Philips P83C652IFAA, P83C652IBAA, P83C652IBA, P83C652FFPN, P80C652IFA Datasheet

...

 

80C652/83C652

CMOS single-chip 8-bit microcontrollers

Product specification 1996 Aug 15

INTEGRATED CIRCUITS

IC20 Data Handbook

PORT 0PORT 1PORT 2

PORT 3

ADDRESS AND

DATA BUS

ADDRESS BUS

VSSV

ALTERNATE

FUNCTIONS

RST

XTAL1 XTAL2

ALE

PSEN

RxD

TxD INT0 INT1

T0 T1

SCL SDA

Phlips Semiconductors Product specification

80C652/83C652CMOS single-chip 8-bit microcontrollers

1996 Aug 15

DESCRIPTION

The P80C652/83C652 Single-Chip 8-Bit Microcontroller is manufactured in an advanced CMOS process and is a derivative of the 80C51 microcontroller family. The 80C652/83C652 has the same instruction set as the 80C51. Three versions of the derivative exist:

83C652 — 8k bytes mask programmable

ROM 80C652 — ROMless version 87C652 — EPROM version (described in a

separate chapter) This device provides architectural

enhancements that make it applicable in a variety of applications for general control systems. The 8XC652 contains a non-volatile 8k × 8 read-only program memory, a volatile 256 × 8 read/write data memory, four 8-bit I/O ports, two 16-bit timer/event counters (identical to the timers of the 80C51), a multi-source, two-priority-level, nested interrupt structure, an I

C interface, UART and on-chip oscillator and timing circuits. For systems that require extra capability, the 8XC652 can be expanded using standard TTL compatible memories and logic.

The device also functions as an arithmetic processor having facilities for both binary and BCD arithmetic plus bit-handling capabilities. The instruction set consists of over 100 instructions: 49 one-byte, 45 two-byte and 17 three-byte. With a 16(24)MHz crystal, 58% of the instructions are executed in 0.75(0.5)µs and 40% in 1.5(1)µs. Multiply and divide instructions require 3(2)µs.

LOGIC SYMBOL

FEATURES

•80C51 central processing unit

•8k × 8 ROM expandable externally to

64k bytes

•256 × 8 RAM, expandable externally to

64k bytes

•Two standard 16-bit timer/counters

•Four 8-bit I/O ports

•I

C-bus serial I/O port with byte oriented

master and slave functions

•Full-duplex UART facilities

•Power control modes

– Idle mode – Power-down mode

•ROM code protection

•Extended frequency range: 1.2 to 24 MHz

•Three operating ambient temperature

ranges:

0 to +70°C –40 to +85°C –40 to +125°C

PIN CONFIGURATIONS

1 2 3

4 5

9 10 11 12 13

14 15 16 17 18 19 20

P1.0 P1.1

P1.2

P1.3 P1.4

P1.5

SCL/P1.6

RST RxD/P3.0 TxD/P3.1

INT0

/P3.2

INT1

/P3.3 T0/P3.4 T1/P3.5

SDA/P1.7

/P3.7

XTAL2 XTAL1

P2.0/A8

P2.1/A9

P2.2/A10

P2.3/A11

P2.4/A12

P2.5/A13

P2.6/A14

P2.7/A15

PSEN

ALE

P0.7/AD7

P0.6/AD6

P0.5/AD5

P0.4/AD4

P0.3/AD3

P0.2/AD2

P0.1/AD1

P0.0/AD0

6 1 40

18 28

12 22

/P3.6

PLASTIC

DUAL

IN-LINE

PACKAGE

PLASTIC

LEADED

CHIP

CARRIER

PLASTIC

QUAD

FLAT

PACK

Phlips Semiconductors Product specification

80C652/83C652CMOS single-chip 8-bit microcontrollers

1996 Aug 15

CERAMIC AND PLASTIC LEADED CHIP CARRIER PIN FUNCTIONS

6 1 40

18 28

CERAMIC

AND

PLASTIC

LEADED CHIP

CARRIER

Pin Function Pin Function

1 NC* 23 NC* 2 P1.0 24 P2.0/A8 3 P1.1 25 P2.1/A9 4 P1.2 26 P2.2/A10 5 P1.3 27 P2.3/A11 6 P1.4 28 P2.4/A12 7 P1.5 29 P2.5/A13 8 P1.6/SCL 30 P2.6/A14 9 P1.7/SDA 31 P2.7/A15

