Philips HX6950 User Manual

FlexCare

900+ series

Rechargeable

sonic toothbrush

4235.020.3356.1.indd 14235.020.3356.1.indd 1 06-04-09 09:3206-04-09 09:32

4235.020.3356.1.indd 24235.020.3356.1.indd 2 06-04-09 09:3206-04-09 09:32

Sonicare 900+ series

ENGLISH 4 ESPAÑOL 16 FRANÇAIS (CANADA) 28

4235.020.3356.1.indd 34235.020.3356.1.indd 3 06-04-09 09:3206-04-09 09:32

Introduction

Congratulations on your purchase and welcome to Philips! To fully beneﬁ t from the suppor

t that Philips offers, register your product at www.philips.

com/welcome.

IMPORTANT SAFEGUARDS

READ ALL INSTRUCTIONS BEFORE USE

DANGERS

To reduce the risk of electrocution: 1 Do not place or store product where it can fall or be pulled into a tub

or sink. 2 Do not place in or drop into water or other liquid. 3 Do not reach for a product that has fallen into water. Unplug

immediately. 4 Do not use while bathing.

WARNINGS

To reduce the risk of burns, electrocution, ﬁ re or injury to persons: 1 Discontinue use if this product appears damaged in any way (brush

head, handle, charger). This product contains no user-serviceable parts.

Refer to chapter ‘Guarantee and service’ if your Sonicare no longer

works properly or needs repair. 2 Never use the charger if it has a damaged cord or plug. 3 Keep cord away from heated surfaces. 4 Do not use the charger outdoors. 5 Do not use the charger if dropped into water. 6 This product is designed to clean your teeth, gums and tongue only.

Use this product only for its intended use as described in this booklet.

Discontinue use of this product and contact a physician/dentist if

discomfort or pain is experienced. 7 This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for

their safety. 8 Children should be supervised to ensure that they do not play with the

appliance. 9 Do not use attachments other than those recommended by the

manufacturer. 10 If your toothpaste contains peroxide, baking soda or other bicarbonate

(common in whitening toothpastes), thoroughly clean the brush head

and the handle with soap and water after each use. Otherwise the

plastic may crack. 11 To avoid damage to the product, do not place the brush head, handle,

charger or charger cover in the dishwasher for cleaning.

ENGLISH4

4235.020.3356.1.indd 44235.020.3356.1.indd 4 06-04-09 09:3206-04-09 09:32

12 Discontinue use of the sanitizer if the UV light bulb remains on when

the door is open. UV light can be harmful to the human eye and skin.

Keep the sanitizer out of the reach of children at all times. 13 Do not operate the UV sanitizer without the protective screen in place

to avoid contact with hot bulb. 14 If the sanitizer is used for 3 consecutive UV clean cycles (i.e., 3 times in

a row) a minimum of 30 minutes ‘Off Time’ is required before you start

another UV clean cycle. 15 The UV light bulb is hot during and immediately after the sanitizing

cycle. Do not touch the UV light bulb when it is hot. 16 Do not operate the UV sanitizer where aerosol (spray) products are

being used or where oxygen is being administered.

MEDICAL WARNINGS

1 Consult your dental professional before you use this product if you

have had oral or gum surgery in the previous 2 months. 2 Contact your dental professional if excessive bleeding occurs after

using this product or bleeding continues to occur after 1 week of use. 3 If you have a pacemaker or other implanted device, contact your

physician or the device manufacturer prior to use. 4 Sonicare has been tested and is compliant with safety standards for

electromagnetic devices. 5 Consult your physician prior to using the Sonicare if you have medical

concerns.

SAVE THESE INSTRUCTIONS

Your Sonicare (Fig. 1)

Hygienic travel cap

B Brush head C Interchangeable color code ring D Handle with soft grip E Power on/off button F Mode button G Brushing modes H Deluxe recharge gauge I UV sanitizer base with integrated charger and cord wrap (select

models)

J UV sanitizer (select models) K Deluxe charger (select models) L Charger cover with brush head holder M Travel charger N Charger base with cord wrap

- Not shown: UV light bulb

- Not shown: Sanitizer drip tray

- Not shown: Protective screen for UV light bulb

Note:

The contents of the box vary based on model purchased

ENGLISH 5

4235.020.3356.1.indd 54235.020.3356.1.indd 5 06-04-09 09:3206-04-09 09:32

Getting started

Changing the color code ring

Sonicare br

ush heads come with interchangeable color code rings to identify your brush head. To change the color code ring:

1 Pull the color code ring from the bottom of the brush head.

2 Install a new ring by slipping one edge of the new ring over the

bottom of the brush head.

