Philips 7100, Norelco HAIRCLIPPER 7100, Norelco HC7452 Instructions Manual
3 Turn the Adjustable Wheel Hair Length
Setting Selector to the desired setting (fig. 7).
The Clipper can cut hair up to 24 different
lengths. See table below.
4 The remaining hair length is indicated in
millimeters on the adjustable wheel.
When you are clipping for the first time,
start at the maximum clipping length setting
(23mm/7/8 in.) to familiarize yourself with the
appliance and prevent accidentally trimming
hairs too short. As you become familiar with the
settings, adjust the Hair Length Selector to desired
trimming length.
5 Make sure that the flat part of the comb is
always in full contact with the scalp to obtain
an even result (fig. 8).
6 Since all hairs do not grow in the same
direction, move the appliance slowly over the
crown from different directions (i.e. upwards,
downwards and across) to achieve an even
result.
7 Always move the appliance against the
direction of hair growth.
8 Make overlapping passes over the head to
ensure that all hair that should be cut has
been cut.
9 For best results with curly, sparse or long
hair, use a styling comb to guide the hair
towards the Clipper.
10 Switch the Clipper off regularly during
clipping and remove the hair clipping comb
to blow and/or shake out hair that has
accumulated.
TIP: Write down the settings you have used to create
a certain hairstyle as a reminder for future clipping
sessions.
Clipping without hair clipping comb
w Use the Clipper without a comb to clip hair
very close to the skin (0.5mm/1/32 inch) or to
contour the neckline and area around the ears.
1 Remove the hair clipping comb by pressing
and sliding the comb off the Clipper (fig. 9).
Be careful when you are clipping without comb
attachment as when the Clipper is turned on it
will remove every hair it touches.
2 To contour the hairline around the ears,
comb the hair ends over the ears.
3 Tilt the Clipper in such a way that only
one edge of the cutter blades touches the
hair ends when you shape the contours
around the ears.
Only cut the hair ends. The hairline should be
close to the ear.
4 To contour the nape of the neck or
sideburns, turn the Clipper and make
downward strokes (fig. 10).
5 Move the Clipper slowly and smoothly
following the natural hairline.
Cleaning
w Clean the attachments after each use.
w Always switch Clipper OFF, unplug and remove
power supply cord from Clipper before
cleaning.
w Do not use compressed air, abrasive cleaning
agents, scourers or aggressive liquids such as
alcohol, benzene, bleach or acetone to clean
the Clipper and attachments.
w Never clean, replace or remove Clipper
attachments with motor ON.
w Never rinse or immerse the Clipper in water
or any other liquid.
w Do not apply pressure to cutters.
w Do not touch cutters with hard objects as this
may damage them.
During Use:
w If cut hairs have accumulated in the comb
area, remove hairs by shaking, blowing or using
cleaning brush provided.
A Hair Clipping Comb
B Cutting Unit
C Adjustable Wheel Hair Length
Setting Selector
D On/Off Button
E Turbo Button
F Charging Light
G Socket for Appliance Plug
H Cleaning Brush
I Adaptor
J Appliance Plug
K Storage Case
Full Two-Year Warranty
45-Day Money-Back Guarantee
Put It To The Test
Like many new products, your Philips Norelco Hair
Clipper may take a little getting used to. If you are
using an electric Clipper for the first time, or if
you’ve been using a different brand, take the time
to acquaint yourself with your new Hair Clipper.
Your Hair Clipper features a double-sharpened
cutting element with reduced friction as well as
Turbo power to boost cutting speed for a perfect
cut even on the thickest hair.
Throw your scissors away and put your new
Hair Clipper to the test. We guarantee precise
results or Philips Norelco will refund you the full
purchase price as long as the request is received
within 45 days of purchase.
To Charge/Recharge
w Fully charge Clipper before using for the first
time or after non-use for a long period of time.
w Charging, recharging or using Clipper at
temperaturesbelow 40˚Forhigherthan95˚F
adversely affects lifespan of the battery.
