Philips FWV595 User Manual

Mini Hi-Fi System

V595



Optimum disc playability : ensuring excellent picture quality

Philips components and modules for the various CD applications have always enjoyed an excellent reputation in the market place for super disc playability - the ability to play discs which may be scratched, soiled or not fully according to the standard specification. This position has been underlined by tests showing the superior performance of the various Philips players, as well as by the positive experiences of millions of individual consumers around the world.

Constantly improving performance

As the penetration of the CD system has increased, and new applications like CD-ROM and Video CD have become commonplace, Philips Components - as the CD technology inventor and as one of the major suppliers of CD player modules in the industry - has constantly improved the performance of its products.

One of the ways in which this benefits users is by optimum disc playability. This is an important parameter for CD players other than CD Audio, and especially for the Video CD applications, because any loss of data from the disc will at best cause disturbances in the reproduced picture, and at worst can cause the player to lose track so that disc playing fails.

Presenting Super Error Correction

To ensure consistently good results when playing Video CD discs of all quality grades and conditions, Philips has introduced further improvements in the system's playability. These developments together are called Super Error Correction, a proprietary Philips technology optimizing the system's ability to handle lessthan-perfect discs with the minimum disturbance to normal playing.

By effectively eliminating virtually all errors arising under normal playing conditions, Super Error Correction ensures that the picture quality as seen by the user is independent of disc play. The video encoding and processing during mastering of the disc, and the MPEG-1 decoding and video encoding in the signal processing stages, are now the only limiting factors for picture quality.

FW-

VCD MINI HIFI SYSTEM

DISC

CHANGE

OPEN• CLOSE

CD 1•2•3

BAND

CDR/DVD

TAPE 1•2

PROG

DUBBING REC

CLOCK• TIMER

AUTO

REPLAY

STANDBY-ON

DISC DIRECT PLAY

DISC

CD SYNCHRO RECORDING

CD/CD-R/CD-RW COMPATIBLE

INTERACTIVE VU METER

VOLUME

DEMO STOP/ CLEAR

PLAY•

PAUSE

•

DISC

VCD PAL/

NTSC

TUNER

TAPE AUX

SOURCE

DISPLAY

PBC

RETURN

MP3-CD

TITLE/ ALBUM NAME

MIC/

LEVEL

•

MAX BASS DYNAMIC AMPLIFICATION

CONTROL (DAC)

∞

)

™

≤

0 !

(

Index

English ------------------------------------------------ 6

-------------------------------------------------------- 33

Bahasa Melayu ----------------------------------- 61

Bahasa Indonesia -------------------------------- 89

English

Bahasa Melayu

Bahasa Indonesia

CAUTION

Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation.

Contents

English

General Information

Environmental Information ................................ 7

Supplied Accessories ........................................... 7

Safety Information ................................................ 7

Preparations

Rear Connections ............................................ 8–9

Inserting batteries into the remote

control .................................................................... 9

Controls

Controls on the system and remote

control ........................................................... 10–12

Basic Functions

Plug and Play ........................................................ 13

Demonstration mode ........................................ 13

Switching the system on ................................... 14

Switching the system to Standby mode ........ 14

Power Saving Automatic Standby .................... 14

Display mode....................................................... 14

Volume Control .................................................. 14

Sound Navigation ............................................... 15

CD/VCD/MP3-CD Operation

Discs for Playback .............................................. 16

Loading Discs ...................................................... 17

Disc Playback ....................................................... 17

Replace discs during playback.......................... 17

Select a desired track/passage ......................... 18

Programming the disc tracks .................... 18–19

Repeat ................................................................... 19

Title/Album Name ............................................. 19

VIDEO CD

Adjusting the TV System ................................... 20

OSD – On Screen Display ............................... 20

Playing a Video CD with PBC .......................... 20

Return ................................................................... 21

Digest .................................................................... 21

A-B Repeat .......................................................... 21

Zoom .................................................................... 21

Resume ................................................................. 22

Slow ....................................................................... 22

Vocal ...................................................................... 22

Key Control ......................................................... 22

Echo ....................................................................... 22

Radio Reception

Storing Preset Radio Stations ................... 23–24

Tuning to Preset Radio Stations ...................... 24

Erasing a Preset Radio Station ........................ 24

Changing Tuning Grid ........................................ 24

Ta pe Operation/Recording

Ta pe Playback ...................................................... 25

General Information on Recording ................ 26

Preparation for Recording ............................... 26

One Touch Recording/Recording the

mixed sound ........................................................ 26

CD/VCD/MP3-CD Synchro Recording..............

