Philips PET737 User Guide
DVD Portable Player PET737
www.ma163.com 电子技术资料网
All version
Service Manual
©Copyright 2005 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may by reproduced, stored in a
retrieval system or transmitted, in any form or by any means, electronics,
mechanical, photocopying, or otherwise without the prior permission of Philips
TABLE OF CONTENTS
Chapter
Technical Specification & Service Tips…………..……….. 1
Safety Instructions…………………………………………….. 2
Instruction for Use……………………………………………… 3
Mechanical Instructions………………………………………. 4
Troubleshooting …………………………………………………5
Overall Block Diagram…………………………………………. 6
Electrical Diagram……………………………………………… 7
Service Part List………………………………...………………. 8
Revision List……………………………………………………. 9
3141 785 32541
Version 1.1
www.ma163.com 电子技术资料网
1.0 TECHNICAL SPECIFICATION
Service Policy on PCBA of PET737
Type /12 /93 /98
Main PCBA MLR MLR MLR
TFT PCBA MLR MLR MLR
BATTERY PCBA MLR MLR MLR
KEY PCBA MLR MLR MLR
MLR = module swap
1.0 TECHNICAL SPECIFICATION
www.ma163.com 电子技术资料网
General
Dimensions (W x H x D): 158 x 210 x 39.5 mm
Bear Unit Weight: 0.48 kg +/- 5%
Power supply:
Supply voltage (AC
adaptor 90~264)
Supply Power
consumption (AC adaptor
100/240VAC)
DC Power supply DC 6.3-15.49V
Standby Power (AC
adaptor, no load) 264VAC
Audio System
Output voltage 1kHz: 2+/-0.2V
THD 20-20kHz (%): </=2%
Dynamic range 1kHz >/=80dB
Signal/Noise ratio: >/=80dB
Frequency response (2020kHz):
Channel Separation 1kHz >=80dB
Channel Balance 1kHz <1.0dB
Current consumption
Playback time
Battery Capacity –
Lithium-ion 7.4V
Discharge cut-off
voltage(3.0 V for single cell)
Battery discharge cut-off
current
Battery Charge
voltage(1.2V for single cell)
Charging time 4 +/- 1hr
Headphone out (headphone output load 2x16 ohm)
Maximum output power:
Frequency response:
SNR (A-wght):
THD (0.2-20kHz):
Dynamic range 1kHz
Left-Right Channel
Separation:
Left-Right Channel
Balance:
Supported disc type
Video Playback
Formats:
Audio Playback
Formats:
AC 100~240V + / - 10%
9W + 10%
<0.45W
+/-3dB
1900mAH
≥
</=6.3V
</=40mA
</=8.7V
2.0mW (typical)
+/-3dB
>/=70dB (20Hz, 20kHz)
1.5%
>/=65dB
>/=55dB
</=2dB
Playback disc type: DVD, Picture-CD,
SVCD, Video CD, MP3CD, CD-R/CD-RW,
WMA-CD, DVD-R, DVDRW, DVD+R, DVD+RW
Video Playback Format: DVD / VCD / SVCD / CD
/ JPEG
Audio Playback Format: CD/MP3, MP3-DVD,
DVD
Disc Diameter 8cm / 12cm
Pixel specification
Max. 0 bright-dot & max. 3 dark-dots
Factory Service Mode (FSM)
1.0 TECHNICAL SPECIFICATION
www.ma163.com 电子技术资料网
To check the software version and change
region code of your DVD Portable
1. Power ON the DVD player and open the DVD
door
2. Press the “SETUP” button on remote control,
then select the “Preference MENU”
3. Press the remote button in the sequence as
9 -> 6 -> 5 -> 3
4. The LCD display showed the existing region
code. Press
(navigation up) or
(navigation down) repeatedly to select the
number from 0 to 6.
5. Refer below table for your region code setting
Select “0” setting = Region Free (confidential)
Procedure on how to upgrade the software of
the DVD Portable
For the best performance of your DVD Portable.
Check www.philips.com/support for latest
software upgrades available.
A) By CD-ROM
1. Download the “PHILIPS.BIN” file from the Philips
support site
2. Unzip the file and then burn it into a CD-ROM to
make a disc for upgrade
3. CD-ROM disc name must be “PHILIPS”
(otherwise it will not be recognized as a disc for
upgrade)
4. Power on the Portable DVD Player with AC/DC
adaptor
5. Play CD-ROM for firmware upgrade
Warning: Do not unplug the AC adaptor during
firmware upgrade to prevent flash corrupt of the
set!!
6. Once upgrade is completed, the player will restart
automatically and observed PHILIPS LOGO on the
screen.
7. Open the DVD door to remove the disc
2.0 SAFTETY INSTRUCTIONS
www.ma163.com 电子技术资料网
WARNING
GB
All ICs and many other semi-conductors are
susceptible to electrostatic discharges (ESD).
Careless handling during repair can reduce life
drastically.