Attaching the brush head

1 Align the brush head so the bristles face the front of the handle. 2 Firmly press the brush head down on the metal shaft until it stops.

Note:

There is a small gap between the color code ring and the handle.

Charging your Sonicare

1 Put the plug of the charger in a live electrical outlet. 2 Place the handle on the charger.

, The ﬂ

ashing light of the battery gauge indicates that the toothbrush

is charging.

- 1 solid green LED indicates that the toothbrush is 34-66% charged.

- 2 solid green LEDs indicate that the toothbrush is 67-94% charged.

- 3 solid green LEDs indicate that the toothbrush is fully charged.

Note:

If the battery charge of your Sonicare is low, you hear 3 beeps and 1 LED of the recharge gauge ﬂ ashes yellow for 30 seconds after completing the brushing cycle.

ENGLISH6

4235.020.3356.1.indd 64235.020.3356.1.indd 6 06-04-09 09:3206-04-09 09:32

Note: To keep the battery fully charged at all times, you may keep your Sonicare on the charger when not in use. Once the Sonicare is fully charged, the charger draws minimal energy from the electrical outlet.

Note: It takes at least 24 hours to fully charge the battery.

Using your Sonicare

Brushing instructions

1 Wet the bristles and apply a small amount of toothpaste. 2 Place the toothbrush bristles against the teeth at a slight angle

wards the gumline.

3 Press the power on/off button to switch on the Sonicare. 4 Apply light pressure to maximize Sonicare’s effectiveness and let the

Sonicar

e toothbrush do the brushing for you. Do not scrub.

5 Gently move the brush head slowly across the teeth in a small back

and f

orth motion so the longer bristles reach between your teeth.

Continue this motion throughout your brushing cycle.

Note: To make sure you brush evenly throughout the mouth, divide your mouth into 4 sections using the Quadpacer feature (see chapter ‘Features’).

6 Begin brushing in section 1 (outside top teeth) and brush for 30

seconds bef

ore moving to section 2 (inside top teeth). Continue brushing in section 3 (outside bottom teeth) and brush for 30 seconds before moving to section 4 (inside bottom teeth).

7 After you have completed the brushing cycle, you can

spend ad

ditional time brushing the chewing surfaces of your teeth and areas where staining occurs. You may also brush your tongue, with the toothbrush turned on or off, as you prefer.

Your Sonicare is safe to use on:

- Braces (brush heads wear out sooner when used on braces)

- Dental restorations (ﬁ

llings, crowns, veneers)

Brushing modes

Sonicare automatically starts in the default Clean mode.

1 Prior to turning on the Sonicare, press the mode button to toggle

betw

een modes. , The selected brushing mode illuminates. , Once a brushing mode has been selected, it remains active until

another brushing mode is selected.

Note: When the toothbrush is switched on, you cannot toggle between modes.

The following brushing modes are available:

Clean

Complete whole mouth cleaning (2 minutes).

ENGLISH 7

4235.020.3356.1.indd 74235.020.3356.1.indd 7 06-04-09 09:3206-04-09 09:32

Gum Care

Complete whole mouth cleaning (2 minutes) plus gentle cleaning for problem areas and along the gumline (1 minute).

Refresh

Touch-up for a quick clean (1 minute).

Sensitive

Gentle cleaning for sensitive gums and teeth (2 minutes).

Massage

Gentle gum stimulation (2 minutes).

Note: When the Sonicare is used in clinical studies, the default 2-minute Clean mode must be selected. The handle has to be fully charged. Deactivate the Easy-start feature. For areas where excess staining occurs, an additional 30 seconds of brushing time can be spent to help remove stains.

Features

Easy-start

- This Sonicare model comes with the Easy-start feature activated.

- The Easy-start feature gently increases power over the ﬁ r

st 14

brushings to ease into the Sonicare experience.

Note: Each of the ﬁ rst 14 brushings must be at least 1 minute in length to properly move through the Easy-start ramp-up cycle.

Deactivating or activating the Easy-start feature

1 Attach your brush head to the handle. 2 Place the handle on the plugged-in charger.

- To deactivate Easy-start:

Press and hold the po

wer on/off button for 2 seconds. You hear 1 beep to

indicate that the Easy-start feature has been deactivated.

- To activate Easy-start:

Press and hold the po

wer on/off button for 2 seconds. You hear 2 beeps to

indicate that the Easy-start feature has been activated.

Note: Using the Easy-start feature beyond the initial ramp-up period is not recommended and reduces Sonicare’s effectiveness in removing plaque.

