Philips Norelco 6000, Norelco S6880, Norelco S6810, Norelco S6850, Norelco S6820 Series Manual
S6880, S6850,
S6820, S6810
Tripleh eader s haver
BC
S6850
S6880
S6820
S6850
S6880
S6820
S6810
S6810
3
4
2
7
17
18
8
10
11
12
13
14
15
9
19
16
20
S6810
S6850
1
6
5
empty page before TOC
English 6
Español 37
English
6
IMPORTANT SAFETY INSTRUCTIONS
When using an electric product, basic
precautions should always be followed,
including the following:
Read all instructions before using this
product.
DANGER
To reduce the risk of electric shock:
-
Do not reach for a corded product or
charging stand that has fallen into water.
Unplug immediately from the power outlet.
-
Keep the power cord and charging stand
dry.
-
Do not place or store the product or
charging stand where it can fall or be pulled
into a tub or sink. Do not place or drop the
product or charging stand into water or
other liquid.
-
Except when charging, always unplug this
product from the power outlet immediately
after use.
-
Remove power cord from power outlet and
product before cleaning.
-
Plug power cord directly into power outlet.
Do not use an extension cord.
English
WARNING
To reduce the risk of burns, fire, electric
shock, or injury to persons:
-
Close supervision is required when this
product is used by, on, or near children, or
persons with limited physical, sensory, or
mental capabilities or invalids.
-
Use this product only for its intended
household use as described in this manual.
Do not use attachments not recommended
by Philips North America LLC.
-
Never operate the product or charging
stand if it has a damaged power cord, if it is
not working properly, after it has been
dropped or damaged, or after the product
or power cord has been dropped into water.
For assistance call 1-800-243-3050.
-
Keep the power cord away from heated
surfaces.
-
Never drop or insert any object into any
opening.
-
Do not use the power cord in or near a
power outlet that contains an electric air
freshener to prevent damage to the power
cord.
-
Do not charge or plug in product or
charging stand outdoors or operate where
aerosol (spray) products are being used or
where oxygen is being administered.
English
7
8
English
-
Always check cutters, cutting unit and
guards before using the product. Do not use
the product if cutters, cutting unit or guards
are damaged, as injury may occur.
-
Always attach power cord to product or
charging stand first, then to power outlet.
To disconnect, set all controls to 'off'
position. Then remove power cord from
power outlet.
-
Unplug power cord before plugging in or
unplugging the product.
-
Only use the power cord and other
accessories supplied with the product.
-
Do not attempt to open the product to
remove or replace the built-in rechargeable
battery.
-
The batteries used in this product may
present a fire or chemical burn hazard if
mistreated. Do not disassemble, heat above
100°C (212°F) or incinerate.
IMPORTANT: The power plug contains a
transformer. Do not cut off the power plug to
replace it with another plug as this will cause a
hazardous condition.
SAVE THESE INSTRUCTIONS
Contents
IMPORTANT SAFETY INSTRUCTIONS___ 6
General description (Fig. 1)_______________ 9
Introduction______________________________ 10
The display_______________________________ 10
Charging__________________________________ 13
Using the shaver_________________________ 15
Using click-on attachments______________ 19
Travel lock________________________________ 23
Cleaning and maintenance______________ 24
Replacement_____________________________ 31
Storage___________________________________ 32
Accessories_______________________________ 33
Assistance________________________________ 33
Disposal__________________________________ 33
Full Two-Year Warranty__________________ 34
45-DAY MONEY-BACK GUARANTEE____ 35
General description (Fig. 1)
1 Click-on precision trimmer (S6880, S6850,
S6820 only)
2 Protective cap for shaving unit (S6880,
S6850 only)
3 Click-on beard styler (S6810 only)
4 Comb for beard styler (S6810 only)
5 Click-on nose trimmer (S6850 only)
6 Protective cap for nose trimmer (S6850
only)
7 Shaving unit with hair chamber
8 On/off button
9 SkinGuard mode
10 Cleaning reminder
11 Replacement reminder
12 Travel lock symbol
13 'Unplug for use' reminder
14 Battery charge indicator
English
9
English
10
15 Socket for small plug
16 Charging stand (S6810 only)
17 Power plug
18 Small plug
19 Cleaning brush
20Travel case (S6820, S6810 only)
Note: The accessories supplied may vary for
different products. The box shows the
accessories that have been supplied with your
product.
Introduction
Congratulations on your purchase and
welcome to Philips Norelco!
To fully benefit from the support that Philips
Norelco offers, register your product at
www.norelco.com/register.
The display
Battery charge indicator
Quick charge: When the battery is empty and
you connect the shaver to an electrical outlet,
the lights of the battery charge indicator light
up white one after the other repeatedly. When
the battery contains enough energy for one
shave, the bottom light of the battery charge
indicator starts flashing white slowly.
As charging continues, each light will blink and
then light up continuously to indicate what
level the battery has been charged.
Battery fully charged
When the battery is fully charged, all lights of
the battery charge indicator light up white
continuously.