10 RST 32 PSEN

11 P3.0/RxD 33 ALE 12 NC* 34 NC* 13 P3.1/TxD 35 EA 14 P3.2/INT0 36 P0.7/AD7 15 P3.3/INT1 37 P0.6/AD6 16 P3.4/T0 38 P0.5/AD5 17 P3.5/T1 39 P0.4/AD4 18 P3.6/WR 40 P0.3/AD3 19 P3.7/RD 41 P0.2/AD2 20 XTAL2 42 P0.1/AD1 21 XTAL1 43 P0.0/AD0 22 V

44 V

*DO NOT CONNECT

PLASTIC QUAD FLAT PACK PIN FUNCTIONS

44 34

12 22

PLASTIC

QUAD

FLAT

PACK

Pin Function Pin Function

1 P1.5 23 P2.5/A13 2 P1.6/SCL 24 P2.6/A14 3 P1.7/SDA 25 P2.7/A15 4 RST 26 PSEN 5 P3.0/RxD 27 ALE 6 V

SS4

28 V

SS2

7 P3.1/TxD 29

8 P3.2/INT0 30 P0.7/AD7

9 P3.3/INT1 31 P0.6/AD6 10 P3.4/T0 32 P0.5/AD5 11 P3.5/T1 33 P0.4/AD4 12 P3.6/WR 34 P0.3/AD3 13 P3.7/RD 35 P0.2/AD2 14 XTAL2 36 P0.1/AD1 15 XTAL1 37 P0.0/AD0 16 V

SS1

38 V

17 NC* 39 V

SS3

18 P2.0/A8 40 P1.0 19 P2.1/A9 41 P1.1 20 P2.2/A10 42 P1.2 21 P2.3/A11 43 P1.3 22 P2.4/A12 44 P1.4

*DO NOT CONNECT

NOTES TO QFP ONLY:

1. Due to EMC improvements, all V

pins

(6, 16, 28, 39) must be connected to V

on the 80C652/83C652.

Phlips Semiconductors Product specification

80C652/83C652CMOS single-chip 8-bit microcontrollers

1996 Aug 15

ORDER INFORMATION

PHILIPS

PART ORDER NUMBER

PART MARKING

PHILIPS NORTH AMERICA

PART ORDER NUMBER

TEMPERATURE

RANGE (°C)

FREQ

ROMless ROM

Drawing

Number

ROMless ROM AND PACKAGE MHz

1,2

P80C652FBP P83C652FBP/xxx SOT129-1 P80C652FBPN P83C652FBPN 0 to +70, Plastic Dual In-line Package 16

P80C652FBA P83C652FBA/xxx SOT187-2 P80C652FBAA P83C652FBAA 0 to +70, Plastic Leaded Chip Carrier 16

P80C652FBB P83C652FBB/xxx SOT307-24P80C652FBBB P83C652FBBB 0 to +70, Plastic Quad Flat Pack 16 P80C652FFP P83C652FFP/xxx SOT129-1 P80C652FFPN P83C652FFPN –40 to +85, Plastic Dual In-line Package 16

