Philips HQ6832A Service Manual

Rechargeable shaver

HQ6832/A

QUADRA ACTION

Service
Information

!

Philips Domestic Appliances and Personal Care

Service Manual

Mains

R1

D4

C1 C2

R5

C4

R6

R4

Power plug

Power module

L1

IC3

1

SRC

2

VAUX

GND

3

CBT

4

RREF

DRN

GND

D3

T1

C7

C8

D1

D2

8

5

7

NC

6

D6

D5

R2

C6

C3

C5

TIPS FOR REPAIR

- Remove the shaving unit to prevent damage during repair.

- Remove screws A1 (2x, of which 1 is under trimmer slide).

- After the cover (item 27) has been removed, it must be
checked if the rubber seal (item 3) has not been damaged.

- The cover contains a sticker that is permeable to gas yet
impermeable to water.
This sticker may nor be removed under any circumstances.

- Remove the metal brackets.

- Unsolder the motor connector and remove the PCB.

- To replace the motor (item 20) or the driving unit (item 16),
screws B1 must be removed fi rst.

- Then push the entire unit out of the housing (item 2) and
check if its sealing is damaged.

- Detach the motor clamping springs (item 21) with a small
screwdriver.

- The entire driving unit (item 16) is supplied as a single part

D1

R3

R18

IC2a

14

5

6

7

SK1

C5C4 C6

C10

TS6a

R32

D5

R31R35

R30R34

4

TS6b

R19

R20

R21

R29

C11

2

3

IC2b

R25

R27

R26

1

IC2c

8

9

R22 R23

R33

TS7

R39

R40

C7

IC2d

11

C8

R4R1

R41

TS1

D4a D4b

13

R5

C2

D3

10

12

R3

R2R28

TS5

R17

C9

R13

R14

D6

R15R6

IC1

68

VCC

TH

2

TR

5

CV

R7

3

Q

4

R

R8

7

1

DIS

GND

R36

TS9

D43

R24

TS8

R11

TS3

R38

MF2

PM

L3

TS2

TS4

R10R12R37

A

C3

NiMH

2 x AA

R9

L1

D2

MF1

C1

R16

TECHNICAL DATA

Input voltage : 100-240 V, 50/60 Hz
Power consumption : max. 7 W
Motor voltage : 2.4 V
Battery : 2x NiMH AA
Battery capacity : approx. 1100 mAh
Charging indicator : 1x LED green - charge
Charging time : approx. 1 hour
: initial 4 hours
Charging current : 1100/40 mA temp. dependent
Power supply : HQ6000 external transformer
: HQ6010 car cord
Shaving heads : HQ6 - 4822 690 10214
Cleaning : wet / dry
Comfort control : fi xed setting
: 3-D contour following
Mains shaving : yes

to guarantee optimal sealing of the gear shafts.

- To guarantee that the shaver is completely watertight, only

SAP CODING : HQ6832

the original screws may be used.

- To charge the shaver only the original HQ6000 power plug
may be used.

Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification

4322 277 00593
02/12

HQ6832/A

If the HQ6832/A shaver is supplied with a HQ8000 powerplug, remove R35 from the PCB.

Removing R35 will not adversely affect the shaver’s performance.

If the shaver has been supplied with a HQ8000 plug, R35 and its surrounding will look burned. See picture.

If the customer complaint can be related to battery capacity, also replace the battery.