Philips Norelco S7720, Norelco 7700, Norelco 7500 User Manual

S7720
Rechargeable Cordless Tripleheader Shaver
SHAVER 77007700
SERIES 700 0SERIES 700 0
SHAVER 75007500
SERIES 700 0SERIES 700 0
Always here to help you
Contact
Philips
Norelco
Contact
Philips
Norelco
Register your product and get support at
www.norelco.com/register
2
S7720
ENGLISH 4
ESPAÑOL 44
Congratulations on your purchase and welcome to Philips Norelco!
To fully benefit from the support that Philips Norelco offers, register your product at www.norelco.com/register
¡Bienvenido a Philips Norelco y felicitaciones por su compra!
Para utilizar los servicios de asistencia técnica de Philips Norelco, registre su producto en www.norelco.com/register
North America Corporation.
3. Never operate this shaver/SmartClean System if it has a damaged cord or charging plug, if it is not working properly, if it has been dropped or damaged, or dropped into water while plugged in. For assistance call 1-800-243-3050.
4. Keep the shaver/SmartClean System, cord and charging plug away from heated surfaces.
5. Never drop or insert any object into any opening.
6. Do not clean, charge or plug in shaver/SmartClean System outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
7. Do not use this shaver with a damaged or broken comb, as facial injury may occur.
8. Always attach plug to shaver/SmartClean System first, then plug into outlet and then put shaver in SmartClean System. Be certain plug is inserted firmly into shaver/SmartClean System, up to mark indicated on plug. To disconnect, turn SmartClean System off, remove charging plug from outlet.
9. Never put the shaver/SmartClean System in direct sunlight or store at a temperature above 140°F (60°C).
10. Keep the cord dry at all times. Do not handle with wet hands.
11. To prevent possible damage to the cord, do not wrap cord
around the shaver/SmartClean System.
12. Only use the power plug and other accessories supplied with
the appliance.
SAVE THESE INSTRUCTIONS
IMPORTANT: The power plug contains a transformer. Do not
cut off the power plug to replace it with another plug, as this will cause a hazardous condition.
ENGLISH
5
IMPORTANT SAFETY INSTRUCTIONS
When using an electric appliance, basic precautions should always be followed, including the following:
Read all instructions before using this appliance.
DANGER
To reduce the risk of electric shock:
1. Do not reach for a corded shaver/SmartClean System that has fallen into water. Unplug immediately.
2. Power plug and the accessories connected to it are not for immersion or for use in shower.
3. Do not use an extension cord with this appliance.
4. Do not place or store a SmartClean System where it can fall or be pulled into a tub or sink. Do not place or drop a SmartClean System into water or other liquid.
5. Always unplug this shaver/SmartClean System from the electrical outlet immediately after use, except when shaver/ SmartClean System is (re)charging.
6. Unplug and remove power supply cord from shaver
before cleaning.
7. The batteries used in this device may present a fire or chemical
burn hazard if mistreated. Do not disassemble, heat above 100ºC (212°F) or incinerate.
WARNING
To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Close supervision is necessary when this shaver/SmartClean System is used by, on, or near children or invalids.
2. Use this shaver/SmartClean System for its intended household use as described in this manual. Do not use attachments or a cleaning cartridge not recommended by Philips Electronics
ENGLISH
4
7
Table of Contents
Features ...................................................... 8-11
LED Display .............................................12-14
Charge Meter ...............................................14
Before First Use .....................................14-15
Charging ...................................................15-17
Recharging .....................................................17
Quick Charge ...............................................17
Put It To The Test & Shaving Tips ..............18
How to Shave
With An Electric Shaver .......................18-20
Using the SmartClick Trimmer ........... 21-22
Using the SmartClick Styler ................ 22-25
Travel Lock ..............................................25-26
Cleaning ....................................................26-36
Replacing the Shaving Heads ...............36-39
Maintenance .................................................. 40
Storage ............................................................40
Assistance ......................................................41
Battery Recycling ......................................... 41
Accessories ...................................................42
Warranty ........................................................ 43
ENGLISH
6
ENGLISH
45 - DAY MONEY-BACK GUARANTEE
To enjoy the closest and most comfortable shave from your new Philips Norelco Men’s Shaver, the shaver should be used exclusively for 3 weeks. This allows your hair and skin enough time to adapt to the Philips Norelco Shaving System. If, after that period of time, you are not fully satisfied with your Philips Norelco Men’s Shaver, send the product back along with dated sales receipt and we’ll refund you the full purchase price. The shaver must be shipped prepaid by insured
mail, insurance prepaid, have the original sales receipt, indicating pur­chase price, the date of purchase, and the money-back guarantee return authorization form enclosed. We cannot be responsible for lost mail.
