Congratulations on your purchase of Philips
Magnavox Universal Remote Control. Philips
Magnavox Universal Remotes let you replace a
broken or lost remote or combine more than one
remote into one.
This remote control operates the common features
of most but not all models and brands of IR
Infrared Controlled Video Equipment. This
remote may provide functions that are not
available on your equipment. Some functions of
your particular equipment (e.g. menu functions)
may not be controlled by this remote. In such
cases, use the original remote control for your
equipment. Please use this manual to become
familiar with your Philips Magnavox Universal
Remote. After you are familiar with your remote
the first thing you need to do is to install batteries
and setup your remote for your particular product
and brand.
Thank you for buying a Philips Magnavox remote
and we hope it will give you many years of
service.
32
Setup
Battery Installation
1. On the back of the remote,
push down on the tab and
lift the cover off.
2. Match the batteries to the
+ and - marks inside the
battery case, then insert 2
AAA Alkaline batteries.
3. Press the battery cover
back into place.
Battery Saver
Your remote automatically
times out if the buttons are
depressed more than 30
seconds. This will save your
batteries should your remote
get stuck in a place where the
buttons remain depressed
(e.g., between the sofa
cushions).
Power-On Default
The remote powers on in TV mode.
TV Volume/Mute Punch-Through
The TV Volume/Mute punch-through feature lets you
control the Volume and Mute function of your TV in any
mode programmed to be a VCR, DVD, or SAT device,
without needing to change to TV mode.
VCR/DVD Punch-Through
Punch-through to VCR and DVD mode is only allowed
in TV mode. SAT/DBS is dedicated for satellite mode.
Code Setup
The Code Search button is used to setup the remote.
You can either setup the remote using the code for your
brand of product, from the code tables, or you can
search through the library of codes until you find a
code that works for your product.
Code Saver
You will have up to 10 minutes to change the batteries
in your remote without losing codes you have
programmed. However, do not press any buttons until
batteries are installed in the remote. If buttons are
pressed without batteries in the remote, all codes will be
lost.
NOTE: You can store any kind of code under any mode
(except TV). I.E. you can store a DVD code under the
SAT key, or a TV code under the DVD key, etc.
However, you can only store TV codes under the TV
key.
VCR
VCR
VCRVCR
DVD
DVD
PIP
PIP
PIPPIP
TOGGLE/TITLE
TOGGLE/TITLE
TOGGLE/TITLETOGGLE/TITLE
DVDDVD
CHAN
CHAN
CHANCHAN
MUTE
MUTE
MUTEMUTE
CCCCHHHHAAAANNNN
POWER
POWER
POWERPOWER
SAT
SAT
SATSAT
++++
VV
VO
V
OO
OL
LL
L
++
PREV
PREV
PREVPREV
CHAN
CHAN
CHANCHAN
+
+
REPEAT
REPEAT
REPEATREPEAT
SUBTIT LE
SUBTIT LE
SUBTIT LESUBTIT LE
CCCCCCCC
Code Search.
CODE
CODE
CODECODE
SEARCH
SEARCH
SEARCHSEARCH
SLEEP
SLEEP
SLEEPSLEEP
TV
TV
TVTV
54
Button Functions
Some buttons on the remote might have functions that
are referred to by different names on the device you are
controlling. E.G. Prev. Ch. may be called RECALL, or
ENTER may be called DISPLAY. These differences
depend on the brand and model of your product. Also,
this remote can only operate features that exist on your
product. E.G., your product must be equipped with Prev.
Ch. ability for the Prev. Ch. button to operate this
feature.
MUTE Turns off
the TV sound
while the
picture remains.
TV, DVD/VCR,
SAT Selects
product to be
operated.
Code Search
For setup.
POWER Turns
product On or Off.
SLEEP Turns off the
TV after a period of 1
to 99 minutes.
PIP TV Picture-inPicture control.
NUMBERS
Enter numbers for direct
channel selection. Some
products require Enter to
be pressed after channel
selection.
ENTER
Used after direct
channel number
entry to immediately
change to the
selected channel.
INFO/Select
displays/selects
on-screen channel
information, etc.
MENU Access the
Menu functions of
the device you are
controlling.
TV
TV
TVTV
CODE
CODE
CODECODE
SEARCH
SEARCH
SEARCHSEARCH
SLEEP
SLEEP
SLEEPSLEEP
INFO/
INFO/
INFO/INFO/
SELECT
SELECT
SELECTSELECT
MENU
MENU
MENUMENU
SSSSCCCCAAAANNNN
OK
Selects menu items for the
device you are controlling.
Indicator light
Lights when any
button is pressed.
