Philips P83C749EBPN, P83C749EBDDB, P83C749EBAA Datasheet

INTEGRATED CIRCUITS

83C749/87C749

80C51 8-bit microcontroller family

2K/64 OTP/ROM, 5 channel 8-bit A/D, PWM, low pin count

Preliminary specification Supersedes data of 1998 Jan 06 IC20 Data Handbook

 

1998 Apr 23

Philips Semiconductors Preliminary specification

80C51 8-bit microcontroller family

2K/64 OTP/ROM, 5 channel 8-bit A/D, PWM, low pin count

DESCRIPTION

The Philips 83C749/87C749 offers many of the advantages of the 80C51 architecture in a small package and at low cost.

The 8XC749 Microcontroller is fabricated with Philips high-density CMOS technology. Philips epitaxial substrate minimizes CMOS latch-up sensitivity.

The 8XC749 contains a 2k × 8 ROM (83C749) EPROM (87C749), a 64 × 8 RAM, 21 I/O lines, a 16-bit auto-reload counter/timer, a fixed-priority level interrupt structure, an on-chip oscillator, a five channel multiplexed 8-bit A/D converter, and an 8-bit PWM output.

The EPROM version of this device, the 87C749, is available in plastic one-time programmable (OTP) packages. Once the array has been programmed, it is functionally equivalent to the masked ROM 83C749. Thus, unless explicitly stated otherwise, all references made to the 83C749 apply equally to the 87C749.

The 83C749 supports two power reduction modes of operation referred to as the idle mode and the power-down mode.

FEA TURES

•Available in erasable quartz lid or One-Time Programmable plastic

packages

•80C51 based architecture

•Small package sizes

– 28-pin DIP – 28-pin Shrink Small Outline Package (SSOP) – 28-pin PLCC

•Wide oscillator frequency range: 3.5MHz to 16MHz

•Low power consumption:

– Normal operation: less than 11mA @ 5V, 12MHz – Idle mode – Power-down mode

•2k × 8 ROM (83C749)

EPROM (87C749)

•64 × 8 RAM

•16-bit auto reloadable counter/timer

•5-channel 8-bit A/D converter

•8-bit PWM output/timer

•10-bit fixed-rate timer

•Boolean processor

•CMOS and TTL compatible

•Well suited for logic replacement, consumer and industrial

applications

83C749/87C749

P ART NUMBER SELECTION

ROM EPROM

P83C749EBP N P87C749EBP N OTP 0 to +70, 28-pin Plastic Dual In-line Package 3.5 to 16MHz SOT117-2 P83C749EBA A P87C749EBA A OTP 0 to +70, 28-pin Plastic Leaded Chip Carrier 3.5 to 16MHz SOT261-3

P83C749EBD DB P87C749EBD DB OTP 0 to +70, 28-pin Shrink Small Outline Package 3.5 to 16MHz SOT341-1

NOTE:

