HD8752-87
Register your product and get support at
www.philips.com/welcome
02
English
Type HD8752
USER MANUAL
EN
02
PLEASE READ THIS USER MANUAL CAREFULLY BEFORE USING THE MACHINE.
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
followed, including the following:
1. Read all instructions.
2. Do not touch hot surfaces. Use handles or knobs.
3. To protect against fire, electric shock and injury to persons do not immerse
cord, plugs, or appliance in water or other liquid.
4. Close supervision is necessary when the appliance is used by or near
children.
5. Unplug from outlet when not in use and before cleaning. Allow to cool
before putting on or taking off parts, and before cleaning the appliance.
6. Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions, or has been damaged in any manner. Return
appliance to the nearest authorized service facility for examination, repair
or adjustment.
7. The use of accessory attachments not recommended by the appliance
manufacturer may result in fire, electric shock or injury to persons.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or counter, or touch hot surfaces.
10. Do not place on or near a hot gas or electric burner, or in a heated oven.
11. Always attach plug to appliance first, then plug cord into wall outlet. To
disconnect, turn any control to “off”, then remove plug from wall outlet.
12. Do not use appliance for other than intended use.
13. Save these instructions.
SAVE THESE INSTRUCTIONS
CAUTION
This appliance is for household use only. Any servicing, other than cleaning
and user maintenance, should be performed by an authorized service center.
Do not immerse machine in water. To reduce the risk of fire or electric shock,
do not disassemble the machine. There are no parts inside the machine
serviceable by the user. Repair should be done by authorized service personnel
only.
1. Check voltage to be sure that the voltage indicated on the nameplate
corresponds with your voltage.
2. Never use warm or hot water to fill the water tank. Use cold water only.
3. Keep your hands and the cord away from hot parts of the appliance during
operation.
4. Never clean with scrubbing powders or harsh cleaners. Simply use a soft
cloth dampened with water.
5. For optimal taste of your coffee, use purified or bottled water. Periodic
descaling is still recommended every 2-3 months.
6. Do not use caramelized or flavored coffee beans.
INSTRUCTIONS FOR THE POWER
SUPPLY CORD
A. A short power-supply cord (or detachable power-supply cord) is to be
provided to reduce risks resulting from becoming entangled in or tripping
over a longer cord.
B. Longer detachable power-supply cords or extension cords are available
and may used if care is exercised in their use.
C. If a long detachable power-supply cord or extension cord is used,
1. The marked electrical rating of the detachable power-supply cord or
extension cord should be at least as great as the electrical rating of the
appliance
2. If the appliance is of the grounded type, the extension cord should be a
grounding-type 3-wire cord, and
3. The longer cord should be arranged so that it will not drape over the
counter top or table top where it can be pulled on by children or tripped
over.
2
ENGLISH
Congratulations on your purchase of a Saeco Intelia Class
fully automatic co ee machine!
To fully bene t from the support that Saeco o ers, please
register your product at www.philips.com/welcome.
This user manual applies to HD8752.
The machine is made for preparing espresso co ee using
whole co ee beans and for dispensing steam and hot water.
In this user manual you will nd all the information you need
to install, use, clean and descale your machine.
ENGLISH
CONTENTS
IMPORTANT..................................................................................................... 4
Safety Instructions ....................................................................................................................................4
Warning ....................................................................................................................................................4
Cautions ....................................................................................................................................................6
Compliance with Standards ...................................................................................................................... 7
INSTALLATION ................................................................................................. 8
Product Overview ......................................................................................................................................8
General Description ...................................................................................................................................9
PREPARING FOR USE .......................................................................................10
Machine Packaging .................................................................................................................................10
Machine Installation ...............................................................................................................................10
USING THE MACHINE FOR THE FIRST TIME ........................................................12
Circuit Priming ........................................................................................................................................12
Automatic Rinse/Self-Cleaning Cycle.......................................................................................................13
Manual Rinse Cycle..................................................................................................................................14
Measuring and Programming Water Hardness ........................................................................................16
“INTENZA+” Water Filter Installation ...................................................................................................... 17
Replacing the “INTENZA+” Water Filter ...................................................................................................19
ADJUSTMENTS ................................................................................................20
Saeco Adapting System ........................................................................................................................... 20
Adjusting the Ceramic Co ee Grinder ..................................................................................................... 20
Adjusting the Aroma (Co ee Strength) ...................................................................................................21
Adjusting the Dispensing Spout ..............................................................................................................22
Adjusting the Co ee Length ...................................................................................................................23
ESPRESSO AND COFFEE BREWING ....................................................................24
