Page 1
HTL1190BX
www.philips.com/support
User manual
Always there to help you
Register your product and get support at
Question?
Contact
Philips
Page 2
Page 3
1EN
Contents
1 Important 2
Help and support 2
Safety 2
Care for your product 3
Care of the environment 3
2 Your SoundBar 4
Main unit 4
Remote control 4
Connectors 5
3 Connect 6
Placement 6
Connect audio from TV and other devices 6
4 Use your SoundBar 7
Adjust the volume 7
Choose your sound 7
MP3 player 8
USB storage devices 9
Play audio through Bluetooth 9
Auto standby 10
Apply factory settings 10
Update software 10
5 Wall mount 10
6 Productspecications 11
7 Troubleshooting 12
Page 4
2 EN
1 Important
Read and understand all instructions before you
use your product. If damage is caused by failure
to follow instructions, the warranty does not
apply.
Help and support
For extensive online support, visit
www.philips.com/support to:
• download the user manual and the quick
start guide
• watch video tutorials (available only for
selected models)
• nd answers to frequently answered
questions (FAQs)
• email us a question
• chat with our support representative.
Follow the instructions on the website to select
your language, and then enter your product
model number.
Alternatively, you can contact Consumer Care
in your country. Before you contact, note down
the model number and serial number of your
product. You can nd this information on the
back or bottom of your product.
Safety
Riskofelectricshockorre!
• Before you make or change any
connections, make sure that all devices are
disconnected from the power outlet.
• Never expose the product and accessories
to rain or water. Never place liquid
containers, such as vases, near the product.
If liquids are spilt on or into the product,
disconnect it from the power outlet
immediately. Contact Consumer Care to
have the product checked before use.
• Never place the product and accessories
near naked ames or other heat sources,
including direct sunlight.
• Never insert objects into the ventilation
slots or other openings on the product.
• Where the mains plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
• Batteries (battery pack or batteries
installed) shall not be exposed to excessive
heat such as sunshine, re or the like.
• Disconnect the product from the power
outlet before lightning storms.
• When you disconnect the power cord,
always pull the plug, never the cable.
Riskofshortcircuitorre!
• For identication and supply ratings, see
the type plate at the back or bottom of
the product.
• Before you connect the product to the
power outlet, ensure that the power
voltage matches the value printed on the
back or bottom of the product. Never
connect the product to the power outlet if
the voltage is different.
Riskofinjuryordamagetothisproduct!
• For wall mounting, this product must be
securely attached to the wall in accordance
with the installation instructions. Use
only the supplied wall mount bracket (if
available). Improper wall mounting may
result in accident, injury or damage. If you
have any query, contact Consumer Care in
your country.
• Never place the product or any objects
on power cords or on other electrical
equipment.
• If the product is transported in
temperatures below 5°C, unpack the
product and wait until its temperature
matches room temperature before
connecting it to the power outlet.
• Parts of this product can be made of
glass. Handle with care to avoid injury and
damage.
Page 5
3EN
Riskofoverheating!
• Never install this product in a conned
space. Always leave a space of at least four
inches around the product for ventilation.
Ensure curtains or other objects never
cover the ventilation slots on the product.
Riskofcontamination!
• Do not mix batteries (old and new or
carbon and alkaine, etc.).
• Danger of explosion if batteries are
incorrectly replaced. Replace only with the
same or equivalent type.
• Remove batteries if they are exhausted or
if the remote control is not to be used for
a long time.
• Batteries contain chemical substances, they
should be disposed of properly.
Riskofswallowingbatteries!
• The product/remote control may contain
a coin/button type battery, which can be
swallowed. Keep the battery out of reach
of children at all times! If swallowed, the
battery can cause serious injury or death.
Severe internal burns can occur within two
hours of ingestion.
• If you suspect that a battery has been
swallowed or placed inside any part of the
body, seek immediate medical attention.
• When you change the batteries, always
keep all new and used batteries out of
reach of children. Ensure that the battery
compartment is completely secure after
you replace the battery.