Note: When you press the on/off button while
the shaver is still connected to the power
outlet, the 'unplug for use' symbol lights up to
remind you to disconnect the shaver from the
power outlet before you can switch it on.
Note: When the battery is full, the display
switches off automatically after 30 minutes.
Battery low
When the battery is almost empty, the bottom
light of the battery charge indicator flashes
orange. At this point there is enough energy
left for one shave.
English
11
English
12
Remaining battery charge
The remaining battery charge is indicated by
the lights of the battery charge indicator that
light up continuously.
’Unplug for use’ reminder
The ‘unplug for use’ symbol flashes to remind
you to disconnect the shaver from the power
outlet before you can switch it on.
Cleaning reminder
Clean the shaver after every use for optimal
performance (see 'Cleaning and maintenance').
When you switch off the shaver, the cleaning
reminder flashes to remind you to clean the
shaver.
Travel lock
When you are going to travel, you can lock the
shaver to prevent it from accidentally turning
on.
Replacement reminder
For maximum shaving performance, replace
the shaving heads every year. The shaver is
equipped with a replacement reminder that
flashes to remind you to replace the shaving
heads.
Note: After replacing the shaving heads, you
can reset the replacement reminder by
pressing the on/off button for 7 seconds. If you
do not reset the replacement reminder, the
shaver resets automatically after 9 shaves.
SkinGuard mode
This mode reduces the rotation speed of the
shaver (see 'Shaving with SkinGuard mode').
Charging
-
Charging, recharging, or using the product
at temperatures below 40°F (4.5°C) or
higher than 95°F (35°C) adversely affects
the lifespan of the battery.
-
Do not charge the shaver in a pouch or
travel case.
-
The power plug transforms 100-240V AC to
less than 24V DC.
Charge the shaver before you use it for the first
time and when the display indicates that the
battery is almost empty.
English
13
English
14
Charging takes approx. 1 hour. A fully charged
shaver has a shaving timeof up to 50 minutes.
Note: You cannot use the shaver while it is
charging.
Quick charge
After approx. 5 minutes of charging, the shaver
contains enough power for one shave. The
bottom light of the battery charge indicator
starts flashing white slowly when the quick
charge is finished.
Charging with the power cord
1 Make sure the shaver is switched off.
2 Put the small plug in the shaver and
connect the power plug to any 100V to
240V AC outlet. Use only the power cord
provided.
The display of the shaver indicates the
product is charging.
3 After charging, remove the power plug from
the wall outlet and pull the small plug out of
the shaver.
Charging in the charging stand (S6810 only)
Note: The shaver can also be charged with the
power cord (see 'Charging with the power
cord').
1 Make sure the shaver is switched off.
2 Insert the small plug into the charging stand
connect the power plug to any 100V to
240V AC outlet. Use only the power cord
provided.
3 Put the shaver in the charging stand.
4 After charging, remove the power plug from
the wall outlet and pull the small plug out of
the charging stand.
Note: An adapter plug may be necessary for
cord usage in some foreign countries. Use an
attachment plug adapter of the proper
configuration for power outlet.
Using the shaver
Always check the shaver and all accessories
before use. Do not use the shaver or any
accessory if it is damaged, as this may cause
injury. Always replace a damaged part with
one of the original type.
This symbol indicates that the shaver can be
used in the bath or shower.
-
Use this shaver for its intended household
use as described in this manual.
-
For hygienic reasons, the shaver should
only be used by one person.
-
Trimming is easier when the skin and hair
are dry.
English
15
English
16
Put it to the test
-
21 Day Trial and Conversion Process. It is a
fact that your skin and beard need time to
adjust to a new grooming system.
-
Use your new shaver exclusively for 3 weeks
to fully enjoy the closeness of a Philips
Norelco shave.
-
At first you may not get as close a shave as
you expect, or your face may even become
slightly irritated. This is normal since your
beard and skin will need time to adjust.
Invest 3 weeks and you'll soon experience
the full joy of your new shaver.
-
Stick with it! If you alternate shaving
methods during the adjustment period, it
may make it more difficult to adapt to the
Philips Norelco shaving system.
-
If you are still not convinced after 21 days,
Philips Norelco will refund you the full
purchase price as long as the request is
received within 45 days of purchase.
Switching the shaver on and off
1 To switch the shaver on or off, press the
on/off button once.
The display lights up for a few seconds to
show the battery status.
Note: This shaver is waterproof. It is suitable
for use in the bath or shower and for cleaning
under the tap. For safety reasons, the shaver
can only be used without charging cord.
Shaving
English
-
For the best results on skin comfort, pre-
trim your beard if you have not shaved for 3
days or longer.
Dry shaving
1 Switch the shaver on.
2 Move the shaving heads over your skin in
circular movements to catch all hairs
growing in different directions. Make sure
each shaving head is fully in contact with
the skin. Exert gentle pressure for a close,
comfortable shave.
Note: Do not press too hard, as this can
cause skin irritation.
3 Switch off and clean the shaver after each
use.