P80C652FFA P83C652FFA/xxx SOT187-2 P80C652FFAA P83C652FFAA –40 to +85, Plastic Leaded Chip Carrier 16 P80C652FFB P83C652FFB/xxx SOT307-24P80C652FFBB P83C652FFBB –40 to +85, Plastic Quad Flat Pack 16 P80C652FHP P83C652FHP/xxx SOT129-1 P80C652FHPN P83C652FHPN –40 to +125, Plastic Dual In-line Package 16 P80C652FHA P83C652FHA/xxx SOT187-2 P80C652FHAA P83C652FHAA –40 to +125, Plastic Leaded Chip Carrier 16 P80C652FHB P83C652FHB/xxx SOT307-24P80C652FHBB P83C652FHBB –40 to +125, Plastic Quad Flat Pack 16

P80C652IBP P83C652IBP/xxx SOT129-1 P80C652IBPN P83C652IBPN 0 to +70, Plastic Dual In-line Package 24 P80C652IBA P83C652IBA/xxx SOT187-2 P80C652IBAA P83C652IBAA 0 to +70, Plastic Leaded Chip Carrier 24 P80C652IBB P83C652IBB/xxx SOT307-24P80C652IBBB P83C652IBBB 0 to +70, Plastic Quad Flat Pack 24 P80C652IFP P83C652IFP/xxx SOT129-1 P80C652IFPN P83C652IFPN –40 to +85, Plastic Dual In-line Package 24 P80C652IFA P83C652IFA/xxx SOT187-2 P80C652IFAA P83C652IFAA –40 to +85, Plastic Leaded Chip Carrier 24 P80C652IFB P83C652IFB/xxx SOT307-24P80C652IFBB P83C652IFBB –40 to +85, Plastic Quad Flat Pack 24

NOTES:

1. 80C652 and 83C652 frequency range is 1.2MHz–16MHz or 1.2 to 24MHz.

2. For specification of the EPROM version, see the 87C652 data sheet.

3. xxx denotes the ROM code number.

4. SOT311 replaced by SOT307-2.

Phlips Semiconductors Product specification

80C652/83C652CMOS single-chip 8-bit microcontrollers

1996 Aug 15

TEMPERATURE

RANGE (°C)

FREQ

EPROM

Drawing Number

AND PACKAGE MHz

1,2

S87C652-4N40 SOT129-1 0 to +70, Plastic Dual In-line Package 16 S87C652-4F40 0590B

0 to +70, Ceramic Dual In-line

Package w/Window

S87C652-4A44 SOT187-2 0 to +70, Plastic Leaded Chip Carrier 16 S87C652-4K44 1472A

0 to +70, Ceramic Leaded Chip Carrier

w/Window

S87C652-4B44 SOT307-2 0 to +70, Plastic Quad Flat Pack 16 S87C652-5N40 SOT129-1 –40 to +85, Plastic Dual In-line Package 16

S87C652-5F40 0590B

–40 to +85, Ceramic Dual In-line Package

w/Window

S87C652-5A44 SOT187-2 –40 to +85, Plastic Leaded Chip Carrier 16 S87C652-5B44 SOT307-2 –40 to +85, Plastic Quad Flat Pack 16

S87C652-7N40 SOT129-1 0 to +70, Plastic Dual In-line Package 20 S87C652-7F40 0590B

0 to +70, Ceramic Dual In-line Package

w/Window

20 S87C652-7A44 SOT187-2 0 to +70, Plastic Leaded Chip Carrier 20 S87C652-7K44 1472A

0 to +70, Ceramic Leaded Chip Carrier

w/Window

S87C652-8N40 SOT129-1 –40 to +85, Plastic Dual In-line Package 20 S87C652-8F40 0590B

–40 to +85, Ceramic Dual In-line Package

w/Window

S87C652-8A44 SOT187-2 –40 to +85, Plastic Leaded Chip Carrier 20

Phlips Semiconductors Product specification

80C652/83C652CMOS single-chip 8-bit microcontrollers

1996 Aug 15

BLOCK DIAGRAM

64K BYTE BUS

EXPANSION

CONTRTOL

PROG SERIAL PORT FULL DUPLEX UART

SYNCHRONOUS SHIFT

PROGRAMMABLE I/O

CPU

OSCILLATOR

AND

TIMING

PROGRAM

MEMORY

DATA

MEMORY

(256 x 8 RAM)

