ll rights reserved. No part of this publication may by reproduced, stored in a
retrieval system or transmitted, in any form or by any means, electronics,
mechanical, photocopying, or otherwise without the prior permission of Philips
TABLE OF CONTENTS
Chapter
Technical Specification…………………………………………1
Safety Instructions.……………………………………………...2
Instruction for Use.……………………………………………...3
Mechanical Instructions……………………………………….. 4
Troubleshooting & Service tips……………………………….5
Overall block diagram………………………….………...…... 6
Overall wiring diagram………………………………………… 7
Electrical diagram………………………………………………. 8
Component layout……………………………………………… 9
Service part list………………………………………………….10
Revision list………………………………………………………11
3141 785 30444
Version 1.4
1.0 TECHNICAL SPECIFICATION
General
Dimensions (WxLxH) : 19.3 x 16.1 x 3.0 cm
Weight : 0.824 kg / 1.81 lb
Power supply : DC 9V 2.2A
Power consumption :
Operating temp. range : 0 - 50°C (32 ~ 122°F)
Laser wavelength: 650nm
Video system : /17 versions: NTSC
Frequency response : 20Hz ~ 20KHz ± 1dB
Signal/noise ratio
Audio distortion + noise
Channel separation:
Dynamic range
Output
Audio out (analog audio) Output level: 2V ± 10%
Load impedance:
Video out Output level:
Load impedance:
Current consumption
DC-IN SUPPLY (9.0V)
Battery Charging Current 1.2A typ.
BATT. SUPPLY (7.2V)
Power Off 0A
Playback with TFT on <1.2A typ.
Playback without TFT on <600mA
Battery playtime >2.5hrs
Headphone out (headphone output load 2x16 ohm)
Maximum output power :
Frequency response :20Hz - 20kHz
SNR (A-wght) :80dB typ.
THD (1kHz) :<1%
Left-Right Channel
Separation :
Left-Right Channel
Balance :
Supported disc type
DVD video discs:
7.72 x 6.44 x 1.2 inches
≤ 20W
non /17 versions: NTSC / PAL /
AUTO
≥85dB
≤ 80(1KHz)
≥85dB
≥80dB
10KΩ
1Vp - p ± 20%
75Ω
>10mW
32dB typ.
1dB
Video CD:
Audio CD :
In addition, this unit can play DVD+R & DVD+RW and CD-R &
CD-RW that contains audio titles or MP3 or JPEG files.
You cannot play disc other than the above listed.
(CVD, CD-ROM, CD-Extra, CD-G and CD-I discs cannot be
played on this DVD player)
Software upgrades
For the best performance of your DVD Portable. Check
www.philips.com/support for latest software
upgrades available.
To check the software version of your DVD Portable.
1. Press the SETUP key to enter the setup menu.
2. Press RETURN and then press 1, 2 and 3 on the
remote control.
3. The display will show the software version as the
date of which the software was built on the bottom
of the screen. E.g. 050303
Procedure on how to upgrade the software of the DVD
Portable
1. Download the latest software from the Philips
support site.
2. Unzipped the files and then burn it onto a CD ROM
then playback the CD ROM on the DVD Portable.
Pixel specification
<= 3 (max. 0 bright dots and 3 dark dots)
WARNING
GB
All ICs and many other semi-conductors are
susceptible to electrostatic discharges (ESD).
Careless handling during repair can reduce life
drastically.
When repairing, make sure that you are
connected with the same potential as the mass
of the set via a wrist wrap with resistance.
Keep components and tools also at this
potential.
F
ATTENTION
Tous les IC et beaucoup d’autres
semi-conducteurs sont sensibles aux
décharges statiques (ESD).
Leur longévité pourrait être considérablement
écourtée par le fait qu’aucune précaution n’est
prise à leur manipulation.
Lors de réparations, s’assurer de bien être relié
au même potentiel que la masse de l’appareil et
enfiler le bracelet serti d’une résistance de
sécurité.
Veiller à ce que les composants ainsi que les
outils que l’on utilise soient également à ce
potentiel.
2.0 SAFETY INSTRUCTIONS
ESD
D
WARNUNG
Alle ICs und viele andere Halbleiter sind
empfindlich gegenüber elektrostatischen
Entladungen (ESD).
Unsorgfältige Behandlung im Reparaturfall kan
die Lebensdauer drastisch reduzieren.
Veranlassen Sie, dass Sie im Reparaturfall über
ein Pulsarmband mit Widerstand verbunden
sind mit dem gleichen Potential wie die Masse
des Gerätes.
Bauteile und Hilfsmittel auch auf dieses gleiche
Potential halten.
WAARSCHUWING
NL
Alle IC’s en vele andere halfgeleiders zijn
gevoelig voor electrostatische ontladingen
(ESD).
Onzorgvuldig behandelen tijdens reparatie kan
de levensduur drastisch doen verminderen.
Zorg ervoor dat u tijdens reparatie via een
polsband met weerstand verbonden bent met
hetzelfde potentiaal als de massa van het
apparaat.
Houd componenten en hulpmiddelen ook op
ditzelfde potentiaal.
I
AVVERTIMENTO
Tutti IC e parecchi semi-conduttori sono
sensibili alle scariche statiche (ESD).
La loro longevità potrebbe essere fortemente
ridatta in caso di non osservazione della più
grande cauzione alla loro manipolazione.
Durante le riparazioni occorre quindi essere
collegato allo stesso potenziale che quello della
massa dell’apparecchio tramite un braccialetto
a resistenza.
Assicurarsi che i componenti e anche gli utensili
con quali si lavora siano anche a questo
potenziale.
GB
Safety regulations require that the set be restored to its original
condition and that parts which are identical with those specified,
be used.
NL
Veiligheidsbepalingen vereisen, dat het apparaat bij reparatie in
zijn oorspronkelijke toestand wordt teruggebracht en dat onderdelen,
identiek aan de gespecificeerde, worden toegepast.
F
Les normes de sécurité exigent que l’appareil soit remis à l’état
d’origine et que soient utiliséés les piéces de rechange identiques
à celles spécifiées.
D
Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu
beachten. Der Original zustand des Geräts darf nicht verändert werden;
für Reparaturen sind Original-Ersatzteile zu verwenden.
“Pour votre sécurité, ces documents
doivent être utilisés par des spécialistes agréés, seuls habilités à réparer
votre appareil en panne”.
CLASS 1
LASER PRODUCT
GB
Invisible laser radiation when open.
Avoid direct exposure to beam.
Osynlig laserstrålning när apparaten är öppnad och spärren
är urkopplad. Betrakta ej strålen.
Warning !
S
Varning !
3122 110 03420
I
Le norme di sicurezza esigono che l’apparecchio venga rimesso
nelle condizioni originali e che siano utilizzati i pezzi di ricambio
identici a quelli specificati.
"After servicing and before returning set to customer perform a
leakage current measurement test from all exposed metal parts to
earth ground to assure no shock hazard exist. The leakage current
must not exceed 0.5mA."
Varoitus !
SF
Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina
näkymättömälle laserisäteilylle. Älä katso säteeseen!
DKAdvarse !
Usynlig laserstråling ved åbning når sikkerhedsafbrydere er
ude af funktion. Undgå udsaettelse for stråling.