QC5570
1
2
3
4
5
6
11
13
10
12
7
9
8
empty page before TOC
English 6
简体中文
20
English
6
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benefit from the support that
Philips offers, register your product at
www.philips.com/welcome.
Your new Philips hair clipper with new ergonomic
design and 180º adjustable cutting element allows
you to clip your own hair easily. You can move the
clipper over all areas of your head as easily as
running your fingers through your hair. To enjoy
using the hair clipper, we advise you to read the
following information.
General description (Fig. 1)
1 Cutting element
2 Swivel head
3 Length setting adjustment ring
4 On/off button
5 Socket for small plug
6 Battery charge indicator
7 Precision comb attachment
8 Length setting indicator
9 Regular comb attachment
10 Supply unit
11 Small plug
12 Cleaning brush
13 Oil
Important safety information
Read this important information carefully before
you use the appliance and its accessories and save
it for future reference. The accessories supplied
may vary for different products.
English
Danger
Warning
English
- Keep the supply unit dry.
- To charge the battery, only use the detachable
supply unit (HQ8505) provided with the
appliance.
- The supply unit contains a transformer. Do not
cut off the supply unit to replace it with another
plug, as this causes a hazardous situation.
- This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Children
shall not play with the appliance. Cleaning and
user maintenance shall not be made by
children without supervision.
- Always unplug the appliance before you clean it
under the tap.
- Always check the appliance before you use it.
Do not use the appliance if it is damaged, as
this may cause injury. Always replace a
damaged part with one of the original type.
- This appliance contains batteries that are nonreplaceable.
- Do not open the appliance to replace the
rechargeable battery.
7
English
8
Caution
- Never immerse the charging stand in water and
do not rinse it under the tap.
- Never immerse the appliance in water. Do not
use the appliance in the bath or shower.
- Never use water hotter than 60°C to rinse the
appliance.
- Only use this appliance for its intended purpose
as shown in the user manual.
- For hygienic reasons, the appliance should only
be used by one person.
- Do not use the supply unit in or near wall
sockets that contain an electric air freshener to
prevent irreparable damage to the supply unit.
- Never use compressed air, scouring pads,
abrasive cleaning agents or aggressive liquids
such as petrol or acetone to clean the
appliance.
Electromagnetic fields (EMF)
This Philips appliance complies with all applicable
standards and regulations regarding exposure to
electromagnetic fields.
General
- This appliance can be safely cleaned under the
tap.
- The supply unit is suitable for mains voltages
ranging from 100 to 240 volts.
- The supply unit transforms 100-240 volts to a
safe low voltage of less than 24 volts.
Charging
Charge the appliance before you use it for the first
time and when the battery status indicator
indicates that the battery is almost empty (see
'Battery charge indicator').
English
Note: Charge the appliance for at least 1 hour
before you use it for the first time or after a long
period of non-use.
Charging takes approx. 1 hour. A fully charged
appliance has a operating timeof up to 60
minutes.
Note: This appliance can be used cordless or
directly from the wall socket.
Battery charge indicator
- When the battery is almost empty, the battery
charge indicator flashes orange.
- When the appliance is charging, the battery
charge indicator on the appliance flashes white.
- When the battery is fully charged, the battery
charge indicator lights up white continuously.
Note: When the battery is full, the battery charge
indicator switches off automatically after approx.
30 minutes.
Charging with the supply unit
1 Put the small plug in the appliance and put the
supply unit in the wall socket.
The battery charge indicator indicates that the
appliance is charging (see 'Battery charge
indicator').
2 After charging, remove the supply unit from the
wall socket and pull the small plug out of the
appliance.
Note: When the battery is full, the battery charge
indicator switches off automatically after approx.
30 minutes.
Optimizing the lifetime of the rechargeable battery
Discharge the rechargeable battery completely
twice
a year by letting the motor run until it stops. Then
9
1
2
English
10
fully recharge the battery.
