Philips HQ360A Service Manual

Service

Service

Service

Domestic Appliances and Personal Care

Rechargeable shaver ”Marco Polo”

HQ 360/A

SAP Coding HQ 360

TECHNICAL DESCRIPTION

The HQ360 shaver can be recharged in 8 hours by
means of a ’Swiched Mode Power Supply’.
The heart of the power supply consists of IC1,
incorporating the following functions:
a. a current controller to adjust the charge current,
b. a primary current limiter to protect the transformer
from saturation.
c. a frequency limiter.
d. an open cell protection.
e. a chip temperature protection.

The green LED only illuminates when the shaver is
connected to the mains.

HINTS FOR REPAIRS

- Remove the shaving unit, to prevent damages
during repairs.

- Remove screw A (1x).

- Put the shaver on the table and remove the tailpart
(item 15) from the shaver.
Lift the PCB with motor out of the housing.

- Loosen the motor clampings springs (item 18) on the
bearing block with a small screwdriver.

- Unlock peg clamping ’Z’ (2x) between frame (item 16)
and hair chamber (item 11).

R1

D1

L1

C1

C2

1311

1

1

10

16

IC1

8

C4

C4

C5

12

96

14
13

4

T1

D1

D2

R4

R2D4

C3

D5

R3

SK1

TECHNICAL DATA

Voltage : 100-240V, 50/50 Hz
via slide pins
Motor voltage : 1.2 V
Cell : Nicd AA
Cell capacity : approx. 700 mAH
Charging system : SMPS
Charge indicator : green LED
Charging time : approx. 8H
Charging current : approx. 100 mA
Shaving heads : 2xHQ3
Comfort control : fixed setting

NiCd

A

D9

PRODUCTS MEETS THE REQUIREMENTS REGARDING
INTERFERENCE SUPPRESION ON RADIO AND TELEVISION.

- AFTER THE PRODUCT HAS BEEN REPAIRED IT SHOULD
FUNCTION PROPERLY AND HAS TO MEET THE SAFETY
REQUIREMENTS AS LAID DOWN OFFICIALLY ESTABLISHED
AT THIS MOMENT.

Published by Philips Domestic Appliances and Personal Care Printed in The Netherlands Copyright reserved Subject to modification

©

4322 277 00112

02/09

HQ 360/A

1

2

3
4

5

6

10

Z

7
8

11

12

A1

1.8x10/T8

NiCd

13

14

17

9

15

16

18
19

20

1 4222 036 01330 Protection cap
2 4222 036 01340 Head housing
3 4222 036 02770 Cleaning brush
4 4822 690 30471 HQ3 shaving head
5 4222 036 02780 Head holder

6 4222 036 01550 Hairchamber
7 4222 036 01560 Gearwheel
8 4222 036 01300 On/off knob
9 4222 036 01660 Housing

10 4222 036 01680 Cover
11 4222 036 03090 Power module 220V PRC

12 4222 036 01420 Frame
13 4822 522 33547 Pinion
14 4822 361 21752 Motor 1.2V
15 4822 492 63165 Motor clamp

16 4822 130 34167 Zener diode
17 4822 466 91312 Foam plate
18 4822 138 10633 NiCd cell AA
19 4222 036 01670 Contact plate
20 4222 036 01610 Plug pins

A 4822 502 30526 s.t. screw 1.8x10/T8