Philips NORELCO S9733 User Manual

S9733

www.philips.com/support/ifu

empty page before TOC

English 6 Español 33

English

IMPORTANT SAFETY INSTRUCTIONS

When using an electric product, basic precautions should always be followed, including the following:

Read all instructions before using this product.

DANGER

To reduce the risk of electric shock:

Do not reach for a corded product that has fallen into water. Unplug immediately.

The power plug and the accessories connected to it are not for immersion or for use in shower.

Do not use an extension cord with this product.

Always unplug this product from the electrical outlet immediately after (re)charging.

Unplug and remove power cord from the product before cleaning.

The batteries used in this product may present a fire or chemical burn hazard if mistreated. Do not disassemble, heat above 100°C (212°F) or incinerate.

English

WARNING

To reduce the risk of burns, fire, electric shock, or injury to persons:

Close supervision is required when this product is used by, on, or near children, or persons with limited physical, sensory, or mental capabilities or invalids.

Use this product for its intended household use as described in this manual. Do not use attachments not recommended by Philips North America LLC.

Never operate this product if it has a damaged power cord or charging plug, if it is not working properly, if it has been dropped or damaged, or dropped into water while plugged in. For assistance call 1-800-243-3050.

Keep the product, cord and charging plug and any attachments away from heated surfaces.

Never drop or insert any object into any opening.

Do not use the adapter in or near a power outlet that contains an electric air freshener to prevent damage to the adapter.

Do not charge, clean or plug in product outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.

English

Always check cutters and combs before using the product. Do not use the product if cutters or combs are damaged, as injury may occur.

Always attach plug to product first, then to outlet. Be certain plug is inserted firmly into shaver up to mark indicated on plug. To disconnect, turn shaver off then remove power cord from outlet.

Keep the power cord dry at all times. Do not handle with wet hands.

Never put the product in direct sunlight or store at a temperature above 140°F (60°C).

To prevent possible damage to the power cord, do not wrap power cord around the product.

Do not attempt to open the product to remove or replace the built-in rechargeable battery.

Only use the power cord and other accessories supplied with the product.

SAVE THESE INSTRUCTIONS

IMPORTANT: The power plug contains a transformer. Do not cut off the power plug to replace it with another plug as this will cause a hazardous condition.

Contents

IMPORTANT SAFETY INSTRUCTIONS___ 6

English

SAVE THESE INSTRUCTIONS____________ 8 General description (Fig. 1)_______________ 9 Introduction______________________________ 10 The display_______________________________ 10 Charging__________________________________ 13 Using the product________________________ 15 Travel lock________________________________ 20 Cleaning and maintenance______________ 21 Replacement_____________________________ 27 Storage___________________________________ 28 Accessories_______________________________ 29 Assistance________________________________ 29 Disposal__________________________________ 29 Full Two-Year Warranty__________________ 30 45-DAY MONEY-BACK GUARANTEE____ 31

General description (Fig. 1)

1 Shaving unit with hair chamber 2 On/off button 3 Socket for small plug 4 SmartClick beard styler attachment 5 Comb for SmartClick beard styler

attachment

6 + and - buttons for personal comfort

settings 7 Personal comfort settings bar 8 Battery charge percentage 9 Battery symbol 10 Cleaning reminder 11 Travel lock symbol 12 Replacement reminder 13 Notification symbol 14 Power plug

English

15 Small plug 16 Travel pouch

Introduction

Congratulations on your purchase and welcome to Philips Norelco!

To fully benefit from the support that Philips Norelco offers, register your product at

www.norelco.com/register.

The display

Note: Before you use the shaver for the first time, remove the protective foil from the display.

Personal comfort settings

The shaver has a feature that allows you to personalize your settings. Depending on your personal shaving needs, choose between three settings, from low to high: slow: for an even more skin-friendly shave, medium: for a standard thorough shave, and fast: for a highpowered shave. When you press the button on the left or right of the display, the segment of the personal comfort settings bar that lights up shows the currently selected setting. To select a lower or higher setting, press the button on the left or right of the display.