Before first use
1 Pull the front of the cutting element upwards
and remove the cutting element from the
appliance.
2 Turn the cutting element and lubricate the
three points indicated with oil from the oil
bottle supplied.
Using the appliance
This appliance can be used cordless or directly
from the wall socket.
Preparing for use
Make sure your hair is clean and dry.
1 Comb your hair with a styling comb in the
direction of hair growth.
Hairclipping tips
- We advise you to start clipping at the highest
setting of the regular comb attachment and to
reduce the setting gradually.
- To clip most effectively, move the appliance
against the hair growth direction.
- Since all hair does not grow in the same
45˚
180°
90˚
0˚
45˚
90˚
direction, you need to move the appliance in
different directions (upwards, downwards and
across).
- Make sure that the flat part of the comb
attachment is always fully in contact with the
scalp to obtain an even result.
- Write down the settings you use to create a
certain hairstyle as a reminder for future
clipping sessions.
Using the swivel head
From its starting position of 0° (pointing forwards),
you can turn the swivel head 45° or 90° to the left
or right. This enables you to adjust the position of
the cutting element to the part of your head that
you are clipping. This makes it much easier to clip
your own hair.
1 To set the cutting element to the desired
position, turn the swivel head (‘click’).
Note: Always adjust the position of the cutting
element by turning the swivel head. Do not turn
the cutting element or the comb attachment.
Note: Do not turn the swivel head more than
90° to the left or right.
The swivel head allows you to hold and use the
appliance like a styling comb.
English
11
– 3 mm
– 5 mm
– 7 mm
7
5
2
1
English
12
Hair clipping with comb
1 Insert the edge of the comb attachment into
the swivel head.
Make sure the comb attachment locks into
position properly.
Note: The length settings are indicated on the
comb attachment.
2 Turn the length setting adjustment ring to set
the comb attachment to the desired setting.
The arrowhead on the appliance indicates
which setting you have selected.
Tip: Use different settings to create a natural
and smooth transition between the various hair
lengths from your neckline to the top of your
head.
Do not turn the length setting adjustment ring
beyond the highest setting.
3 Turn the swivel head to the position that is
most comfortable for your arm when you clip
the different parts of your head (see 'Using the
swivel head ').
4 Press the on/off button to switch on the
appliance.
QC5570: Press the button briefly.
QC5580: Press the button for 2 seconds.
5 Move the clipper through the hair slowly.
6 Regularly remove cut hair from the comb
attachment.
If a lot of hair has accumulated in the comb
attachment, remove the comb attachment from
the appliance and blow and/or shake the hair
out of it. When you remove the comb
attachment, the selected setting does not
change.
Contouring without comb
You can use the appliance without comb
attachment to clip your hair very close to the skin
(0,5mm) or to contour the neckline and the area
around the ears.
Be careful when you clip without comb
attachment because the cutting element removes
every hair it touches.
1 Pull the comb attachment off the swivel head.
Never pull at the flexible top of the comb
attachment. Always pull at the bottom part.
2 Comb the hair ends over the ears before you
start to contour the hairline.
3 Press the on/off button to switch on the
appliance.
4 When you shape the contours around the ears,
tilt the appliance in such a way that only one
edge of the cutting element touches the hair
ends.
English
13
English
14
5 To contour the neckline and the sideburns, turn
the appliance and make downward strokes.
Note: Move the appliance slowly and smoothly.
Just follow the natural hairline.
6 Adjust the position of the swivel head to make
contouring easier (see 'Using the swivel head ').
Cleaning and maintenance
Regular cleaning guarantees better grooming
results.
Never clean, remove or replace a shaving or
cutting unit while the appliance is switched on.
Always check if the water is too hot, to prevent
burning your hands.
Never dry cutting units or shaving foils with a
towel or tissue, as this may cause damage.
Never use compressed air, scouring pads,
abrasive cleaning agents or aggressive liquids
such as petrol or acetone to clean the
appliance.