......................................................................... 26–27

Dubbing Tapes ..................................................... 27

Karaoke

Microphone Mixing ............................................ 27

Clock/Timer

View Clock .......................................................... 28

Clock Setting ....................................................... 28

Timer Setting ................................................ 28–29

External Sources

Listening to External Sources .......................... 29

Specifications ........................................... 30

Maintenance.............................................. 31

Troubleshooting ............................. 31–32

General Information

IMPORTANT! PLEASE NOTE THAT THE VOLTAGE SELECTOR LOCATED AT THE REAR OF THIS SYSTEM IS PRESET AT 220V FROM THE FACTORY. FOR COUNTRIES THAT OPERATE AT 110V-127V, PLEASE ADJUST TO 110V-127V BEFORE YOU SWITCH ON THE SYSTEM.

Environmental Information

All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet).

Your system consists of materials which can be recycled and reused if disassembled by a specialised company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.

Supplied accessories

– Remote control – Batteries (two AA size) for remote control – AM loop antenna – FM wire antenna –AC power cord – One Video cinch cable

Safety Information

● Before operating the system, check that the

operating voltage indicated on the typeplate (or the voltage indication beside the voltage selector) of your system is identical with the voltage of your local power supply. If not, please consult your dealer.

● Place the system on a flat, hard and stable

surface.

● Place the system in a location with adequate

ventilation to prevent internal heat build-up in your system. Allow at least 10 cm (4 inches) clearance from the rear and the top of the unit and 5 cm (2 inches) from each side.

● Do not expose the system, batteries or discs to

excessive moisture, rain, sand or heat sources caused by heating equipment or direct sunlight.

● If the system is brought directly from a cold to a

warm location, or is placed in a very damp room, moisture may condense on the lens of the disc unit inside the system. Should this occur, the CD player would not operate normally. Leave the power on for about one hour with no disc in the system until normal playback is possible.

● The mechanical par ts of the set contain self-

lubricating bearings and must not be oiled or lubricated.

● When the system is switched to Standby

mode, it is still consuming some power. To disconnect the system from the power supply completely, remove the AC power plug from the wall socket.

English

The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

Preparations

SPEAKERS 6Ω

–

SUBWOOFER

OUT

AUX/

CDR

AM ANTENNA

MAINS

speaker

(right)

speaker

(left)

AC power cord

FM wire

antenna

FM ANTENNA

VOLTAGE SELECTOR

110V127V

220V240V

VIDEO

Television

AUDIO

OUT

AM loop

antenna

VIDEO OUT

(CVBS)

SPEAKERS 6Ω

–

BOOSTER IN

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

POWER SWITCH

OFF

AC MAINS

booster

speaker

(left)

booster

speaker

(right)

RLR

AC power cord

VOLTAGE

SELECTOR

110V- 127V

220V- 240V

BOOSTER

OUT

VOLTAGE

SELECTOR

110V127V

220V240V

English

Rear Connections

The type plate is located at the rear of the system.

A Powe r

Before connecting the AC power cord to the wall outlet, ensure that the following are done; – If your system is equipped with a Voltage Selector, set the VOLTAGE SELECTOR to the local power line voltage. – All other connections have been made.

WARNING! –For optimal performance, use only the original power cable. –Never make or change any connections with the power switched on.

To avoid overheating of the system, a safety circuit has been built in. Therefore, your system may switch to Standby mode automatically under extreme conditions. If this happens, let the system cool down before reusing it (not available for all versions).

B Antennas Connection

Connect the supplied AM loop antenna and FM antenna to the respective terminals. Adjust the position of the antenna for optimal reception.

AM Antenna

● Position the antenna as far as possible from a TV,

VCR or other radiation source.

FM Antenna

● For better FM stereo reception, connect an

outdoor FM antenna to the FM ANTENNA terminal.

C Speakers Connection

SPEAKERS 6Ω

–

BOOSTER IN

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

POWER SWITCH

OFF

RLR

2 4

VOLUME

AC MAINS

VOLTAGE SELECTOR

110V- 127V

220V- 240V

Front Speakers

Connect the speaker wires to the SPEAKERS (FRONT) terminals, right speaker to "R" and left speaker to "L", coloured (marked) wire to "+" and black (unmarked) wire to "-".