VCR
VCR
VCRVCR
DVD
DVD
DVDDVD
CHAN
CHAN
CHANCHAN
MUTE
MUTE
MUTEMUTE
CCCCHHHHAAAANNNN
POWER
POWER
POWERPOWER
PIP
PIP
PIPPIP
TOGGLE/TITLE
TOGGLE/TITLE
TOGGLE/TITLETOGGLE/TITLE
ENT ER
ENT ER
ENT EREN TER
OK
OK
OKOK
CHAPTER
CHAPTER
CHAPTERCH APTER
PLAY
PLAY
PLAYPLAY
REC
REC
STOP
STOPPAUSE
RECREC
STOPSTOP
SAT
SAT
SATSAT
++++
VV
VO
V
OO
OL
LL
L
++
+
+
INPUT
INPUT
INPUTINPUT
TV/VCR
TV/VCR
TV/VCRTV/VCR
QUI T
QUI T
QUI TQUIT
CCCCCCCC
GUI DE
GUI DE
GUI DEGUI DE
PREV
PREV
PREVPREV
CHAN
CHAN
CHANCHAN
REPEAT
REPEAT
REPEATREPEAT
SUBTIT LE
SUBTIT LE
SUBTIT LESUBTIT LE
++++
++++
SCAN
SCAN
SCANSCAN
PAUSE
PAUSEPAUS E
Button Functions, cont.
CHANNEL Up/
Down Changes
the channels.
TV
TV
TVTV
CODE
CODE
CODECODE
SEARCH
SEARCH
SEARCHSEARCH
SLEEP
SLEEP
SLEEPSLEEP
PIP
PIP
PIPPIP
TOGGLE/TITLE
TOGGLE/TITLE
TOGGLE/TITLETOGGLE/TITLE
ENT ER
ENT ER
ENT EREN TER
INFO/
INFO/
INFO/INFO/
SELECT
SELECT
SELECTSELECT
MENU
MENU
MENUMENU
SSSSCCCCAAAANNNN
REC
REC
RECREC
CHAPTER +/- controls DVD
track selection i.e. DVD Track
Skip Up/Down.
VOLUME Up/
Down Changes the
volume level of
the product,
normally the TV.
VCR
VCR
VCRVCR
DVD
DVD
DVDDVD
++++
CHAN
CHAN
CHANCHAN
VV
VO
V
OO
OL
LL
L
MUTE
MUTE
MUTEMUTE
++
+
+
CCCCHHHHAAAANNNN
POWER
POWER
POWERPOWER
INPUT
INPUT
INPUTINPUT
TV/VCR
TV/VCR
TV/VCRTV/VCR
OK
OK
OKOK
QUI T
QUI T
QUI TQUIT
++++
CHAPTER
CHAPTER
CHAPTERCH APTER
SCAN
SCAN
PLAY
PLAY
SCANSCAN
PLAYPL AY
STOP
STOPPAUSE
PAUSE
STOPSTOP
PAUSEPAUS E
CCCCCCCC
GUI DE
GUI DE
GUI DEGUI DE
++++
SAT
SAT
SATSAT
PREV
PREV
PREVPREV
CHAN
CHAN
CHANCHAN
REPEAT
REPEAT
REPEATREPEAT
SUBTIT LE
SUBTIT LE
SUBTIT LESUBTIT LE
Prev. Ch.
Returns to the
previously
selected channel,
or DVD repeat
toggle.
CC (Subtitle)
TV Closed
Caption (if your
TV has this
feature) or DVD
Subtitle toggle.
TOGGLE Swaps
TV PIP screens.
TITLE brings up
the DVD Title
Menu screen (in
DVD Mode).
Input
For some TVs,
press repeatedly
to select from
available viewing
sources (TV, VCR,
SAT, etc.).
GUIDE displays
on-screen
program guide.
QUIT Used to exit
menu functions.
PLAY, STOP, REW,
FF, PAUSE, REC
DVD/VCR control
buttons operate your
DVD/VCR even when
the remote is set to
operate the TV.
76
Advanced Button Functions
DVD
Scan+ and Scan- buttons control the speed of Fast
Forward and Reverse Playback respectively.
Chapter+ and Chapter- buttons respectively locate the
succeeding or preceding Chapters or Tracks on a disc.
Subtitle button brings up DVD Subtitle Menu for
Subtitle selection and display.
Repeat button performs DVD players “A-B Repeat” (or
RPT A.B) function for repeat play of current Chapter or
Track.
Info/Select button brings up DVD Display or Control
Menu for Chapter/Track/Title number, Time remaining/
elapsed indication, system information, etc.
Menu brings up the DVD disc Menu screen - use with
the Up, Down, Left & Right navigation buttons.
OK button is used for on-screen Menu selection. Note
some DVD players require the Play button to be used.
Quit button is used to Exit or Clear on-screen Menu
displays.
Title brings up the DVD Title Menu screen (in DVD
Mode).
Play button is used to start Disc playback and for Menu
selection on some DVD players.
Stop button stops Disc playback.