English

Charging

When the shaver is charging, the battery charge percentage and the battery symbol flash white.

The battery charge is indicated by the battery charge percentage shown on the display.

Quick charge: When the battery symbol starts to flash quickly, the shaver contains enough charge for one shave.

Battery fully charged

When the battery is fully charged, the battery charge percentage lights up white continuously.

Note: This product can only be used without cord. When you press the on/off button during or after charging, you hear a sound to indicate that the shaver is still connected to the wall socket.

Note: When the battery is full, the display switches off automatically after 30 minutes.

Battery low

When the battery is almost empty, the battery charge indicator flashes orange and the shaver beeps.

English

Remaining battery charge

The remaining battery charge is indicated by the battery charge percentage shown on the display.

Cleaning reminder

Clean the shaver after every use for optimal performance (see 'Cleaning and maintenance'). When you switch off the shaver, the cleaning reminder flashes to remind you to clean the shaver.

Travel lock

You can lock the shaver when you are going to travel. The travel lock prevents the shaver from being switched on by accident.

Replacement reminder

For maximum shaving performance, we advise you to replace the shaving heads every year (see 'Replacement'). The shaver is equipped with a replacement reminder which reminds you to replace the shaving heads. The shaving unit symbol lights up white continuously, the arrows flash white and the shaver beeps to indicate that you have to replace the shaving heads.

Note: After replacing the shaving heads, you can reset the replacement reminder by pressing the on/off button for 7 seconds. If you

English

do not reset the replacement reminder, the shaver resets automatically after 9 shaves.

Notification symbol

Overheating

If the shaver overheats during charging, the notification symbol flashes orange. When this happens, the shaver switches off automatically. Charging continues once the temperature of the shaver has decreased to the normal level.

Blocked shaving heads

If the shaving heads are blocked, the notification symbol lights up orange continuously. The replacement reminder and the cleaning reminder flash white alternately and you hear a sound. In this case, the motor cannot run because the shaving heads are soiled or damaged.

If the shaving heads are soiled, you have to clean them. If the shaving heads are damaged, you have to replace them.

Charging

Charging, recharging, or using the product

at temperatures below 40°F (4.5°C) or

higher than 95°F (35°C) adversely affects

the lifespan of the battery.

Do not charge the shaver in a pouch or

travel case.

The power plug transforms 100-240V AC to

less than 24V DC.

English

Charge the shaver before you use it for the first time and when the display indicates that the battery is almost empty. The battery charge is indicated by the lights of the battery charge indicator on the display.

When you connect the shaver to the wall socket, you hear a sound.

Charging takes approx. 1 hour. A fully charged shaver has a shaving timeof up to 60 minutes.

Note: You cannot use the product while it is charging.

Charging with the power cord

1 Make sure the shaver is switched off.

2 Put the small plug in the shaver and

connect the power plug to any 100V to

240V AC outlet. Use only the power cord

provided.

The display of the shaver indicates that the

shaver is charging. 3 After charging, remove the power plug from

the wall outlet and pull the small plug out of

the shaver.

Note: An adapter plug may be necessary for cord usage in some foreign countries. Use an attachment plug adapter of the proper configuration for power outlet.

English

Using the product

Always check the shaver and all accessories before use. Do not use the shaver or any accessory if it is damaged, as this may cause injury. Always replace a damaged part with one of the original type.

This symbol indicates that the shaver can be used in the bath or shower.

Use this shaver for its intended household

use as described in this manual.

For hygienic reasons, the shaver should

only be used by one person.

Trimming is easier when the skin and hair

are dry.

Note: This shaver is waterproof. It is suitable for use in the bath or shower and for cleaning under the tap. For safety reasons, the shaver can therefore only be used without charging cord.

Put it to the test

21 Day Trial and Conversion Process. It is a

fact that your skin and beard need time to

adjust to a new grooming system.