TWO 16-BIT

TIMER/EVENT

COUNTERS

C SERIAL I/O

SDA

SCL

SHARED

WITH

PORT 1

T0 T1

COUNTERS

XTAL2 XTAL1

FREQUENCY REFERENCE

INTERNAL

INTERRUPTS

EXTERNAL

INTERRUPTS

CONTROL

PARALLEL PORTS,

ADDRESS/DATA BUS

AND I/O PINS

SERIAL IN SERIAL OUT

SHARED WITH

PORT 3

(8K x 8 ROM)

INT0

INT1

Phlips Semiconductors Product specification

80C652/83C652CMOS single-chip 8-bit microcontrollers

1996 Aug 15

PIN DESCRIPTIONS

PIN NUMBER

MNEMONIC

DIP PLCC QFP TYPE NAME AND FUNCTION

20 22 6, 16,

28, 39

I Ground: 0V reference. With the QFP package all VSS pins (V

SS1

to V

SS4

) must be

connected.

40 44 38 I Power Supply: This is the power supply voltage for normal, idle, and power-down

operation.

P0.0–0.7 39–32 43–36 37–30 I/O Port 0: Port 0 is an open-drain, bidirectional I/O port. Port 0 pins that have 1s written to

them float and can be used as high-impedance inputs. Port 0 is also the multiplexed low-order address and data bus during accesses to external program and data memory. In this application, it uses strong internal pull-ups when emitting 1s.

P1.0–P1.7 1–8 2–9 40–44,

1–3

I/O Port 1: Port 1 is an 8-bit bidirectional I/O port with internal pull-ups, except P1.6 and P1.7

which are open drain. Port 1 pins that have 1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 1 pins that are externally pulled low will source current because of the internal pull-ups. (See DC Electrical Characteristics: I

). Alternate functions include: P1.6 7 8 2 I/O SCL: I2C-bus serial port clock line. P1.7 8 9 3 I/O SDA: I2C-bus serial port data line.

P2.0–P2.7 21–28 24–31 18–25 I/O Port 2: Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2 pins that have 1s

written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 2 pins that are externally being pulled low will source current because of the internal pull-ups. (See DC Electrical Characteristics: I

). Port 2 emits the high-order address byte during fetches from external program memory and during accesses to external data memory that use 16-bit addresses (MOVX @DPTR). In this application, it uses strong internal pull-ups when emitting 1s. During accesses to external data memory that use 8-bit addresses (MOV @Ri), port 2 emits the contents of the P2 special function register.

P3.0–P3.7 10–17 11,

13–195,7–13

I/O Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins that have 1s

written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 3 pins that are externally being pulled low will source current because of the pull-ups. (See DC Electrical Characteristics: I

). Port 3 also serves the special features of

the 80C51 family, as listed below:

10 11 5 I RxD (P3.0): Serial input port 11 13 7 O TxD (P3.1): Serial output port 12 14 8 I INT0 (P3.2): External interrupt 13 15 9 I INT1 (P3.3): External interrupt 14 16 10 I T0 (P3.4): Timer 0 external input 15 17 11 I T1 (P3.5): Timer 1 external input 16 18 12 O WR (P3.6): External data memory write strobe 17 19 13 O RD (P3.7): External data memory read strobe

RST 9 10 4 I Reset: A high on this pin for two machine cycles while the oscillator is running, resets the

device. An internal diffused resistor to V

permits a power-on reset using only an external

capacitor to V

ALE 30 33 27 I/O Address Latch Enable: Output pulse for latching the low byte of the address during an

access to external memory. In normal operation, ALE is emitted at a constant rate of 1/6 the oscillator frequency. Note that one ALE pulse is skipped during each access to external data memory.

