Philips HQ6756A Service Manual

Rechargeable shaver

HQ 6756/A

CoolSkin

Service
Information

!

Philips Domestic Appliances and Personal Care

Service Manual

D6

R22

C5

C3

17

VBL1

VBR

R17

R16

R19 R18

L2

R25

216

15 14 9 10

VAC

UPC

NOD

IC2

TACC18NCEL

RRET

19

R20

R21

C4

D4a D4b

VCC

FULL

CTIM

DUTY13GND

20 11 3

C6

C7

EMP

EOO

SK1

Mains

R1

D4

C1 C2

R5

C4

R6

R4

Power plug

Power module

D3

L1

1

SRC

2

GND

3

CBT

4

RREF

T1

C7

D1

D2

IC3

DRN

VAUX

NC

GND

D5

R2

8

5

7

C3

6

R3

C8

D6

C6

C5

D1

R1

TS3

TS4

R1

R2

R6R4

R28

R3

TS1

R26

R23

D3

TS5

R5

4

5

C2

TIPS FOR REPAIR

- Remove the shaving unit to prevent damage during repair.

- Remove the outer cover (item 27) and cartridge (item 28).

- Remove 5 A1 screws.

- After the cover (item 16) has been removed, it must be
checked if its sealing has not been damaged.

- The cover (item 16) contains a sticker that is permeable
to gas yet impermeable to water.
This sticker may not be removed under any circumstances.

- Unsolder the motor connector and remove the PCB.

- To replace the motor (item 10) or the driving unit
(item 6), screws B1 must be removed fi rst.
Then push the entire unit out of the housing (item 12) and
check if its sealing is damaged.

- The entire driving unit (item 6) is supplied as a single part
to guarantee optimal sealing of the gear shafts.

VCC

R

CV

A
NiCd
2 x AA

D2

L1

C9

IC1

G
TH
TR

OIS

GND

C1

R7

38
6

R24

2

R8

7
1

MF1

R10

TS2

R9

R11

R12

MF2

PM

D43

C8

5

DIS

4

SMOT

R13

1

MAINS

R14

12

RREG

TAMB

876

TECHNICAL DATA

Input voltage : 100-240 V, 50/60 Hz
Power consumption : max. 7 W
Motor voltage : 2.4 V
Battery : 2x NiCd AA
Battery capacity : approx. 700 mAh
Charging indicator : 1x duoLED green / red
: charge - full / battery low
Charging time : approx. 1 hour
Charging current : 1000/40 mA temp. dependent
Charging device : HQ600 external transformer
Shaving heads : HQ167 - 4222 036 04250
Shaving emulsion : HQ160 shaving emulsion
: HQ161 fresh gel
Mains shaving : no

SAP CODING : HQ6756

- A replacement of the pump button (item 22) is only
possible after removal of the hair chamber (item 5).

- To guarantee that the shaver is completely watertight, only
the original screws may be used.

- To charge the shaver only the original HQ600 power plug
may be used.

Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification

4322 277 00587
01/04

HQ 6756/A

1 12

2

3

4

5

13

14

15

22

B1

23

24

25

NiCd

26

6

7

16

8
9

10

11

1 4222 036 04140 protecting cap
2 4222 036 04260 head housing
3 4222 036 04250 HQ167 shaving head
4 4222 036 04270 retaining bracket
5 4222 036 04240 hair chamber

6 4222 036 04200 gearwheel unit
7 4222 036 04210 sealing plate
8 4822 522 10763 pinion
9 4822 492 71735 motor clamp
10 4822 361 21783 motor 2.4V

11 4822 479 30183 cleaning brush
12 4222 036 04160 housing
13 4222 036 04300 power module
14 4822 265 11548 connector
15 4822 256 10454 holder

16 4222 036 04180 cover
17 4222 036 04190 release knob
18 4222 036 04100 stand
19 4822 130 34167 Zener diode
20 4222 036 01150 motor connector

17

18

19
20

21

A1

27

28

29
30

C1

21 4222 036 04130 hanging cord
22 4222 036 04170 pump button
23 4222 036 04110 trimmer
24 4222 036 04220 battery holder
25 4822 138 10334 NiCd pack AA

26 4822 360 10389 pump
27 4222 036 04150 outer cover
28 4222 036 04400 HQ160 shaving emulsion
4222 036 04410 HQ161 fresh gel
29 4222 036 04060 straight fl ex

30 4222 036 04080 power plug EU
4222 036 04850 power plug ROK
A 4822 502 14545 s.t.screw spec.
B 4822 502 14544 s.t.screw 1.8x18/T8
C 4822 502 30526 s.t.screw 1.8x10/T8

4222 036 04120 case