1. OTP = One Time Programmable EPROM.

TEMPERATURE RANGE °C

AND PACKAGE

FREQUENCY

DRAWING

NUMBER

1998 Apr 23

Philips Semiconductors Preliminary specification

80C51 8-bit microcontroller family

2K/64 OTP/ROM, 5 channel 8-bit A/D, PWM, low pin count

BLOCK DIAGRAM

P0.0–P0.4

PORT 0

DRIVERS

RAM ADDR

RAM

ACC

TMP2

PSW

PORT 0

LATCH

ALU

PWM

PORT 2

LATCH

TMP1

PCON TCON

TH0 TL0 RTH RTL

INTERRUPT AND

TIMER BLOCKS

STACK

POINTER

ROM/

EPROM

83C749/87C749

PROGRAM

ADDRESS

BUFFER

INCRE-

MENTER

RST

TIMING

AND

CONTROL

OSCILLATOR

INSTRUCTION

ADC

SSAVCC

PORT 1

LATCH

PORT 1

DRIVERS

P1.0–P1.7

PORT 3

LATCH

PORT 3

DRIVERS

P3.0–P3.7

PROGRAM COUNTER

DPTR

SU00305

1998 Apr 23

Philips Semiconductors Preliminary specification

80C51 8-bit microcontroller family

2K/64 OTP/ROM, 5 channel 8-bit A/D, PWM, low pin count

PIN CONFIGURATION

P3.4/A4

P3.3/A3

P3.2/A2/A10

P3.1/A1/A9 P3.0/A0/A8

P0.2/V

P0.1/OE–PGM

P0.0/ASEL

RST

P1.0/ADC0/D0 P1.1/ADC1/D1

1 2

4 5

PLASTIC

DUAL

X2 X1

7 8

9 10 11 12 13 14

IN-LINE

PACKAGE

AND

SHRINK

SMALL

OUTLINE

PACKAGE

P3.5/A5

P3.6/A6

P3.7/A7

25 24

P0.4/PWM OUT

P0.3

P1.7/T0/D7

P1.6/INT1/D6

P1.5/INT0/D5

P1.4/ADC4/D4

P1.3/ADC3/D3

P1.2/ADC2/D2

83C749/87C749

4126

12 18

Pin Function

1 P3.4/A4 2 P3.3/A3 3 P3.2/A2/A10 4 P3.1/A1/A9 5 P3.0/A0/A8 6 P0.2/V 7 P0.1/OE-PGM 8 P0.0/ASEL

9 RST 10 X2 11 X1 12 V 13 P1.0/ADC0/D0 14 P1.1/ADC1/D1

PLASTIC LEADED

CHIP

CARRIER

Pin Function

15 P1.2/ADC2/D2 16 P1.3/ADC3/D3 17 P1.4/ADC4/D4 18 AV 19 AV 20 P1.5/INT0/D5 21 P1.6/INT1 22 P1.7/T0/D7 23 P0.3 24 P0.4/PWM OUT 25 P3.7/A7 26 P3.6/A6 27 P3.5/A5 28 V

SS CC

/D6

SU00304

1998 Apr 23

Philips Semiconductors Preliminary specification

80C51 8-bit microcontroller family

83C749/87C749

2K/64 OTP/ROM, 5 channel 8-bit A/D, PWM, low pin count

PIN DESCRIPTION

MNEMONIC PIN NO. TYPE NAME AND FUNCTION

P0.0–P0.4 8–6

P1.0–P1.7 13–17,

P3.0–P3.7 5–1,

RST 9 I Reset: A high on this pin for two machine cycles while the oscillator is running resets the device. An

X1 11 I Crystal 1: Input to the inverting oscillator amplifier and input to the internal clock generator circuits. X1

X2 10 O Crystal 2: Output from the inverting oscillator amplifier.

NOTE:

1. AV

(reference ground) must be connected to 0V (ground). AVCC (reference input) cannot differ from VCC by more than ±0.2V, and must be

in the range 4.5V to 5.5V .

2. When P0.2 is at or close to 0 volt, it may affect the internal ROM operation. We recommend that P0.2 be tied to V (e.g., 2kΩ).

12 I Circuit Ground Potential. 28 I Supply voltage during normal, idle, and power-down operation.

I/O Port 0: Port 0 is a 5-bit bidirectional port. Port 0.0–P0.2 are open drain. Port 0.0–P0.2 pins that have

23, 24

1s written to them float, and in that state can be used as high-impedance inputs. P0.3–P0.4 are bidirectional I/O port pins with internal pull-ups. These pins are driven low if the port register bit is written with a 0. The state of the pin can always be read from the port register by the program. Port 0.3 and 0.4 have internal pull-ups that function identically to port 3. Pins that have 1s written to them are pulled high by the internal pull-ups and can be used as inputs.

While P0.0 anbd P0.1 differ from “standard TTL” characteristics, they are close enough for the pins to still be used as general-purpose I/O.

6 I VPP (P0.2) – Programming voltage input. (See Note 2.) 7 I OE/PGM (P0.1) – Input which specifies verify mode (output enable) or the program mode.

OE/PGM = 1 output enabled (verify mode). OE/PGM = 0 program mode.

8 I ASEL (P0.0) – Input which indicates which bits of the EPROM address are applied to port 3.

ASEL = 0 low address byte available on port 3. ASEL = 1 high address byte available on port 3 (only the three least significant bits are used).

I/O Port 1: Port 1 is an 8-bit bidirectional I/O port with internal pull-ups. Port 1 pins that have 1s written to

20–22

them are pulled high by the internal pull-ups and can be used as inputs. P0.3–P0.4 pins are bidirectional I/O port pins with internal pull-ups. As inputs, port 1 pins that are externally pulled low will source current because of the internal pull-ups. (See DC Electrical Characteristics: I serves the special function features of the SC80C51 family as listed below:

). Port 1 also

20 I INT0 (P1.5): External interrupt. 21 I INT1 (P1.6): External interrupt. 22 I T0 (P1.7): T imer 0 external input.

13–17 I ADC0 (P1.0)–ADC4 (P1.4): Port 1 also functions as the inputs to the five channel multiplexed A/D

converter. These pins can be used as outputs only if the A/D function has been disabled. These pins can be used as digital inputs while the A/D converter is enabled.

Port 1 serves to output the addressed EPROM contents in the verify mode and accepts as inputs the value to program into the selected address during the program mode.

I/O Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins that have 1s written to

27–25

them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 3 pins that are externally being pulled low will source current because of the pull-ups. (See DC Electrical Characteristics: I programmed (or verified). The 11-bit address is multiplexed into this port as specified by P0.0/ASEL.

