Philips DVP-3358-K, DVP-3358 Service Manual

DVP3358(K)

DVP3358K/93

DVP3358/96

Service Manual

TABLE OF CONTENTS

. Technical Specifications…………....………………………..............1-2

. Safety Instruction, Warning & Notes….……………………....….....1-3

. DFU Instruction..............................................................................2-1

. Mechanical and Dismantling Instructions…………........................3-1

. Software Version & Upgrades, Region Code Change..…….........

. Trouble Shooting Chart………………………………………………

. Wiring Diagram………………………………………..………..….….6-1

. Electrical Diagrams and Print-layouts..….…………………....….…7-1

. Set Mechanical Exploded view & Part list.…………………..….….8-1

. Revision List..................................................................................9-1

transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise

without the prior permission of Philips.

Page

4-1

5-1

CLASS 1

LASER PRODUCT

Published by FK-091

Version 1.1

5 BU AVM Printed in The Netherlands Subject to modification

3142 785 33631

PHILIPS

6SHFLÀFDWLRQ

for DVP3358K/93

Note



6SHFLÀFDWLRQDQGGHVLJQDUHVXEMHFWWRFKDQJH

without notice.

Accessories supplied

Remote control and batteries Audio/video cables AC Power cable User Manual

Playback media

DVD-Video, Video CD/SVCD, Audio CD, CD-R/ CD-RW, DVD+R/+RW, DVD-R/-RW, DivX-CD,

3LFWXUH&'03&':0$&'86%ÁDVKGULYH

1-2

Frequency response: 

DVD: 4 Hz - 22 kHz (48 kHz); 

4 Hz - 44 kHz (96 kHz)

SVCD: 4 Hz - 20 kHz (44.1 kHz); 

4 Hz - 22 kHz (48 kHz)

CD/VCD: 4 Hz - 20 kHz (44.1 kHz)

Signal-Noise (1 kHz): > 90 dB Dynamic range (1 kHz): > 80 dB Crosstalk (1 kHz): > 70 dB Distortion/noise (1 kHz): > 65 dB MPEG MP3: MPEG Audio L3

Audio format

Digital:

MPEG/AC-3/PCM: Compressed digital (16, 20, 24  bits fs, 44.1, 48, 96 kHz) MP3 (ISO 9660): 96, 112, 128, 256 kbps &  variable bit rate fs, 32, 44.1, 48 kHz

Analog sound stereo Dolby surround compatible downmix from Dolby 

Digital multi-channel sound

USB

Compatibility: Hi-Speed USB (2.0) Class support: UMS (USB Mass Storage Class) 

TV standard

Number of lines:

625 (PAL/50Hz); 525 (NTSC/60Hz)

Playback: Multi-standard (PAL/NTSC)

Video performance

Video DAC: 12 bits, 108 MHz Y Pb Pr: 0.7 Vpp ~ 75 ohm Video output: 1 Vpp ~ 75 ohm

Video format

Digital compression: 

MPEG 2: DVD/SVCD  MPEG 1: VCD/DivX

Horizontal resolution: 

DVD: 720 pixels (50 Hz); 720 pixels (60 Hz)  VCD: 352 pixels (50 Hz); 352 pixels (60 Hz) 

Vertical resolution: 

DVD: 576 lines (50 Hz); 480 lines (60 Hz)  VCD: 288 lines (50 Hz); 240 lines (60 Hz) 

Connections

Y Pb Pr output: Cinch 3x Video output: Cinch (yellow) Audio output (L+R): Cinch (white/red) Digital output: 

1 coaxial: IEC60958 for CDDA/LPCM;

IEC61937 for MPEG 1/2, Dolby Digital

Main unit

Dimensions (w x h x d): 360 x 38 x 203 (mm) Net Weight: approximately 1.3 kg

Power

Power supply rating: 110 V - 240V; 50/60 Hz Power consumption: < 10 W Power consumption in standby mode: < 1 W

/DVHU6SHFLÀFDWLRQ

Type: Semiconductor laser InGaAIP (DVD), AIGaAs  (CD)

Wave length: 658 nm (DVD), 790 nm (CD) Output Power: 7.0 mW (DVD), 10.0 mW (VCD/CD) Beam divergence: 60 degrees

Audio performance

DA converter: 24 bits, 192 kHz

Speciﬁ cation

for DVP3358/96

Note

Speciﬁ cation and design are subject to change

•

without notice.

