HTL1510B
User manual
Contents
1 Important 2
Help and support 2
Safety 2
Care for your product 3
Care of the environment 3
Compliance 4
2 Your SoundBar 4
Main unit 4
Remote control 5
Connectors 6
3 Connect 6
Placement 6
Connect the SoundBar and the
Subwoofer
Connect audio from TV and other
devices
4 Use your SoundBar 9
Adjust the volume 9
MP3 player 9
Play audio through Bluetooth 10
Auto standby 10
Apply factory settings 10
Update software 10
7
8
5 Wall mount 11
6 Product specifications 11
7 Troubleshooting 12
1EN
1 Important
Read and understand all instructions before you
use your product. If damage is caused by failure
to follow instructions, the warranty does not
apply.
Help and support
• Never place the product and accessories
including direct sunlight.
• Never insert objects into the ventilation
slots or other openings on the product.
• Where the mains plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
• Batteries (battery pack or batteries
installed) shall not be exposed to excessive
For extensive online support, visit
www.philips.com/support to:
• download the user manual and the quick
start guide
• watch video tutorials (available only for
selected models)
•
questions (FAQs)
• email us a question
• chat with our support representative.
Follow the instructions on the website to select
your language, and then enter your product
model number.
Alternatively, you can contact Consumer Care
in your country. Before you contact, note down
the model number and serial number of your
back or bottom of your product.
Safety
Risk of electric shock or
• Before you make or change any
connections, make sure that all devices are
disconnected from the power outlet.
• Never expose the product and accessories
to rain or water. Never place liquid
containers, such as vases, near the product.
If liquids are spilt on or into the product,
disconnect it from the power outlet
immediately. Contact Consumer Care to
have the product checked before use.
• Disconnect the product from the power
outlet before lightning storms.
• When you disconnect the power cord,
always pull the plug, never the cable.
Risk of short circuit or
•
the type plate at the back or bottom of
the product.
• Before you connect the product to the
power outlet, ensure that the power
voltage matches the value printed on the
back or bottom of the product. Never
connect the product to the power outlet if
the voltage is different.
Risk of injury or damage to this product!
• For wall mounting, this product must be
securely attached to the wall in accordance
with the installation instructions. Use
only the supplied wall mount bracket (if
available). Improper wall mounting may
result in accident, injury or damage. If you
have any query, contact Consumer Care in
your country.
• Never place the product or any objects
on power cords or on other electrical
equipment.
• If the product is transported in
temperatures below 5 °C, unpack the
product and wait until its temperature
matches room temperature before
connecting it to the power outlet.
• Parts of this product can be made of
glass. Handle with care to avoid injury and
damage.
2 EN
Risk of overheating!
•
space. Always leave a space of at least four
inches around the product for ventilation.
Ensure curtains or other objects never
cover the ventilation slots on the product.
Risk of contamination!
• Do not mix batteries (old and new or
carbon and alkaine, etc.).
• CAUTION: Danger of explosion if batteries
are incorrectly replaced. Replace only with
the
same or equivalent type.
• Remove batteries if they are exhausted or
if the remote control is not to be used for
a long time.
• Batteries contain chemical substances, they
should be disposed of properly.
Risk of swallowing batteries!
• The product/remote control may contain
a coin/button type battery, which can be
swallowed. Keep the battery out of reach
of children at all times! If swallowed, the
battery can cause serious injury or death.
Severe internal burns can occur within two
hours of ingestion.
• If you suspect that a battery has been
swallowed or placed inside any part of the
body, seek immediate medical attention.
• When you change the batteries, always
keep all new and used batteries out of
reach of children. Ensure that the battery
compartment is completely secure after
you replace the battery.
• If the battery compartment cannot be
completely secured, discontinue use of the
product. Keep out of reach of children and
contact the manufacturer.
This is CLASS II apparatus with double
insulation, and no protective earth provided.
Care for your product
Care of the environment
Disposal of your old product and battery
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
This symbol on a product means that the
product is covered by European Directive
2012/19/EU.
This symbol means that the product contains
batteries covered by European Directive
2013/56/EU which cannot be disposed of with
normal household waste.
