Page 1
Quick Use Guide MC W770
This Quick Use Guide gives a rough
overview and helps to start quickly with
basic steps. Please read the supplied
instruction manual for detailed
information.
1 Insert batteries
Supplied accessories
– PC link software installer CD-ROM
– Wireless USB adapter and extension cable
– Remote control and 2 batteries, size AA
–2 loudspeaker boxes including
2 speaker cables
– AM/MW loop antenna
– FM wire antenna
– AC power cord
Open the battery compartment of the remote control and insert
2 alkaline batteries, type AA (R06, UM-3).
2 Connect speakers, antennas, an additional appliance (optional)
and the AC power cord
English
1 Connect the speaker cables to the MC W770.
Use the supplied speakers only. Using other speakers
can damage the set or the sound quality will be
negatively affected.
2 Connect the AM/MW antenna.
3 Connect the FM antenna.
4 If you want to connect an additional appliance, use a cinch
cable to connect the audio inputs of the MC W770 to the
audio outputs of the additional appliance.
5 Check whether the mains voltage as shown on
the type plate corresponds to your local mains
voltage. If it does not, consult your dealer or
service organisation.
Make sure all connections have been made
before switching on the mains supply.
Connect the AC power cord supplied to
AC MAINS ~ and to the wall socket.
1
Page 2
3 Install the tuner
VOL
AUX PC LINKTUNERCD
CD2
CD
3
CD5
CD4
CD1
ALBUM
BROWSE
VOL
1 When the AC power cord is connected for the first time
to the wall socket, TUNER and AUTO INSTALL - PRESS
PLAY are displayed.
4 Play your discs on the set
For playback on this set you can use:
– All pre-recorded audio CDs
– All finalised audio CDR and CDRW discs
– MP3-CDs (CD-ROMs with MP3 tracks)
2 Press ÉÅ on the set to store all available radio stations
automatically.
➜ Automatic searching and storing starts. Once completed,
the last tuned radio station will be played.
1 Press OPEN/CLOSE / on the set.
2 Press one of the disc keys (DISC 1,
DISC 2, DISC 3, DISC 4, or DISC 5)
on the set to select the desired disc
tray to be opened.
AUX PC LINKTUNERCD
CD
1
CD2
CD4
CD5
5 If you want to play one
particular disc:
Press one of the disc keys CD 1,
2
CD 2, CD 3, CD 4, or CD 5 on the
remote control to start playback of
the desired disc in the selected tray.
CD
3 Load a disc with the printed side up. 4 Press OPEN/CLOSE / again on the
set to close the tray.
3
SHUFFLEPROGRAMREPEAT DISPLAY
TIMERCLOCKSLEEP TIMER ON/OFF
00
If you want to play all loaded
discs:
Press CD on the remote control.
Then press ÉÅ to start playback.
To stop playback press STOP Ç.
Page 3
5 Install the wireless connection to your PC
AUX PC LINKTUNERCD
CD2
CD
3
CD5
CD4
CD
1
VOL
AUX PC LINKTUNERCD
CD2
CD
3
CD5
CD4
CD
1
VOL
VOL
+
PC system requirements:
– Windows 98SE/ME/2000/XP
–Pentium Class 350MHz processor or higher
– CD-ROM drive
– USB port
– Free hard disk space: 100 MB for the software
– 128MB RAM or higher
Do not connect the wireless USB adapter immediately! You will be asked during
the installation process to connect it.
If you have a Firewall installed on your PC, please switch it off during the
installation.
Please close all internet connections and other programs running on your PC
before starting installation.
1 Place the set as close as possible to the PC.
2 Switch on your PC and insert the installation disc.
Note: Do not use the icon, which will appear on the PC screen during the
computer
installation process.
3 The installation guide will appear automatically. If it does not, go to the CD-ROM
drive in Windows Explorer and double click on the SETUP_.exe.Then continue
as follows:
– Select your desired language from the list.
– Select Installing Software and then select Quick Installation and click
Install.
– Then follow the installation steps prompted by the screen to install the wireless
USB adapter driver, the Philips Media Manager software and the network setup.
Note: Windows may display a warning that the driver is not approved by
Microsoft (message differs with Windows version). Ignore the message and
continue with the installation.
4 Switch on the set and press PC LINK A.
5 During the network setup you will be asked to go to the install mode: Press and
hold PC LINK A for 5 seconds.
➜PC LINK is displayed and INSTALLING is scrolled.The set searches for a
connection to the PC.
When the installation has been finished successfully:
supplied wireless
USB adapter
➜PC LINK and COMPLETED are displayed.
6 Play your music collection from the PC via the set
1 Add your MP3 music folders and files to the Philips Media Manager, during or after
installation of Philips Media Manager. Only those folders and files you can see in the
Philips Media Manager will be accessible from the MC W770.
2 Make sure your PC is switched on.
3 Press PC LINK A to select the PC as source.
4 As soon as the connection is established:
ALBUM
BROWSE
➜ PC LINK is displayed and a track name is scrolled.
5 Press ÉÅ to start playback.
➜ PC LINK is displayed and the track name is scrolled.
➜ PC LINK and the elapsed playing time are displayed.
3
Page 4
7 Setting the clock
CD5
CD4
ALBUM
BROWSE
VOL
TIMER
DSC VEC
TIMER ON/OFF
AUX PC LINKTUNERCD
CD2
CD
3
CD5
CD4
CD
1
VOL
SHUFFLEPROGRAMREPEAT DISPLAY
TIMERCLOCKSLEEP TIMER ON/OFF
ALBUM
BROWSE
PROGRAMREPEAT
CLOCKSLEEP
1 Press and hold CLOCK on the
remote control for more than
2 seconds.
➜ SET CLOCK is displayed, the
hours and minutes digits start
blinking.
8 Timer setting
2 Press ALBUM 5 or ALBUM ∞ on
the remote control repeatedly to set
the hour.
3 Press 4 or ¢ on the remote
control repeatedly to set the
minutes.
PROGRAMREPEAT
CLOCKSLEEP
4 Press CLOCK on the remote control
to confirm the setting.
➜ The clock shows the set time.
1 Press and hold TIMER on the remote
control for more than 2 seconds.
➜ X starts blinking, SET TIMER is
displayed and the hours and
minutes digits start blinking.
2 Press CD,TUNER or PC LINK A on
the remote control to select the
source you want to be woken up
with.
3 Press ALBUM 5 or ALBUM ∞ on
the remote control repeatedly to set
the hour.
4 Press 4 or ¢ on the remote
control repeatedly to set the
minutes.
5 Press TIMER on the remote control
to confirm the setting.
9 Demonstration mode
● To activate the demonstration
mode press and hold
STOP DEMO Ç for 5 seconds
during standby or Eco Power standby
on the set until DEMO ON is displayed.
H
4 3103 305 2021.2 PDCC-LC/JW-0435
● To deactivate the
demonstration mode press and
hold STOP DEMO Ç again on the
set for 5 seconds until DEMO OFF is
displayed.
Loading...