Accessories supplied

Remote control and batteries• Audio/video cables•

Playback media

DVD-Video, Video CD/SVCD, Audio CD, CD-R/• CD-RW, DVD+R/+RW, DVD-R/-RW, DivX-CD, Picture CD, MP3-CD, WMA-CD, USB ﬂ ash drive

USB

Compatibility: Hi-Speed USB (2.0)• Class support: UMS (USB Mass Storage Class) •

TV standard

Number of lines:•

625 (PAL/50Hz); 525 (NTSC/60Hz)•

Playback: Multi-standard (PAL/NTSC)•

Video performance

Video DAC: 12 bits, 108 MHz• Y Pb Pr: 0.7 Vpp ~ 75 ohm• Video output: 1 Vpp ~ 75 ohm•

Video format

Digital compression: •

MPEG 2: DVD/SVCD • MPEG 1: VCD/DivX•

Horizontal resolution: •

DVD: 720 pixels (50 Hz); 720 pixels (60 Hz) • VCD: 352 pixels (50 Hz); 352 pixels (60 Hz) •

Vertical resolution: •

DVD: 576 lines (50 Hz); 480 lines (60 Hz) • VCD: 288 lines (50 Hz); 240 lines (60 Hz) •

1-2

Frequency response: •

DVD: 4 Hz - 22 kHz (48 kHz); • 4 Hz - 44 kHz (96 kHz) SVCD: 4 Hz - 20 kHz (44.1 kHz); • 4 Hz - 22 kHz (48 kHz) CD/VCD: 4 Hz - 20 kHz (44.1 kHz)•

Signal-Noise (1 kHz): > 90 dB (A-weighted)• Dynamic range (1 kHz): > 80 dB (A-weighted)• Crosstalk (1 kHz): > 70 dB• Distortion/noise (1 kHz): > 65 dB• MPEG MP3: MPEG Audio L3•

Audio format

Digital:•

MPEG/AC-3/PCM: Compressed digital (16, 20, 24 • bits fs, 44.1, 48, 96 kHz) MP3 (ISO 9660): 96, 112, 128, 256 kbps &• variable bit rate fs, 32, 44.1, 48 kHz

Analog sound stereo• Dolby surround compatible downmix from Dolby •

Digital multi-channel sound

Connections

Y Pb Pr output: Cinch 3x• Video output: Cinch (yellow)• Audio output (L+R): Cinch (white/red)• Digital output: •

1 coaxial: IEC60958 for CDDA/LPCM;• IEC61937 for MPEG 1/2, Dolby Digital

5.1 channel analog output• Audio Front L + R: Cinch (white/red)•

Audio Rear L + R: Cinch (white/red)• Audio Center: Cinch (blue)• Audio Subwoofer: Cinch (black)•

Main unit

Dimensions (w x h x d): 360 x 37 x 209 (mm)• Net Weight: approximately 1.3 kg•

Power

Power supply rating: 110 V - 240V; 50/60 Hz• Power consumption: < 10 W• Power consumption in standby mode: < 1 W•

Audio performance

DA converter: 24 bits, 192 kHz•

Laser Speciﬁ cation

Type: Semiconductor laser InGaAIP (DVD), AIGaAs • (CD)

Wave length: 658 nm (DVD), 790 nm (CD)• Output Power: 7.0 mW (DVD), 10.0 mW (VCD/CD)• Beam divergence: 60 degrees•

1-3

Safety instruction, Warning & Notes

Safety instruction

1. General safety

Safety regulations require that during a repair:

. Connect the unit to the mains via an isolation transformer.

. Replace safety components indicated by the symbol

only by components identical to the original ones. Any

other component substitution (other than original type)

may increase risk of fire or electrical shock hazard.

Safety regulations require that after a repair, you must

return the unit in its original condition. Pay, in particular,

attention to the following points:

. Route the wires/cables correctly, and fix them with the

mounted cable clamps.

. Check the insulation of the mains lead for external

damage.

. Check the electrical DC resistance between the mains

plug and the secondary side:

1) Unplug the mains cord, and connect a wire between

the two pins of the mains plug.

2) Set the mains switch the “on” position (keep the

mains cord unplug).

3) Measure the resistance value between the mains

plug and the front panel, controls, and chassis

bottom.