When repairing, make sure that you are
connected with the same potential as the mass
of the set via a wrist wrap with resistance.
Keep components and tools also at this
potential.
F
ATTENTION
Tous les IC et beaucoup d’autres
semi-conducteurs sont sensibles aux
décharges statiques (ESD).
Leur longévité pourrait être considérablement
écourtée par le fait qu’aucune précaution n’est
prise à leur manipulation.
Lors de réparations, s’assurer de bien être relié
au même potentiel que la masse de l’appareil et
enfiler le bracelet serti d’une résistance de
sécurité.
Veiller à ce que les composants ainsi que les
outils que l’on utilise soient également à ce
potentiel.
ESD
D
WARNUNG
Alle ICs und viele andere Halbleiter sind
empfindlich gegenüber elektrostatischen
Entladungen (ESD).
Unsorgfältige Behandlung im Reparaturfall kan
die Lebensdauer drastisch reduzieren.
Veranlassen Sie, dass Sie im Reparaturfall über
ein Pulsarmband mit Widerstand verbunden
sind mit dem gleichen Potential wie die Masse
des Gerätes.
Bauteile und Hilfsmittel auch auf dieses gleiche
Potential halten.
WAARSCHUWING
NL
Alle IC’s en vele andere halfgeleiders zijn
gevoelig voor electrostatische ontladingen
(ESD).
Onzorgvuldig behandelen tijdens reparatie kan
de levensduur drastisch doen verminderen.
Zorg ervoor dat u tijdens reparatie via een
polsband met weerstand verbonden bent met
hetzelfde potentiaal als de massa van het
apparaat.
Houd componenten en hulpmiddelen ook op
ditzelfde potentiaal.
I
AVVERTIMENTO
Tutti IC e parecchi semi-conduttori sono
sensibili alle scariche statiche (ESD).
La loro longevità potrebbe essere fortemente
ridatta in caso di non osservazione della più
grande cauzione alla loro manipolazione.
Durante le riparazioni occorre quindi essere
collegato allo stesso potenziale che quello della
massa dell’apparecchio tramite un braccialetto
a resistenza.
Assicurarsi che i componenti e anche gli utensili
con quali si lavora siano anche a questo
potenziale.
GB
Safety regulations require that the set be restored to its original
condition and that parts which are identical with those specified,
be used.
NL
Veiligheidsbepalingen vereisen, dat het apparaat bij reparatie in
zijn oorspronkelijke toestand wordt teruggebracht en dat onderdelen,
identiek aan de gespecificeerde, worden toegepast.
F
Les normes de sécurité exigent que l’appareil soit remis à l’état
d’origine et que soient utiliséés les piéces de rechange identiques
à celles spécifiées.
D
Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu
beachten. Der Original zustand des Geräts darf nicht verändert werden;
für Reparaturen sind Original-Ersatzteile zu verwenden.
I
Le norme di sicurezza esigono che l’apparecchio venga rimesso
nelle condizioni originali e che siano utilizzati i pezzi di ricambio
identici a quelli specificati.
“Pour votre sécurité, ces documents
doivent être utilisés par des spécialistes agréés, seuls habilités à réparer
votre appareil en panne”.
CLASS 1
LASER PRODUCT
GB
Warning !
Invisible laser radiation when open.
Avoid direct exposure to beam.
S
Varning !
Osynlig laserstrålning när apparaten är öppnad och spärren
är urkopplad. Betrakta ej strålen.
Varoitus !
SF
Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina
näkymättömälle laserisäteilylle. Älä katso säteeseen!
3122 110 03420
"After servicing and before returning set to customer perform a
leakage current measurement test from all exposed metal parts to
earth ground to assure no shock hazard exist. The leakage current
Usynlig laserstråling ved åbning når sikkerhedsafbrydere er
ude af funktion. Undgå udsaettelse for stråling.
must not exceed 0.5mA."
DK Advarse !
2.1 ESD PROTECTION
www.ma163.com 电子技术资料网
Whenthepowersupplyisbeingturnedon,youmaynotremovethislasercautionslabel.Ifitremoves,radiationoflaser
maybereceived.
PREPARATIONOFSERVICING
PickupHeadconsistsofalaserdiodethatisverysusceptibletoexternalstaticelectrocity.
Althoughitoperatesproperlyafterreplacement,ifitwassubjecttoelectrostaticdischargeduringreplacement,
itslifemightbeshortened.Whenreplacing,useaconductivemat,solderingironwithgroundwire,etc.to
protectthelaserdiodeformdamagebystaticelectricity.
Andalso,theLSIandICaresameasabove.
Groundconductive
wriststrapforbody.
Solderingiron
withgroundwire
orceramictype
1M
Conductivemat
Thegroundresistance
betweenthegroundline
andthegroundislessthan10
SAFTY NOTICE
www.ma163.com 电子技术资料网
LEAKAGE CURRENT CHECK
SAFTY PRECAUTIONS
Plug the AC line cord directly into a 120V AC outlet (do
not use an isolation transformer for this check). Use an
AC voltmeter, having 5000 per volt or more sensitivity.