Clean the appliance every time you have used it by
rinsing it under the tap or with the cleaning brush
supplied.
Always unplug the appliance before you clean it
under the tap.
Be careful that the cutting element does not fall
on the floor.
1 Switch off the appliance and disconnect it from
the mains.
2 Remove the comb attachment.
3 Rinse the comb attachment under the tap or
clean it with the cleaning brush supplied.
1
2
4 Place your thumb in the center of the round
1
2
1
2
side of the cutting element and your index
finger on the teeth of the cutting element. Use
your index finger to lift the cutting element from
the swivel head.
5 Rinse the cutting element under the tap or
clean it with the cleaning brush supplied.
6 Rinse the inside of the appliance under the tap
or clean it with the cleaning brush supplied.
7 Insert the lug of the cutting element into the
slot and push the cutting element back onto
the swivel head.
Lubricate the cutting element
Lubricate the cutting element every 3 months with
oil form the bottle supplied with the appliance.
1 Pull the front of the cutting element upwards
and remove the cutting element from the
appliance.
English
15
English
16
2 Turn the cutting element and lubricate the
three points indicated.
Storage
1 Switch off the appliance and disconnect it from
the mains.
2 Store the appliance and its accessories in the
storage pouch supplied.
Ordering accessories
To buy accessories or spare parts, visit
www.philips.com/parts-and-accessories or go to
your Philips dealer. You can also contact the
Philips Consumer Care Center in your country (see
the international warranty leaflet for contact
details).
Recycling
- Do not throw away the product with the normal
household waste at the end of its life, but hand
it in at an official collection point for recycling.
By doing this, you help to preserve the
environment.
- This product contains a built-in rechargeable
battery which shall not be disposed of with
normal household waste. Please take your
product to an official collection point or a
Philips service center to have a professional
remove the rechargeable battery.
- Follow your country’s rules for the separate
collection of electrical and electronic products
and rechargeable batteries. Correct disposal
helps prevent negative consequences for the
environment and human health.
Removing the rechargeable battery
Only remove the rechargeable battery when
you discard the product. Before you remove
the battery, make sure that the product is
disconnected from the wall socket and that
the battery is completely empty.
Take any necessary safety precautions
when you handle tools to open the product
and when you dispose of the rechargeable
battery.
1 Disconnect the appliance from the mains and
let the appliance run until the motor stops.
2 Remove the upper housing part of the
appliance.
3 Open the inner body with a screwdriver.
4 Use a screwdriver to remove the rechargeable
battery from the appliance.
5 Cut the wires with a pair of household scissors.
English
17
Troubleshooting
This chapter summarizes the most common
problems you could encounter with the appliance.
If you are unable to solve the problem with the
English
18
information below, visit www.philips.com/support
for a list of frequently asked questions or contact
the Consumer Care Center in your country.
Problem Possible cause Solution
The appliance
produces an
uneven cutting
result.
The appliance
does not work
when I switch it
on.
I do not know
how to attach the
comb
attachments to
the appliance.
The comb does not
touch the skin
when you move
the appliance
through the hair.
You only move the
appliance in one
direction.
The setting of the
comb has changed
during trimming.
The comb is not
assembled
correctly.
The cutting
performance
decreases when
the cutting unit and
the comb are dirty.
The appliance is
not connected to
the the wall socket.
Make sure the comb is
always fully in contact with
the skin when you move
the appliance through the
hair.
Because not all hairs grow
in the same direction,
move the appliance in
different directions
(upwards, downwards and
across).
Check the setting of the
comb. If you push the
appliance too hard onto
the scalp, you may
accidentally change the
setting of the comb.
Detach the comb and
reattach it.
Clean the cutting unit and
the comb.
Insert the small plug into
the appliance and put the
supply unit in the wall
socket.
To attach the comb
attachments, simply slide
them into the slot in the
appliance.
Problem Possible cause Solution
English
19
I do not know
how to change
the hair length
settings of the
comb
attachments.