Pause button will pause Disc playback - press Play to
resume.
Note - in DVD Mode the INPUT button activates the
DVD Players SETUP Menu.
SAT
Guide button displays on-screen Satellite Channel
Guide.
Chapter+ and Chapter- buttons perform the “Page+”
and “Page-” function for on-screen Guide Menus used
by some Satellite systems.
Info/Select button brings up Satellite Display screen for
current Channel and system information.
Menu brings up the Satellite Menu screen - use with the
Up, Down, Left & Right navigation buttons.
OK button is used for on-screen Menu selection.
Quit button is used to Exit or Clear on-screen Menu
displays.
Input button performs the Satellite TV/SAT function.
TV/DVD Punch-Through
DVD/VCR Punch-through is automatically available in
TV mode, i.e. the 6 DVD keys (Play, Pause, Stop, FF,
Rewind, and Record) will punch-through to the device
programmed under DVD or VCR when in TV mode.
The INPUT button performs the TV/SAT switch
function when in SAT Mode.
The INPUT button performs the INPUT source switch
function when in TV Mode.
The INPUT button performs the DVD Setup function
when in DVD Mode.
The TV/VCR/INPUT button performs the TV/VCR
antenna switch function when in VCR Mode.
Misc.
SELECT means same as OKAY - some manufacturers
use OKAY label and others use SELECT label on their
remotes.
CC will activate the Closed Caption feature if your
device has that feature.
PIP (Picture-in-Picture) and TOGGLE buttons operate
your television’s Picture-in-Picture features. Use PIP to
activate the feature and TOGGLE to swap between the
displayed pictures on your TV.
TV/VCR and TV/DVD Combo units
Note that for some TV/VCR and TV/DVD combo units
you might need to set up two different buttons to
control both parts of the combo unit. E.G., (referring to
the Direct Code Entry section on the following page)
you might need to set up a code under the TV button to
control the TV part of the combo unit AND a separate
code for the DVD or VCR under any other button you
choose.
98
Code Entry
Direct Code Entry
1. Press and hold the Code Search button until the red
indicator stays on. Release the Code Search button.
2. Press and release the desired mode button (TV,
DVD, etc.).
The red indicator blinks, then stays lit.
3. Enter the 3 digit code from the code tables. Note:
after a valid code entry, the red indicator turns off.
For an invalid code, the red indicator flashes.
4. With your device on, press CHANNEL Up. If the
device responds, no further programming is
required. Note: If some buttons do not operate your
equipment, try one of the other codes for your
brand.
VCR
VCR
2.
TV
TV
TVTV
1.
CODE
CODE
CODECODE
SEARCH
SEARCH
SEARCHSEARCH
SLEEP
SLEEP
SLEEPSLEEP
VCRVCR
DVD
DVD
DVDDVD
CHAN
CHAN
CHANCHAN
MUTE
MUTE
MUTEMUTE
CCCCHHHHAAAANNNN
POWER
POWER
POWERPOWER
SAT
SAT
SATSAT
++++
VV
VO
V
OO
OL
LL
L
++
+
+
CCCCCCCC
CHAN
CHAN
CHANCHAN
REPEAT
REPEATREPEAT
SUBTITL E
SUBTITL E
SUBTITL ESUBTITL E
PREV
PREV
PREVPREV
REPEAT
Programming with Code Search
1. Manually turn on the device (TV, DVD, etc.) to be
controlled.
2. Press and hold Code Search button until the red
indicator stays on. Release the Code Search button.
3. Press and release the desired mode button (TV,
DVD, etc.).
The red indicator blinks, then stays lit.
4. Press the Channel Up button repeatedly (up to 300
times) until the device to be controlled changes
channel. The red indicator blinks, then stays lit. If
you accidentally overshoot the code required, press
the Channel Down button to backtrack through the
library until the device changes channel. Pressing
Channel Up changes direction to forward again.
Press and release the Mute button to install the
code.
The above assumes that you want to store SAT codes
under the SAT button, DVD codes under DVD, etc. If
you want to store a SAT code under DVD, etc., first
follow the procedure on page 10 and try ANY DVD code
from the code tables, e.g. press DVD in step 2, page 10,
and then enter ANY SAT code. Then follow the steps
above.
PIP
PIP
PIPPIP
TOGGLE/TITLE
TOGGLE/TITLE
TOGGLE/TITLETOGGLE/TITLE
3.
INPUT
INPUT
INPUTINPUT
TV/VCR
TV/VCR
ENT ER
ENT ER
ENT EREN TER
TV/VCRTV/VCR
Write your codes down here for easy reference later.
