Page 1
Register your product and get support at
www.philips.com/welcome
DVP3350K
EN User manual
ZH_CN
Ⴌ߀൱Ҭ
Page 2
2
Page 3
Contents
1 Important 4
Safety and important notice 4
Trademark Notice 5
6 Advanced features 24
Media copy 24
Create MP3 les 24
7 Adjust sound 26
Karaoke settings 26
Turn off vocal (cancel voice) 26
English
Contents
2 Your DVD player 6
Features highlight 6
Product overview 7
3 Connect 9
Connect video cables 9
Connect audio cables 10
Route audio to other devices 10
Connect USB device 11
Connect to power outlet 11
4 Get started 12
Prepare the remote control 12
Find the correct viewing channel 13
Select menu display language 13
Turn on Progressive Scan 14
8 Adjust settings 27
General setup 27
Audio setup 28
Video setup 30
Preferences 32
9 Additional information 34
Update software 34
Care 34
10 Speci cation 35
11 Troubleshooting 36
12 Glossary 38
5 Play 15
Play from disc 15
Play video 16
Play music 20
Play photo 21
Play from USB device 23
EN 3
Page 4
1 Important
Safety and important notice
Warning
•
Risk of overheating! Never install the DVD player
in a con ned space. Always leave a space of at least
four inches around the DVD player for ventilation.
Ensure the curtains or other objects never cover the
ventilation slots on the DVD player.
•
Never place the DVD player, remote control or
batteries near naked ames or other heat sources,
including direct sunlight.
•
Only use this DVD player indoors. Keep this DVD
player away from water, moisture and liquid- lled
objects.
Never place this DVD player on other electrical
•
equipment.
Keep away from this DVD player during lightning
•
storms.
Where the mains plug or an appliance coupler is
•
used as the disconnect device, the disconnect device
shall remain readily operable.
•
Visible and invisible laser radiation when open. Avoid
exposure to beam.
About Progressive Scan
Consumers should note that not all high
de nition television sets are fully compatible
with this product and may cause artifacts to be
displayed in the picture. In case of 525 or 625
progressive scan picture problems, it is
recommended that the user switch the
connection to the ‘standard de nition’ output. If
there are questions regarding our TV set
compatibility with this model 525p and 625p
DVD player, please contact our customer
service center.
Recycle notice
This electronic equipment contains a large
number of materials that can be recycled or
reused if disassembled by a specialized
company. If you are disposing of an old
machine, please take it to a recycling center.
Please observe the local regulations regarding
disposal of packaging materials, exhausted
batteries and old equipment.
Copyright notice
This product incorporates copyright protection
technology that is protected by method claims
of certain U.S. patents and other intellectual
property rights owned by Macrovision
Corporation and other rights owners. Use of
this copyright protection technology must be
authorized by Macrovision Corporation, and is
intended for home and other limited viewing
uses only unless otherwise authorized by
Macrovision Corporation. Reverse engineering
or disassembly is prohibited.
4 EN
Page 5
Trademark Notice
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are registered trademarks of Dolby Laboratories.
Windows Media and the Windows logo are
trademarks, or registered trademarks of
Microsoft Corporation in the United States and/
or other countries.
English
Important
DivX, DivX Certi ed, and associated logos are
trademarks of DivX, Inc. and are used under
license.
Plays DivX
audio tracks.
The USB-IF Logos are trademarks of Universal
Serial Bus Implementers Forum, Inc.
®
video with menus, subtitles and
EN 5
Page 6
2 Your DVD
ALL
player
Create MP3 les
Convert your favorite audio tracks from an
audio CD into MP3 format. The created MP3
les are saved in your USB ash drive.
Congratulations on your purchase, and
welcome to Philips! To fully bene t from the
support that Philips offers, register your product
at www.philips.com/welcome.
This DVD player brings audio and video to life.
Just plays practically any disc format, including
the digital photos with absolutely no
compromise to picture quality.
Features highlight
Screen t
View the movie in full screen on any TV with
this DVD player.
Karaoke scoring function
Karaoke scoring gives a score for each
performance. Have your singing performance
scored for even more karaoke fun at home!
Region codes
Your DVD player plays discs with the following
region codes.
DVD region code Countries
China
Progressive scan component video
Pushes the limits of standard resolution and
provides a more lm-like image display that is
more pleasing for viewing DVDs on a TV
display.
Hi speed USB 2.0 link
Simply plug your USB ash drive into the USB
jack to play your MP3/WMA/JPEG/DivX les to
enjoy the music play in superb sound quality.
Media copy
You can transfer data les such as MP3, WMA
and JPEG from disc to USB ash drive.
