Philips HR2702 User Manual

HR 2702
English Page 4
• Keep pages 3 and 14 open when reading these operating instructions.
Français Page 6
• Pour le mode d'emploi: dépliez les pages 3 et 14.
Deutsch Seite 8
Nederlands Pagina 10
• Sla bij het lezen van de gebruiksaanwijzing de pagina's 3 en 14 op.
Español Página 12
• Desplegar las páginas 3 y 14 al leer las instrucciones de manejo.
2
C
D F
CA
K
E
HIJ
LN
G
1
M
B
3
General description (fig. 1)
A Cord storage B On / off switch safety guard (button) C On / Off switch (button) D Circular blade (stainless steel)
(4822 690 40311)*
E Blade lock F Blade cover (4822 466 10792)* G Remainders holder (4822 256 10158)* H Carriage (4822 466 10794)* ISupport table (4822 466 10795)* J Stop plate (4822 466 10793)* KCutting width control (max. 24 mm) L Suction pad feet (4822 462 10641)* M Tray (4822 450 10075)* N Carriage lock (slide)
Spare parts are available for replacement. Apply to your dealer referring to the service number (...)*.
Making ready for use
- Unwind the mains cord to the desired length and secure it (fig. 2).
- Place the appliance on a smooth stable surface. Press down so that the suction pad feet adhere tightly for maximum stability.
- Attach the carriage to the support table (fig. 3-4).
- Attach the remainders holder to the carriage (fig. 5).
Switching on and off
The switch guard locks the On / Off button, to prevent unintended switching on.
- Press and hold the switch guard. Push down the On / Off button (fig. 6).
- Release the switch guard (fig. 7). As long as the On / Off button remains in down position, the appliance is switched on.
- To switch off, just release the On / Off button (fig. 8). The switch guard springs back into its original position.
Cutting width setting
- Set the desired cutting width (max. 24 mm) by rotating the control knob. Refer to the the scale (fig. 9-10).
For safety, always rotate the control knob anti-clockwise until it stops. (Minimum cutting width.)
Hinged carriage and remainders lock
For safety: Always place the remainders holder on the carriage for cutting rest pieces.
Use
The universal cutter slices bread, meat, sausage,cheese, vegetables and fruit easily (fig. 11-12). Press the food to be sliced lightly against the stop plate and slide slowly against the running blade. Please note: The appliance is intended for domestic use. Do not operate the appliance longer than 10 minutes without a pause.
4
English
Important
Read the instructions in conjunction with the illustrations before using the appliance.
Care must be taken when handling the circular blade as it is very sharp.
Do not allow children to operate the appliance.
Remove the mains plug from the wall socket after use.
If the mains cord of this appliance is damaged, it must only be replaced by Philips or their service representative, as special tools and/or parts are required.
Prior to initial use, clean all the parts which come into contact with food.
Never immerse the motor unit in water or any other liquid. Do not rinse either.
Keep these instructions for future reference.
CIeaning
• Switch off and remove the mains plug from the wall socket before cleaning. Wait for the circular blade to come to a complete standstill.
• Never immerse the basic appliance (i.e. the part containing the motor) into water or any other fluid. Do not rinse either.
• Clean the appliance with a damp cloth immediately after use, including the circular blade. Do not use any scouring cleaning materials. Do not clean in a dishwasher.
Attention: the blade is very sharp.
Circular blade
To disassemble the circular blade:
- Remove the blade cover (fig. 13).
- Rotate the blade lock a quarter turn clockwise (fig. 14). When the lock is in a vertical position the circular blade can be removed (fig. 15).
To reassemble the circular blade:
- Rotate the blade lock a quarter turn anti­clockwise. When the lock is in a horizontal position the circular blade is fixed.
Ensure that the blade is safely assembled before switching on.
- Replace the blade cover (fig. 16-17).
Stop plate
To disassemble the stop plate:
- Turn the control knob anti-clockwise until it stops (fig. 18).
- Then take off the stop plate (fig. 19).
To reassemble the stop plate:
- Insert the stop plate, press on lightly and turn the control knob clockwise (fig. 20).
Carriage lock (slide)
Before storing the appliance you can fixate the carriage in the foremost position (fig. 21).
For U.K. only:
Fitting a different plug
This appliance is fitted with a BS 1363 13 Amp. plug. Should you need to replace the plug, connect the wires as follows:
Green/yellow wire to the Earth terminal (E) of the new plug. Brown wire to the Live (L) terminal of the new plug. Blue wire to the Neutral (N) terminal of the new plug.
Always fit the same value of fuse as that originally supplied with your appliance. Only use BS 1362 approved fuses. As a guide only: Appliances under 700 W can have a 3 Amp. fuse (red) and all others should have a 13 Amp. fuse (brown).
When disposing of an old plug (particularly the moulded type which has been cut from the mains cord) always remove the fuse as the plug could be dangerous if ever inserted in a live socket.
5
Loading...
+ 11 hidden pages