The shaver must be postmarked no later than 45 days from the date of purchase. Philips Norelco reserves the right to verify the purchase price of the shaver and limit refunds not to exceed suggested retail price.
To obtain money-back guarantee return authorization form, call 1-800-243-3050 for assistance. Delivery of refund check will occur 6–8 weeks AFTER receipt of returned product.
98
SmartClick Precision
Trimmer or Styler*
Automatic Worldwide
Voltage 100V to 240V AC
Travel Case
Rechargeable 1-hour full
charge for up to 50 min.
of cordless shaving time
Quick Charge - For
one shave
Cordless - To shave
without a cord
Full 2-Year Warranty
45-Day Money-Back
Guarantee
ENGLISHENGLISH
Features
DynamicFlex Technology
Shaving Unit
• Hair Chamber
captures shaven hair
Comfort Rings
Electronic On/Off Button
Cleaning Indicator
Replacement Shaving Heads Indicator
Travel Lock
'Unplug for use' Indicator
3-Level Battery Display
• Shows remaining power level of battery
• Battery Charge,
Full & Low Indicators
*Depending on which shaver you purchased.
ENGLISH
11
Features
SmartClean System
SmartClean System Cap
Shaver Holder
On/Off
Button
Charging Indicator
Ready
Indicator
Cleaning
Cartridge
Replacement
Indicator
Cleaning
Indicator
Cleaning
Cartridge
Release Button
Cleaning Cartridge
10
1312
ENGLISH
Low Battery Indicator
C
- When the batter y is almost empty (5 or less shaving minutes left), the bottom charging light blinks orange.
C
'Unplug For Use' Indicator
The 'unplug for use' symbol will blink to remind you the shaver is connected to the outlet.
C
Replacement Shaving Heads Indicator
Every year, depending on your shaving behavior, the replacement shaving heads indicator lights up white continuously. See 'Replacing the Shaving Heads' section for instructions to reset the shaver. This reminds you that with new shaving heads you will guarantee yourself optimal shaving performance.
C
Cleaning Indicator
For optimal shaving performance, we recommend cleaning the shaver after EACH use. The blinking faucet will remind you the shaving unit needs to be cleaned. This happens after each shave.
ENGLISH
LED Display
Remove any sticker or protective foil from
the display before using shaver.
The display provides the following
information:
◗ Charging Indicator
C
- When the shaver is charging, the bottom charging light blinks and then lights up continuously. As charging continues, each charging light will blink and then light up continuously until the shaver is fully charged.
-Quick charge:When the shaver contains enough energy for one shave, the bottom charging light blinks slowly.
◗ Full Charge Indicator
C
- When the batter y has been fully charged,
all charging lights light up continuously.
After approximately 30 minutes the display automatically switches off again.
- If the on/off button is pressed during or after
charging, the 'unplug for use' symbol will blink
indicating the shaver is still connected to the outlet.
Remaining Battery Capacity
- The remaining batter y capacity is indicated by
the number of charging lights that are on.
1514
ENGLISH
Important
◗ Only use the power cord or SmartClean
System provided to charge the shaver.
◗ The power plug transforms 100-240V AC to
less than 24V DC.
Charging
Charging, recharging or storing at
temperatures below 40ºF or higher than 95ºF adversely affects lifetime of batteries. Charging or recharging requires one full hour. ◗ A fully charged shaver has a shaving time of up
to 50 minutes. You may recharge when the display indicates
the battery is almost empty. ◗ This shaver will not operate corded directly
from the electrical outlet. ◗ Do not charge the shaver in a pouch or travel
case.
C
1 Connect cord directly to shaver (1) and
connect the power plug into any 100V to 240V AC outlet (2). Use only the power cord provided.
