Philips HB822-A Service Manual

HPA Solarium

HB822/A

Philips Domestic Appliances and Personal Care

Service Manual

TECHNICAL DATA

Input consumption : 1350 W / 230 V

UV-A source : 3x HPA Flexpower 400-600

Ballast : 3x BHA400L / 230 V

Starter : 3x SN 58-spec.

Timer : 60 mins motor driven

Radiation area : 185 x 75 cm

Protecting goggles : HB072 - 4822 690 80147

2

Output UVX-36 meter : min. 4.2 mW/cm

at 65 cm

Production code YYWW : on type plate

S3

NTC

3

FLOOR PART

L3

HB 814
HB 824

H

SK1

L

Re1

a1b1

SK2

M

a

TIMER

N

C1

SK3

S1

NTC

NTC

2

1

L2

L1

S2

LA1 LA2 LA3

SK4 SK5 TCO

RADIATION PART

Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification

M

4322 277 01039
02/09

HB822/A

IMPORTANT

- On account of the short high starting current, the house
fuse should be of a 16 A-delayed type.

- The appliance will work in operating position only.

- Always check if the protecting glass pane (item 8) is
fi tted after a repair.

- HPA lamps only start when they have cooled down
suffi ciently.

- Never touch a HPA lamp with your fi ngers.
If necessary, clean the lamp with alcohol.

- Colour differences may occur when new lamps are
installed. This phenomenon is characteristic of HPA
lamps and disappears after a short period of use.

- After assembly the glass fi lter should be free from fi nger
prints and dust.
Clean the glass fi lter with alcohol, if necessary.

- Never look in the direction of the radiation part while the
lamps are on without wearing protecting goggles.

- In case of insuffi cient cooling (e.g. when the ventilation
apertures are blocked or when the fan is defective) the
safety device (item 9) will automatically switch off the
solarium.
Once the cause of overheating has been removed and
the solarium has cooled down suffi ciently, the appliance
will switch on again automatically.

- When the appliance is a few years old, we advise you to
apply a drop of thin oil to the bearings of the fan.

- Let the solarium cool down fi rst (approx. 15 mins) before
closing and storing it away.

HINTS FOR REPAIRS

- Disassembly of the radiation part:

1. Remove the 10 screws with which the housing
(item 7) is fastened to the cover (item 1).
The housing will continue to cling to the cover.

2. Disconnect the connectors of the connecting cable
and motor.

3. Undo the other connections.

- It can be established whether lamps, ballasts or starters
are defective by interchanging them.

- When replacing a lamp holder (item 10) 2 tubular rivets
must be drilled out.
The bracket is fastened with 2 M2.5 x 10 bolts.

- Disassembly of the fl oor part:

1. Remove 6 square and 3 round ornamental props

(item 20).

2. Loosen 14 visible screws by which the cover (item 18)

is fastened.

3. Pass the mains cord cover (item 31) and the timer

cover (item 16) through the opening below, after the
screws have been taken out.

4. Loosen the screw under the timer cover.

5. Remove the cover (item 18) in horizontal position so

that the screws will not fall out.
(As screws with varying length are used, it is not
possible to interchange them.)

- The wheel can be replaced after the decorative cap has
been removed by means of a small screwdriver.

- A burned NTC resistor or overheated wiring points
to a wiring fault at the connecting block (item 21).

- Only move the solarium when folded.

- In case of complaints about little or no tanning, the
output can be measured by means of a so-called
UVX-36 meter.
The fi gure given on the title sheet is the minimum value
to be measured in the centre of the radiation fi eld after
5 mins of warming up and with the appliance connected
to the rated voltage.

2-5