). Port 3 also functions as the address input for the EPROM memory location to be

internal diffused resistor to VSS permits a power-on RESET using only an external capacitor to VCC. After the device is reset, a 10-bit serial sequence, sent LSB first, applied to RESET, places the device in the programming state allowing programming address, data and V or verification purposes. The RESET serial sequence must be synchronized with the X1 input.

to be applied for programming

also serves as the clock to strobe in a serial bit stream into RESET to place the device in the programming state.

19 I Analog supply voltage and reference input. 18 I Analog supply and reference ground.

via a small pullup

1998 Apr 23

Philips Semiconductors Preliminary specification

80C51 8-bit microcontroller family

2K/64 OTP/ROM, 5 channel 8-bit A/D, PWM, low pin count

OSCILLA T OR CHARACTERISTICS

X1 and X2 are the input and output, respectively, of an inverting amplifier which can be configured for use as an on-chip oscillator.

To drive the device from an external clock source, X1 should be driven while X2 is left unconnected. There are no requirements on the duty cycle of the external clock signal, because the input to the internal clock circuitry is through a divide-by-two flip-flop. However, minimum and maximum high and low times specified in the data sheet must be observed.

IDLE MODE

The 8XC749 includes the 80C51 power-down and idle mode features. In idle mode, the CPU puts itself to sleep while all of the on-chip peripherals except the A/D and PWM stay active. The functions that continue to run while in the idle mode are Timer 0, Timer I, and the interrupts. The instruction to invoke the idle mode is the last instruction executed in the normal operating mode before the idle mode is activated. The CPU contents, the on-chip RAM, and all of the special function registers remain intact during this mode. The idle mode can be terminated either by any enabled interrupt (at which time the process is picked up at the interrupt service routine and continued), or by a hardware reset which starts the processor in the same manner as a power-on reset. Upon powering-up the circuit, or exiting from idle mode, sufficient time must be allowed for stabilization of the internal analog reference voltages before an A/D conversion is started.

Special Function Registers

The special function registers (directly addressable only) contain all of the 8XC751 registers except the program counter and the four register banks. Most of the 21 special function registers are used to control the on-chip peripheral hardware. Other registers include arithmetic registers (ACC, B, PSW), stack pointer (SP) and data pointer registers (DPH, DPL). Nine of the SFRs are bit addressable.

Data Pointer

The data pointer (DPTR) consists of a high byte (DPH) and a low byte (DPL). In the 80C51 this register allows the access of external data memory using the MOVX instruction. Since the 83C749 does not support MOVX or external memory accesses, this register is generally used as a 16-bit offset pointer of the accumulator in a MOVC instruction. DPTR may also be manipulated as two independent 8-bit registers.

POWER-DOWN MODE

In the power-down mode, the oscillator is stopped and the instruction to invoke power-down is the last instruction executed. Only the contents of the on-chip RAM are preserved. A hardware reset is the only way to terminate the power-down mode. The control bits for the reduced power modes are in the special function register PCON.

Table 1. External Pin Status During Idle and

Power-Down Modes

MODE Port 0* Port 1 Port 2

Idle Data Data Data Power-down Data Data Data

* Except for PWM output (P0.4).

DIFFERENCES BETWEEN THE 8XC749 AND THE 80C51

Program Memory

On the 8XC749, program memory is 2048 bytes long and is not externally expandable, so the 80C51 instructions MOVX, LJMP, and LCALL are not implemented. If these instructions are executed, the appropriate number of instruction cycles will take place along with external fetches; however, no operation will take place. The LJMP may not respond to all program address bits. The only fixed locations in program memory are the addresses at which execution is taken up in response to reset and interrupts, which are as follows:

Event Address

Reset 000 External INT0 Counter/timer 0 00B External INT1 013 Timer I 01B ADC 02B PWM 033

Memory Organization

The 8XC749 manipulates operands in three memory address spaces. The first is the program memory space which contains program instructions as well as constants such as look-up tables. The program memory space contains 2k bytes in the 8XC749.

The second memory space is the data memory array which has a logical address space of 128 bytes. However, only the first 64 (0 to 3FH) are implemented in the 8XC749.

The third memory space is the special function register array having a 128-byte address space (80H to FFH). Only selected locations in this memory space are used (see Table 2). Note that the architecture of these memory spaces (internal program memory, internal data memory , and special function registers) is identical to the 80C51, and the 8XC749 varies only in the amount of memory physically implemented.

The 8XC749 does not directly address any external data or program memory spaces. For this reason, the MOVX instructions in the 80C51 instruction set are not implemented in the 83C749, nor are the alternate I/O pin functions RD

I/O Ports

The I/O pins provided by the 83C749 consist of port 0, port 1, and port 3.