1 Be certain Clipper is OFF.
2 Inser t the appliance plug directly into the
Clipper (fig. 1) and plug the adapter into any
120V AC outlet. Use only the cord provided.
3 The Charging Light on the appliance will
blink green to indicate the Clipper is charging
(fig. 2).
w It will take approximately 1 hour to fully
charge the Clipper for a cordless clipping
time of up to 120 minutes.
4 When the batter y is fully charged, the
charging light lights up green continuously
for 30 minutes and then turns off (fig. 3).
5 Disconnect the cord and unplug from
electrical outlet.
Turbo Power
w Simply press the Turbo Button for a turbo
power boost for fast results, even on the
thickest hair. The memory function will
remember the last used setting.
Corded Hair Clipping
wClipper does not recharge during corded
clipping.
1 Connect cord provided to Clipper (fig. 1) and
plug Clipper into electrical outlet.
2 If battery is completely empty, wait a few
minutes before switching clipper ON.
3 Turn Clipper ON to begin clipping (fig. 4).
4 When finished clipping, switch Clipper OFF
and unplug.
Cordless Hair Clipping
1 Charge according to directions. Unplug
Clipper from outlet and remove cord.
2 Turn Clipper ON to begin clipping (fig. 4).
3 If the charge runs low while clipping, the
charging light will blink orange (fig. 2).
4 If the charge runs out while clipping, simply
connect cord provided to Clipper and outlet
to continue clipping.
Hair Clipping
wUse this Clipper for its intended household
use as described in this manual.
wMake sure that the appliance is fully charged
before you start clipping hair.
w Before you start clipping, make sure that the
head of the person whose hair you are cutting
is at the same level as your chest so that all
parts of his/her head are clearly visible and
within easy reach.
w Only use the appliance on clean, dry hair.
w Do not use on freshly washed hair.
w Before you begin, comb the hair in the direction
of growth (fig. 5).
w To achieve optimal clipping results, always move
the appliance slowly through the hair against
the direction of hair growth.
Clipping with hair clipping comb
1 Be cer tain the Clipper is in the OFF position.
2 Slide the hair clipping comb into the guiding
grooves on both sides of Clipper and push
until you hear it ‘click’ into place (fig. 6).
Make sure the comb locks properly into position.
After Each Use:
1 Make sure the Clipper is switched OFF
and disconnected from the electrical outlet.
2 Remove the hair clipping comb by pressing
and sliding the comb off the Clipper (fig. 9).
3 Clean the comb with the brush supplied or
rinse under warm water (fig. 11).
4 Press the release button (1) and remove the
cutting unit (2) (fig. 12).
5 Clean the cutting unit with the brush
supplied or rinse under warm water (fig. 13).
6 Clean the inside of the Clipper with the
brush supplied (fig. 14).
7 Shake off any excess water and allow to
air dry.
8 Reattach cutting unit by inser ting the notch
of the cutting unit into the guiding slot.
9 Push the cutting unit back onto the Clipper.
10 Clean the handle and the adapter with a
soft, dry cloth.
NOTE: The Clipper does not need any lubrication.
Replacing the Cutting Unit
If your cutters become damaged or worn, do
not continue using the Clipper. Replace cutters
immediately.
1 Press the release button (1) and remove the
cutting unit (2) (fig. 12).
2 Place the notch of the new cutting unit in
the guiding slot (1) and push the cutting unit
onto the Clipper (2) (fig. 15). You will hear
a ‛click’.
This Clipper has no other user-serviceable parts.
For assistance call 1-800-243-3050.
Assistance
For assistance, call toll free:
1-800-243-3050
or visit our website:
www.philips.com/support
Online information is available 24 hours a day,
7 days a week.
Storage
w Be sure Clipper is switched OFF. Remove cord
from outlet and Clipper before storing in a
safe, dry location where it will not be crushed,
banged, or subject to damage.
w Do not wrap cord around Clipper when
storing.
w Store cord in a safe location where it will not
be cut or damaged.
w Do not place or store Clipper where
it can fall or be pulled into a tub or sink, water
or other liquid while plugged in.
