Philips HR2305B Service Manual

Cucina Ice-cream maker

HR 2305/B

Philips Domestic Appliances and Personal Care

Service Manual

PRODUCT INFORMATION

Power consumption motor : 30 W
Voltage : 220/230 V, 50-60 Hz
Length of mains cord : 140 cm
Freezing time of cooling disc : 18 hrs
Weight of product : 3.4 kg
Dimensions product l x w x h : 23 x 25 x 27 (cm)
Type no. cooling disc : HR 2968
Speeds : 2

Cooling disc/container is to be kept in a 3 or 4-star freezer or
freezing compartment of the refrigerator.

The stirrer should actually be functioning when the bowl is
being fi lled otherwise the ingredients will immediately freeze
onto the cooling disc.

Safety shut-off

The ice-cream maker is equipped with a safety shut-off.
This device automatically switches off the appliance after
120 minutes of operation, or if overloading occurs.
Cooling down time: approx. 55 min.

Soft

Compact

wt

wt/rd

wt/rd (x)

rdrd rd

2134

Ice-cream selector switch

When the “soft ice” switch is pressed, the stirrer will start
rotating at a relatively high speed (approx. 70 rpm, gradually
decreasing to approx. 50 rpm., depending upon the mixture).
After approx. 20 minutes, the green pilote light will start to blink.
Up to 10 minutes after switching on, you can switch from making
“Compact ice” to making “Soft ice” (or the other way round).
If “Soft ice” has been selected and the ice-cream maker is not
been switched off after 30 minutes, the appliance will reduce
stirrer speed to keep the “Soft ice” longer in optimum condition.

When the “Compact ice” switch is pressed, the stirrer will start
rotating at a relatively low speed (approx. 21 rpm).
After approx. 40 minutes, the green pilot light will start to blink.

The blinking pilot light means that the minimum processing time
for a standard quantity of the selected type of ice cream has
elapsed.

SERVICE INFORMATION

- Gas pressure may cause the cooling disc to bulge out
so that it is impossible to assemble it into the appliance.
If this has happened proceed as follows:

1. Remove plug (item 16) which is fi xed with snap tabs.

2. Bring the cooling disc back into its original fl at shape and,

while doing so, insert a new plug (item 16).

- Use grease 4822 390 20004 on the metal gearwheel shafts
in the gearbox.

- Motor control without de-soldering (see wiring diagram):
Resistance must be between 1-2 = 440 ± 50 ohm and
between 3-4.

- If a repair has been executed, make sure that all functions of
the appliance are working correctly.

Hall

Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification

DAP0153

4322 277 00155
99/12

PCS 101 330

HR 2305/B

1

2

3

14

8

9

10

11

15

16

17

4

5

6

7

1 4203 065 62360 upper housing
2 4822 321 62806 hall assy
3 4822 214 70585 pcb 220 V
4 4822 522 10477 gear box
5 4203 065 62370 fl ex

12

13

DAP 0151

11 4822 466 62531 buffer
12 4822 466 62608 sealing ring
13 4203 065 62390 lower housing
14 4203 065 62400 container cover
15 4203 065 62410 stirrer

18

19

PCS 101 330

6 4822 502 30005 screw 3.5 x 25
7 4203 065 62380 coupling assy
8 4822 502 30054 screw 2.5 x 13
9 4822 361 30446 motor 220 V
10 4822 522 33531 drive gear wheel

16 4822 267 31056 plug cooling-disc
17 4822 511 90025 cool disc
18 4203 065 62420 container
19 4822 462 40374 stud
DFU 4203 064 12000