Smartimer

The Smar timer indicates that your brushing cycle is complete when it automatically turns off the toothbrush at the end of the brushing cycle. Dental professionals recommend brushing at least 2 minutes twice a day.

ENGLISH8

4235.020.3356.1.indd 84235.020.3356.1.indd 8 06-04-09 09:3206-04-09 09:32

Quadpacer

- The Quadpacer is an inter

val timer that has a short beep and pause to remind you to brush the 4 sections of your mouth. Depending on the brushing mode you have selected, the Quadpacer beeps at different intervals during the brushing cycle. See sections ‘Brushing instructions’ and ‘Brushing modes’ in chapter ‘Using your Sonicare’.

The Quadpacer feature on this model has been activated. To deactivate or reactivate the Quadpacer feature:

1 Place the handle with a brush head attached on the plugged-in

charger

2 Press and hold the mode button for 2 seconds.

, Y

ou hear 1 beep to indicate the Quadpacer has been deactivated or

you hear 2 beeps to indicate the Quadpacer has been activated.

Cord wrap on deluxe charger (select models)

If your model includes the deluxe charger cover and base, the travel charger is pre-installed inside the cover. If you want to shorten the power cord, you can store excess cord in the cord wrap feature built into the charger base.

1 To separate the charger cover from the charger base, press the two

gra

y snap bars on the charger base and pull the white charger cover

upwards.

2 Wrap excess power cord around the gray charger base as shown in

the pictur

e. Be sure to wrap the cord on the inside of the two snap

levers.

3 When you have stored the excess cord, guide the power cord

thr

ough the small groove in the rear of the gray charger base.

4 To reattach the charger cover, press it down over the charger base

until it snaps into place.

Tip: For extra convenience during travel, you can remove the travel charger and use it without the charger cover and charger base.

ENGLISH 9

4235.020.3356.1.indd 94235.020.3356.1.indd 9 06-04-09 09:3206-04-09 09:32

Cord wrap on sanitizer with integrated charger (select models)

- If your model includes the sanitizer, you can store excess cord using the

cord wr

ap feature built into the bottom of the sanitizer.

Sanitizing (select models)

- With the UV sanitiz

er you can clean your brush head after every use.

Discontinue use of the sanitizer if the UV light bulb remains on when the door is open or if the blue window is broken or missing from the sanitizer. UV light can be harmful to the human eye and skin. This device should be kept out of reach of children at all times.

Unplug the sanitizer and call Consumer Care if the sanitizer gives off smoke or a burning smell while it is operating..

1 After brushing, rinse the brush head and shake off excess water.

Do not place the tra

vel cap on the brush head during sanitization.

2 Place your ﬁ

nger in the door recess on top of the sanitizer and pull

open the door.

3 Place the brush head on one of the 2 pegs in the sanitizer.

Note:

Only clean Sonicare ProResults brush heads in the sanitizer.

Make sure the bristles of the brush head directly face the light bulb.

4 Make sure the sanitizer is plugged into a live outlet of appropriate

oltage.

5 Close the door and press the green power on/off button once to

select the UV clean cycle.

Note: You can only turn on the sanitizer if the door is properly closed.

Note: The sanitizer stops if you open the door during the sanitizing cycle.

Note: The sanitizer cycle runs for 10 minutes and then automatically shuts off.

, The sanitizer is in operation when the blue light glows through the

window.

, When the sanitizing cycle is complete, the sanitizer automatically

shuts off.

ENGLISH10

4235.020.3356.1.indd 104235.020.3356.1.indd 10 06-04-09 09:3206-04-09 09:32

Cleaning

Do not clean the brush head, handle, travel charger, charger cover and the UV sanitizer in the dishwasher

Toothbrush handle

1 Remove the brush head and rinse the metal shaft area with warm

water

Do not push on the rubber seal on the metal shaft with sharp objects, as this may cause damage.

2 Use a damp cloth to wipe the entire surface of the handle.

Brush head

1 Rinse the brush head and bristles after each use. 2 Remove the brush head from the handle and rinse the brush head

connection at least once a w

eek with warm water.

Charger

1 Unplug the charger. 2 Use a damp cloth to wipe the surface of the charger.

Brush head UV Sanitiz

er (select models)

Do not clean the sanitizer when the UV light bulb is hot.

For optimal effectiveness, it is recommended to clean your sanitizer weekly.

1 Unplug the sanitizer. 2 Pull the drip tray straight out. Rinse the drip tray and wipe it clean

with a damp cloth.

3 Clean all reﬂ

ector surfaces with a damp cloth.

4 Remove the protective screen in front of the UV light bulb.

o remove the screen, grasp the edges next to the snaps, gently squeeze

and pull out the protective screen.