The display lights up for a few seconds to
show the battery status.
Wet shaving
For a more comfortable shave, you can also
use this shaver on a wet face with shaving
foam or shaving gel.
1 Apply some water to your skin.
17
18
English
2 Apply shaving foam or shaving gel to your
skin.
3 Rinse the shaving unit under the tap to
ensure that the shaving unit glides smoothly
over your skin.
4 Switch on the shaver.
5 Move the shaving heads over your skin in
circular movements to catch all hairs
growing in different directions. Make sure
each shaving head is fully in contact with
the skin. Exert gentle pressure for a close,
comfortable shave.
Note: Do not press too hard, as this can
cause skin irritation.
Note: Rinse the shaving unit regularly to
ensure that it continues to glide smoothly
over your skin.
6 Dry your face.
7 Switch off and clean the shaver after each
use (see 'Cleaning and maintenance').
Note: Make sure that you rinse all foam or
shaving gel off the shaver.
Shaving with SkinGuard mode
This mode reduces the rotation speed of the
shaver.
1 Switch on the shaver.
2 Press the SkinGuard button once if you
want to shave at a lower rotational speed.
3 Move the shaving heads over your skin in
circular movements to catch all hairs
growing in different directions. Make sure
each shaving head is fully in contact with
the skin. Exert gentle pressure for a close,
comfortable shave.
Note: Do not press too hard, as this can
cause skin irritation.
4 Switch off the SkinGuard mode and return
the shave to normal speed, by pressing the
SkinGuard button once.
Note: Shaver runs at normal speed
automatically when switched on for each
new shave.
Using click-on attachments
Note: The accessories supplied may vary for
different products. The box shows the
accessories that have been supplied with your
product.
English
19
Removing or attaching click-on attachments
1 Make sure the shaver is switched off.
English
20
2 Pull the attachment straight off the
appliance.
Note: Do not twist the attachment while you
pull it off the appliance.
3 Insert the lug of the attachment into the slot
in the top of the appliance. Then press
down the attachment to attach it to the
appliance (‘click’).
Using the precision trimmer attachment (S6820, S6850, S6880 only)
You can use the precision trimmer attachment
to touch up your beard, sideburns and
mustache.
1 Attach the trimmer to the product ('click').
2 Switch on the product.
3 Hold the trimmer perpendicular to the skin
and move it downwards while exerting
gentle pressure.
4 Switch off and clean the attachment after
use.
Using the beard styler attachment with comb (S6810 only)
You can use the beard styler with the comb
attached to style your beard at one fixed
setting or at different length settings. You can
1
2
English
also use it to pre-trim any long hairs before
shaving for a more comfortable shave.
The length settings on the beard styler
attachment correspond to the remaining hair
length after cutting and range from 1 to 5mm
(3/64 - 3/16in).
1 Attach the beard styler to the product
('click').
2 Slide the comb straight into the guiding
grooves on both sides of the beard styler
attachment (‘click’).
3 Press the length selector and then push it
to the left or right to select the desired hair
length setting.
4 Switch on the product.
5 Move the product upwards while you exert
gentle pressure. Make sure the front of the
comb is in full contact with the skin.
If cut hairs accumulate in the comb, switch
the product off, remove comb and blow
and/or shake hair out of the comb.
6 Clean the attachment after use.
Using the beard styler attachment without comb
You can use the beard styler attachment
without the comb to contour your beard,
mustache, sideburns or neckline to a length of
0.5mm (1/32 in).
21
English
22
1 Pull the comb off the beard styler
attachment.
Note: Grab the comb in the center to pull it
off the beard styler attachment. Do not pull
at the sides of the comb.
2 Switch on the product.
3 Hold the beard styler perpendicular to the
skin and move the product downwards
while you exert gentle pressure.
4 Clean the attachment after use.
Using the nose/ear trimmer attachment (S6850 only)
You can use the nose/ear trimmer attachment
to trim your nose and/or ear hair.
Trimming nose hair
When trimming nose hair, make sure your
nostrils are clean.
1 Attach the nose trimmer to the product
('click').
2 Switch on the product.
3 Carefully insert the nose trimmer into one of
your nostrils.
Do not insert the nose trimmer more than
0.5cm into your nostrils.
English
4 Slowly move the nose trimmer around to
remove all unwanted hairs in your nostrils.
5 Clean the attachment after each use.
23
Trimming ear hair
When trimming ear hair, make sure your outer
ear channels are clean and free from wax.
1 Attach the nose trimmer to the product
('click').
2 Switch on the product.
3 Slowly move the nose trimmer along the rim
of the ear to remove hairs that stick out
beyond the rim.
4 Insert the nose trimmer into the outer ear
channel.
Do not insert the nose trimmer more than
0.5cm into your ear channel, as this could
damage the eardrum.
5 Slowly turn the nose trimmer around to
remove all unwanted hairs from your outer
ear channel.
6 Clean the attachment after each use.
Travel lock
You can lock the shaver when you are going to
travel to prevent it from turning on
accidentally.
Loading...