An adaptor plug may be necessary for power
cord usage in some foreign countries. Use
an attachment plug adaptor of the proper
configuration for the power outlet.
1
2
ENGLISH
C
Travel Lock
The shaver is equipped with a travel lock function. You can use the travel lock function when you are going to store the shaver for a longer period or if you are going to take the shaver with you when traveling. See ‘Travel Lock’ section for instructions on how to use this function.
Charge Meter
Charge Meter monitors amount of remaining
battery power available. Remaining battery capacity is based on the amount of power consumed shaving per minute and is
dependent upon your skin and beard type, whether you use pre-shave lotion, and how often the styler is used. Initially your shaver may need to go through 2
or 3 full charge/recharge cycles before
remaining battery capacity indicators begin to
display your accurate battery power left.
Before First Use
Charge the shaver before you start using it
(see ‘Charging’). Make sure the shaver is
switched off before you start charging it. Remove any sticker or protective foil from
the display before using shaver.
1716
ENGLISH
C
4 Place the shaver into the holder (1), push
shaver back (2) and press down the top cap to connect the shaver (click).
The shaver will only fit in the Smar tClean System in one direction.
5 The battery indicator lights up to indicate
the shaver is charging.
6 Charging requires one full hour. A fully
charged shaver has a cordless shaving time of up to 50 minutes.
C
7 Press the top cap down (1), pull the shaver
forward (2) and lift shaver from holder (3).
Recharging
1 Recharging requires one full hour.
Recharge when the display indicates the battery is almost empty.
Quick Charge
When batteries are empty, recharging the shaver for 5 minutes gives enough energy for one cordless shave.
3
1
2
ENGLISH
The power cord will automatically conver t to work on 100V to 240V AC systems.
2 The display on the shaver will indicate
shaver is charging.
3 Charging requires one full hour. A fully
charged shaver has a cordless shaving time of up to 50 minutes.
Charging Shaver with SmartClean System
1 Connect the small plug to the SmartClean
System. Connect the power plug into any 100V to 240V AC outlet. Use only the power cord provided.
C
2 Press the top cap down to open the
SmartClean System.
C
3 Hold the shaver head side down above the
shaver holder.
1
2
1918
ENGLISH
Shaving
For best results on skin comfort, pre-trim
your beard if you have not shaved for 3 days or longer.
C 1 Turn shaver ON by pressing the on/off
button once. Shave against the direction of beard growth using only circular movements.
The shaver display shows the remaining battery capacity.
2 Stretch your skin with your free hand so
blades can lift and cut whiskers. Gently press shaver to skin so the floating heads can follow the contours of your face. DO NOT press too hard. Too much pressure can pinch the skin into the combs.
3 Turn shaver OFF by pressing the on/off
button once.
The shaver display shows the remaining battery capacity.
4 Clean the shaver after each use (see
chapter ‘Cleaning’).
C 5 Place the shaver in the SmartClean System
to protect shaver heads.
Wet Shaving
You can also use the shaver on a wet face with shaving foam or gel.
ENGLISH
Put It To The Test & Shaving Tips
21 Day Trial and Conversion Process. It is a fact
that your skin and beard need time to adjust to
a new shaving system. Use your new shaver exclusively for 3 weeks to
fully enjoy the closeness of a Philips Norelco
shave. At first you may not get as close a shave as you
expect, or your face may even become slightly
irritated. This is normal since your beard and skin will need time to adjust. Invest 3 weeks and you’ll soon experience the full joy of your
new shaver. Stick with it! If you alternate shaving methods
during the adjustment period, it may make it
more difficult to adapt to the Philips Norelco
shaving system. If you are still not convinced after 21 days,
Philips Norelco will refund you the full
purchase price as long as the request is
received within 45 days of purchase.
How To Shave With An Electric
Shaver
C◗ This symbol on the shaver indicates that the
shaver can be used in the bath or shower. ◗ Make sure the SmartClean System does not
get wet or near water. ◗ Use this shaver for its intended household use
as described in this manual.
ENGLISH
Using the SmartClick Trimmer
To Groom Sideburns and Moustache
C
1 Pull the shaving unit straight off the shaver.
NOTE: Do not turn the shaving unit while you pull it off the shaver.