6 EN
Page 7
Product overview
Remote control
English
Main unit
a (Standby-on)
Turn on the DVD player or switch to •
standby mode.
b Disc compartment
c Display panel
1
2
3
4
5
31 2
5
4
7
6
6
7
8
9
10
18
17
16
15
14
13
12
11
Your DVD player
d Z (Open/Close)
Open or close the disc compartment.•
e u (Play/Pause)
Start, pause or resume disc play.•
f (USB) jack
Connect a USB ash drive.•
g MIC
Audio input from a microphone.•
a (Standby-On)
Turn on the DVD player or switch to •
standby mode.
b Z (Open/Close)
Open or close the disc compartment.•
c DISC MENU
Access or exit the disc menu.•
Switch to disc mode.•
For VCD/SVCD, turn PBC (Playback •
Control) on or off in PBC mode.
EN 7
Page 8
d v V b B (Navigation buttons)
m AUDIO/CREATE MP3
Navigate through the menus.•
Search fast-forward (• B) or fast-
backward (b). Press repeatedly to
change the search speed.
Search slow-forward (• v) or slowbackward (V). Press repeatedly to
change the search speed.
e 2 BACK
Return to the previous display menu.•
For DVD, navigate to the title menu.•
For VCD version 2.0 or SVCD with •
PBC turned on, return to the menu.
f Ó/Ñ (Previous/Next)
Skip to the previous or next title, •
chapter, or track.
Press and hold for fast-backward or •
fast-forward search.
Select an audio language/channel.•
Access the menu to create MP3.•
n x (Stop)
Stop disc play.•
o u (Play/Pause)
Start, pause or resume disc play.•
p INFO
For disc, display the current status or •
disc information.
For slideshows, display a thumbnail view •
of photo les.
q OK
Con rm an entry or selection.•
r SETUP
Access or exit the setup menu.•
g (USB)
Switch to USB mode and display the •
content.
h Numeric buttons
Select an item to play.•
i SUBTITLE
Select DVD or DivX subtitle language.•
Access the menu to USB copy or USB •
delete.
j , ZOOM
Fit the picture format to the TV screen.•
Zoom in or out of the picture.•
k VOCAL
Change the audio channel of a karaoke •
disc.
l KARAOKE
Access or exit the karaoke menu.•
8 EN
Page 9
3 Connect
Note
Make the following basic connections to use the
DVD player.
Basic connections:
Video cables•
Audio cables•
Optional connections:
Audio to other devices:•
Digital ampli er/receiver•
Analog stereo system•
Note
Refer to the type plate at the rear or bottom of the •
product for identi cation and supply ratings.
Before you make or change any connections, ensure
•
that all the devices are disconnected from the power
outlet.
You must connect this DVD player directly to a TV.•
Option 1: Connect to component
video jacks
Pb
Pr
Y
COMPONENT VIDEO OUT
Pr
COMPONENT
Pb
VIDEO IN
Y
1 Connect the component video cables (not
supplied) to the Y Pb Pr jacks on this DVD
player and the component video input
jacks on the TV.
English
Connect
Tip
Different types of connectors may be used to •
connect this product to your TV, depending on
availability and your needs. A comprehensive
interactive guide to help you connect your product is
available at www.connectivityguide.philips.com.
Connect video cables
Connect this DVD player to the TV to view
disc play.
Select the best video connection that the TV can
support.
Option 1:• Connect to component video
jacks (for a standard TV or Progressive Scan
TV).
Option 2:• Connect to video (CVBS) jack
(for a standard TV).
If a progressive scan TV is used, you •
may turn on the progressive scan mode
(see chapter ‘Turn on Progressive Scan’
for details).
Tip
The component video input jacks on the TV may be •
labeled as Y Pb/Cb Pr/Cr or YUV.
This type of connection provides good picture
•
quality.
EN 9
Page 10
Option 2: Connect to video (CVBS)
jack
VIDEO IN
Route audio to other devices
Route the sound from this DVD player to other
devices to enhance audio play.
Connect to digital ampli er/receiver
1 Connect a composite video cable
(supplied) to the TV OUT jack on this
DVD player and the video input jack on
the TV.
Tip
The video input jack on the TV may be labeled as •
A/ V IN, VIDEO IN, COMPOSITE or BASEBAND.
This type of connection provides standard picture
•
quality.
Connect audio cables
Connect the audio from this DVD player to the
TV to allow sound output through the TV.
DIGITAL IN
DIGITAL
OUT
COAXIAL
1 Connect a coaxial cable (not supplied) to
the COAXIAL/DIGITAL OUT jack on this
DVD player and the COAXIAL/DIGITAL
input jack on the device.
Tip
You can optimize the audio output (see chapter •
‘Adjust settings’ - [ Audio Setup ] > [ Digital Audio
]) for details.
