Philips HR1821AB, HR1821 Service Manual

Juice extractor

HR1821/A
HR1821/B

Philips Domestic Appliances and Personal Care

Service Manual

PRODUCT INFORMATION

HR1821 = juice extractor with detachable pulp container + cup

Power consumption : 220 W
Voltage : 110 V, 50 - 60 Hz

120 - 127 V, 50 - 60 Hz
220 - 240 V, 50 - 60 Hz

Volume (of juice cup) : 400 ml
Volume (of pulp container) : 500 ml
Dimensions of product : 220 x 190 x 278 mm
Dimensions of fancy box : 260 x 215 x 360 mm
Weight fancy box : 2.9 kg
Cord length : 1.1 m

Foam separator is integated with juice cup lid
Spout is detachable for easy cleaning

SERVICE INFORMATION

- This appliance is intended for household use only.

- Always check the sieve. If any cracks or damage are
detected, replace the sieve.

- Do not let the appliance run for more then two minutes
without interruption, allow it to cool down for two minutes
before you continue.

- Do not clean any of the parts in a dishwasher.

- Do not use abrasive cleaning agents, scourers, wiretool,
acetone, alcohol etc.

- The appliance is provided with a safety system.
If all parts are not properly mounted together; the
appliance will not work.
Check whether the parts have been connected in the right
way. But turn off the power fi rst.

This product meets the requirements regard­ing interference suppression on radio and TV.

The intended sequence of putting the appliance together by
user is as follows:

1. Snap juice spout onto pulp collector

2. Place pulp collector in position

3. Place sieve

4. Place lid on pulp collector (by aligning the hook on lid and
the corresponding rectangluar hole on pulp collector)

5. Engage two locking latches

6. Put pulp container onto main housing

When probably placing lid on pulp collector, there will be a gap
of about 9 mm between lid and pulp collector on the switch side.
This is normal.

When pressing lid to close, a rib on lid will press onto a linkage
pin in pulp collector, which in turn press onto another linkage
pin (integrated with cover plate) on main housing. This then
moves down the cover plate and exposes the safety micro­switch. Upon engaging locking latch, the safety micro-switch is
activated by a pin on the locking latch and the appliance can be
switched on.
If pulp collector and lid are not probably assembled, the cover
plate will prevent the activation of safety micro-switch.

Test the safety micro-switch by engaging and disengaging the
locking latch on switch side.

The drive coupling is screwed onto the motor shaft by means of
a right-handed thread.

The drive coupling can be disconnected from the motor shaft by
blocking a slot in motor shaft, which is accessible through a slot
on bottom cover.

After the product has been repaired, it should
function properly and has to meet the safety
requirements as offi cially laid down at this
moment.

Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification

4322 277 01073
02/10

PARTS LIST

HR1821/A / HR1821/B

Pos Service code Description

9965 000 11070

1

9965 000 11770

2

9965 000 15545
4822 480 10235

3

9965 000 11771

4

9965 000 15546
9965 000 11772

5

9965 000 15547

4822 528 11285

6

9965 000 11773

7

9965 000 15548
9965 000 11774

8

9965 000 11775

9

9965 000 11776

10

9965 000 11777

11

9965 000 11778

12

9965 000 11779

13

9965 000 11780

14

9965 000 11781

15

Pusher
Lid (incl. insert) /A
Lid (incl. insert) /B
Sieve
Pulp collector complete /A
Pulp collector complete /B
Juice spout /A
Juice spout /B

Coupling
Main housing /A
Main housing /B
Locking latch on switch side
Hinge
Locking latch on back side

Bottom cover complete
Switch bracket
Micro switch
Cover plate
Switch

Pos Service code Description

16

9965 000 11782
9965 000 15549
9965 000 15537

17

9965 000 15538
9965 000 11783
9965 000 15539

18

9965 000 15550

9965 000 15540

19

9965 000 15541
9965 000 15542
9965 000 11785
9965 000 15543
9965 000 11787

20

9965 000 15551

9965 000 11786

21

9965 000 15544

22

9965 000 01057

23

Switch cap /A
Switch cap /B
Motor 110 V (with RFI)
Motor 120-127 V (without RFI)
Motor 220-240 V (with RFI)
Pulp container detachable /A
(also suitable for older versions)
Pulp container detachable /B

Power cord - Mexico
Power cord - Argentina
Power cord - Hong Kong
Power cord - PRC
Power cord - General
Juice cup incl. lid /A
Juice cup incl. lid /B

Vibration rubber
Capacitor 0,22 µF
Capacitor 0,10 µF

AC

110V

R.H.

Chock

8.5µH

NC

C

Main

switch

110 V with RFI Circuit diagram 120-127 V without RFI Circuit diagram

NO

C22

0.22µF

R.H.

Chock

Motor

Main

switch

35µH

35µH

Main

switch

A

C

AC

120-127 V

NC

Motor

NO

15µH

NC

C

NO

Motor

A

AC

220V

8.5µH
C23

0.1µF

220 V with RFI Circuit diagram

A

15µH

2-3