5 Remove the UV light bulb.

o remove the light bulb, grasp it and pull it out of the metal clasp.

ENGLISH 11

4235.020.3356.1.indd 114235.020.3356.1.indd 11 06-04-09 09:3206-04-09 09:32

6 Clean the protective screen and the UV light bulb with a damp cloth. 7 Reinsert the UV light bulb.

o reinsert the light bulb, align the bottom of the light bulb with the metal

clasp and push the bulb into the clasp.

8 Reinsert the protective screen.

o reinsert the screen, align the pegs on the screen with the slots on the reﬂ ective surface near the UV light bulb. Push the screen straight into the slots on the sanitizer.

Storage

- If you are not going to use the product for an extended period of

time

, unplug it from the electrical outlet, clean it and store it in a cool and dry place away from direct sunlight. You can use the cord wrap to store the power cord in an organized manner.

Replacement

Brush head

- Replace Sonicare brush heads every 3 months to achieve optimal

results.

- Use only compatible Sonicare replacement brush heads.

UV light bulb

- Replacement UV bulbs are available through your Sonicare Consumer

Care Center in Nor

th America by calling 1-800-682-7664. Outside

North America, contact your local Philips Consumer Care Center.

Disposal

- The rechar

geable battery inside your Sonicare cannot be replaced, but is easy to remove for recycling. At the end of product life and prior to disposal, please remove the rechargeable battery from the handle by following the instructions below.

- Do not throw away the appliance or the UV light bulb (bulb contains

mercur

y) with the normal household waste at the end of its life, but hand it in at an ofﬁ cial collection point for recycling. By doing this, you help to preserve the environment.

- If you have any recycling questions, contact your local waste

management ofﬁ ce

ENGLISH12

4235.020.3356.1.indd 124235.020.3356.1.indd 12 06-04-09 09:3206-04-09 09:32

Removing the rechargeable battery

Please note that this process is not reversible.

To remove the rechargeable battery, you need a ﬂ at-head (standard) screwdriver. Observe basic safety precautions when you follow the procedure outlined below. Be sure to protect your eyes, hands, ﬁ ngers, and the surface on which you work.

1 To deplete the rechargeable battery of any charge, remove the

handle fr

om the charger, turn on the Sonicare and let it run until it stops. Repeat this step until you can no longer switch on the Sonicare.

2 Insert a screwdriver into the slot located at the bottom of the

handle and turn counter

clockwise to release the bottom cap.

3 Hold the handle upside down and push down on the shaft to release

the internal components of the handle

4 Insert the screwdriver under the circuit board, next to the battery

connections,

and twist to break the connections. Remove the circuit

board and pry the battery from the plastic carrier.

The rechargeable battery can now be recycled and the rest of the product discarded appropriately.

Guarantee and service

Philips guarantees its products for two years after the date of purchase. Defects due to faulty materials and workmanship will be repaired or replaced at Philips expense provided that convincing proof of purchase in the qualifying period is provided. Contact our Consumer Care Center at 1-800-682-7664 (Nor th America), outside North America contact your local Philips Consumer Care Center. Internet information: www.sonicare.com (North America) or www.philips. com (outside North America).

ENGLISH 13

4235.020.3356.1.indd 134235.020.3356.1.indd 13 06-04-09 09:3206-04-09 09:32

WARRANTY EXCLUSIONS

What is not covered under warranty:

- Brush heads

- Damage caused by misuse, abuse, neglect, alterations or unauthorized

repair

- Normal wear and tear, including chips, scratches, abrasions,

discolor

ation or fading.

- UV light bulb

IMPLIED W

ARRANTIES

ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE DURATION OF THE EXPRESS WARRANTIES SET FORTH ABOVE. IN SOME STATES LIMITATIONS ON DURATION OF IMPLIED WARRANTIES DO NOT APPLY.

LIMITATION OF REMEDIES

IN NO EVENT SHALL PHILIPS OR ANY OF ITS AFFILIATED OR SUBSIDIARY COMPANIES BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES BASED UPON BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, TORT, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, WITHOUT LIMITATION, LOSS OF SAVINGS OR REVENUE; LOSS OF PROFIT; LOSS OF USE; THE CLAIMS OF THIRD PARTIES INCLUDING, WITHOUT LIMITATION, DENTISTS AND DENTAL HYGIENISTS; AND COST OF ANY SUBSTITUTE EQUIPMENT OR SERVICES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES.

ENGLISH14

4235.020.3356.1.indd 144235.020.3356.1.indd 14 06-04-09 09:3206-04-09 09:32

+ 30 hidden pages