Espresso and Co ee Brewing Using Co ee Beans ....................................................................................24
Espresso and Co ee Brewing Using Pre-Ground Co ee ...........................................................................25
CAPPUCCINO BREWING ...................................................................................26
HOT WATER DISPENSING .................................................................................28
CLEANING AND MAINTENANCE ........................................................................30
Daily Cleaning of the Machine. ................................................................................................................30
Daily Cleaning of the Water Tank .............................................................................................................31
Daily Cleaning of the Automatic Milk Frother .......................................................................................... 31
Weekly Cleaning of the Machine .............................................................................................................32
Weekly Cleaning of the Brew Group ........................................................................................................33
Monthly Cleaning of the Automatic Milk Frother.....................................................................................35
Monthly Lubrication of the Brew Group ..................................................................................................40
Monthly Cleaning of the Brew Group with “Co ee Oil Remover” ............................................................. 41
Monthly Cleaning of the Co ee Bean Hopper .......................................................................................... 43
DESCALING .....................................................................................................44
PROGRAMMING ..............................................................................................48
Adjustable Parameters ............................................................................................................................48
Programming Example ...........................................................................................................................49
MEANING OF THE DISPLAY ICONS .....................................................................51
TROUBLESHOOTING ........................................................................................54
ENERGY SAVING ..............................................................................................56
Stand-by .................................................................................................................................................56
Disposal .................................................................................................................................................. 56
TECHNICAL SPECIFICATIONS ............................................................................57
WARRANTY AND SERVICE ................................................................................57
Warranty .................................................................................................................................................57
Service .................................................................................................................................................... 57
ORDERING MAINTENANCE PRODUCTS ..............................................................58
3
4
ENGLISH
IMPORTANT
Safety Instructions
This machine is equipped with safety features. Nevertheless
read the safety instructions carefully and only use the machine as described in these instructions to avoid accidental
injury or damage.
Keep this user manual for future reference.
The term WARNING and this icon warn against possible
severe injuries, danger to life and/or damage to the machine.
The term CAUTION and this icon warn against slight
injuries and/or damage to the machine.
Warning
• Connect the machine to a wall socket with a voltage
matching the technical speci cations of the machine.
• Do not let the power cord hang over the edge of a table or
counter, or touch hot surfaces.
• Never immerse the machine, mains plug or power cord in
water (danger of electrical shock!).
• Never direct the hot water jet towards body parts: danger
of burning!
• Do not touch hot surfaces. Use handles and knobs.
• Remove the mains plug from the wall socket:
- If a malfunction occurs.
- If the machine will not be used for a long time.
- Before cleaning the machine.
ENGLISH
Pull on the plug, not on the power cord. Do not touch the
mains plug with wet hands.
• Do not use the machine if the mains plug, the power cord
or the machine itself is damaged.
• Do not make any modi cations to the machine or its
power cord. Only have repairs carried out by a service
centre authorised by Philips to avoid a hazard.
• The machine should not be used by children younger than
8 years old.
• The machine can be used by children of 8 years and
upwards if they have previously been instructed on the
correct use of the machine and made aware of the associated dangers or if they are supervised by an adult.
• Cleaning and maintenance should not be carried out by
children unless they are more than 8 years old and supervised by an adult.
5
5
• Keep the machine and its power cord out of reach of children under 8 years old.
• The machine may be used by persons with reduced physical, sensory or mental capabilities or lacking su cient
experience and/or skills if they have previously been
instructed on the correct use of the machine and made
aware of the associated dangers or if they are supervised
by an adult.
• Children should be supervised to ensure that they do not
play with the machine.
• Never insert ngers or other objects into the co ee
grinder.
6
ENGLISH
Cautions
• The machine is for household use only. It is not intended
for use in environments such as canteens, shop sta kitchens, o ces, farms or other work environments.
• Always put the machine on a at and stable surface.
• Do not place the machine on hot surfaces, directly next to
a hot oven, heater units or similar sources of heat.
• Only put co ee beans into the co ee bean hopper. If
ground co ee, instant co ee or any other substance is put
in the co ee bean hopper, it may damage the machine.
• Let the machine cool down before inserting or removing
any parts.
• Never use warm or hot water to ll the water tank. Use
cold water only.
• Never clean with scrubbing powders or harsh cleaners.
Simply use a soft cloth dampened with water.
• Descale your machine regularly. The machine indicates
when descaling is needed. Not doing this will make your
appliance stop working properly. In this case repair is not
covered under your warranty!
• Do not keep the machine at temperature below 0 °C.
Residue water in the heating system may freeze and cause
damage.
• Do not leave water in the water tank when the machine
is not used over a long period of time. The water can be
contaminated. Use fresh water every time you use the
machine.