4) Repair or correct unit when the resistance

measurement is less than 1M

5) Verify this, before you return the unit to the

customer/user (ref. UL-standard no. 1492).

6) Switch the unit “off”, and remove the wire between

the two pins of the mains plug.

2.Laser safety

This unit employs a laser. Only qualified service personnel

may remove the cover, or attempt to service this device

(due to possible eye injury).

Laser device unit

Type : Semiconductor laser GaAlAs

Wavelength : 650nm (DVD)

: 780nm (VCD/CD)

Output power : 7mW (DVD)

: 10mW (DVD /CD)

Beam divergence: 60 degree

Note: Use of controls or adjustments or performance of

procedure other than those specified herein, may result in

hazardous radiation exposure. Avoid direct exposure to

beam.

Warning

1-4

1.General

. All ICs and many other semiconductors are susceptible to

electrostatic discharges (ESD). Careless handing during

repair can reduce life drastically. Make sure that, during

repair, you are at the same potential as the mass of the

set by a wristband with resistance. Keep components and

tools at this same potential. Available ESD protection

equipment:

1) Complete kit ESD3 (small tablemat, wristband,

connection box, extension cable and earth cable)

4822 310 10671.

2) Wristband tester 4822 344 13999.

. Be careful during measurements in the live voltage

section. The primary side of the power supply , including

the heat sink, carries live mains voltage when you

connect the player to the mains (even when the player is

“off”!). It is possible to touch copper tracks and/or

components in this unshielded primary area, when you

service the player. Service personnel must take

precautions to prevent touching this area or components

in this area. A “lighting stroke” and a stripe-marked

printing on the printed wiring board, indicate the primary

side of the power supply.

. Never replace modules, or components, while the unit is

“on”.

2. Laser

. The use of optical instruments with this product, will

increase eye hazard.

. Only qualified service personnel may remove the cover

or attempt to service this device, due to possible eye

injury.

. Repair handing should take place as much as possible

with a disc loaded inside the player.

. Text below is placed inside the unit, on the laser cover

shield:

CAUTION: VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN, AVOID EXPOSURE

TO BEAM.

Notes: Manufactured under licence from Dolby

Laboratories. The double-D symbol is trademarks of Dolby

Notes

Lead-Free requirement for service

1-5

INDENTIFICATION:

Regardless of special logo (not always indicated)

One must treat all sets from 1.1.2005 onwards, according next rules.

Important note be treated in this way as long as you avoid mixing solder-alloys (leaded/ lead-free). So best to always use SAC305 and the higher temperatures belong to this.

Due to lead-free technology some rules have to be respected by the workshop during a repair:

x Use only lead-free solder alloy Philips SAC305 with

order code 0622 149 00106. If lead-free solder-paste is

required, please contact the manufacturer of your

solder-equipment. In general use of solder-paste within

workshops should be avoided because paste is not easy

to store and to handle.

x Use only adequate solder tools applicable for lead-free

solder alloy. The solder tool must be able

o To reach at least a solder-temperature of 400°C,

o To stabilize the adjusted temperature at the

o To exchange solder-tips for different applications.

x Adjust your solder tool so that a temperature around

360°C

joint. Heating-time of the solder-joint should not exceed

~ 4 sec. Avoid temperatures above 400°C otherwise

wear-out of tips will rise drastically and flux-fluid will be

destroyed. To avoid wear-out of tips switch off un-used

equipment, or reduce heat.

x Mix of lead-free solder alloy / parts with leaded solder

alloy / parts is possible but PHILIPS recommends

strongly to avoid mixed

solder alloy types (leaded and lead-free). If one cannot

avoid, clean carefully the

solder-joint from old solder alloy and re-solder with new

solder alloy (SAC305).

: In fact also products a little older can also

solder-tip

– 380°C is reached and stabilized at the solder

x Use only original spare-parts listed in the

Service-Manuals. Not listed standard-material

(commodities) has to be purchased at external

companies.

x Special information for BGA-ICs:

- always use the 12nc-recognizable soldering

temperature profile of the specific BGA (for

de-soldering always use highest lead-free

temperature profile, in case of doubt)

- lead free BGA-ICs will be delivered in so-called

‘dry-packaging’ (sealed pack including a silica gel

pack) to protect the IC against moisture. After

opening, dependent of MSL-level seen on

indicator-label in the bag, the BGA-IC possibly

still has to be baked dry. This will be

communicated via AYS-website.

