Philips HQ6893A Service Manual
Service
Service
Shaver
HQ 6893/A
Service
Service
Information
!
Domestic Appliances and Personal Care
HINTS FOR REPAIRS
-
Remove the shaving unit, to prevent damages
during repairs.
-
Remove screws A1 (2x, of which 1 is under
trimmer slide).
-
Take cover with trimmer from housing.
-
Remove bracket (14 + 21).
-
The PC-board can now be removed from the
housing.
-
Remove screws B1 (2x) the motor and hairchamber can now be removed from the housing.
-
Detach the motor clamping spings (item 17)
on the bearing block with a small screwdriver.
GENERAL
• Mainsshaver possible.
• Converts input voltage 8-16V dc to constant
Charge current (NiHH 1100mA, NiCD 680mA)
or Constant motorvoltage at mainsshave.
Start-up voltage min. 11V.
• Open battery protection.
• Undervoltage protection.
• Temperature protection of battery (only NiMH).
• Charge condition of battery is managed by
microcontroller. Charge current is regulated and
discharge currents is measured.
• Charge condition of battery shown on LCD display
(minutes left) with backlighting. Full indication
with flashing (2Hz) of backlighting.
• Electronic on/off.
QUADRA ACTION
TECHNICAL DATA
Voltage
Power consumption
Motor voltage
Power supply
Speed of cutters
Shaving heads
Battery
SAP CODING: 8856 893 99999
CAUTION!
WHILE CHECKING THE P.C.-BOARD REMEMBER
THAT MOST COMPONENTS AND MOTOR ARE
ENERGIZED BY MAINS VOLTAGE.
:
100-240 V 50/60Hz
:
Motor depending
:
2.4 V
:
SMPS
:
> 2100 r.p.m.
:
HQ6 - 4822 690 10214
:
Green NiMH pack AA
PRODUCTS MEETS THE REQUIREMENTS REGARDING
INTERFERENCE SUPPRESION ON RADIO AND TELEVISION.
- AFTER THE PRODUCT HAS BEEN REPAIRED IT SHOULD
FUNCTION PROPERLY AND HAS TO MEET THE SAFETY
REQUIREMENTS AS LAID DOWN OFFICIALLY ESTABLISHED
AT THIS MOMENT.
Published by Philips Domestic Appliances and Personal Care Printed in The Netherlands Copyright reserved Subject to modification
©
4322 277 00146
99/12
PCS 104 743
HQ 6893/A
2625
5
19
6
1
2
7
20
21
8
22
9
10
NiMH
23
B1
11
12
3
4
1 4822 479 20261 cleaning brush
2 4222 036 01220 housing PH
3 4822 466 12232 rubber seal
4 4822 219 10711 power plug EU
4822 219 10715 power plug GB
5 4822 462 11177 protecting cap
6 4822 441 12327 head housing
7 4822 690 10214 HQ6 shaving head
8 4822 214 13061 power module
9 4822 402 11319 retaining bracket
10 4222 036 01020 hairchamber PH
11 4822 265 11548 connecting pins
12 4822 522 10762 gearwheel unit
13 4822 466 12233 sealing plate
14 4822 402 11318 bracket small
13
14
15
16
17
18
15 4822 522 10763 pinion
16 4822 361 21783 motor
17 4822 492 71735 motor clamp
18 4822 130 34167 Zener diode
19 4222 036 01200 trimmer
20 4222 036 01210 trimmer slide
21 4822 402 11317 bracket large
22 4822 532 13149 spacer AA
23 4822 138 10728 NiMH pack AA
24 4222 036 01190 cover
25 4822 135 00282 LCD complete
26 4822 256 10572 holder
A 4822 502 14657 s.t.screw spec/T8
B 4822 502 14544 s.t.screw 1.8x18/T8
4822 600 10861 pouch PH
24
A1
4822 462 11183 stand
4822 736 16936 DFU (1)
4822 736 16937 DFU (2)
(1) GB D F NL E P I TR
(2) GB D N S FIN DK GR
* 4222 036 01960 Car cord
PCS 104 734
Loading...