters

should only be replaced with an original Philips Norelco shaving foil, model QC5500, which is available on the Philips Norelco website, www.philips.com/support or call

I -800-243-3050 for assistance.

► The foil is a precision part. Handle with care. D Turn off the Clipper and disconnect it

from the electrical outlet.

a Press the release buttons on the shaving head

and remove the shaving foil from the shaving head (Fig. 24).

H Remove the retaining frame from the old

shaving foil (Fig. 27).

Q Place the retaining frame on the new shaving

foil (Fig. 28).

Remove the old shaving cutters (Fig. 29).

Place the new cutters on the shaving head. You will hear a ‘click’ (Fig. 30).

Q Press the shaving foil back into the shaving

head (Fig. 26).

This Clipper has no other user-serviceable parts.

For assistance call 1 -800-243-3050.

Assistance

For assistance, visit our website:

www.philips.com/support or call toll free: 1-800-243-3050

Online information is available 24 hours a day, 7 days a week.

Storage

k Be sure Clipper is turned OFF. Remove cord

from outlet and Clipper before storing in a safe, dry location where it will not be crushed, banged, or subject to damage.

I Do not wrap cord around Clipper when

storing.

I Store cord in a safe location where it will not

be cut or damaged.

► Do not place or store Clipper where it can fall

or be pulled into a tub or sink, water or other liquid while plugged in.

Battery Removal

► This Philips Norelco Clipper contains a

rechargeable Lithium-Ion battery which must be disposed of properly (Fig. 31 ).

► Battery may only be removed when Clipper is

to be discarded.

I For assistance, visit our website,

www.philips.com/support or call toll free; 1-800-243-3050

D Unplug electrical cord from outlet and

Clipper before dismantling Clipper.

Q Allow Clipper to run until the battery is

empty/depleted. Q Turn Clipper OFF. Q Remove any comb attachment.

Remove the upper housing part of the

Clipper (Fig. 32).

Use a screwdriver to open the inner body

of the Clipper. Q Use a screwdriver to remove the battery

from the Clipper (Fig. 33).

QC5580

Rechargeable Cordless/Cord

Always here to help you

www.norelco.com/register

4222 002 8312 2

Cut the wires with household scissors.

B Do not attempt to replace battery. Insulate

battery ends by covering with tape and/or place battery in a small plastic bag.

EQ Discard your Clipper. Do not attempt to

plug electrical cord into the outlet or recharge the Clipper after the battery has been removed.

Contact your local town or city officials for battery disposal information or call 1 -800-8-BATTERY or battery drop-off locations.

Full Two-Year Warranty

Philips Electronics North America Corporation warrants eadi new Philips

Norelco product. Model QC5580 (except foil, cutters and combs) against defects in materials or workmanship for a period of two years from the date of purchase, and agrees to repair or replace any defective produa

Vifithout cn.irjje

IMPORTANT: This warranty does not cover damage resulting from

accident, misuse or abuse, lack of reasonable care, the affixing of any attachment not provided with the product or loss of parts or subjecting the product to any but the specific voltage.* Use of unauthorized replacement parts will void this warranty.

PHILIPS ELECTRONICS NORTH AMERICA CORPORATION WILL NOT PAY FOR WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZEO REPAIR SERVICE AND WILL NOT REIMBURSE THE CONSUMER FOR DAMAGE RESULTING FROM WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZED REPAIR SERVICE. NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL. INCIDENTAL OR CONSEQUENTIAL DAMAGES.

In order to obtain warranty service, simply go to www.philips.com/ norelco or call 1-800-243-3050 for assistance. It is suggested that for your protection you return shipments of product by insured mail, insurance prepaid. Damage occurring during shipnnent is not covered by this warranty NOTE: No other warranty, written or oral, is authorized by Philips Electronics North America Corporation. This warranty gives you specific legal nghts. and you may also have oUier rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion and limitations nnay not apply to you.

•Read enclosed instructions carefully.

Manufactured for: Philips Consumer Lifestyle A Divisiw of Philips Electronics Nortii Amenca Corporation RO. Box 10313. Stamford. CT 06904

This symbol on the product's nameplate means it is

usTto listed by Underwnters' Laboratories. Inc.

Noieko is a Registered Trademark of Philips Electronics North America Corporation.

PHILIPS IS a Registered Trademark of KomnWi)ke Philips ElectronKS N.V.

www.rbrc.com for

PHILIPS

^NORELCO

45-DAY MONEY-

BACK GUARANTEE

If you are not fully satisfied with your Philips Norelco Clipper send the product back and we’ll refund you the full purchase price.

The Clipper must be shipped prepaid by insured mail, insurance prepaid, have the original sales receipt, indicating purchase price and date of purchase, and the money-back guarantee return authorization form enclosed. We cannot be responsible for lost mail. The Clipper must be postmarked no later than 4S days after the date of purchase. Philips Norelco reserves the right to verify the purchase price of the product and limit refunds not to exceed suggested retail price.

To obtain money-back guarantee return authorization form, call 1-800-243-3050 for assistance.

Delivery of refund check will occur 6-8 weeks AFTER receipt of returned product.