Do not re-use BGAs at all.

x For sets produced before 1.1.2005, containing

leaded soldering-tin and components, all needed

spare-parts will be available till the end of the

service-period. For repair of such sets nothing

changes.

x On our website:

www.atyourservice.ce.Philips.com

You find more information to:

BGA-de-/soldering (+ baking instructions)

Heating-profiles of BGAs and other ICs used in

Philips-sets

You will find this and more technical information

within the “magazine”, chapter “workshop news”.

For additional questions please contact your local

repair-helpdesk.

DVP3358K/93

2-1

Product overview

Main unit

(Standby-on)

Turn on the DVD player or switch to • standby mode.

Disc compartment

Remote control

31 2

Display panel

Z (Open/Close)

Open or close the disc compartment.•

u (Play/Pause)

Start, pause or resume disc play.•

(USB) jack

Connect a USB ﬂ ash drive.•

MIC

Audio input from a microphone.•

(Standby-On)

Turn on the DVD player or switch to • standby mode.

Z (Open/Close)

Open or close the disc compartment.•

DISC MENU

Access or exit the disc menu.•

Switch to disc mode.•

For VCD/SVCD, turn PBC (Playback • Control) on or off in PBC mode.

DVP3358K/93

v V b B (Navigation buttons)

Navigate through the menus.• Search fast-forward (• B) or fast-

backward (b). Press repeatedly to change the search speed.

Search slow-forward (• v) or slowbackward (V). Press repeatedly to change the search speed.

2 BACK

Return to the previous display menu.•

For DVD, navigate to the title menu.•

For VCD version 2.0 or SVCD with • PBC turned on, return to the menu.

í/ë (Previous/Next)

Skip to the previous or next title, • chapter, or track.

Press and hold for fast-backward or • fast-forward search.

2-2

AUDIO/CREATE MP3

Select an audio language/channel.•

Access the menu to create MP3.•

x (Stop)

Stop disc play.•

u (Play/Pause)

Start, pause or resume disc play.•

INFO

For disc, display the current status or • disc information.

For slideshows, display a thumbnail view • of photo ﬁ les.

Conﬁ rm an entry or selection.•

SETUP

Access or exit the setup menu.•

j ,

(USB)

Switch to USB mode and display the • content.

Numeric buttons

Select an item to play.•

SUBTITLE

Select DVD or DivX subtitle language.•

Access the menu to USB copy or USB • delete.

ZOOM

Fit the picture format to the TV screen.•

Zoom in or out of the picture.•

VOCAL

Change the audio channel of a karaoke • disc.

KARAOKE

Access or exit the karaoke menu.•

DVP3358/96

2-1

Product overview

Main unit

(Standby-on)

Turn on the DVD player or switch to • standby mode.

Disc compartment

Remote control

31 2

Display panel

Z (Open/Close)

Open or close the disc compartment.•

u (Play/Pause)

Start, pause or resume disc play.•

(USB) jack

Connect a USB ﬂ ash drive.•

(Standby-On)

Turn on the DVD player or switch to • standby mode.

Z (Open/Close)

Open or close the disc compartment.•

DISC MENU

Access or exit the disc menu.•

Switch to disc mode.•

For VCD/SVCD, turn PBC (Playback • Control) on or off in PBC mode.

DVP3358/96

v V b B (Navigation buttons)

2-2

AUDIO/CREATE MP3

Navigate through the menus.• Search fast-forward (• B) or fast-

backward (b). Press repeatedly to change the search speed.

Search slow-forward (• v) or slowbackward (V). Press repeatedly to change the search speed.

2 BACK

Return to the previous display menu.•

For DVD, navigate to the title menu.•

For VCD version 2.0 or SVCD with • PBC turned on, return to the menu.

í/ë (Previous/Next)

Skip to the previous or next title, • chapter, or track.

Press and hold for fast-backward or • fast-forward search.

Select an audio language/channel.•

Access the menu to create MP3.•

x (Stop)

Stop disc play.•

u (Play/Pause)

Start, pause or resume disc play.•

INFO

For disc, display the current status or • disc information.

For slideshows, display a thumbnail view • of photo ﬁ les.

Conﬁ rm an entry or selection.•

SETUP

Access or exit the setup menu.•

j ,

(USB)

Switch to USB mode and display the • content.