Inform yourself about the local separate
collection system for electrical and electronic
products and batteries. Follow local rules and
never dispose of the product and batteries
with normal household waste. Correct disposal
of old products and batteries helps prevent
negative consequences for the environment and
human health.
Removing the disposable batteries
To remove the disposable batteries, see battery
installation section.
3EN
Compliance
2 Your SoundBar
This product complies with the radio
interference requirements of the European
Community.
Hereby, MMD Hong Kong Holding Limited
declares that this product is in compliance
with the
essential requirements and other
relevant
provisions of Directive 2014/53/EU.
You can find the Declaration of Conformity on
www.p4c.philips.com.
Congratulations on your purchase, and
the support that Philips offers, register your
SoundBar at www.philips.com/welcome.
Main unit
This section includes an overview of the main
unit.
1
2
3
4
5
4 EN
1
Switch the soundbar on or to standby.
2
(SOURCE)
Select an input source for the soundbar.
3
Volume+/-
Increase or decrease volume.
4
Soundbar’s LED indicator
• Light up red when the soundbar is in
standby.
• Light up green when you switch to
line in input source (3.5mm stereo
audio cable).
• Light up blue when you switch to
Bluetoothmode and Bluetooth devices
are paired.
• Light up yellow when you switch to
optical input source.
• Blink red when you increase or decrease
volume, solid red when you maximize or
minimize volume.
Blink red at a low rate when you mute
•
the soundbar.
Subwoofer’s LED indicator
5
• Blink red before it is connected
with the SoundBar.
• Solid green when it is successfully
connected with the SoundBar.
Remote control
This section includes an overview of the
remote control.
1
1
(Standby-On)
Switch the SoundBar on or to standby.
2
LINE
Switch to LINE IN mode.
3
Switch to Bluetooth mode.
+/- (Volume)
4
• Increase or decrease volume.
Play buttons
5
: Play, pause or resume play in
•
Bluetooth mode (only for AVRCP
supported Bluetooth devices).
•
/ : Skip to the previous or next
track in Bluetooth mode (only for
AVRCP-supported
6
SOUND
Choose Music, Movie or News mode.
7
7
OPT
Switch your audio source to the optical
connection.
8
Bluetooth devices).
Mute or restore volume.
2
3
4
5
6
SOUND
OPT
7
8
5EN
Connectors
3 Connect
This section includes an overview of the
connectors available on your SoundBar and
Subwoofer.
1
2
3 4
5
1
SERVICE
For software upgrade.
2
LINE IN
Line input from, for example, an MP3 player
(3.5mm stereo).
3
OPTICAL
Connect to an optical audio output on the
TV or a digital device.
4
DC IN
Connect the soundbar to the power supply.
5
AC IN
Connect the Subwoofer to the power supply.
This section helps you connect your SoundBar
to a TV and other devices.
For information about the basic connections of
your SoundBar and accessories, see the quick
start guide.
Note
•
plate at the back or bottom of the product.
• Before you make or change any connections, make sure
that all devices are disconnected from the power outlet.
Placement
Place your SoundBar and Subwoofer as shown
below.
6 EN
Connect the SoundBar and
Subwoofer
1 Connect the SoundBar and Subwoofer
through Bluetooth.
• The Subwoofer will be connected with
the SoundBar via Bluetooth signal.
• The Subwoofer’s indicator will blink red
before connected with the SoundBar, and
will show solid blue after connected with
the SoundBar.
• First plug in and power on the SoundBar,
long press the “source” button for 5 seconds
until it begins automatic search, and then plug
in and power on the Subwoofer, its indicator
will show solid blue after blink red for 8 seconds,
which means successful pair with the SoundBar.
• If the SoundBar and the Subwoofer has been
paired before, when you again plug in and
power on the SoundBar, the Subwoofer will
be automatically be paired with the SoundBar
with normal sound output and solid blue
indicator. And the Subwoofer will be powered
off automatically after the SoundBar being
powered off.