C
2 Insert the raised notch of the SmartClick
trimmer into the slot in the top of the shaver. Press the trimmer down to attach it to the shaver. You will hear a ‘click’.
3 Turn shaver ON.
C 4 Hold trimmer to exact hairline desired.
Move trimmer downward with gentle pressure.
5 Trim beard, moustache or sideburns using
the trimmer.
6 Turn shaver OFF when finished.
7 Thoroughly clean the trimmer (see
‘Cleaning’).
C 8 Pull the trimmer straight off the shaver.
NOTE: Do not turn or twist the trimmer while you pull it off the shaver.
21
ENGLISH
C 1 Apply some water to your skin.
C 2 Apply shaving foam or gel to your skin.
3 Rinse the shaving unit under the tap
to ensure that the shaving unit glides smoothly over your skin.
4 Press the on/off button once to switch on
the shaver.
C 5 Move the shaving heads in circular
movements over your skin.
NOTE: Rinse the shaver under the tap regularly to ensure that it continues to glide smoothly over your skin.
6 Dry your face and thoroughly clean
the shaver after each use (see chapter ‘Cleaning’).
NOTE: Make sure you rinse all foam or gel off the shaver.
C
7 Place the shaver in the SmartClean System
to protect heads.
20
ENGLISH
Always comb beard and/or moustache with a
fine comb before using the styler.
The hair length settings on the styler
correspond to the remaining hair length after trimming. There are 5 settings from 3/64 in. – 3/16 in. (1-5mm).
C 1 Slide the comb straight into the guiding
grooves on both sides of the SmartClick styler. You will hear a ‘click’.
C 2 Press the length selector and push to the
left or right to select the desired hair length setting.
To prevent accidentally trimming hairs too short,
start with the maximum setting of 3/16 in. (5mm).
3 Turn shaver ON.
The shaver display shows the remaining battery capacity.
C 4 Move the styler downward with gentle
pressure making sure the front of the comb is in full contact with the skin.
NOTE: If cut hairs accumulate in the comb, turn
the shaver off, remove comb and blow and/or shake hair out of the comb.
23
ENGLISH
C 9 Insert the raised notch of the shaving unit
into the slot in the top of the shaver. Press the shaving unit down to attach it to the shaver. You will hear a ‘click’.
C 10 Place the shaver in the SmartClean System
to protect the heads.
Using the SmartClick Styler
C
1 Pull the shaving unit straight off the shaver.
NOTE: Do not turn the shaving unit while you pull it off the shaver.
C
2 Insert the raised notch of the SmartClick
styler into the slot in the top of the shaver. Press the styler down to attach it to the shaver. You will hear a ‘click’.
Styling with Comb Attachment
Use the SmartClick styler with the comb
attached to trim your beard and moustache. To prevent trimming your beard and
moustache too short, make sure your hair is
dry.
22
2
1
ENGLISH
C 7 Insert the raised notch of the shaving unit
into the slot in the top of the shaver. Press the shaving unit down to attach it to the shaver. You will hear a ‘click’.
C 8 Place the shaver in the SmartClean System
to protect the heads.
Travel Lock
If you are going to store the shaver for a longer time period or if traveling, it is possible to lock the shaver. The travel lock prevents the shaver from being switched on by accident.
Activating the travel lock
C
1 Press the ON/OFF button for 3 seconds.
 ◗ The travel lock symbol lights up white
continuously and the lock symbol blinks.
2 The travel lock has now been activated.
25
ENGLISH
Styling without Comb Attachment
Use the SmartClick styler without the comb
to contour your beard, moustache, sideburns
or neckline.
C 1 Pull the comb off the SmartClick styler.
Make sure to grab the comb in the center. Do not pull at the sides of the comb.
2 Turn shaver ON.
C 3 Contour your beard, moustache,
sideburns or neckline by moving the styler downward with gentle pressure.
Be careful, the styler cuts hairs very close to the skin, at a length of 1/32 in (0.5 mm).
4 Turn shaver OFF when finished.
The shaver display shows the remaining battery capacity.
C 5 Pull the SmartClick styler straight off the
shaver.
NOTE: Do not turn or twist the styler while you pull it off the shaver.
6 Thoroughly clean the styler and comb (see
‘Cleaning’).
24
3 sec.
Loading...
+ 30 hidden pages