Philips HR8374 Service Manual

City Line Sydney Vacuum cleaner

HR 8374

Philips Domestic Appliances and Personal Care

Service Manual

PRODUCT INFORMATION

- Maximum air displacement : 34 l/sec

- Maximum vacuum water column : 280 cm

- Power consumptio (IEC) 225V : 1400 W

- Dust storage capacity : 2 litres

- Cord length (depends on version) : 6 m

- Filter system : 6 fi lters

- Dimensions cleaner : 37 x 28 x 23 cm

- Weight accessoiries : 4.3 kg

- Noise : 80 dB

- Colour : Light blue

- Electronic controled motor rpm

- Cordwinder build-in with fl at cord

- Dustbag-full indicator in dustcover

OPTIONAL

Combi exhaust air fi lter (4322 004 22240)
Sydney cotton dustbag HR 6997 (8836 997 01010)
Sydney 3M dustbag HR 6999 (8836 999 90010)
Sydney paper dustbags HR 6999 (8836 999 01010)
Turbo brush con. HR 6988 (4822 479 20196)
Polishing nozzle con. HR 8040 (4322 004 22330)

This product meets the requirements regard­ing interference suppression on radio and TV.

After the product has been repaired, it should
function properly and has to meet the safety
requirements as offi cially laid down at this
moment.

SERVICE INFORMATION

- To open the appliance, fi rst remove the screws A,B,C,D.

- To reach the motor remove the screws E.

- To disassemble the cordwider use Torx screw driver no T10,
which is one of set consisting of T20, T15, T10, T9, T8, T7 and
T6 = 4822 395 50145.

- Give attention that the contact fi ngers (item 45) are placed on the
cord-winder shaft in such a way that the pressure point of the
cordwinder knob to the cord winderlever (item 40) is vertical.

- The spare parts have been standardized as much as possible.

- Component confi guration on exploded view may differ in case
of specifi c versions, however, the actual components are distin­guished by means of code numbers.

- Item 1 Cotton dustbag is used in those countries where paper
dustbags are not available

- Item 41 Cord-winder spring unit is provided with a long spring,
both long and short cords can be used in combination with this
spring.

- Cordwinder spring has to be tensioned till maximum minus
approx. 1,5 revolution.

- First remove the two screws
B of (item 15) hinge turn +
window. Remove (item 15) hinge
turn + window from (item 3)
upper housing by means of a
fl at instrument (e.g. screw driver)
as shown (to prevent demage).
The hinge turn + window has
snaps which fi ts into the upper
housing. Vario / knob turn
(item 10 ) can now be separated
as shown in next drawing.

- Place the knob turn in line with
the adjuster item 10A. Hook
(item 15) hinge turn + window
into the (item 3) upper housing.
Use the 2 screws (item B) to
fasten item 15 to item 3. Place
the cover of vario / knob turn
(item 10) in the correct way;
only on one way possible.

B

1

B

2

4

B

3

B

2

1

Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification

4322 277 00362
02/08

HR 8374
Pos. 12 nc description

1 8836 999 90010 Sydney 3M dustbags
8836 999 01010 Sydney paper dustbags (opt.)
8836 997 01010 Sydney cotton dustbag (opt.)
2 4322 009 07670 dustbag holder
3 4322 009 07680 upperhousing (grey)

4 4322 001 73150 inletrubber
5 4322 003 17250 nose piece (grey)
6 4322 005 11860 caster dish assy
7 4322 003 17230 fi xing pin
8 4322 009 07690 lower housing (grey)

9 4322 005 09030 handle turn
10 4322 009 07780 vario / knob turn (pearl blue)
10A 4322 003 11730 adjuster
11 4322 009 07790 dust cover assy (blue/white)
12 4322 001 72900 motor buffer

13 4322 001 73160 m.c. sealing
14 4322 000 35360 duo fi lter
14A 4322 009 08460 duo fi lter and holder
15 4322 009 07700 hinge turn + window (grey)
16 4322 009 07800 cord outlet combi (grey)

17 4322 003 17670 back grille (grey)
18 4322 004 22240 combi fi lter
19 4322 009 07810 rear wheel (blue/white)
20 4322 003 17310 knobs (grey)
21 4322 000 09750 pedal spring

22 4322 006 22500 PCB ans 110 V turn
4322 006 22440 PCB ans 220 - 240 V turn
22A 4322 006 50600 switch (soldered version)
23 4322 001 73270 AP cooling connection
24 4322 003 17290 motor cap combi (grey)

25 4322 001 72780 buffer ring front
26 4322 006 97400 motor ans 110 V
4322 009 06430 motor ans 220 - 240 V
27 4322 003 11990 receptical housing
28 4322 009 07520 motor foam / disc / ans
29 4322 009 07820 clamp / lock (grey)

Pos. 12 nc description

40 4322 003 06620 push rod
41 4322 009 07610 reelhalf springside
42 4322 001 72360 brake tyre
43 4322 009 07640 base plate
44 4322 009 07620 reelhalf contactside

45 4322 009 07630 contact plate
46 4322 006 01880 Argentina L = 6.3 m
4322 006 01380 Australia L = 6.3 m
47 4322 006 01770 Japan / Taiwan L = 5.3 m
48 4322 006 01370 H.K. / U.K. L = 6.3 m

49 4322 006 01400 Euro 4.8 mm L = 6.3 m
50 4322 006 01480 Swiss L = 6.3 m
51 4322 006 01430 Italy L = 6.3 m
55 4322 003 13010 crevice nozzle
56 4322 004 21160 small nozzle

57 4322 004 21170 plumeau
58 4322 004 21810 big nozzle RD262 con.
59 4322 003 10070 tube clip (opt.)
60 4322 002 22610 metal tube (opt.)
61 4322 009 05410 clip telesc. tube

62 4322 004 21050 telescopic tube
63 4341 004 20240 bend + hose ass’y (standard)
64 4322 003 17380 bend

M

SPEED

CONTROL UNIT

C

CORD WINDER