● Fully inser t the stripped por tion of the speaker

wire into the terminal as shown.

Notes: –For optimal sound performance, use the supplied speakers. – Do not connect more than one speaker to any one pair of +/- speaker terminals. – Do not connect speakers with an impedance lower than the speakers supplied. Please refer to the SPECIFICATIONS section of this manual.

D Video Out Connection

Connect the VIDEO OUT (CVBS) terminal at the rear of the system to the TV or VCR VIDEO IN for viewing or recording.

Note: –To avoid magnetic interference with the picture on your TV, do not position the front speakers too close to the TV.

E Connecting other equipment to your

system

Connect the audio left and right OUT terminals of a TV, VCR, Laser Disc player, DVD player or CD Recorder to the AUX/CDR IN terminals.

Note: – If you are connecting equipment with a mono output (a single audio out terminal), connect it to the AUX/CDR IN left terminal. Alternatively, you can use a “single to double” cinch cable (still be mono sound).

F Power Booster Connection

1 Connect the BOOSTER OUT (Right and Left)

terminals of the mini system to the power booster amplifier BOOSTER IN (Right and

Preparations

English

Left) terminals respectively.

2 Connect the speaker wires to the BOOSTER

SPEAKERS terminals, right speaker to "R" and left speaker to "L", coloured (marked) wire to "+" and black (unmarked) wire to "-".

3 Set the VOLTA GE SELECTOR to the local

power line voltage.

4 Plug in the AC mains to the wall socket. 5 Switch on the POWER SWITCH to activate

the power booster amplifier.

6 Press STANDBY ON y button to switch the

system ON or to Standby mode.

7 Rotate the VOLUME control to adjust the

loudness of the power booster amplifier.

Inserting batteries into the Remote Control

Insert two batteries (Type R06 or AA) into the remote control with the correct polarity as indicated by the + and - symbols inside the battery compar tment.

CAUTION! – Remove batteries if they are exhausted or not to be used for a long time. – Do not use old and new or different types of batteries in combination. – Batteries contain chemical substances, so they should be disposed off properly.

Controls (main system’s illustration on page 3)

VOLUME

TAPE 1/2

OSD

VCD 123

AUX

TUNER

REPEATPROG

VAC

DSC

MAXECHO

RETURN

PBC

DIGEST

TITLE

ALBUM

TITLE/

ALBUM

NAME

A-B

RESUME

ZOOM

SLOW

VOCAL

KEY CONTROL

≤ 8

(

≥

! ™ ¡

• ª

⁄

‹

›

ﬁ

ﬂ

‡

MP3 123

DBB

English

Notes for remote control: – First, select the source you wish to control by pressing one of the source select keys on the remote control (VCD 123 or TUNER, for example). – Then select the desired function (É,

, for example).

Controls on the system and remote control

1 STANDBY ON y

– to switch the system on or to Standby mode.

2 DISPLAY SCREEN

– to view the current status of the system.

3 DISC TRAYS 4 DISC CHANGE

–to change disc(s).

5 DISC 1 / DISC 2 / DISC 3

– to select a disc tray for playback.

6 OPEN•CLOSE

– to open or close the disc tray.

7 INTERACTIVE VU METER

– to show the VU (volume unit) meter in music or

volume mode depending on the display mode selected.

8 VOLUME

– to increase or decrease the volume.

9 Tape Deck Operation

AUTO REPLAY

–to select continuous playback in either AUTO

PLAY or ONCE mode only.

DUBBING

– to dub a tape.

REC

– to start recording on tape deck 2.

0 SOUND NAVIGATION

– to select the desired sound feature : DSC, VAC,

or DBB.

! JOG CONTROL

– to select the desired sound effect for the

selected sound feature.

DSC ..................DIGITAL, ROCK, POP, NEWAGE,

CLASSIC or ELECTRIC.

VAC .................. HALL, CONCERT, CINEMA,

DISCO, ARCADE or CYBER.

DBB .................. BEAT, PUNCH or BLAST.

@ INCREDIBLE SURROUND (IS)

– to activate or deactivate the surround sound

effect.

# MAX SOUND (MAX)

– to activate or deactivate the optimal mix of

various sound features.

+ 22 hidden pages