Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips
offers, register your product at www.philips.com/welcome.
Read the separate important information leaet and this user manual carefully before you use the
appliance. Keep both documents for future reference.
Product overview (Fig. 1)
1 Spray button
2 Steam slider
a. Dry setting
b. ECO setting
c. Auto steam setting
3 Steam boost trigger
4 Safety auto-off light (specific types only)
5 Temperature indicator light
6 Temperature dial with Auto steam control
7 Calc clean button
8 Built-in calc container
Type of water to use
Your appliance has been designed to be used with tap water. If you live in an area with hard water, fast
scale build-up may occur. Therefore, it is recommended to use distilled or demineralized water to prolong
the lifetime of your appliance.
Do not put perfume, vinegar, starch, descaling agents, ironing aids or other chemicals in the water tank.
Ironing
Please read the quick start guide in this user manual carefully to start using your
appliance. (Fig. 2-10)
Temperature setting
Select the temperature to the appropriate setting for your garment according to table 1 below:
-Auto steam: The iron automatically adjusts the steam output according to the selected temperature
to provide the best ironing result.
-ECO: This steam setting enables you to reduce the steam output to save energy and still have
sufficient steam to iron your garments.
-Dry: This steam setting enables you to iron without steam or to stop steam when the iron is not in use.
-Iron with extra steam: Press and hold the steam boost trigger to get more steam to remove
stubborn creases.
Steam boost function and vertical steaming
-Press and release the steam boost trigger for a powerful boost steam. This can be used to remove
targeted stubborn creases or creases from a hanged garment.
Note: The steam boost function should only be used at temperature setting between ●●● to MAX. Leaking
may appear if you use steam boost at too low a temperature.
Hot steam comes out of the iron. Do not remove wrinkles from a garment while some one is wearing
it. To prevent burns, do not direct the steam at people.
Safety auto-off (specic types only)
The safety auto-off function automatically switches off the iron if it has not been used for 30 seconds
resting on its soleplate or 8 minutes resting on its backplate. The auto-off light will light up.
-To let the iron heat up again, pick up the iron or move it slightly. The auto-off light goes out.
Cleaning and maintenance
Cleaning
1 Unplug the iron and let it cool down.
2 Pour any remaining water out of the water tank from the water lling door.
3 Wipe akes and any other deposit off the soleplate with a damp cloth and a non-abrasive (liquid)
cleaning agent.
To keep the soleplate smooth, avoid hard contact with metal objects. Never use a scouring pad,
vinegar or other chemicals to clean the soleplate.
Calc clean function
IMPORTANT: This iron comes with a Built-in calc container, which collects loose scale particles during ironing. The
calc container is not meant for removal by the user. The scale particles are ushed out of the iron during calc
clean process. Perform calc clean once every 1 month to maintain good steam performance and prolong the
life of your iron. If water in your area is hard, or you see scales coming out from the soleplate during ironing, use
calc clean more frequently.
1 Make sure the iron is unplugged and the steam slider is set to dry setting. (Fig. 11)
2 Fill the water tank to the MAX indication. (Fig. 12)
Do not pour vinegar or other descaling agents into the water tank.
ENGLISH
8
3 Plug in the iron and set the temperature dial to MAX. (Fig. 13-14)
4 Unplug the iron when the temperature light goes out. (Fig. 15-17)
5 Hold the iron over the sink. Keep pushing the calc clean button and gently shake the iron forth and
back until all water in the water tank has been used up (Fig. 18).
Scales is ushed out, steam and boiling water also come out of the soleplate.
Note: Repeat steps 2 to 5 if the water that comes out of the iron still contains scale particles.
6 Plug in the iron and let the iron heat up to dry the soleplate. (Fig. 19)
7 Unplug the iron when the temperature indicator light goes out.
8 Move the iron gently over a piece of cloth to remove any water stains on the soleplate.
Troubleshooting
This chapter summarises the most common problems you could encounter with the appliance. If you are
unable to solve the problem with the information below, visit www.philips.com/support for a list of
frequently asked questions or contact the Consumer Care Centre in your country (see the worldwide
guarantee leaet for contact details).
ProblemPossible causeSolution
Water leaks from the
water filling door.
Water drips from
the soleplate after
the iron has been
unplugged or has
been stored.
The steam boost
function does not
work properly (water
leaks out of the
soleplate).
Flakes and impurities
come out of the
soleplate during
ironing.
You have overfilled the
water tank.
The steam slider is set to
MAX or ECO.
You have put the iron
in horizontal position
with water still left in the
water tank.
You have used the steam
boost function too often
within a very shor t period.
You have used the steam
boost function at too low
a temperature.
Calc are formed inside the
soleplate.
Do not fill the water tank beyond the MAX
indication. Pour excess water out of the water tank.
Set the steam slider to dry setting.
Empty the water tank.
Wait for a few seconds before you use the steam
boost function again.
Set an ironing temperature at which the steam
boost function can be used (●●● to MAX).
Use the calc clean function (see chapter ‘Cleaning
and maintenance’, section ‘calc clean function’).
Loading...
+ 12 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.