• If the battery compartment cannot be
completely secured, discontinue use of the
product. Keep out of reach of children and
contact the manufacturer.
This is CLASS II apparatus with double
insulation, and no protective earth provided.
Care for your product
Use only microber cloth to clean the product.
Care of the environment
Disposal of your old product
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
Do not throw away the product with the
normal household waste at the end of its life,
but hand it in at an ofcial collection point or
recycling. By doing this, you help to preserve the
environment.
Page 6
4 EN
2 Your SoundBar
Congratulations on your purchase, and
welcome to Philips! To fully benet from
the support that Philips offers, register your
SoundBar at www.philips.com/welcome.
Main unit
This section includes an overview of the main
unit.
a
Switch the SoundBar on or to standby.
b SOURCE
Select an input source for the SoundBar.
c Volume+/-
Increase or decrease volume.
d LED indicators
• STANDBY: Lights up when the
SoundBar is in standby.
• COAXIAL: Lights up when you switch
to coaxial input source.
• OPTICAL: Lights up when you switch
to optical input source.
• AUX: Lights up when you switch to
analog input source.
ab c d
• AUDIO IN: Lights up when you switch
to audio input source (3.5mm jack).
• USB: Lights up you switch to USB
source.
•
Lights up when you switch to
Bluetooth mode and Bluetooth devices
are paired.
Blinks when you switch to Bluetooth
mode and Bluetooth devices are not
paired.
Remote control
This section includes an overview of the
remote control.
a (Standby-On)
Switch the SoundBar on or to standby.
b Source buttons
• COAX: Switch your audio source to
the coaxial connection.
a
b
b
b
c
d
f
e
g
h
i
j
Page 7
5EN
• OPT: Switch your audio source to the
optical connection.
• AUX: Switch your audio source to the
AUX connection.
• AUDIO IN: Switch your audio source
to the MP3 connection (3.5mm jack).
• : Switch to Bluetooth mode.
• USB: Switch your audio source to the
USB connection.
c +/- (Volume)
• Increase or decrease volume.
d
Mute or restore volume.
e BASS +/-
Increase or decrease bass.
f NIGHT
Turn night mode on or off.
g TREBLE +/-
Increase or decrease treble.
h SURR
Toggle between stereo and virtual
surround sound. Virtual surround is
applicable for the audio codecs, such as
MP3, PCM and MPEG (except Dolby
Digital).
i AUDIO SYNC +/-
Applicable to COAXIAL (COAX) and
OPTICAL (OPT) sources only. Increase or
decrease audio delay.
j Play buttons
• : Play, pause or resume play in USB
mode and Bluetooth mode (only for
AVRCP-supported Bluetooth devices).
• / : Skip to the previous or next
track in USB mode and Bluetooth
mode (only for AVRCP-supported
Bluetooth devices).
Connectors
This section includes an overview of the
connectors available on your SoundBar.
a DIGITAL IN-OPTICAL
Connect to an optical audio output on the
TV or a digital device.
b AUX
Connect to an analog audio output on the
TV or an analog device.
c COAXIAL
Connect to a coaxial audio output on the
TV or a digital device.
d
Audio input from a USB storage device.
e AUDIO IN
Audio input from, for example, an
MP3 player (3.5mm jack).
f AC MAINS~
Connect to the power supply.
b
a
c
d
f
e
Page 8
6 EN
3 Connect
This section helps you connect your SoundBar
to a TV and other devices.
For information about the basic connections of
your SoundBar and accessories, see the quick
start guide.
Note
• For identication and supply ratings, refer to the type
plate at the back or bottom of the product.
• Before you make or change any connections, make sure
that all devices are disconnected from the power outlet.
Placement
Place your Soundbar as shown below.
Connect audio from TV and
other devices
Play audio from TV or other devices through
your Soundbar.
Use the best quality connection available on
your TV and other devices.
Option 1: Connect audio through a
digital optical cable
Best quality audio
1 Using an optical cable, connect the
OPTICAL connector on your SoundBar to
the OPTICAL OUT connector on the TV
or other device.