7EN
Connect audio from TV and
other devices
Option 1: Connect audio through a
digital optical cable
Best quality audio
Option 2: Connect audio through
a 3.5mm stereo audio cable
Basic quality audio
1 Using a 3.5mm stereo audio cable, connect
the LINE IN connector on your SoundBar
to
the LINE
device.
connector on the TV or other
1 Using an optical cable, connect the
OPTICAL connector on your SoundBar to
the OPTICAL OUT connector on the TV
or other device.
• The digital optical connector might be
labeled SPDIF or SPDIF OUT.
8 EN
4 Use your
SoundBar
MP3 player
Connect your MP3 player to play your audio
This section helps you use the SoundBar to play
audio from connected devices.
Before you start
• Make the necessary connections
described in the Quick Start Guide
or download the User Manual from
www.philips.com/support.
• Switch the SoundBar to the correct source
for other devices.
Adjust the volume
1
Press +/- (Volume) to increase or decrease
a volume level.
• To mute sound, press
• To restore the sound, press
press +/- (Volume).
Volume indicator
• When you press the volume+ to increase
the volume, the SoundBar’s indicator will
blink red, and the volume will return to the
normal state after it reaches the maximum
with the SoundBar’s indicator showing solid
red for 2 seconds.
• When you press the volume- to decrease
the volume, the SoundBar’s indicator will
blink red, and the volume will return to the
normal state after it reaches the minimum
with the SoundBar’s indicator showing solid
red for 2 seconds.
.
again or
What you need
• An MP3 player.
• A 3.5mm stereo audio cable.
1 Using the 3.5mm stereo audio cable,
connect the MP3 player to the AUDIO IN
connector on your SoundBar.
2 Press AUDIO IN on the remote control.
3 Press the buttons on the MP3 player to
9EN
Play audio through Bluetooth
Through Bluetooth, connect the SoundBar with
your Bluetooth device (such as an iPad, iPhone,
iPod touch, Android phone, or laptop), and then
device through your SoundBar speakers.
What you need
• A Bluetooth device which supports
Bluetooth profile A2DP and AVRCP,
and with Bluetooth version as 5.0.
• The operational range between the
SoundBar and a Bluetooth device is
approximately 4 meters (13 feet).
1 Press on the remote control to switch
the SoundBar to Bluetooth mode.
The soundbar’s indicator blinks blue.
2 On the Bluetooth device, switch on
Bluetooth, search for and select Philips
HTL1510B to start connection (see the
user manual of the Bluetooth device on
how to enable Bluetooth).
During connection, the soundbar’s
indicator
blinks blue.
3 Wait until the soundbar’s indicator becomes
solid blue.
If the connection fails, the indicator
blinks continually at a lower rate.
4
your Bluetooth device.
• During play, if a call is coming, music
play is paused.
• If your Bluetooth device supports
Note
The music streaming may be interrupted by obstacles
•
between the device and SoundBar, such as wall, metallic
casing that covers the device, or other devices nearby
that operate in the same frequency.
• If you want to connect your SoundBar with another
Bluetooth device, press and hold
control to disconnect the currently connected
Bluetooth device.
on the remote
Auto standby
When playing media from a connected device,
this product automatically switches to standby
after 15 minutes of button inactivity and no
audio play from a connected device.
Apply factory settings
You can reset your SoundBar to the default
setting mode.
1 In LINE mode, long press the power key
of the remote control for 5 seconds.
.
The factory settings is restored.
Update software
To continually improve the product, software
upgrade may be offered. Visit ww.philips.com/
support to check if the latest software version
is available.
you can press
or press
/ to skip to a track,
to pause/resume play.
5 To exit Bluetooth, select other source.
• When your switch back to Bluetooth
mode, Bluetooth connection remains
active.
10 EN
5 Wall mount
Note
Improper wall mounting may result in accident, injury or
•
damage. If you have any query, contact Consumer Care
in your country.
• Before wall mounting, make sure the wall can support
the weight of your SoundBar.
Screw length/diameter
Depending on the type of wall mounting your
SoundBar, make sure that you use screws of a
suitable length and diameter.
See the illustration in the quick start guide on
how to wall mount the SoundBar.