Connect a 1500 10W resistor,paralleled by a 0.15uF
150V AC capacitor between a knomn good earth ground
(water pipe, conduit, etc.) and all exposed metal parts of
cabinet (antennas, handle bracket, metal cabinet
screwheads, metal overlays, control shafts, etc.).
READING SHOULD NOT EXCEED 0.3V
DVD VIDEO PLAYER
Measure the AC voltage across the 1500 resistor.
The test must be conducted with the AC switch on and
then repeated with the AC switch off. The AC voltage
indicated by the meter may not exceed 0.3V.A reading
exceeding 0.3V indicates that a dangerous potential
exists, the fault must be located and corrected.
Repeat the above test with the DVD VIDEO PLAYER
power plug reversed.
NEVER RETURN A DVD VIDEO PLAYER TO THE
CUSTOMER WITHOUT TAKING NECESSARY
CORRECTIVE ACTION.
AC VOLTMETER
(5000 per volt
or more sensitivity)
Good earth ground
1500
10W
such as a water pipe,
conduit, etc.
AC OUTLET
0.15uF 150V AC
Test all exposed metal.
Voltmeter Hook-up for Leakage Current Check
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
2.2 SAFETY INSTRUCTIONS
www.ma163.com 电子技术资料网
Battery Handling Guideline
Since the battery is packed in soft package, to ensure its better performance, it’s very important to carefully handle
the battery
2.2.1 Soft Aluminium foil
The soft aluminum packing foil is very easily damaged by sharp edge parts such as Ni-tabs, pins and needles.
• Don’t strike battery with any sharp edge parts
• Trim your nail or wear glove before taking battery
• Clean worktable to make sure no any sharp particl e
2.2.2 Sealed edge
Sealing edge is very flimsy
• Don’t bend or fold sealing edge
2.2.3 Folding edge
The folding edge is form in battery process and passed all hermetic test.
• Don’t open or deform folding edge
2.2.4 Tabs
The battery tabs are not so stubborn especially for aluminum tab.
• Don’t bend tab
2.2.5 Mechanical shock
• Don’t Fall, hit, bend battery body
2.2.6 Short
Short terminals of battery is strictly prohibited, it may damage battery.
3.0 INSTRUCTION FOR USE
www.ma163.com 电子技术资料网
4.0 MECHANICAL INSTRUCTION
www.ma163.com 电子技术资料网
Disassembly Procedure
1. Remove 9pcs of screws on the side of
bottom cabinet.
Include the 1pcs of screw in CD cabinet;
2. Open the bottom cabinet carefully;
First, unplug the wire connector of key board from
the main board. (left bottom side);
3. unplug all the wire connecter from main
board,
The wire connector is for: DVD loader, battery
board and TFT driver board, and speaker.
Unplug the FFC from DVD louder, and unplug
the housing which connect DVD louder and
main board then you can take out the DVD
louder.
4.0 MECHANICAL INSTRUCTION
www.ma163.com 电子技术资料网
Remove 4pcs screws from the main board
and unplug all the housing, then you can take
the main board out from bottom cabinet.
4. Remove the flex cable on the bottom side
behind the black
5. Remove all the screws on the buttery
board( 3pcs);
and unplug the housing which connect the
battery board and main board;
Then take out the buttery with buttery board.
flannel.
.
6. Remove 6pcs screws from key board.
You can get the key board from the DVD top
cabinet
4.0 MECHANICAL INSTRUCTION
www.ma163.com 电子技术资料网
7. Remove 6pcs of screws on the display
frame behind black TFT corner-rubber.
Carefully open the display frame with the
catches by screwdriver. Then you can see
next picture.
8. To remove the TFT, de-soldering the wire
connected between PANEL and TFT board first.
(Please note the wire location as shown in picture
during re-assembly)
And unplug wire connecter from TFT board and
main board.
Take out the TFT board from cabinet using
eradicator.
Don’t forget unplug the FFC of panel from the
TFT board; it is behind the black
flannel.
After this you can take the panel from the
monitor back cabinet, you’d better be-careful,
There are three two side tape rubbers as
shown in the pictures
9. To remove the hinge, remove 4pcs screws
on the hinge.
4.0 MECHANICAL INSTRUCTION
www.ma163.com 电子技术资料网
5.0 TROUBLESHOOTING
www.ma163.com 电子技术资料网
SYMPTOM: BATTERY NO POWER
BATTERY CAN＇T
Power ON
Start
Check Battery capacity?
Yes
Check the Power-ON
button and cable OK?
NO
Replace Button or
Cable
Yes
no
Check charging
function OK?
No
Replace Main Board
Yes
No
Check adaptor
power-ON OK?
yes
SET OK?
No Defect, return
set to Customer
Loading...