Numeric buttons

Select an item to play.•

SUBTITLE

Select DVD or DivX subtitle language.•

Access the menu to USB copy or USB • delete.

ZOOM

Fit the picture format to the TV screen.•

Zoom in or out of the picture.•

REPEAT

Toggle between various repeat modes.•

REPEAT A-B

Mark the section for repeat play; turn • off repeat mode.

3-1

Mechanical and Dismantling Instructions

Dismantling Instruction

The following guidelines show how to dismantle the player. Step1: Remove 5 screws around the Top Cover, and then remove the Top Cover (Figure 1).

Detailed information please refer to the model set.

Figure 1

Step2: If it is necessary to dismantle Loader or Front Panel, the Front door should be removed first. (Figure 2) Note: Make sure to operate gently otherwise the guider would be damaged.

Please kindly note that dismantle the front door

assembly carefully to avoid damage tray and the front door.

Figure 2

3-2

XP2

XP3

XP4

XP5

XP1

XP7

XP6

SNAP

Mechanical and Dismantling Instructions

Dismantling Instruction

Step3: If the tray can’t open in normal way, you can make it through the instruction as below (Figure 3).

Note: Make sure to operate gently otherwise the guider would be damaged.

Detailed information please refer to the model set.

Step4: Dismantling Front Panel, disconnect the connectors (XP5, XP6. XP7), need release 4 snaps of Front Panel

and 2 snaps of bottom cabinet , then gently pull the Panel out from the set. (Figure 4 - Figure 6)

Figure 3

Figure 4

3-3

Mechanical and Dismantling Instructions

Dismantling Instruction

Detailed information please refer to the model set.

Figure 5

Step5: Dismantling Loader, disconnect the 3 connectors (XP2, XP3, XP4) aiming in the below figure, and remove 1 screw that

connects the loader and the bottom cabinet. (Figure 5 & 6)

Figure 6

3-4

Mechanical and Dismantling Instructions

Dismantling Instruction

Step6: Dismantling Main Board, first disconnect the connector (XP1), and then remove 5 screws. (Figure 7)

Step7: Remove the 2 screws on Power Board to dismantle the Power Board. (Figure 7)

Detailed information please refer to the model set.

Figure 7

Software upgrade

4-1

Preparation to upgrade software

1) Start the CD Burning software and create a new CD

project (Data Disc) with the following setting:

Label: DVP3XXX (No need the label name)

File Name: DVPXX

Power on the set and open the tray, then press <5><5>

to check the File Name.

Note: It is required capital letter for the File System

name.

2) Burn the data onto a blank CDR

A. Procedure for software upgrade:

1) Power on the set and insert the prepared Upgrade

CDR.

2) The set will starts reading disc & response with the

following display TV screen:

Upgrade File DETECTED

Upgrade?

Press Play TO START.

3) Press <OK> button to confirm, then screen will display :

Files coping…

UPGRADING…

4) The upgraded tray will automatically open when files

coping complete, then take out the disc.

5) About 1 minute later, the trace will automatically close

when upgrading complete.

XX(K)_XX.BIN

B. Read out the software versions to confirm upgrading

1) Power on the set and press <Setup> button on the remote control.

2) Press<1><3><7><9> button or press down cursor on remote control to choose "Preference" and press right & down cursors to choose "Version Info".

The software version and other information are display

on the TV screen as follows:

Model DVP33X File Name DVP33X Version XX.XX.XX.XX RISC XX.XX.XX.XX Servo XX.XX.XX.XX Region Code X HDCP PASS(except press<1><3><7><9>)

* The other upgrade SW way is by memory, the steps are the

same as CDR's, create the upgrade file into memory, and connect the USB flash drive to the USB socket on set, then press "USB" on remote control to access the content and play the upgrade file as above upgrade procedure.

X(K) XX X(K) XX.BIN

Caution: The set must not be power off during

upgrading, Otherwise the Main board will be

damaged entirely.

Region Code Change

1) Power on the set and open the tray door;

2) Press the "Setup" button on the remote control,then the setup interface should be displayed on the TV screen;

3) Move the down cursor on remote control to choose "Reference"

and press "1" "3" "8" "9" "3" "1" on the remote control;

4) Then move the up or down cursors to choose the region code.

Note: restart after above steps.

+ 32 hidden pages