AUDIO IN
1 Connect the audio cables (supplied) to the
AUDIO OUT L/R jacks on this DVD
player and the audio input jacks on the TV.
10 EN
Page 11
Connect to analog stereo system
Connect USB device
AUDIO IN
1243690612436906
1 Connect the audio cables (supplied) to the
AUDIO OUT L/R jacks on this DVD
player and the audio input jacks on the
device.
Tip
You can optimize the audio output (see chapter •
‘Adjust settings’ - [ Audio Setup ] > [ Analog Output
]) for details.
1 Connect the USB ash drive to the
(USB) jack on this DVD player.
Note
This DVD player can only play/view MP3, WMA, •
DivX or JPEG les that are stored on such devices.
Press
• to access the content and play the les.
English
Connect
Connect to power outlet
Warning
Risk of product damage! Ensure that the power •
supply voltage corresponds to the voltage printed on
the back or the underside of the DVD player
1 Connect the power cord to the power
outlet.
The DVD player is ready to be set up
for use.
EN 11
Page 12
4 Get started
Prepare the remote control
Navigate through the menu
1 Point the remote control directly at the
remote sensor on this DVD player and
select the desired function.
1 Push to open the battery compartment
cover.
2 Insert two R03 or AAA type batteries with
correct polarity (/) as indicated.
3 Close the battery compartment.
Caution
Remove batteries if they are exhausted or if the •
remote control is not to be used for a long time.
Do not mix batteries (old and new or carbon and
•
alkaline, etc.).
Batteries contain chemical substances. They should
•
be disposed off properly.
2 Use the following buttons on the remote
control to navigate through the on-screen
menus.
Button Action
v V
b B
OK
Move up or down.
Move left or right.
Con rm a selection.
Enter numbers.
12 EN
Page 13
Find the correct viewing
channel
Press to turn on the DVD player.
1
Select menu display language
Press SETUP.
1
[ General Setup ] menu is displayed.
English
2 Turn on the TV and switch to the correct
video-in channel.
You may go to the lowest channel on •
the TV, then press the Channel Down
button on the TV remote control until
you see the Video In channel.
You may press • button repeatedly
on the TV remote control.
Usually, this channel is between the •
lowest and highest channels and may
be called FRONT, A/V IN, VIDEO, etc..
Tip
See the TV user manual on how to select the correct •
input on the TV.
•
If the audio output of this DVD player is routed
to other audio device (such as audio system
or receiver), turn on the audio device to the
appropriate audio input channel. Refer to the device
user manual for details.
2 Select [ OSD Language ], then press B.
General Setup
Disc Lock
OSD Language
Sleep Timer
Auto Standby
DivX(R) VOD Code
English
The language options are different •
depending on your country or region.
It may not correspond to the illustration
shown here.
3 Press vV to select a language, then press
OK.
Tip
Get started
You can set the default language for DVD audio •
and disc menu, see chapter ‘Adjust settings’ - [
Preferences ] for details.
EN 13
Page 14
Turn on Progressive Scan
Connect a progressive scan TV with
component video jacks (see chapter ‘Connect
video cables - Option 1: Connect to
component video jacks’ for details).
1 Turn on the TV to the correct viewing
channel for this DVD player.
2 Press SETUP.
3 Press V to select [ Video Setup ].
7 You can now turn on the progressive scan
mode on the TV (see the TV user manual).
Note
During play, when progressive scan mode is on for •
both this DVD player and the TV, distorted picture
may display. Turn off the progressive scan feature on
both this DVD player and the TV.
4 Select [ Progressive ] > [ On ]
OK.
A warning message is displayed.
Video Setup
TV System
TV Display
Progressive
Picture Setting
On
Off
then press
,
5 To proceed, select [ OK ] and press OK.
The progressive setup is complete.
Note
If a blank /distorted screen is displayed, wait for 15 •
seconds for the auto recover.
•
If no picture is displayed, turn off the progressive
scan mode as follows:
1) Press Z to open the disc compartment.
2) Press the numeric button ‘1’.
6 To exit the menu, press SETUP.
14 EN
Page 15
5 Play
Play from disc
Note
DVDs and DVD players are designed with regional •
restrictions. Ensure that the DVD video you play is
for the same region zone as the player (indicated on
its back).
This DVD player can support play of the following
•
le formats: MP3/WMA/JPEG/DivX.
•
To play DVD-R , DVD+R or DVD-RW, the disc must
be nalized.
Tip
If the password entry menu is displayed, you have to •
enter the password before it can be played.
•
If you pause or stop a disc for about 5 minutes, the
screen saver activates. To deactivate the screen
saver, press DISC MENU.
•
After you pause or stop a disc, if no buttons
are pressed within 15 minutes, this DVD player
automatically switches to standby mode.
English
Play
Play a disc
Caution
Never place any objects other than discs into the •
disc compartment.