• The digital optical connector might be
labeled SPDIF or SPDIF OUT.
Option 2: Connect audio through a
digital coaxial cable
Best quality audio
1 Using a coaxial cable, connect the
COAXIAL connector on your SoundBar
to the COAXIAL/DIGITAL OUT
connector on the TV or other device.
• The digital coaxial connector might be
labeled DIGITAL AUDIO OUT.
TV
Page 9
7EN
Option 3: Connect audio through
analog audio cables
Basic quality audio
1 Using an analog cable, connect the AUX
connectors on your SoundBar to the
AUDIO OUT connectors on the TV or
other device.
DVD
4 Use your
SoundBar
This section helps you use the SoundBar to play
audio from connected devices.
Before you start
• Make the necessary connections
described in the Quick Start Guide
or download the User Manual from
www.philips.com/support.
• Switch the SoundBar to the correct source
for other devices.
Adjust the volume
1 Press +/- (Volume) to increase or decrease
a volume level.
• To mute sound, press .
• To restore the sound, press again or
press +/- (Volume).
Volume indicator
• The higher volume level you change to, the
more LED indicators light up. If you do not
press the volume button for three seconds,
the volume indicators light off.
• All the LED indicators blink three
times when a volume level is set to the
maximum or minimum.
• When sound is muted, the current source
indicator blinks.
Choose your sound
This section helps you choose the ideal sound
for your video or music.
Surround sound mode
Experience an immersive audio experience with
surround sound modes.
Page 10
8 EN
1 Press SURR to turn surround mode on
or off.
• On: Create a surround listening
experience.
• Off: Two-channel stereo sound. Ideal
for listening to music.
Sound mode indicator
• If surround mode is turned on, all the LED
indicators light up one by one, with all the
LED indicators on for three seconds. Finally
the current source indicator stays on.
• If surround mode is turned off, all the LED
indicators light up, then light off one by
one. Finally the current source indicator
stays on.
Note
• Virtual surround is applicable for the audio codecs, such
as MP3, PCM and MPEG (except Dolby Digital).
Equalizer
Change the high frequency (treble) and low
frequency (bass) settings of the SoundBar.
1 Press TREBLE +/- or BASS +/- to change
the treble or bass.
Treble/bass indicator
• The more treble/bass you change to, the
more LED indicators light up. If you do
not press the treble/bass button for three
seconds, the treble/bass indicators light off.
• All the LED indicators blink three times
when treble or bass is set to the maximum
or minimum value.
Synchronize video and sound
If the audio and video are not synchronized,
delay the audio to match the video.
1 Press AUDIO SYNC +/- to synchronize
the audio with the video.
• AUDIO SYNC + increases the sound
delay, and AUDIO SYNC - decreases
the sound delay.
Sound delay indicator
• The more delay you change to, the more
LED indicators light up. If you do not press
the sound delay button for three seconds,
the sound delay indicators light off.
Note
• This feature is only applicable to COAXIAL (COAX)
and OPTICAL (OPT) sources.
Night mode
For quiet listening, night mode decreases the
volume of loud sounds when audio is played.
Night mode is only available for Dolby Digital
soundtracks.
1 Press NIGHT to turn night mode on or
off.
Night mode indicator
• If night mode is turned on, all the LED
indicators light up one by one, with all the
LED indicators on for three seconds. Finally
the current source indicator stays on.
• If night mode is turned off, all the LED
indicators light up, then light off one by
one. Finally the current source indicator
stays on.
MP3 player
Connect your MP3 player to play your audio
les or music.
What you need
• An MP3 player.
• A 3.5mm stereo audio cable.
1 Using the 3.5mm stereo audio cable,
connect the MP3 player to the AUDIO IN
connector on your SoundBar.
2 Press AUDIO IN on the remote control.
3 Press the buttons on the MP3 player to
select and play audio les or music.
Page 11
9EN
USB storage devices
Enjoy audio on a USB storage device, such as an
MP3 player and USB ash memory, etc.
What you need
• A USB storage device that is formatted for
FAT or NTFS le systems, and complies
with the Mass Storage Class.
• An MP3 le on a USB storage device
1 Connect a USB storage device to the
SoundBar.
2 Press USB on the remote control.
3 Use the remote control to control play.
Button Action
Start or pause or resume play.
/ Skip to the previous or next track.
USB During play, press to toggle: repeat
one track and repeat off.
Repeat play indicator
• If repeat mode is turned on, all the
LED indicators light up for one
second, then the current source
indicator stays on.
• If repeat mode is turned off, all the
LED indicators light up, then light
off one by one. Finally the current
source indicator stays on.
Note
• This product may not be compatible with certain types
of USB storage device.
• If you use a USB extension cable, USB HUB, or USB
multi-reader, the USB storage device may not be
recognized.
• Digital camera PTP and MTP protocols are not supported.
• Do not remove the USB storage device while it is
being read.
• DRM-protected music les (MP3) are not supported.
• Support a USB port: 5V , 1A.
Play audio through Bluetooth
Through Bluetooth, connect the SoundBar with
your Bluetooth device (such as an iPad, iPhone,
iPod touch, Android phone, or laptop), and then
you can listen to the audio les stored on the
device through your SoundBar speakers.
What you need
• A Bluetooth device which supports
Bluetooth prole A2DP, and with Bluetooth
version as 2.1 + EDR.
• The operational range between the
SoundBar and a Bluetooth device is
approximately 10 meters (30 feet).
1 Press on the remote control to switch
the SoundBar to Bluetooth mode.
» The indicator blinks at a fast rate.
2 On the Bluetooth device, switch on
Bluetooth, search for and select Philips
HTL1190B to start connection (see the
user manual of the Bluetooth device on
how to enable Bluetooth).
• When prompted for a password, enter
"0000".
» During connection, the indicator
blinks at a lower rate.
3 Wait until the indicator lights up.
» If the connection fails, the indicator
blinks continually at a lower rate.
4 Select and play audio les or music on
your Bluetooth device.
• During play, if a call is coming, music
play is paused.
• If your Bluetooth device supports
AVRCP prole, on the remote control
you can press / to skip to a track,
or press to pause/resume play.
5 To exit Bluetooth, select other source.
• When your switch back to Bluetooth
mode, Bluetooth connection remains
active.
Page 12
10 EN
Note
• The music streaming may be interrupted by obstacles
between the device and SoundBar, such as wall, metallic
casing that covers the device, or other devices nearby
that operate in the same frequency.
• If you want to connect your SoundBar with another
Bluetooth device, press and hold on the remote
control to disconnect the currently connected
Bluetooth device.
Auto standby
When playing media from a connected device,
this product automatically switches to standby
after 15 minutes of button inactivity and no
audio play from a connected device.
Apply factory settings
You can reset your SoundBar to the default
setting mode.
1 In mute mode, quickly press AUX two
times.
» The factory settings is restored.
Update software
To continually improve the product, software
upgrade may be offered. Visit ww.philips.com/
support to check if the latest software version
is available.
5 Wall mount
Note
• Improper wall mounting may result in accident, injury or
damage. If you have any query, contact Consumer Care
in your country.
• Before wall mounting, make sure the wall can support
the weight of your SoundBar.
Screw length/diameter
Depending on the type of wall mounting your
SoundBar, make sure that you use screws of a
suitable length and diameter.
See the illustration in the quick start guide on
how to wall mount the SoundBar.
1) Drill two holes on the wall.
2) Secure the dowels and screws in the holes.
3) Hang the SoundBar on the fastening screws.
3.0-3.5mm/0.12”-0.14”
4mm/
0.16”
>25mm/0.98”
Page 13
11EN
6 Product
specifications
Note
• Specications and design are subject to change without
notice.
Amplier
• RMS total output power:
40W RMS (+/- 0.5 dB, 10% THD)
• Frequency response: 40 Hz-20 kHz / ±3 dB
• Signal-to-noise ratio:
> 65 dB (CCIR) / (A-weighted)
• Total Harmonic Distortion: <1%
• Input sensitivity:
• AUX: 2Vrms +/-100mV
• AUDIO IN: 1Vrms +/-100mV
Audio
• S/PDIF Digital audio input:
• Coaxial: IEC 60958-3
• Optical: TOSLINK
• Sampling frequency:
• MP3: 8 kHz, 11 kHz, 12 kHz, 16 kHz,
22 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz
• Constant bit rate:
• MP3: 8 kbps-320 kbps
USB
• Compatibility: Hi-Speed USB (2.0)
• Class support: USB Mass Storage Class
(MSC)
• File system: FAT16, FAT32, NTFS
• Supports MP3 le formats
Bluetooth
• Bluetooth proles: A2DP, AVRCP
• Bluetooth version: 2.1 + EDR
Main unit
• Power supply: 100-240 V~, 50/60 Hz
• Power consumption: 25 W
• Standby power consumption: ≤ 0.5 W
• Dimensions (W x H x D):
865 x 67.8 x 85.5 mm
• Weight: 1.8 kg
• Built-in speakers: 4 x full range
(54.5 mm/2”, 6 ohm)
Remote control batteries
• 1 x AAA-R03-1.5 V
Standby information
• When the product remains inactive for
15 minutes, it automatically switches to
standby or networked standby.
• The power consumption in standby or
networked standby is less than 0.5W.
• To deactivate Bluetooth connection, press
and hold the Bluetooth button on the
remote control.
• To activate Bluetooth connection, enable
Bluetooth connection on your Bluetooth
device, or enable Bluetooth connection via
the NFC tag (if available).
Page 14
12 EN
7 Troubleshooting
Warning
• Risk of electric shock. Never remove the casing of the
product.
To keep the warranty valid, never try to repair
the product yourself.
If you have problems using this product, check
the following points before you request service.
If you still have a problem, get support at
www.philips.com/support.
Main unit
The buttons on the SoundBar do not work.
• Disconnect the SoundBar from the power
supply for a few minutes, then reconnect.
Sound
No sound from SoundBar speakers.
• Connect the audio cable from your
SoundBar to your TV or other devices.
• Reset your SoundBar to its factory settings.
• On the remote control, select the correct
audio input.
• Make sure that the SoundBar is not muted.
Distorted sound or echo.
• If you play audio from the TV through the
SoundBar, make sure that the TV is muted.
Bluetooth
A device cannot connect with the SoundBar.
• The device does not support the
compatible proles required for the
SoundBar.
• You have not enabled the Bluetooth
function of the device. See the user manual
of the device on how to enable the
function.
• The device is not correctly connected.
Connect the device correctly. (see 'Play
audio through Bluetooth' on page 9)
• The SoundBar is already connected with
another Bluetooth device. Disconnect the
connected device, then try again.
Quality of audio play from a connected
Bluetooth device is poor.
• The Bluetooth reception is poor. Move the
device closer to the SoundBar, or remove
any obstacle between the device and the
SoundBar.
The connected Bluetooth device connects and
disconnects constantly.
• The Bluetooth reception is poor. Move the
device closer to the SoundBar, or remove
any obstacle between the device and the
SoundBar.
• Turn off Wi-Fi function on the Bluetooth
device to avoid interference.
• For some Bluetooth, the Bluetooth
connection can be deactivated
automatically to save power. This does not
indicate any malfunction of the SoundBar.
Page 15
13
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by Gibson
is under license. Other trademarks and trade
names are those of their respective owners.
Page 16
Specicationsaresubjecttochangewithoutnotice
2015 © Gibson Innovations Limited. All rights reserved.
This product has been manufactured by, and is sold under the responsibility of Gibson Innovations Ltd., and
Gibson Innovations Ltd. is the warrantor in relation to this product.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used
under license from Koninklijke Philips N.V.
HTL1190BX_77_UM_V1.0
Loading...