ENGLISH
Compliance with Standards
The machine complies with art.13 of the Italian Legislative
Decree dated 25 July 2005, no. 151 “Implementation of the
Directives 2005/95/EC, 2002/96/EC and 2003/108/EC on the
restriction of the use of certain hazardous substances in electrical and electronic equipment, as well as waste disposal”.
This machine complies with EU Directive 2002/96/EC.
This Philips appliance complies with all the applicable standards and regulations relating to the exposure to electromagnetic elds.
7
7
8
INSTALLATION
Product Overview
12 34
5
6
7
8
13
20
9
10 11 22 12
30
14
18 19
24
25
26
15
16
23
31
17
27
28
29
21
ENGLISH
General Description
1. Grinder adjustment knob
2. Pre-ground co ee compartment
3. Co ee bean hopper
4. Co ee bean hopper lid
5. Control panel
6. Co ee dispensing spout
7. Cup holder grill
8. Full drip tray indicator
9. Drip tray
10. Co ee grounds drawer
11. Brew group
12. Service door
13. Grease for the brew group
14. Power cord
15. Automatic Milk Frother
16. Suction tube
17. Water tank
18. Power cord socket
19. Power button
20. Co ee grinder adjustment key + Pre-ground co ee measuring scoop
21. Cleaning brush - to be purchased separately
22. Co ee residues drawer
23. Water hardness test strip
24. Espresso brew button
25. Co ee brew button
26. Hot water/steamselection button
27. ON/OFF button
28. "Aroma" - Pre-ground co ee button
29. "MENU" button
30. Descaling solution- to be purchased separately
31. Steam wand + rubber grip for Automatic Milk Frother
9
9
10
ENGLISH
PREPARING FOR USE
Machine Packaging
The original packaging has been designed and constructed to protect the
machine during transport. We recommend keeping the packaging material
for possible future transport.
Machine Installation
Remove the drip tray with grill from the packaging.
1
Remove the machine from the packaging.
2
For best use, it is recommended to:
3
• Choose a safe, level surface, where there will be no danger of overturning the machine or being injured.
• Choose a location that is su ciently well-lit, clean and near an easily reachable socket.
• Allow for a minimum distance from the sides of the machine as
shown in the illustration.
Insert the drip tray with grill into the machine. Make sure it is fully
4
inserted.
Note:
The drip tray collects the water that comes out of the dispensing spout
during each rinse/self-cleaning cycle, as well as co ee that might be spilled
during beverage preparation. Empty and wash the drip tray daily and each
time the full drip tray indicator is raised.
Caution:
NEVER remove the drip tray when the machine has just been turned
on. Wait a couple of minutes for the machine to carry out a rinse/selfcleaning cycle.
11
11
Remove the water tank.
5
ENGLISH
1
2
Rinse the water tank with fresh water.
6
Fill the water tank with fresh water up to the MAX level and reinsert it
7
into the machine. Make sure it is fully inserted.
Caution:
Never ll the water tank with warm, hot, sparkling water or any other
liquid, as this may cause damage to the water tank and the machine.
Remove the co ee bean hopper lid and slowly pour the co ee beans
8
into the co ee bean hopper.
Note:
Do not pour too many co ee beans into the co ee bean hopper as this will
reduce the grinding performance of the machine.
Caution:
Only co ee beans must be put into the co ee bean hopper. Ground
co ee, instant co ee, caramelized co ee or any other object may
damage the machine.
Put the lid on the co ee bean hopper.
9
Insert the plug into the socket located on the back of the machine.
10
1
Insert the plug at the other end of the power cord into a wall socket
11
with suitable power voltage.
2
12
ENGLISH
Switch the power button to “I” to turn on the machine. The display
12
shows the stand-by icon.
BlackYellow
To turn on the machine simply press the “ ” button. The display indi-
13
cates that the circuit must be primed.
USING THE MACHINE FOR THE FIRST TIME
When using the machine for the rst time, the following activities need to
happen:
1) You need to prime the circuit;
2) The machine will perform an automatic rinse/ self-cleaning cycle;
3) You need to initiate a manual rinse cycle.
Circuit Priming
During this process fresh water ows through the internal circuit of the
machine and the machine warms up. This takes a few minutes.
Place a container under the steam wand.
1
Press the “ ” button to start the cycle. The machine starts the auto-
2
matic priming of the circuit by dispensing some water through the
steam wand.
The bar under the icon shows the operation progress. When the pro-
3
cess is completed, the machine stops dispensing automatically.
Yellow
Then the display shows the machine warm-up icon.
4
Yellow
Automatic Rinse/Self-Cleaning Cycle
When warm-up is completed, the machine automatically performs a rinse/
self- cleaning cycle of the internal circuit with fresh water. This takes less
than a minute.