Type Type storedCode
TV TV
DVD/VCR
SAT
Note: If the device does not have a Channel Up button,
use Play (DVD only) or Power instead. Code Search
starts from the currently stored three digit number
under that mode e.g. if the mode has 100 codes and the
currently stored code is 050 then the Code Search starts
from 051 continuing to 100 before looping back to 000
and finishing at 050. This simplifies the process if you
find that several preprogrammed codes operate your
device by allowing you to bypass codes already tried.
VCR
VCR
PIP
PIP
PIPPIP
TOGGLE/TITLE
TOGGLE/TITLE
TOGGLE/TITLETOGGLE/TITLE
VCRVCR
DVD
DVD
DVDDVD
CHAN
CHAN
CHANCHAN
MUTE
MUTE
MUTEMUTE
CCCCHHHHAAAANNNN
POWER
POWER
POWERPOWER
SAT
SAT
SATSAT
++++
PREV
PREV
PREVPREV
CHAN
CHAN
CHANCHAN
VV
VO
V
OO
OL
LL
L
++
+
+
REPEAT
REPEAT
REPEATREPEAT
SUBTIT LE
SUBTIT LE
SUBTIT LESUBTIT LE
CCCCCCCC
3.
TV
TV
TVTV
2.
CODE
CODE
CODECODE
SEARCH
SEARCH
SEARCHSEARCH
SLEEP
SLEEP
SLEEPSLEEP
4.
1110
Code Identification
Sleep Timer
Code Identification
1. Press and hold Code Search button until the red
indicator stays on. Release the Code Search button.
2. Press and release the desired mode button (TV,
DVD, etc.).
The red indicator blinks, then stays lit.
3. Press and release the Code Search button. The
indicator light blinks off.
4. To find the first digit for the code stored under the
mode key pressed in step 2, press each numeric key
from 0-9 in turn. When the indicator light blinks off
the number you pressed is the first digit for the code
you are searching for.
5. To find the second digit, repeat step 4, this time
when the indicator light blinks off this is the second
digit.
6. Repeat step 4 again to find the third digit.
2.
TV
TV
TVTV
VCR
VCR
VCRVCR
DVD
DVD
DVDDVD
SAT
SAT
SATSAT
The Sleep feature enables the remote to turn off the TV
after a period of 1 to 99 minutes. Remote is to be in TV
mode to set a Sleep Timer. This feature works even if
your TV does not have this feature.
1. Press and release the TV Mode key.
2. Press and hold the Sleep button until LED remains
on (occurring after approx. 2-3 seconds).
3. Release Sleep button.
4. Press and release the numeric keys (01-99) for the
time required. The LED will blink off to indicate
keypress acceptance and remain off after second
keypress.
5. TV Sleep Timer now set.
6. Leave the Remote pointing towards the TV with an
unobstructed path.
To cancel the Sleep Timer, press and hold the Sleep key
until the LED blinks or press and release the Power key
After the batteries are installed and you have
programmed the remote for the codes that operate your
products, you can use your remote to operate a TV,
DVD/VCR, or Satellite System, etc.
TV (Press TV First)
Remote does not operate your product.
•Press the mode button of the product you want to
control.
•Program the remote with a new code.
•Install new batteries. (You might have to reprogram
your remote after installing new batteries.)
•Remote may not be compatible with your product.
Remote does not operate some features of your product.
•Program remote with a new code.
•Remote may not be able to operate all features of
your product or button names might be different
than your product.
Indicator light blinks after you program a product
code.
•Remote did not accept the code.
•Try to program the code again or try a different
code.
Satellite System
(Press SAT first)
DVD or VCR Player
(Press DVD/VCR first)
CD Player(Press CD first)
To Operate:
1. Press the TV, DVD/VCR, or SAT
button (depending on which
product you want to operate).
2. Aim the remote at the product.
3. Press POWER to turn on the
product.
4. Press other buttons to operate
the features of your product.
1918
90 Day Warranty
This product is manufactured to PHILIPS MAGNAVOX
specifications and is free from defects in material,
workmanship and assembly. This warranty extends only
to the original purchaser and is nontransferable. Should
a defect occur under normal operating conditions within
90 days from the date of purchase, PHILIPS
MAGNAVOX will provide a comparable replacement free
of charge within the warranty period, to the original
purchaser. Defective product must be returned, with the
dated proof of purchase, to the place of purchase for
replacement. This warranty does not extend to the
product if it has been damaged or rendered defective as
a result of accident, misuse, abuse, tampering with or
modification. THIS WARRANTY IS IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. IN NO EVENT SHALL PHILIPS
MAGNAVOX BE LIABLE FOR SPECIAL, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES,
WHETHER IN CONTRACT, TORT OR NEGLIGENCE.
Some States do not allow limitations on how long an
implied warranty lasts, so the above limitation may not
apply to you. Some States do not allow exclusion or
limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. This
warranty gives you specific rights and you may also
have other rights, which vary from State to State.
Made in China-TC, Quality Assured in USA
Clifton, NJ 07014-1115
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.