1) Drill two holes on the wall.
2) Secure the dowels and screws in the holes.
3) Hang the SoundBar on the fastening screws.
6 Product
specifications
Note
•
notice.
• RMS total output power:
70W RMS (+/- 0.5 dB, 10% THD)
• Frequency response: 50 Hz-15 kHz / ±3 dB
• Signal-to-noise ratio:
> 65 dB (CCIR) / (A-weighted)
• Total Harmonic Distortion: <1%
• Input sensitivity:
• LINE IN: 450mV +/-50mV
Audio
• S/PDIF Digital audio input:
• Optical: TOSLINK
• Sampling frequency:
• MP3: 8 kHz, 11 kHz, 12 kHz, 16 kHz,
22 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz
• Constant bit rate:
• MP3: 8 kbps-320 kbps
Bluetooth
•
• Bluetooth version: 5.0
• Frequency band/Output power:
0
11EN
Main unit
Soundbar
• Power supply: 100-240 V~, 50/60 Hz
• Power consumption: 15V/1.6A
Standby power consumption: ≤0.5W
•
Dimensions (W x H x D):
•
960 x 67.8 x 85.5 mm
• Weight: XX kg
• Built-in speakers: 2 x full range
(52 mm/2”, 4 ohm)
Subwoofer
• Power supply: 100-240 V~, 50/60 Hz
• Power consumption: 20W
••Standby power consumption: ≤2W
Dimensions (W x H x D):
155 x 252 x 205 mm
• Weight: XX kg
• Built-in speakers: 1 x low frequency
(118 mm/4.5”, 6 ohm)
7 Troubleshooting
Warning
•
Risk of electric shock. Never remove the casing of the
product.
To keep the warranty valid, never try to repair
the product yourself.
If you have problems using this product, check
the following points before you request service.
If you still have a problem, get support at
www.philips.com/support.
Main unit
The buttons on the SoundBar do not work.
• Disconnect the SoundBar from the power
supply for a few minutes, then reconnect.
Remote control batteries
• 1 x AAA-R03-1.5 V
Standby information
• When the product remains inactive for
15 minutes, it automatically switches to
standby or networked standby.
• When the product (soundbar or subwoofer)
remains standby information, the power
consumption in standby is less than 2W.
• To deactivate Bluetooth connection, press
and hold the Bluetooth button on the
remote control.
• To activate Bluetooth connection, enable
Bluetooth connection on your Bluetooth
device.
Sound
No sound from SoundBar speakers.
• Connect the audio cable from your
SoundBar to your TV or other devices.
• Reset your SoundBar to its factory settings.
• On the remote control, select the correct
audio input.
• Make sure that the SoundBar is not muted.
Distorted sound or echo.
• If you play audio from the TV through the
SoundBar, make sure that the TV is muted.
Bluetooth
A device cannot connect with the SoundBar.
• The device does not support the
SoundBar.
• You have not enabled the Bluetooth
function of the device. See the user manual
of the device on how to enable the
function.
12 EN
• The device is not correctly connected.
Connect the device correctly. (see 'Play
audio through Bluetooth' on page 10)
• The SoundBar is already connected with
another Bluetooth device. Disconnect the
connected device, then try again.
Quality of audio play from a connected
Bluetooth device is poor.
• The Bluetooth reception is poor. Move the
device closer to the SoundBar, or remove
any obstacle between the device and the
SoundBar.
The connected Bluetooth device connects and
disconnects constantly.
• The Bluetooth reception is poor. Move the
device closer to the SoundBar, or remove
any obstacle between the device and the
SoundBar.
• Turn off Wi-Fi function on the Bluetooth
device to avoid interference.
• For some Bluetooth, the Bluetooth
connection can be deactivated
automatically to save power. This does not
indicate any malfunction of the SoundBar.
13EN
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.
Specifications are subject to change without notice.
Philips and Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V.
and are used under license. This product has been manufactured by and is sold under
the responsibility of MMD Hong Kong Holding Limited. or one of its affiliates, and
MMD Hong Kong Holding Limited. is the warrantor in relation to this product.
Loading...