Battery Removal
w This Philips Norelco Clipper contains a
rechargeable Lithium-Ion battery which must
be disposed of properly (fig. 16).
w Battery should only be removed when
Clipper is to be discarded.
w For assistance, visit our website,
www.philips.com/support or call
toll free: 1-800-243-3050.
1 Unplug electrical cord from outlet and
Clipper before dismantling Clipper.
2 Allow Clipper to run until the battery is
empty/depleted.
3 Switch Clipper OFF.
4 Remove the hair clipping comb and cutting
unit from the handle.
5 Press the release button (1) and remove the
cutting unit (2) (fig. 17).
6 Insert the screwdriver between the motor
unit and the back panel of the appliance.
Press down the screwdriver as far as it will
go (fig. 18).
7 Tilt the handle of the screwdriver
downwards (1) and separate the back panel
from the appliance (2) (fig. 19).
8 Remove the back panel. Pull the bottom
part of the printed circuit board with the
rechargeable batteries attached from the
appliance (fig. 20).
9 Cut the wires to separate the rechargeable
batteries from the appliance (fig. 21).
IMPORTANT
SAFETY
INSTRUCTIONS
When using an electrical appliance, basic safety
precautions should always be followed, including
the following:
Read all instructions before using this
appliance.
DANGER
To reduce the risk of electric shock:
1. Do not reach for a clipper that has fallen into
water. Unplug immediately.
2. Use clipper only in dry condition. Do not use
while bathing or in a shower.
3. Do not submerge clipper in water.
4. Do not place or store clipper where it can
fall or be pulled into a tub or sink. Do not
place in or drop into water or other liquid.
5. Always unplug this clipper from the electrical
outlet immediately after using, except when
clipper is (re)charging.
6. Unplug clipper before cleaning.
7. When discarding clipper, unplug clipper to
remove rechargeable battery. See Battery
Removal instructions.
8. The batteries used in this device may present
a fire or chemical burn hazard if mistreated.
Do not disassemble, heat above 100°F
(212°F) or incinerate.
WARNING
To reduce the risk of burns, fire, electric
shock or injury to persons:
1. Close supervision is necessary when
this appliance is used by, on, or near children
or invalids.
2. Use this clipper for its intended household
use as described in this manual. Do not use
attachments not recommended by Philips
Electronics North America Corporation.
3. Never operate this clipper if it has a
damaged cord or plug, if it is not working
properly, if it has been dropped, damaged, or
dropped into water. For assistance visit our
website www.philips.com/norelco or call
1-800-243-3050.
4. Do not rinse or immerse the clipper handle
in water or any other liquid.
5. Keep the clipper, cord and any attachments
away from heated surfaces.
6. Never drop or insert any object into any
opening.
7. Do not operate, charge or plug in clipper
outdoors or where aerosol (spray) products
are being used or where oxygen is being
administered.
8. Always check cutters, cutting unit and comb
before using the clipper. Do not use the
clipper if cutters, cutting unit or comb are
damaged, as injury may occur.
9. Always attach plug to clipper first, then to
outlet. To disconnect, switch Clipper OFF,
then remove plug from outlet.
10. To prevent possible damage to the cord, do
not wrap cord around the clipper.
11. Use only the cord provided to charge and
(re)charge clipper.
12. Never put clipper in direct sunlight or store
at a temperature above 140°F.
13. This clipper is for use on human hair only.
Do not use this clipper for any other
purpose.
14. Only use the power plug and other
accessories supplied with the clipper.
SAVE THESE
INSTRUCTIONS
IMPORTANT: The power plug contains
a transformer. Do not cut off the power
plug to replace it with another plug as this
will cause a hazardous condition.
Registration
Congratulations on your purchase and welcome
to Philips Norelco!
To fully benefit from the support that Philips
Norelco offers, register your product at
www.norelco.com/register
10 Do not attempt to replace battery. Insulate
battery ends by covering with tape and/or
place battery in a small plastic bag.
11 Discard your Clipper. Do not attempt to
plug electrical cord into the outlet or
recharge the Clipper after the battery has
been removed.