One of the comb
attachments is
damaged
or worn.
Warranty and support
If you need information or support, please visit
www.philips.com/support or read the
international warranty leaflet.
Warranty restrictions
Cutting units are not covered by the terms of the
international warranty because they are subject to
wear.
You can change the hair
length settings of the comb
attachments with the
length
setting adjustment ring on
the appliance. Turn the ring
to set the comb
attachment to the desired
setting. See chapter ‘Using
the appliance’, section
‘Hair clipping with comb’
Do not use the comb
attachment anymore.
Replace it with an
attachment or comb of the
original type. You can
obtain a replacement
comb attachment from
your local Philips dealer or
you can visit
www.philips.com/ shop.
For more information you
can contact the Consumer
Care
20
简体中文
简介
感谢您的惠顾，欢迎光临飞利浦！ 为了让
您能充分享受飞利浦提供的支持，请在
www.philips.com/welcome 上注册您的产
品。
您新购买的飞利浦理发器采用全新人体工
程学设计和 180° 可调节修剪部件，使您
可以轻松为自己修剪头发。 您可以将理发
器在自己的整个头部移动，就好像手指划
过头发一样轻松。 要充分享受理发器的便
利，建议您阅读以下信息。
基本说明（图 1）
1 修剪部件
2 旋转头
3 长度设置调整环
4 开/关按钮
5 小插头插口
6 电池充电指示灯
7 精密梳齿附件
8 长度调校指示器
9 常规梳齿附件
10电源部件
11小插头
12清洁刷
13油
简体中文
重要安全信息
危险
警告
简体中文
使用本产品及其附件之前，请仔细阅读本
重要信息，并妥善保管以供日后参考。 随
附的附件可能因产品而异。
- 保持电源部件干燥。
- 警告符号注释： 禁止在打开的水龙头下
进行清洗。
- 要给电池充电，请仅使用产品随附的可
拆卸电源部件 (HQ8505)。
- 电源部件中包含一个变压器。 请勿自行
更换电源部件的插头，否则将导致严重
后果。
- 本产品也可以由 8 岁或以上年龄的儿童
以及肢体不健全、感觉或精神上有障碍
或缺乏相关经验和知识的人士使用，但
前提是有人对他们使用本产品进行监督
或指导，以确保他们安全使用，并且让
他们明白相关的危害。 切勿让儿童玩弄
本产品。 不要让儿童在无人监督的情况
下对本产品进行清洁和保养。
- 手持部分与电源软线分开后，才能在水
中清洗手持部分。
21
22
简体中文
警告
电磁场 (EMF)
- 使用前，请务必检查产品。 请勿使用损
坏的产品，否则可能对人体造成伤害。
请务必用原装型号更换损坏的部件。
