Philips HR2728/40, HR2726/90, HR2726, HR2727, HR2728 User Manual
Register your product and get support at
www.philips.com/welcome
Meat mincer
HR2726
HR2727
HR2728
English 3
Român 25
47
71
3
English
EN
Contents
1 Important 4
Safety system 4
Electromagnetic elds (EMF) 5
Recycling 5
2 Introduction 5
3 What’s in the box 6
4 Mince meat 8
Assemble 8
Mince meat 9
Disassemble 9
Recipe 10
5 Make sausages 10
Assemble 10
Make sausages 11
Disassemble 12
Recipe 12
6 Make kebbe 13
Assemble 13
Make kebbe 14
Disassemble 14
Recipe 14
7 Make cookies (HR2728 only) 15
Assemble 15
Make cookies 16
Disassemble 16
8 Cut vegetables and crush ice
(HR2728 only) 17
Assemble 17
Cut vegetables 18
Crush ice 19
Disassemble 19
9 Cleaning and maintenance 20
Clean 20
Replace the gear 21
Store the product 21
10 Troubleshooting 22
4
• Do not insert your ngers in the metal
drum while the appliance is running.
Caution
• The appliance is intended for household
use only.
• Before you connect the appliance to the
mains, make sure that the appliance is
assembled correctly.
• Never use any accessories or parts from
other manufacturers or that Philips does
not speci cally recommend. If you use
such accessories or parts, your guarantee
becomes invalid.
• Always switch the appliance off by pressing
the
/ button.
• Do not let the appliance run unattended.
• Do not exceed the maximum operating
time of 10 minutes at all applications.
• Do not use the
button with the plastic
hopper.
• Noise level: Lc = 87 dB [A]
Safety system
This appliance is equipped with overheat
protection. If the appliance overheats, it switches
off automatically. Unplug the appliance and let
it cool down until room temperature. Then, put
the mains plug back into the power outlet and
switch on the appliance again. Please contact
your Philips dealer or an authorized Philips
service center if the overheat protection is
activated too often.
The appliance is also equipped with mechanical
protection. To protect the motor, the plastic
gear has been designed to break if bones or
utensils are fed into the appliance. When this
happens, simply remove the gear and
exchange it.
1 Important
Read these instructions for use carefully before
using the appliance and save them for future
reference.
Danger
• Do not immerse the motor unit in water
nor rinse it under the tap.
• Do not connect the appliance to a timer
switch.
Warning
• Before you connect the appliance to
the power, make sure that the voltage
indicated on the bottom of the appliance
corresponds to the local power voltage.
• If the power cord, the plug, or other parts
are damaged, do not use the appliance.
• If the power cord is damaged, you must
have it replace by Philips, a service center
authorized by Philips, or similarly quali ed
person to avoid a hazard.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
• For their safety, do not allow children to
play with the appliance.
• Be very careful when you handle the cutter,
especially when you remove it from the
worm shaft and during cleaning. The cutting
edges are very sharp!
• Before you remove any accessory, switch
the appliance off and unplug it.
• Do not use your ngers or an object
(e.g. a spatula) to push ingredients into
the hopper while the appliance is running.
Only the pushers are to be used for this
purpose.
EN
5
English
2 Introduction
Congratulations on your purchase and welcome
to Philips! To fully bene t from the support that
Philips offers, register your product at
www.philips.com.
With this product, you can
• mince meat
• make sausages
• make kebbe
• make cookies ( HR2728 only )
• cut vegetables and grate cheese
( HR2728 only )
• crush ice ( HR2728 only )
Electromagnetic elds (EMF)
This Philips appliance complies with all
standards regarding electromagnetic elds
(EMF). If handled properly and according to the
instructions in this user manual, the appliance is
safe to use based on scienti c evidence available
today.
Recycling
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
When you see the crossed-out wheel bin
symbol attached to a product, it means the
product is covered by the European Directive
2002/96/EC:
Never dispose of your product with other
household waste. Please inform yourself about
the local rules on the separate collection of
electrical and electronic products. The correct
disposal of your old product helps prevent
potentially negative consequences on the
environment and human health.
EN
6
e Power cord
f Feeding tray
• Plastic for HR2726
• Metal for HR2727 and HR2728
g Pusher for the metal hopper
h Metal hopper
i Extra gear for the worm shaft
j Worm shaft
k Screw ring
3 What’s in the box
a Hopper release button
• Press and hold it when you remove
the hopper.
b Motor unit
c
/
• Switch off or on the appliance.
d
/ Reverse
• Press it to reverse the motor. (only
active when the switch is in the “
“
position)
cd
b
a
ji
hg
f
e
k
EN
7
English
q Cookie maker ( for HR2728 )
• A : Cookie separator
• B : Cookie shaper
r Pusher for the plastic hopper
( for HR2728 )
s Plastic hopper ( for HR2728 )
t Metal drums ( for HR2728 )
• A : Coarse grater drum
• B : Fine grater drum
• C : Slicer drum
• D : Ice drum
u Dust cover
v Accessories tray ( for HR2726
and HR2727 )
w Accessories tray ( for HR2728 )
l Grinding discs
• A : Coarse grinding disc
(diameter of 8 mm)
• B : Fine grinding disc
(diameter of 4 mm)
m Cutter/Knife
n Sausage horns
• A : Large sausage horn
(diameter of 22 mm)
• B : Small sausage horn
(diameter of 12 mm)
o Sausage separator
p Kebbe maker
• A : Kebbe separator
• B : Kebbe shaper
pq
on
B
A
A
B
A
B
A
B
s
t
r
A
B
C
D
u
w
v
lm
EN
8
2 Fix the hopper onto the motor unit.
1) Press and hold the button.
2) Push the hopper towards the motor
unit and turn it anti-clockwise until you
hear a “click”.
3 Fix the feeding tray onto the hopper.
4 Connect the power plug to the power
supply.
Tip
•
Make sure that the projections on the hopper align
with the notches of the motor.
• Never use the cutter in combination with any plastic
accessory.
• Remove the protective cover from the cutter before use.
• Make sure that the cutting edge of the cutter points
outwards.
4 Mince meat
Before you use the appliance for the rst time,
thoroughly clean the parts that come into
contact with food.
Assemble
Unplug this appliance before the assembly.
1 Assemble the hopper and accessories.
1) Push the worm shaft into the cutter
housing.
2) Fix the cutter onto the worm shaft.
3) Fix the grinding disc onto the worm
shaft and the hopper.
4) Turn the screw ring clockwise to fasten it.
EN
Loading...