12 Contact your local town or city officials
for battery disposal information or call
1-800-8-BATTERY or www.rbrc.com for
battery drop-off locations.
A
C
D
F
I
H
J
K
G
B
E
Features
1 2 3
4 5 6
13
12
11
15
14
mm
mm
mm
mm
mm
7 8 9
10 11
1
2
12
13 14
1
2
15
1
2
17 18
2
1
19 20
16
4222 002 8400 2
HC7452
Rechargeable
Cordless/Cord
Full Two-Year Warranty
Philips Electronics North America Corporation warrants each new Philips
Norelco product, Model HC7452 (except cutters and comb) against
defects in materials or workmanship for a period of two years from the
date of purchase, and agrees to repair or replace any defective product
without charge.
IMPORTANT: This warranty does not cover damage resulting from
accident, misuse or abuse, lack of reasonable care, the affixing of any
attachment not provided with the product or loss of parts or subjecting
the product to any but the specific voltage.* Use of unauthorized
replacement parts will void this warranty.
PHILIPS ELECTRONICS NORTH AMERICA CORPORATION
WILL NOT PAY FOR WARRANTY SERVICE PERFORMED BY
A NON-AUTHORIZED REPAIR SERVICE AND WILL NOT
REIMBURSE THE CONSUMER FOR DAMAGE RESULTING FROM
WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZED
REPAIR SERVICE.
NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
In order to obtain warranty service, simply go to www.philips.com/
norelco or call 1-800-243-3050 for assistance. It is suggested that for
your protection you return shipments of product by insured mail,
insurance prepaid. Damage occurring during shipment is not covered by
this warranty. NOTE: No other warranty, written or oral, is authorized
by Philips Electronics North America Corporation. This warranty gives
you specific legal rights, and you may also have other rights which vary
from state to state. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above exclusion and
limitations may not apply to you.
*Read enclosed instructions carefully.
Manufactured for:
Philips Consumer Lifestyle
A Division of Philips Electronics North America Corporation
P.O. Box 10313, Stamford, CT 06904
This symbol on the product’s nameplate means it is
listed by Underwriters’ Laboratories, Inc.
Norelco is a Registered Trademark of Philips Electronics
North America Corporation.
PHILIPS is a Registered Trademark of Koninklijke Philips N.V.
© 2013 Philips Electronics North America Corporation. All Rights Reserved.
ENGLISH
45-DAY MONEY-
BACK GUARANTEE
If you are not fully satisfied with your Philips Norelco
Clipper, send the product back and we’ll refund you the
full purchase price. The Clipper must be shipped
prepaid by insured mail, insurance prepaid, have
the original sales receipt, indicating purchase
price and date of purchase, and the money-back
guarantee return authorization form enclosed.
We cannot be responsible for lost mail.
The Clipper must be postmarked no later than
45 days after the date of purchase. Philips
Norelco reserves the right to verify the purchase
price of the product and limit refunds not to
exceed suggested retail price.
To obtain money-back guarantee return
authorization form, call 1-800-243-3050 for
assistance.
Delivery of refund check will occur 6–8 weeks AFTER
receipt of returned product.
Register your product and get support at
www.norelco.com/register
Always here to help you
Question?
Contact
Philips
Norelco
Question?
Contact
Philips
Norelco
21
Trimming Length Settings Table
1mm – 3/64 in.
2mm – 5/64 in.
3mm – 1/8 in.
4mm – 5/32 in.
5mm – 3/16 in.
6mm – 1/4 in.
7mm – 9/32 in.
8mm – 5/16 in.
9mm – 3/8 in.
10mm – 13/32 in.
11mm – 7/16 in.
12mm – 15/32 in.
13mm – 1/2 in.
14mm – 9/16 in.
15mm – 5/8 in.
16mm – 21/32 in.
17mm – 11/16 in.
18mm – 23/32 in.
19mm – 3/4 in.
20mm – 25/32 in.
21mm – 13/16 in.
22mm – 55/64 in.
23mm – 7/8 in.
HAIRCLIPPER 7100
SERIES 7000
Loading...