- 本产品包含的电池不可更换。
- 切勿拆开本产品更换充电电池。
- 切勿将充电座浸入水中，也不要在自来
水龙头下冲洗。
- 切勿将产品浸入水中。 请勿在洗澡或淋
浴时使用本产品。
- 切勿使用温度高于 60°C 的热水冲洗
本产品。
- 只能将本产品用于用户手册中所示的原
定用途。
- 出于卫生的目的，本产品只能供一个人
使用。
- 请勿在包含电动空气清新器的墙壁插座
上或其周围使用电源部件，以免电源部
件受到不可修复的损坏。
- 切勿使用压缩气体、钢丝绒、研磨性清
洁剂或腐蚀性液体（例如汽油或丙酮）
来清洁产品。
本 Philips 产品符合所有有关暴露于电磁
场的适用标准和法规。
概述
充电
电池充电指示灯
简体中文
- 该产品可放心在水龙头下清洗。
- 符号注释：适合用在打开的水龙头下进
行清洗。
- 电源部件适合在 100 - 240 伏的电源电
压下工作。
- 该电源部件可将 100-240 伏的电压转换
为 24 伏以下的安全低电压。
第一次使用本产品之前，以及当电池状态
指示灯指示电池电量快要耗尽 (请参见 '电
池充电指示灯')时，请为本产品充电。
注意： 首次使用前或长时间不用之后，请
为产品至少充电 1 小时。
充电约需 1 小时。充满电的产品最长可使
用 60 分钟。
注意： 本产品可以不接电源或直接连在插
座上使用。
- 当电池的电量几乎耗尽时，电池充电指
示灯会呈橙色闪烁。
- 产品充电时，其电池充电指示灯呈白色
闪烁。
- 电池充满电后，电池充电指示灯将呈白
色持续亮起。
注意： 电池充满电后，电池充电指示灯将
在大约 30 分钟后自动关闭。
23
1
2
24
简体中文
使用电源部件充电
1 将小插头插入本产品，然后将电源部件
2 充电之后，从电源插座上拔下电源部
注意： 电池充满电后，电池充电指示灯将
在大约 30 分钟后自动关闭。
优化充电电池寿命
每年将充电电池彻底放电两次，
方法是让马达一直转动，直到不再转为
止。 然后
将电池再次完全充电。
首次使用之前
1 将修剪部件前端向上拉，然后从产品上
插入电源插座。
电池充电指示灯指示产品正在充电 (请
参见 '电池充电指示灯')。
件，并从本产品上拔下小插头。
取下修剪部件。
2 转动修剪部件，用随附油瓶中的油润滑
所示的三个位置。
使用本产品
45˚
180°
90˚
0˚
45˚
90˚
使用准备
头发修剪提示
使用旋转头
简体中文
25
本产品可以不接电源或直接连在插座上使
用。
确保头发清洁干燥。
1 使用定型梳沿头发生长的方向梳理头
发。
- 建议您从常规梳齿附件的最高设置开始
修剪，然后逐渐缩短设置。
- 要获得最大修剪效率，请沿头发生长的
反方向移动本产品。
- 因为头发不会全部以相同的方向生长，
您需要以不同的方向移动产品（向上、
向下或交叉）。
- 确保梳齿附件的扁平部分完全接触到头
皮，以获得均匀的修剪效果。
- 记下您使用的设置，用作以后剪发过程
中打造某种发型的参考。
您可以将旋转头从开始位置 0°（指向前
方）向左或向右旋转 45° 或 90°。 您可
以通过这种方法调整修剪部件，以贴合待
– 3 mm
– 5 mm
– 7 mm
26
简体中文
修剪头发部位的头部轮廓。 这使您可以更
轻松地为自己理发。
1 要将修剪部件设置到所需位置，请转动
旋转头（可听到“咔哒”一声）。
注意： 始终通过转动旋转头调整修剪部
件的位置。 请勿转动修剪部件或梳齿附
件。
注意： 请勿向左或向右转动旋转头超过
90°。
您可以像握持定型梳一样握住旋转头来
使用本产品。
使用修剪梳修剪头发
1 将梳齿附件的边缘插入旋转头。
确保梳齿附件正确锁定到位。
注意： 梳齿附件上指示长度设置。
7
5
2
1
简体中文
