Rechargeable shaver
HQ 673/A
CoolSkin
Philips Domestic Appliances and Personal Care
Service Manual
T1
Mains
Power plug
Power module
D
C
RR
TIPS FOR REPAIR
- Remove the shaving unit to prevent damage during repair.
- Remove the slide cover (item 21) and cartridge (item 20).
- Push the edge of the hair chamber up with your thumb
until the snap connection unlocks (see ‘X’ in exploded
view).
- Remove 3 A1 screws.
- Remove the cover (item 14).
- Use a screwdriver to push the connecting plate (item 17)
up at a connecting strip (‘Z’ in exploded view).
- Tilt the motor slightly to detach the snap hooks of the hair
chamber.
- Lift the motor and the PCB out of the housing.
- The cover (item 14) contains a sticker that is permeable to
gas yet impermeable to water.
- This sticker may not be removed under any circumstances.
D1a D1b
D3
D4
R2
D2a
TS3
C3
C1
L1
TS4
R5
R23
216 17415 14 10
MOO
TACC
C24C23
VBR
VAC
R24
VBLI
TAMB
SMOT
GND
138201918376
C25
TS21
D43
MF2
PM
A
NiCd
AA
L21
D21
C22
D2b
IC21
C2
EOO UPC
SK1
VCC
NCEL
EMP
REFF
R22R21
CTIM
C21
R6
R1
TS1
TS2
R3
R4
TECHNICAL DATA
Input voltage : 100-240 V, 50/60 Hz
Power consumption : max. 9 W
Motor voltage : 1.2 V
Battery : 1x NiCd AA
Battery capacity : approx. 700 mAh
Charging indicator : 1x duoLED green / red
: charge / battery low
Charging time : approx. 8 hours
Charging current : 0.2 C continuous
Charging device : HQ 600 external transformer
Shaving heads : HQ 167 - 4222 036 04250
Shaving emulsion : HQ 160 shaving emulsion
: HQ 161 fresh gel
Mains shaving : no
SAP CODING : HQ 673
- The entire drive unit (item 10) is supplied as a single part
to guarantee optimal sealing of the gear shafts.
- When reassembling the shaver, the sealing ring (item 2)
must be placed onto the housing.
- To guarantee that the shaver is completely watertight, only
the original screws may be used.
- A new sealing ring must be used to ensure a proper
sealing of the shaver.
Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification
4322 277 00485
01/02
HQ 673/A
18
1
5
19
6
20
7
2
3
8
A1
X
X
21
9
14
4
1 4822 479 20198 cleaning brush
2 4822 532 13111 sealing ring
3 4222 036 04830 housing PH
4 4222 036 03690 power plug EU
4222 036 03750 power plug GB/SA
5 4222 036 04720 protecting cap
6 4222 036 04840 head housing
7 4222 036 04250 HQ167 shaving head
8 4822 402 11251 retaining bracket
9 4222 036 04730 hairchamber
15
Y
16
10
11
NiCd
22
23
24
25
12
13
17
26
Z
15 4222 036 04780 release knob
16 4222 036 04810 power module
17 4822 265 11548 connector
18 4222 036 04800 trimmer
19 4822 360 10389 pump
20 4222 036 04400 HQ160 shaving emulsion
4222 036 04410 HQ161 shaving gel
21 4222 036 04770 slide cover
22 4822 130 34167 Zener diode
23 4222 036 01150 motor connector
10 4822 522 10747 gearwheel unit
11 4822 522 10748 pinion
12 4822 361 21752 motor 1.2V
13 4822 492 63165 motor clamp
14 4222 036 04820 cover PH
24 4822 466 12153 foam plate 1 mm
25 4822 466 12155 foam plate 4 mm
26 4822 138 10633 NiCd cell AA
A1 4822 502 14545 s.t.screw spec.
4222 036 04700 case
4222 036 04710 pouch