![](/html/2a/2ae9/2ae9f064e6ebee0f6fffcca4c669d4e896e0417f8c0b20196bfa3db7d161248b/bg1.png)
Coffee maker Essence II
HD7624/01
Philips Domestic Appliances and Personal Care
Service Manual
PRODUCT INFORMATION
Voltage : 100 V, 120 V, 220 - 240 V
Frequency : 50 - 60 Hz
Power consumption : 1400 W
Coloursetting : White / vapour dusk
Contents : 1200 cc
Colour code identifi cation:
To determine which service manual is suitable for the
appliance that has to repaired please check the following.
Look at the type plate identifi cation from the appliance on
the second row.
The fi rst sledge number is the colour code for that
appliance. ( /99 )
(for example below the colour code is /01)
Example of a type plate:
TYPE HD7624
/01 /A
…
…
At the service manual heading, the type and colour code
are also mentioned for example HD7624/01
/01 is the colour code.
SAP coding HD7624/01
ASO switch
L
N
Descaling:
Regular de-scaling will prolong the life of your appliance and
will guarantee optimal brewing results.
Follow below steps to de-scale the appliance.
1. Fill the water tank with white vinegar.
2. Let the appliance complete two runs.
3. Let the appliance complete two more fl ushing cycles
with clean water to rinse away all vinegar.
If the above procedure does not restore the function, then
switch off the coffee maker when the acid passed through
during appr. 3 min.
Keep the appliance in this condition overnight and continue
the steps see above procedure.
Thermostat
Element
1400 W
Thermal
fuse
This product meets the requirements regarding interference suppression on radio and TV.
Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification
After the product has been repaired, it should
function properly and has to meet the safety
requirements as offi cially laid down at this
moment.
4322 277 00948
03/07
![](/html/2a/2ae9/2ae9f064e6ebee0f6fffcca4c669d4e896e0417f8c0b20196bfa3db7d161248b/bg2.png)
Repair instruction for replacing switch:
If the switch has to be replaced please follow the next steps:
• Remove bottom base plate.
• Pull the complete pump unit (including hose pieces) downwards until the hose
pieces are loosened from the two water tank pipes. (hose pieces and wires
must stay connected to the pump).
• Remove the complete top cover including the water tank. (see picture 1)
• Now it is possible to replace the switch.
• To replace the switch, fi rst remove the switch cap from the switch by means
of a small screwdriver. (The cap has to be loosened at the inner side of the
housing by bending a little bit the plastic paw from the switch cap)
picture 1
START
POSITION
1
REMOVE THE
CAP IN THIS
END
POSITION
2
HOUSING
PA RT
DIRECTION
SMALL
DETENT
PIECE A
• Place the new switch en connect the wires, push the plastic switch cap back on the switch.
• Insert the complete top cover assy including plastic tank gently back into the housing.
• Take the pump unit and attach the hose pieces to the water tank pipes of the previously inserted tank.
(be sure that the hose pieces are well attached to the water tank pipes, otherwise leakage problems can occur)
• Assemble the base plate again.
Transportation lock:
To prevent damaging the dosing/weighting system in case the appliance has to
be shipped/transported, It is possible to order a special transportation lock.
For the position of the transportation lock see picture 2.
4222 247 59510
The code number transportation lock: 4222 247 59510
Commercial trade number jug + lid: HD7965/01 (vapour dusk)
picture 2