PSEN 29 32 26 O Program Store Enable: Read strobe to external program memory via Port 0 and Port 2. It

is activated twice each machine cycle during fetches from the external program memory. When executing out of external program memory two activations of PSEN

are skipped

during each access to external data memory. PSEN

is not activated (remains HIGH) during

no fetches from external program memory. PSEN

can sink/source 8 LSTTL inputs and can

drive CMOS inputs without external pull–ups.

EA 31 35 29 I External Access: If during a RESET, EA is held at TTL, level HIGH, the CPU executes out

of the internal program memory ROM provided the Program Counter is less than 8192. If during a RESET, EA

is held a TTL LOW level, the CPU executes out of external program

memory. EA

is not allowed to float.

XTAL1 19 21 15 I Crystal 1: Input to the inverting oscillator amplifier and input to the internal clock generator

circuits.

XTAL2 18 20 14 O Crystal 2: Output from the inverting oscillator amplifier.

NOTE:

To avoid “latch-up” effect at power-on, the voltage on any pin at any time must not be higher than V

+ 0.5V or VSS – 0.5V, respectively.

Phlips Semiconductors Product specification

80C652/83C652CMOS single-chip 8-bit microcontrollers

1996 Aug 15

Table 1. 8XC652/654 Special Function Registers

SYMBOL DESCRIPTION

DIRECT

ADDRESS

BIT ADDRESS, SYMBOL, OR ALTERNATIVE PORT FUNCTION MSB LSB

RESET VALUE

ACC* Accumulator E0H E7 E6 E5 E4 E3 E2 E1 E0 00H B* B register F0H F7 F6 F5 F4 F3 F2 F1 F0 00H DPTR:

DPH DPL

Data pointer (2 bytes) Data pointer high Data pointer low

83H 82H

00H 00H

AF AE AD AC AB AA A9 A8

IE*# Interrupt enable A8H EA ES1 ES0 ET1 EX1 ET0 EX0 0x000000B

BF BE BD BC BB BA B9 B8

IP*# Interrupt priority B8H – PS1 PS0 PT1 PX1 PT0 PX0 xx000000B

87 86 85 84 83 82 81 80

P0* Port 0 80H AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 FFH

97 96 95 94 93 92 91 90

P1*# Port 1 90H SDA SCL FFH

A7 A6 A5 A4 A3 A2 A1 A0

P2* Port 2 A0H A15 A14 A13 A12 A11 A10 A9 A8 FFH

B7 B6 B5 B4 B3 B2 B1 B0 P3* Port 3 B0H RD WR T1 T0 INT1 INT0 TXD RXD FFH PCON Power control 87H SMOD – – – GF1 GF0 PD IDL 0xxx0000B

9F 9E 9D 9C 9B 9A 99 98 S0CON*# Serial 0 port control 98H SM0 SM1 SM2 REN TB8 RB8 TI RI 00H S0BUF# Serial 0 data buffer 99H xxxxxxxxB

D7 D6 D5 D4 D3 D2 D1 D0 PSW* Program status word D0H CY AC F0 RS1 RS0 OV F1 P 00H S1DAT# Serial 1 data DAH 00H SP Stack pointer 81H 07H S1ADR# Serial 1 address DBH

 SLAVE ADDRESS 

GC 00H

S1STA# Serial 1 status D9H SC4 SC3 SC2 SC1 SC0 0 0 0 F8H

DF DE DD DC DB DA D9 D8 S1CON*# Serial 1 control D8H CR2 ENS1 STA STO SI AA CR1 CR0 00000000B

8F 8E 8D 8C 8B 8A 89 88 TCON* Timer control 88H TF1 TR1 TF0 TR0 IE1 IT1 IE0 IT0 00H TH1 Timer high 1 8DH 00H TH0 Timer high 0 8CH 00H TL1 Timer low 1 8BH 00H TL0 Timer low 0 8AH 00H TMOD Timer mode 89H GATE C/T M1 M0 GATE C/T M1 M0 00H

* SFRs are bit addressable. # SFRs are modified from or added to the 80C51 SFRs.

+ 17 hidden pages