2 旋转长度设置调整环，将梳齿附件设为
所需设置。
产品上的箭头表示您选择的设置。
提示： 使用不同设置在从颈部到头顶的
各种头发长度之间实现自然顺利的过
渡。
切勿将长度设置调整环转到最高设置之
外。
3 在修剪不同位置的头发 (请参见 '使用旋
转头 ')时，可以将旋转头转动到您的手
臂感觉最舒服的位置。
4 按开/关按钮启动产品。
QC5570： 短暂地按下按钮。
QC5580： 按住按钮 2 秒钟。
5 将理发器在头发上缓慢移动。
6 定期清除梳齿附件中剪下的头发。
如果梳齿附件中积聚了许多头发，请先
取下梳齿附件，吹去和/或抖掉梳齿附件
上的头发。 取出梳齿附件时，所选的设
置不会改变。
27
不用梳齿的情况下修剪轮廓
即使没有梳齿附件，您也可以使用理发器
以非常贴近头皮的距离（0.5 毫米）或紧
28
简体中文
密贴合颈部周围和双耳附近的皮肤修剪头
发。
由于修剪部件会去除接触到的每一根头
发，因此在没有梳齿附件修剪头发时要小
心。
1 将梳齿附件从旋转头拉出。
切勿拔扯梳齿附件容易变形的顶部。 请
务必拉拔底部。
2 在开始紧贴双耳附近的发线修剪头发之
前，请梳理耳朵上方的发梢。
3 按开/关按钮启动产品。
4 修整耳朵周围的轮廓时，倾斜产品，使
修剪部件只有一边接触发梢。
5 要紧贴颈部周围和鬓角轮廓，请转动产
品并向下修剪。
注意： 缓慢、流畅地移动产品。 只需
顺着自然生长的发际线。
6 调整旋转头的位置，使修剪轮廓更容易
(请参见 '使用旋转头 ')。
清洁和保养
为保证更好的修剪效果，请定期清洗剃
毛刀。
1
2
简体中文
切勿在产品开启时清洗、拆卸或更换剃
毛或修剪部件。
切记先检查水温是否太高，以防烫手。
切勿使用毛巾或纸巾擦干修剪部件或剃
毛刀网，因为有可能造成损坏。
切勿使用压缩气体、钢丝绒、研磨性清
洁剂或腐蚀性液体（例如汽油或丙酮）
清洁本产品。
每次用完产品后，请在水龙头下冲洗产品
或用随附的清洁刷进行清洁。
在自来水龙头下清洗剃须刀之前，务必拔
掉其电源插头。
小心不要让修剪部件掉落在地板上。
1 关闭产品并断开电源。
2 取下发梳。
3 在水龙头下冲洗梳齿附件或用随附的清
洁刷进行清洁。
4 将拇指放在修剪部件的圆边中心，食指
放在修剪部件的齿上。 使用食指从旋转
头提起修剪部件。
29
1
2
1
2
30
简体中文
润滑修剪部件
5 在水龙头下冲洗修剪部件或用随附的清
洁刷进行清洁。
6 在水龙头下冲洗产品的内部或用随附的
清洁刷进行清洁。
7 将修剪部件的凸缘插入槽内，然后将修
剪部件推回旋转头。
每 3 个月用产品随附的油瓶中的油润滑一
次修剪部件。
1 将修剪部件前端向上拉，然后从产品上
取下修剪部件。
2 转动修剪部件并润滑所示的三个位置。
存放
订购配件
回收
简体中文
1 关闭产品并断开电源。
2 将产品及其附件存放在随附的存储袋
中。
如需购买附件或备件，请访问
www.philips.com/parts-and-accessories
或联系您的飞利浦经销商。 您还可以联系
所在国家/地区的飞利浦客户服务中心（请
参阅国际保修卡了解详细联系信息）。
- 弃置本产品时，请不要将其与一般生活
垃圾放在一起，应将其交给政府指定的
回收中心。 这样做将有利于环保。
- 此产品包含内置充电电池；请勿将充电
电池与一般生活垃圾一起弃置。 请您将
产品送到官方收集中心或飞利浦服务中
心，请专业人士移除充电电池。
- 遵循您的国家/地区有关分类回收电子电
气产品和充电电池的规定。 正确弃置产
品有助于避免对环境和人类健康造成不
良后果。
31
卸下充电电池
必须在丢弃本产品前拆下充电电池。 卸下
电池之前，请确保本产品与电源断开连接
并且电池电量已耗尽。
мȞġĈҴˀΙĀǩ؆Ӎߒʔ