ENGLISH
13
13
Place a container under the co ee dispensing spout to catch the small
5
amount of water which will be dispensed.
The machine shows this display. Wait for the cycle to nish automati-
6
cally.
Yellow
Note:
You can stop dispensing by pressing the “
When the above steps are complete, the machine shows this display.
7
Green
” button.
14
ENGLISH
Manual Rinse Cycle
During this process you activate the co ee brewing cycle and fresh water
ows through the steam/hot water circuit. This takes a few minutes.
Place a container under the co ee dispensing spout.
1
Check that the machine shows this display.
2
Green
Select the pre-ground co ee brewing function by pressing the “ ”
3
button. The machine shows this display.
Green
Note:
Do not add pre-ground co ee into the compartment.
Press the “ ” button. The machine starts dispensing water.
4
When the dispensing has nished, empty the container. Repeat the
5
operations from step 1 to step 4 twice, then continue with step 6.
Place a container under the steam wand.
6
GreenRed
Press the “ ” button. The following icon is displayed.
7
Press the “ ” button to start dispensing hot water.
8
Dispense water until the no water icon appears.
9
ENGLISH
15
15
At the end, ll the water tank again up to the MAX level. Now the ma-
10
chine is ready for co ee brewing.
The display to the left will be shown.
Verde
Note:
When you haven’t used the machine for 2 or more weeks, the machine
will automatically perform an automatic rinse/self-cleaning cycle after you
switch it on. Following this, you need to initiate a manual rinse cycle as
described above.
The automatic rinse/self-cleaning cycle starts automatically when the machine has been in stand-by mode or turned o for more than 15 minutes.
At the end of the cycle, it is possible to brew a co ee.
16
ENGLISH
C
B
Measuring and Programming Water Hardness
Water hardness measuring is very important in order to de ne the descaling frequency and to install the “INTENZA+” water lter (for more detail on
the water lter, see next chapter).
To measure the water hardness follow the steps below:
Immerse the water hardness test strip (supplied with the machine) in
1
water for 1 second.
Note:
The test strip can only be used for one single measurement.
Wait for one minute.
2
Check how many squares have changed the colour to red and then
3
refer to the table.
Note:
The numbers on the water hardness test strip correspond to the water
hardness adjustment settings.
More precisely:
1 = 1 (very soft water)
2 = 2 (soft water)
3 = 3 (hard water)
4 = 4 (very hard water)
Intenza Aroma System
A
23 4
1
The letters correspond to the references that are located at the base of the
“INTENZA+” water lter (see next chapter).
Machine Water Hardness Setting
Now you can program the water hardness setting. Press the
4
button and scroll the pages by pressing the
Yellow
lowing icon is displayed.
Note:
The machine is supplied with standard water hardness setting, suitable for
most types of water.
“ ”
button until the fol-
“ ”
ENGLISH
Press the “ ” button to increase the value or the “ ” button to
5
decrease the value.
Yellow
Green
Press the
6
Press the “ ” button to exit the programming MENU. The machine
7
shows this display and is ready to brew.
“ ”
button to con rm the setting.
“INTENZA+” Water Filter Installation
We recommend installing the “INTENZA+” water lter as this prevents
limescale build-ups and preserves a more intense aroma to your espresso
co ee.
The INTENZA+ water lter can be purchased separately. Please refer to the
maintenance product page in this user manual for further details.
Water is a crucial part of every espresso, so it’s most important to always
have it professionally ltered. Using the “INTENZA+” water lter will prevent
mineral deposits from building up and improve your water quality.
17
17
Remove the small white lter from the water tank and store it in a dry
1
place.
Remove the “INTENZA+” water lter from its packaging, immerse it ver-
2
tically (with the opening positioned upwards) in cold water and gently
press the sides so as to let the air bubbles out.
18
ENGLISH
Set the lter according to the measurements performed (see previous
3
chapter) and indicated on the base of the lter:
A = soft water – equals 1 or 2 on the test strip
B = hard water (standard) – equals 3 on the test strip
C = very hard water – equals 4 on the test strip
Insert the lter into the empty water tank. Press it down until it cannot
4
move any further.
Fill the water tank with fresh water and reinsert it into the machine.
5
Dispense all the water of the tank by using the hot water function (see
6
“Hot Water Dispensing” chapter).
Fill the water tank again.
7
Press the “ ” button and scroll the pages by pressing the “ ” but-
8
ton until the following screen is displayed.
Yellow
Press the “ ” button to select “ON” and press the “ ” button to
9
con rm.
Yellow
To exit, press the “ ” button. The machine shows this display and is
10
ready to brew.
Green
In this way the machine has been programmed to inform the user of
the need to replace the “INTENZA+” water lter.
Loading...