Use your new shaver exclusively for 3 weeks

to fully enjoy the closeness of a Philips

Norelco shave.

English

At first you may not get as close a shave as

you expect, or your face may even become

slightly irritated. This is normal since your

beard and skin will need time to adjust.

Invest 3 weeks and you'll soon experience

the full joy of your new shaver.

Stick with it! If you alternate shaving

methods during the adjustment period, it

may make it more difficult to adapt to the

Philips Norelco shaving system.

If you are still not convinced after 21 days,

Philips Norelco will refund you the full

purchase price as long as the request is

received within 45 days of purchase.

Switching the product on and off

1 To switch on the shaver, press the on/off

button once.

The display lights up for a few seconds. 2 To switch off the shaver, press the on/off

button once.

The display lights up for a few seconds and

shows the remaining battery charge.

Shaving

Shaving tips

Selectyour personal comfort settings (see

‘The display’).

For the best results on skin comfort, pre-

trim your beard if you have not shaved for 3

days or longer.

Dry shaving

1 Switch the shaver on.

English

2 Stretch your skin with your free hand so

blades can lift and cut whiskers. Gently

press shaver to skin so the floating heads

can follow the contours of your face.

Note: Do not press too hard. Too much

pressure can pinch the skin into the combs. 3 Switch off and clean the shaver after each

use.

The display lights up for a few seconds to

show the battery status.

Wet shaving

For a more comfortable shave, you can also use this shaver on a wet face with shaving foam or shaving gel.

1 Apply some water to your skin.

2 Apply shaving foam or shaving gel to your

skin.

3 Rinse the shaving unit under the tap to

ensure that the shaving unit glides smoothly

over your skin. 4 Switch the shaver on.

English

5 Move the shaving heads over your skin in

circular movements to catch all hairs

growing in different directions. Make sure

each shaving head is fully in contact with

the skin. Exert gentle pressure for a close,

comfortable shave.

Note: Do not press too hard, this can cause

skin irritation.

Note: Rinse the shaving unit regularly to

ensure that it continues to glide smoothly

over your skin.

6 Dry your face. 7 Switch off the shaver and clean it after each

use.

Note: Make sure that you rinse all foam or shaving gel off the shaver.

Using click-on attachments

Using the beard styler attachment with comb

You can use the beard styler attachment with the comb attached to style your beard at one fixed setting, but also at different length settings. You can also use it to pre-trim any long hairs before shaving for a more comfortable shave.

The length settings on the beard styler attachment correspond to the remaining hair length after cutting and range from 1 to 5mm (3/64 - 3/16in).

English

1 Attach the attachment to the product

('click').

2 Slide the comb straight into the guiding

grooves on both sides of the beard styler

attachment (‘click’).

3 Press the length selector and then push it

to the left or right to select the desired hair

length setting.

4 Switch on the product.

5 Move the product upwards while you exert

gentle pressure. Make sure the front of the

comb is in full contact with the skin. 6 Clean the attachment after use.

Using the beard styler attachment without comb

You can use the beard styler attachment without the comb to contour your beard, moustache, sideburns or neckline to a length of 0.5mm (1/32 in).

1 Pull the comb off the beard styler

attachment.

English

Note: Grab the comb in the center to pull it

off the beard styler attachment. Do not pull

at the sides of the comb.

2 Switch on the product.

3 Hold the beard styler attachment

perpendicular to the skin and move the

product downwards while you exert gentle

pressure.

4 Clean the attachment after use.

Travel lock

You can lock the shaver when you are going to travel to prevent it from turning on accidentally.

Activating the travel lock

1 Press the on/off button for 3 seconds to

enter the travel lock mode.

While you activate the travel lock, the travel

lock symbol lights up white continuously.

When the travel lock is activated, the

appliance produces a sound and the travel

lock symbol flashes.

Deactivating the travel lock

1 Press the on/off button for 3 seconds.

English

+ 44 hidden pages

Philips NORELCO S9733 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual