Page 1
HTL1180B
www.philips.com/support
Always there to help you
Question?
Contact
Philips
Register your product and get support at
User manual
HTL1180B_79_UM_EN.indd 1 4/27/2015 11:14:47 AM
Page 2
HTL1180B_79_UM_EN.indd 2 4/27/2015 11:14:47 AM
Page 3
Contents
1 Important 2
Help and support 2
Safety 2
Care for your product 3
Care of the environment 3
2 Your SoundBar 4
Main unit 4
Remote control 4
Connectors 5
3 Connect 6
Placement 6
Connect audio from TV and other devices 6
4 Use your SoundBar 7
Adjust the volume 7
Choose your sound 7
MP3 player 8
USB storage devices 9
Auto standby 9
Apply factory settings 9
Update software 9
5 Wall mount 10
6 Productspecications 10
7 Troubleshooting 11
1EN
HTL1180B_79_UM_EN.indd 1 4/27/2015 11:14:47 AM
Page 4
1 Important
Read and understand all instructions before you
use your product. If damage is caused by failure
to follow instructions, the warranty does not
apply.
Help and support
For extensive online support, visit
www.philips.com/support to:
• download the user manual and the quick
start guide
• watch video tutorials (available only for
selected models)
• nd answers to frequently answered
questions (FAQs)
• email us a question
• chat with our support representative.
Follow the instructions on the website to select
your language, and then enter your product
model number.
Alternatively, you can contact Consumer Care
in your country. Before you contact, note down
the model number and serial number of your
product. You can nd this information on the
back or bottom of your product.
Safety
Riskofelectricshockorre!
• Before you make or change any
connections, make sure that all devices are
disconnected from the power outlet.
• Never expose the product and accessories
to rain or water. Never place liquid
containers, such as vases, near the product.
If liquids are spilt on or into the product,
disconnect it from the power outlet
immediately. Contact Consumer Care to
have the product checked before use.
• Never place the product and accessories
near naked ames or other heat sources,
including direct sunlight.
• Never insert objects into the ventilation
slots or other openings on the product.
• Where the mains plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
• Batteries (battery pack or batteries
installed) shall not be exposed to excessive
heat such as sunshine, re or the like.
• Disconnect the product from the power
outlet before lightning storms.
• When you disconnect the power cord,
always pull the plug, never the cable.
Riskofshortcircuitorre!
• For identication and supply ratings, see
the type plate at the back or bottom of
the product.
• Before you connect the product to the
power outlet, ensure that the power
voltage matches the value printed on the
back or bottom of the product. Never
connect the product to the power outlet if
the voltage is different.
Riskofinjuryordamagetothisproduct!
• If the product is transported in
temperatures below 5°C, unpack the
product and wait until its temperature
matches room temperature before
connecting it to the power outlet.
• Parts of this product can be made of
glass. Handle with care to avoid injury and
damage.
Riskofoverheating!
• Never install this product in a conned
space. Always leave a space of at least four
inches around the product for ventilation.
Ensure curtains or other objects never
cover the ventilation slots on the product.
Riskofcontamination!
• Do not mix batteries (old and new or
carbon and alkaine, etc.).
2
EN
HTL1180B_79_UM_EN.indd 2 4/27/2015 11:14:47 AM
Page 5
• Danger of explosion if batteries are
incorrectly replaced. Replace only with the
same or equivalent type.
• Remove batteries if they are exhausted or
if the remote control is not to be used for
a long time.
• Batteries contain chemical substances, they
should be disposed of properly.
Riskofswallowingbatteries!
• The product/remote control may contain
a coin/button type battery, which can be
swallowed. Keep the battery out of reach
of children at all times! If swallowed, the
battery can cause serious injury or death.
Severe internal burns can occur within two
hours of ingestion.
• If you suspect that a battery has been
swallowed or placed inside any part of the
body, seek immediate medical attention.
• When you change the batteries, always
keep all new and used batteries out of
reach of children. Ensure that the battery
compartment is completely secure after
you replace the battery.
• If the battery compar tment cannot be
completely secured, discontinue use of the
product. Keep out of reach of children and
contact the manufacturer.
Care of the environment
Disposal of your old product
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
Do not throw away the product with the
normal household waste at the end of its life,
but hand it in at an ofcial collection point or
recycling. By doing this, you help to preserve the
environment.
This is CLASS II apparatus with double
insulation, and no protective earth provided.
Care for your product
Use only microber cloth to clean the product.
3EN
HTL1180B_79_UM_EN.indd 3 4/27/2015 11:14:47 AM
Page 6
2 Your SoundBar
a
b
c
d
e
g
f
h
i
j
k
Remote control
Congratulations on your purchase, and
welcome to Philips! To fully benet from
the support that Philips offers, register your
SoundBar at www.philips.com/welcome.
Main unit
This section includes an overview of the main unit.
ab c d
a
Switch the SoundBar on or to standby.
b SOURCE
Select an input source for the SoundBar.
c Volume+/-
Increase or decrease volume.
d LED indicators
• STANDBY: Lights up when the
SoundBar is in standby.
• COAXIAL: Lights up when you switch
to coaxial input source.
• OPTICAL: Lights up when you switch
to optical input source.
• AUX: Lights up when you switch to
analog input source.
• AUDIO IN: Lights up when you switch
to audio input source (3.5mm jack).
• USB: Lights up you switch to USB source.
4
EN
This section includes an overview of the
remote control.
a (Standby-On)
Switch the SoundBar on or to standby.
b Source buttons
• COAX: Switch your audio source to
the coaxial connection.
• OPT: Switch your audio source to the
optical connection.
• AUX: Switch your audio source to the
AUX connection.
• AUDIO IN: Switch your audio source
to the MP3 connection (3.5mm jack).
• USB: Switch your audio source to the
USB connection.
c REPEAT
Select or turn off repeat mode in USB
mode.
HTL1180B_79_UM_EN.indd 4 4/27/2015 11:14:48 AM
Page 7
d +/- (Volume)
f
Increase or decrease volume.
e
Mute or restore volume.
f BASS +/-
Increase or decrease bass.
g NIGHT
Turn night mode on or off.
h TREBLE +/-
Increase or decrease treble.
i SURR
Toggle between stereo and virtual
surround sound.
j AUDIO SYNC +/-
Applicable to COAXIAL (COAX) and
OPTICAL (OPT) sources only. Increase or
decrease audio delay.
k Play buttons
•
: Play, pause or resume play in USB
mode.
•
/ : Skip to the previous or next
track in USB mode.
a DIGITAL IN-OPTICAL
Connect to an optical audio output on the
TV or a digital device.
b AUX
Connect to an analog audio output on the
TV or an analog device.
c COAXIAL
Connect to a coaxial audio output on the
TV or a digital device.
d
Audio input from a USB storage device.
e AUDIO IN
Audio input from, for example, an
MP3 player (3.5mm jack).
f AC MAINS~
Connect to the power supply.
Connectors
This section includes an overview of the
connectors available on your SoundBar.
a
b
c
d
e
HTL1180B_79_UM_EN.indd 5 4/27/2015 11:14:50 AM
5EN
Page 8
3 Connect
Connect audio from TV and other devices
This section helps you connect your SoundBar
to a TV and other devices.
For information about the basic connections of
your SoundBar and accessories, see the quick
start guide.
Note
For identication and supply ratings, refer to the type
•
plate at the back or bottom of the product.
• Before you make or change any connections, make sure
that all devices are disconnected from the power outlet.
Placement
Place your Soundbar as shown below.
Play audio from TV or other devices through
your Soundbar.
Use the best quality connection available on
your TV and other devices.
Option 1: Connect audio through a
digital optical cable
Best quality audio
TV
1 Using an optical cable, connect the
OPTICAL connector on your SoundBar to
the OPTICAL OUT connector on the TV
or other device.
• The digital optical connector might be
labeled SPDIF or SPDIF OUT.
Option 2: Connect audio through a
digital coaxial cable
Best quality audio
6
EN
HTL1180B_79_UM_EN.indd 6 4/27/2015 11:14:51 AM
Page 9
1 Using a coaxial cable, connect the
COAXIAL connector on your SoundBar
to the COAXIAL/DIGITAL OUT
connector on the TV or other device.
• The digital coaxial connector might be
labeled DIGITAL AUDIO OUT.
Option 3: Connect audio through
analog audio cables
Basic quality audio
DVD
1 Using an analog cable, connect the AUX
connectors on your SoundBar to the
AUDIO OUT connectors on the TV or
other device.
4 Use your
SoundBar
This section helps you use the SoundBar to play
audio from connected devices.
Before you start
• Make the necessary connections
described in the Quick Start Guide
or download the User Manual from
www.philips.com/support.
• Switch the SoundBar to the correct source
for other devices.
Adjust the volume
1
Press +/- (Volume) to increase or decrease
a volume level.
• To mute sound, press
• To restore the sound, press
press +/- (Volume).
Volume indicator
• The higher volume level you change to, the
more LED indicators light up. If you do not
press the volume button for three seconds,
the volume indicators light off.
• All the LED indicators blink three
times when a volume level is set to the
maximum or minimum.
• When sound is muted, the current source
indicator blinks.
.
again or
Choose your sound
This section helps you choose the ideal sound
for your video or music.
7EN
HTL1180B_79_UM_EN.indd 7 4/27/2015 11:14:52 AM
Page 10
Surround sound mode
Experience an immersive audio experience with
surround sound modes.
1 Press SURR to turn surround mode on
or off.
• On: Create a surround listening
experience.
• Off: Two-channel stereo sound. Ideal
for listening to music.
Sound mode indicator
• If surround mode is turned on, all the LED
indicators light up one by one, with all the
LED indicators on for three seconds. Finally
the current source indicator stays on.
• If surround mode is turned off, all the LED
indicators light up, then light off one by
one. Finally the current source indicator
stays on.
Equalizer
Change the high frequency (treble) and low
frequency (bass) settings of the SoundBar.
1 Press TREBLE +/- or BASS +/- to change
the treble or bass.
Treble/bass indicator
• The more treble/bass you change to, the
more LED indicators light up. If you do
not press the treble/bass button for three
seconds, the treble/bass indicators light off.
• All the LED indicators blink three times
when treble or bass is set to the maximum
or minimum value.
Synchronize video and sound
If the audio and video are not synchronized,
delay the audio to match the video.
1 Press AUDIO SYNC +/- to synchronize
the audio with the video.
• AUDIO SYNC + increases the sound
delay, and AUDIO SYNC - decreases
the sound delay.
Sound delay indicator
• The more delay you change to, the more
LED indicators light up. If you do not press
the sound delay button for three seconds,
the sound delay indicators light off.
Note
This feature is only applicable to COAXIAL (COAX)
•
and OPTICAL (OPT) sources.
Night mode
For quiet listening, night mode decreases the
volume of loud sounds when audio is played.
Night mode is only available for Dolby Digital
soundtracks.
1 Press NIGHT to turn night mode on or
off.
Night mode indicator
• If night mode is turned on, all the LED
indicators light up one by one, with all the
LED indicators on for three seconds. Finally
the current source indicator stays on.
• If night mode is turned off, all the LED
indicators light up, then light off one by
one. Finally the current source indicator
stays on.
MP3 player
Connect your MP3 player to play your audio
les or music.
What you need
• An MP3 player.
• A 3.5mm stereo audio cable.
1 Using the 3.5mm stereo audio cable,
connect the MP3 player to the AUDIO IN
connector on your SoundBar.
2 Press AUDIO IN on the remote control.
3 Press the buttons on the MP3 player to
select and play audio les or music.
8
EN
HTL1180B_79_UM_EN.indd 8 4/27/2015 11:14:52 AM
Page 11
USB storage devices
Auto standby
Enjoy audio on a USB storage device, such as an
MP3 player and USB ash memory, etc.
What you need
• A USB storage device that is formatted for
FAT or NTFS le systems, and complies
with the Mass Storage Class.
• An MP3 le on a USB storage device
1 Connect a USB storage device to the
SoundBar.
2 Press USB on the remote control.
3 Use the remote control to control play.
Button Action
Start or pause or resume play.
/ Skip to the previous or next track.
REPEAT During play, press to toggle: repeat
all tracks and repeat off.
Repeat play indicator
• If repeat mode is turned on, all
the LED indicators blink for three
times, then the current source
indicator stays on.
• If repeat mode is turned off, all
the LED indicators light up, then
light off one by one. Finally the
current source indicator stays on.
When playing media from a connected device,
this product automatically switches to standby
after 15 minutes of button inactivity and no
audio play from a connected device.
Apply factory settings
You can reset your SoundBar to the default
setting mode.
1 In mute mode, quickly press AUX two
times.
» The factory settings is restored.
Update software
To continually improve the product, software
upgrade may be offered. Visit ww.philips.com/
support to check if the latest software version
is available.
Note
This product may not be compatible with certain types
•
of USB storage device.
• If you use a USB extension cable, USB HUB, or USB
multi-reader, the USB storage device may not be
recognized.
• Digital camera PTP and MTP protocols are not suppor ted.
• Do not remove the USB storage device while it is
being read.
• DRM-protected music les (MP3) are not supported.
• Support a USB por t: 5V , 1A.
9EN
HTL1180B_79_UM_EN.indd 9 4/27/2015 11:14:52 AM
Page 12
5 Wall mount
3.0-3.5mm/0.12”-0.14”
Note
Improper wall mounting may result in accident, injur y or
•
damage. If you have any query, contact Consumer Care
in your country.
• Before wall mounting, make sure the wall can suppor t
the weight of your SoundBar.
Screw length/diameter
Depending on the type of wall mounting your
SoundBar, make sure that you use screws of a
suitable length and diameter.
4mm/
0.16”
>25mm/0.98”
See the illustration in the quick start guide on
how to wall mount the SoundBar.
1) Drill two holes on the wall.
2) Secure the dowels and screws in the holes.
3) Hang the SoundBar on the fastening screws.
6 Product
specifications
Note
Specications and design are subject to change without
•
notice.
Amplier
• RMS total output power:
40W RMS (+/- 0.5 dB, 10% THD)
• Frequency response: 40 Hz-20 kHz / ±3 dB
• Signal-to-noise ratio: > 65 dB (CCIR) /
(A-weighted)
• Total Harmonic Distortion: <1%
• Input sensitivity:
• AUX: 2Vrms +/-100mV
• AUDIO IN: 1Vrms +/-100mV
Audio
• S/PDIF Digital audio input:
• Coaxial: IEC 60958-3
• Optical: TOSLINK
• Sampling frequency:
• MP3: 8 kHz, 11 kHz, 12 kHz, 16 kHz,
22 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz
• Constant bit rate:
• MP3: 8 kbps-320 kbps
10
HTL1180B_79_UM_EN.indd 10 4/27/2015 11:14:52 AM
USB
• Compatibility: Hi-Speed USB (2.0)
• Class support: USB Mass Storage Class
(MSC)
• File system: FAT16, FAT32, NTFS
• Supports MP3 le formats
EN
Page 13
Main unit
• Power supply: 100-240 V~, 50/60 Hz
• Power consumption: 25 W
• Standby power consumption: ≤ 0.5 W
• Speaker impedance: 8 ohm (full range)
• Speaker drivers: 4 x 54.5 mm (2")
• Dimensions (W x H x D):
865 x 67.8 x 85.5 mm (34.1" x 2.7" x 3.4")
• Weight: 1.8 kg / 3.96 lbs
Remote control batteries
• 1 x AAA-R03-1.5 V
7 Troubleshooting
Warning
•
Risk of electric shock. Never remove the casing of the
product.
To keep the warranty valid, never try to repair
the product yourself.
If you have problems using this product, check
the following points before you request service.
If you still have a problem, get support at
www.philips.com/support.
Main unit
The buttons on the SoundBar do not work.
• Disconnect the SoundBar from the power
supply for a few minutes, then reconnect.
Sound
No sound from SoundBar speakers.
• Connect the audio cable from your
SoundBar to your TV or other devices.
• Reset your SoundBar to its factory settings.
• On the remote control, select the correct
audio input.
• Make sure that the SoundBar is not muted.
Distorted sound or echo.
• If you play audio from the TV through the
SoundBar, make sure that the TV is muted.