Port 0

Port 0 is a 5-bit bidirectional I/O port and includes alternate functions on some pins of this port. Pins P0.3 and P0.4 are provided with internal pullups while the remaining pins (P0.0, P0.1, and P0.2) have open drain output structures. The alternate function for port P0.4 is PWM output.

If the alternate function PWM is not being used, then this pin may be used as an I/O port.

83C749/87C749

Program Memory

003

and WR.

1998 Apr 23

Philips Semiconductors Preliminary specification

80C51 8-bit microcontroller family

2K/64 OTP/ROM, 5 channel 8-bit A/D, PWM, low pin count

Port 1

Port 1 is an 8-bit bidirectional I/O port whose structure is identical to the 80C51, but also includes alternate input functions on all pins. The alternate pin functions for port 1 are:

P1.0-P1.4 - ADC0-ADC4 - A/D converter analog inputs P1.5 INT0 P1.6 INT1

- external interrupt 0 input

- external interrupt 1 input

P1.7 - T0 - timer 0 external input If the alternate functions INT0

, INT1, or T0 are not being used, these

pins may be used as standard I/O ports. It is necessary to connect

and AVSS to VCC and VSS, respectively, in order to use P1.5,

P1.6, and P1.7 pins as standard I/O pins. When the A/D converter is enabled, the analog channel connected to the A/D may not be used as a digital input; however, the remaining analog inputs may be used as digital inputs. They may not be used as digital outputs. While the A/D is enabled, the analog inputs are floating.

Port 3

Port 3 is an 8-bit bidirectional I/O port whose structure is identical to the 80C51. Note that the alternate functions associated with port 3 of the 80C51 have been moved to port 1 of the 83C749 (as applicable). See Figure 1 for port bit configurations.

Counter/Timer Subsystem

The 8XC749 has one counter/timer called timer/counter 0. Its operation is similar to mode 2 operation on the 80C51, but is extended to 16 bits with 16 bits of autoload. The controls for this counter are centralized in a single register called TCON.

Timer I Implementation

Timer I is clocked once per machine cycle, which is the oscillator frequency divided by 12. The timer operation is enabled by setting the TIRUN bit (bit 4) in the I2CFG register. Writing a 0 into the TIRUN bit will stop and clear the timer. The timer is 10 bits wide, and when it reaches the terminal count of 1024, it carries out and sets the Timer I interrupt flag. An interrupt will occur if the Timer I interrupt is enabled by bit ETI (bit 4) of the Interrupt Enable (IE) register, and global interrupts are enabled by bit EA (bit 7) of the same IE register.

The vector address for the Timer I interrupt is 1Bhex, and the interrupt service routine must start at this address. As with all 8051 family microcontrollers, only the Program Counter is pushed onto the stack upon interrupt (other registers that are used both by the

interrupt service routine and elsewhere must be explicitly saved). The Timer I interrupt flag is cleared by setting the CKRTI bit (bit 5 of the I1CFG register. For more information, see application note AN427.

Interrupt Subsystem—Fixed Priority

The IP register and the 2-level interrupt system of the 80C51 are eliminated. The interrupt structure is a seven-source, one-level interrupt system similar to the 8XC751. Simultaneous interrupt conditions are resolved by a single-level, fixed priority as follows: Highest priority: Pin INT0

Lowest priority: ADC The vector addresses are as follows:

Source Vector Address

INT0 0003H TF0 000BH INT1 0013H TIMER I 001BH ADC 002BH PWM 0033H

Interrupt Control Registers

The 80C51 interrupt enable register is modified to take into account the different interrupt sources of the 8XC749.

Interrupt Enable Register

MSB LSB

Position Symbol Function

IE.7 EA Global interrupt disable when EA = 0 IE.6 EAD A/D conversion complete IE.5 ETI Timer I IE.4 — IE.3 EPWM PWM counter overflow IE.2 EX1 External interrupt 1 IE.1 ET0 Timer 0 overflow IE.0 EX0 External interrupt 0

83C749/87C749

Counter/timer flag 0 Pin INT1 PWM Timer I

EAD ETI — EPWM EX1 ET0 EX0

READ

LATCH

INT. BUS

WRITE TO

LATCH

READ

1998 Apr 23

ALTERNATE

OUTPUT

FUNCTION

P1.X

LATCH

CL Q

ALTERNATE INPUT

FUNCTION

READ

INTERNAL

PULL-UP

P1.X

LATCH

INT. BUS

WRITE TO

LATCH

READ

Figure 1. Port Bit Latches and I/O Buffers

ALTERNATE

OUTPUT

FUNCTION

P0.X

LATCH

CL Q

ALTERNATE INPUT

FUNCTION

P0.X

SU00306

+ 15 hidden pages