ˌɫǩ؆
ĈҴˀΙ
(Pb)᰽(Hg)⬡(Cd)
ԣᲱ
(Cr (VI) )
Ġ⅑ԓ᧠
(PBB)
Ġ⅑ȕ᧠⓭
(PBDE)
PCB’s
מŪǗɢذ
X O O O O O
Electrical
contact pins
ǗˈǦ
X O O O O O
Power plug
Ǘ۷Ǽ
X O O O O O
X O O O O O
ǕȪϜ֪֙SJ/T 11364Āܪǭৠ뺯
OȪФ˽ĈҴˀΙć˽ˌɫǨĈߴΙࠒնġĀߒʔߴćGB/T 26572ܪǭĀՄʔđŘĪ뺯
XȪФ˽ĈҴˀΙψɺć˽ˌɫĀԚĂߴΙࠒնġĀߒʔɸŜGB/T 26572ܪǭĀՄʔđ뺯
Internal
metal parts
ʭˌɫ
32
简体中文
当您使用工具打开本产品时以及在您弃置
充电电池时，请采取必要的安全保护措
施。
1 断开产品电源并让产品继续运行，直到
马达停止。
2 去除产品的上顶盖部分。
3 使用螺丝刀打开产品内部主体。
4 使用螺丝刀从产品取下充电电池。
5 使用家用剪刀剪断电线。
- 该表格中所显示的“有害物质”在产品
正常使用情况下不会对人身和环境产生
任何伤害。
- 该表格中所显示的“有害物质”及其存
在的部件向消费者和回收处理从业者提
供相关物质的存在信息，有助于产品废
弃时的妥善处理。
故障处理方法
本章归纳了使用本产品时最常见的一些问
题。 如果您无法根据以下信息解决问题，
请访问 www.philips.com/support 查阅常
见问题列表，或联系您所在国家/地区的客
户服务中心。
问题 可能的原因 解决方法
简体中文
33
产品的修剪效
果不均匀。
产品在头发上推
动时没有触碰头
皮。
您只向一个方向
移动产品。
修剪过程中修剪
梳的设置有所更
改。
修剪梳组装不正
确。
修剪梳在头发上推动
时，请确保修剪梳可
始终与皮肤完全接
触。
由于并非所有头发都
向一个方向生长，请
朝不同方向移动产品
（向上、向下以及交
叉）。
检查修剪梳的设置。
如果您将产品过于用
力地按在头皮上，您
可能会意外更改修剪
梳的设置。
卸下修剪梳，重新安
装。
34
简体中文
问题 可能的原因 解决方法
启动产品后，
产品无法工
作。
我不知道如何
将梳齿附件连
接至产品。
我不知道如何
更改梳齿附件
的头发长度设
置。
其中一个梳齿
附件损坏
或磨损。
如果修剪部件和
修剪梳不干净，
修剪性能会下
降。
产品没有连接电
源插座。
清洁修剪部件和修剪
梳。
将充电插头插入产
品，然后将电源部件
插入电源插座。
要连接梳齿附件，只
需将其滑入产品的插
槽中即可。
您可使用产品上的长
度设置调整环
更改梳齿附件的头发
长度设置。 旋转调整
环，将梳齿附件设为
所需设置。 请参
阅“使用产品”一章
的“使用修剪梳修剪
头发”部分
切勿再使用梳齿附
件。 请使用原装型号
的附件或梳齿更换。
您可以从当地的飞利
浦经销商获得替换梳
齿附件，或访问
www.philips.
com/shop。 有关更多
信息，您可以联系飞
利浦客户服务
保修和支持
保修条款
简体中文
如需信息或支持，请访问
www.philips.com/support 或阅读国际保修
卡。
修剪部件不在国际保修条款的涵盖范围之
内，因为修剪部件属于易磨损物品。
35
36
简体中文
保留备用
发行日期: 11/9/2018
Empty page before back cover
© 2018 Koninklijke Philips N.V.
All rights reserved
保留所有权利
4222.002.8362.5 (11/9/2018)
> 75% 循环再造纸
保留备用
>75% recycled paper
>75% papier recyclé
Loading...