Philips HR1564AB Service Manual

Cucina Stand and Bowl Mixer

HR1564/AB
RI7110/AB

Philips Domestic Appliances and Personal Care

Service Manual

PRODUCT INFORMATION

- HR1564/AB - RI7110/AB :

5 speed mixer + turbo + non driven stand & bowl

- Materials used / Colours

Mixer housing PP White
Beater ejector PS Zinc Brown
Speed selector ABS Pearl blue
Bowl (3,5 L ) PP White
Stand housing PP White
Beaters Chrome plated steel Metal
Cord clip PP White

- After the product has been repaired, it should function
properly and has to meet the safety requirements as
officially laid down at this moment.

TECHNICAL INFORMATION

- High Voltage : 220 - 240 V, 50 - 60 Hz

- Low Voltage : 110 - 127 V, 50 - 60 Hz

- Power consumption : 300 W

- Dimensions : 340 x 240 x 370 mm

- Weight appliance
incl. Stand and bowl : 2000 gr

- Motor : Series wound, Statically and
dynamically balanced
Self lubricated

- Transmission ratio
between rotor spindle
and gearwheel : 21½ : 1

- Cordlength : 1,4 m double insulated with
molded on plug

- Speeds beaters unloaded : Switch position 1 - 650 rpm
Switch position 2 - 750 rpm
Switch position 3 - 850 rpm
Switch position 4 - 950 rpm
Switch position 5 - 1050 rpm
Turbo position - 1050 rpm

DISASSEMBLY- AND RE-ASSEMBLY ADVISE

- Use the blade of a knife to remove the hinged arm from the
stand. Insert the blade between the arm and the lower part
of the stand in such a way that the hinge located at triangle
(1) can be pushed inwards and the arm (2) can be pulled
upwards and out of the lower part of the stand.

- Reassemble the arm by placing it horizontally back into the
lower part of the stand, making sure the V-shaped groove
of the hinge fits round the guide rib in the lower part of the
stand.

2

1

1

Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification

03/02

HR1564/AB
RI7110/AB

Circuit diagram 220 - 240 VCircuit diagram 115 - 127 V

0

T

Motor assy

2

1

3

4

5

Red GrayBlackGreen

Rotor

MAINS

REPAIR INSTRUCTION

Mounting gearwheels

When mounting the gearwheels make sure that the cams of
the gearwheels are situated at the front of the beaters.

The angle between the beaters must be 45°.
So when carrying out a repair be sure that the gearwheels are

mounted correctly (see Fig. 1).

90

˚

45

˚

Fig. 1

Lubrication

Use graphite grease code no. 4822 390 20004 to grease the
appliance on the following points:

1. Spaces between the teeth of the wormwheels.

2. Both sides of the wormwheel shaft.

Motor

The motor cannot operate properly, when, due to
contamination, carbon brush is unable to move freely in
guide bush and consequently cannot be pressed against the
commutator.

0

T

Motor assy

2

1

3

4

5

Red GrayBlackYellow

Rotor

MAINS

PARTS LIST

Pos Description Service code

1

Housing set - HR1564/AB
Housing set - RI7110/AB

2

Switch assy ( 220 V )
Switch assy ( 110 V )

3

Ejector

4

Ejector spring

5

Cord set – Mexico
Cord set – EU
Cord set – ARG
Cord set – Brazil

6

Cord clip

7

Cord grommet

8

Bearing plate

9

Strip beaters in pair

11

Motor buffer

12

Driven gearwheel

13

Arm without sieve assy

14

Stand assy

15

Rubber stud

17

Bowl 3,5 L

A

Screw 2,9 x 13

4206 136 54240
4206 136 54260
4206 136 55200
4206 136 53770
4206 133 94630

4206 132 07960
4206 100 02240
4206 100 02230
4206 100 02220
4206 100 02210

4206 133 86150
4206 133 53720
4206 133 94650
4206 136 54190
4206 133 53120

4206 133 82320
4206 136 55290
4206 136 54630
4206 133 53300
4206 133 94740

OPTIONAL (accessories)

- No specific issues.

2-3