11EN
HTL1180B_79_UM_EN.indd 11 4/27/2015 11:14:52 AM
Page 14
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
12
HTL1180B_79_UM_EN.indd 12 4/27/2015 11:14:53 AM
Page 15
Warranty against Defects
In this warranty:
We or us means Gibson Innovations ARBN 165 105 975 , and our contact details are set out at the end of this
warranty;
You means the purchaser or the original end-user of the Goods;
Supplier means the aut horised distributor or retailer of the Goods that sold you the Goods in Australia or New
Zealand; and
Goods means the product or equipment which was accompanied by this warranty and purchased in Austral ia or New
Zealand.
If you require assistance with the operation of the product, its features or specifications please call the Philips
Consumer Care Centre on 1300 850 633 in Australia or 0800 639 953 in New Zealand.
Australia: Our Goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund f or a major failure and for compensation for any other reasonably foreseeable loss
or damage. You are also entitled to have the Goods repaired or replaced if the goods fail to be of acceptable quali ty
and the failure does not amount to a major failure. This is not a complete statement of your legal rights as a consumer.
New Zealand: Our Goods come with guarantees that cannot be excluded under the Consumer Guarantees Act 1993.
This guarantee applies in additi on to the conditions and guarantees implied by that legislation.
Additional Warranty:
In addition to the rights and remedies that you have under the Australi an Consumer Law, Consumer Guarantees Act
of New Zealand or any other applicable law, we provide the following warranty against defects:
1. If, during the fi rst 12 months from their date of purchase from the Supplier (Warranty Period), the Goods prove
defective by reason of improper workmanship or materials and none of your statutory rights or remedies apply, we
will repair or replace the Goods without charge.
2. We do not have to repair or replace the Goods under this Additional Warranty if the Goods have been used for a
commercial purpose; misused, improperly or inappropriately installed, operated or repaired; abused; damaged; or
not maintained in accordance with the manufacturer’s instructions.
3. Even when we do not have to repair or replace the Goods, we may decide to do so anyway. In some cases, we
may decide to substitute the Goods with a similar alternative product of our choosing. All such decisions are at
our absolute discretion.
4. All such repaired, replaced or substituted Goods continue to receive the benefit of this Additional Warranty for the
time remaining on the original Warranty Period.
5. This Additional Warranty is limited to repair, repl acement or substitution only. As far as the law permits, we will not
be liable for any loss or damage caused to property or persons arising from any cause whatsoever.
6. In order to claim under this Additional Warranty you must telephone us on 1300 850 633 in Australia or 0800 639
953 in New Zealand within the Warranty Period. You will be asked for details of the Goods, a description of the
defect and your personal details. Upon accepting your claim, we shall assist you with either returni ng the Goods to
the Supplier for replacement or to the most convenient Philips Authorised Service Centre for your Goods to be
repaired. In some case we may require that you return to the Goods to us (at the address below) for repair,
replacement or substituti on.
∗ All returned Goods must be accompanied by satisfactory proof of purchase which clearly indicates the name and
address of the Supplier, the date and place of purchase and identifies product. It is best to provide a legible and
unmodified receipt or sales invoice.
∗ You must bear any expense for return of the Goods or otherwise associated with making your claim under this
Additional Warranty.
7. This warranty is only valid and enforceable in Australia and New Zealand.
Contact us or the place of purchase for further details.
Australia
Gibson Innovations New Zealand
Suite 22a 33 Waterloo Rd
Nth Ryde, NSW 2113
Consumer Care: 1300 850 633 Consumer Care: 0800 639 953
E-mail: pccw.woox@gibson.com Email: pccw.woox@gibson.com
Website: www.philips.com/support Website: www.philips.com/support
Apr 2015
13
HTL1180B_79_UM_EN.indd 13 4/27/2015 11:14:53 AM
Page 16
Specicationsaresubjecttochangewithoutnotice
2015 © Gibson Innovations Limited. All rights reserved.
This product has been manufactured by, and is sold under the responsibility of Gibson Innovations Ltd., and
Gibson Innovations Ltd. is the warrantor in relation to this product.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under
license from Koninklijke Philips N.V.
HTL1180B_79_UM_V1.0
HTL1180B_79_UM_EN.indd 14 4/27/2015 11:14:53 AM
Loading...