1 Press Z to open the disc compartment.
2 Insert a disc with its label facing up.
For double-sided disc, load the side to •
play faces up.
3 Press Z to close the disc compartment
and start disc play.
To view disc play, turn on the TV to •
the correct viewing channel for this
DVD player.
4 To stop disc play, press x.
EN 15
Page 16
Play video
Change video play
Note
For video disc, play always resumes from the point •
where it was last stopped. To star t play from the
beginning, press
Ó while the message is displayed.
Control a title
1 Play a title.
2 Use the remote control to control the title.
Button Action
u
x
Ñ
Ó
m
, M Searches fast-forward (M)
v
, V Searches slow-forward (v) or
Start, pause or resume disc
play.
Stop disc play.
Skip to the next title or
chapter.
Skip to the beginning of the
current title or chapter.
Press twice to jump to the •
previous title or chapter.
or fast-backward (m).
Press repeatedly to change •
the search speed.
slow-backward (V).
1 Play a title.
2 Use the remote control to change the
video play.
Button Action
AUDIO/
CREATE MP3
SUBTITLE
, ZOOM
(Screen Fit)
, ZOOM
INFO
Change audio language.
Only applicable to discs •
with multiple audio
language or channel.
Change subtitle language.
Only applicable to discs •
with multiple subtitle
language.
Fit the picture format to the
TV screen.
Press repeatedly until the •
image is scaled to t to
the TV screen.
Toggle between screen
aspect ratio and different
zoom factor.
To pan through the •
zoomed image, press the
navigation buttons.
Display the current status or
disc information.
You can change the video •
play options here without
interrupting disc play.
16 EN
Press repeatedly to change •
the search speed.
For VCD/SVCD, slow-•
backward search is not
possible.
Note
Some operations may not work with some discs. See
•
the information accompanying the disc for details.
.
Page 17
Access DVD menu
Preview disc contents
English
Play
1 Press DISC MENU to access disc main
menu.
2 Select a play option, then press OK.
In some menus, press the • numeric
buttons to input your selection.
To return to the title menu during play, •
press 2 BACK.
Access VCD menu
The PBC (Playback Control) for VCD/SVCD is
turned on by default in the factory. When you
load in a VCD/SVCD, the contents menu is
displayed.
1 Press numeric buttons to select a play
option, then press OK to start play.
If PBC is off, it skips the menu and starts •
play from the rst track.
During play, you can press • 2 BACK to
return to the menu (if the PBC mode is
on).
Tip
The default setting for PBC is on. You can change the •
default setting, see chapter ‘Adjust settings’ -
[ Preferences ] > [ PBC ] for details.
1 During play, press INFO.
The disc status menu is displayed.
2 Select [ Preview ], then press B.
DVD
Select Digest Type:
Title Digest
Chapter Digest
Title Interval
Chapter Interval
VCD/SVCD
Select Digest Type:
Track Digest
Disc Interval
Track Interval
3 Select a preview option, then press OK.
A six thumbnails preview screen is
displayed.
To go to the next/previous preview •
screen, press Ó/Ñ.
To start play, press • OK at the selected
thumbnail picture.
EN 17
Page 18
Quick skip play to a speci c time
View DVD play from different angles
1 During play, press INFO.
The disc status menu is displayed.
2 Select the current elapsed playing time,
then press B.
[ TT Time ]• (title time)
[ CH Time ] • (chapter time)
[ Disc Time ] • (disc time)
[ Track Time ] • (track time)
3 Press the numeric buttons to change the
time where you want to skip to.
Display play time
1 During play, press INFO.
The disc status menu is displayed.
2 Select [ Time Disp ], then press B.
The display options are different
depending on the disc type.
Option Action
1 During play, press INFO.
The disc status menu is displayed.
2 Select [ Angle ], then press B.
3 Press the numeric buttons to change the
angle.
Play changes to the selected angle.
Note
Only applicable to discs contain sequences recorded •
from different camera angles.
Repeat play - video
For DVD/VCD/SVCD
1 During play, press INFO.
The disc status menu is displayed.
2 Select [ Repeat ] in the menu, then press
B.
[ Title Elapsed ]
/ [ Chapter
Elapsed ]
[ Title Remain ]
/ [Chapter
Remain ]
[ Total Elapsed
] / [Single
Elapsed ]
[ Total Remain
] / [Single
Remain ]
Display DVD title or chapter
elapsed play time.
Display DVD title or chapter
remaining play time
Display VCD/SVCD disc or
track elapsed play time.
Display VCD/SVCD disc or
track remaining play time.
3 Select an option, then press OK.
3 Press vV to select a repeat option, then
press OK.
Note
For VCD/SVCD, repeat play is only possible if PBC •
mode is turned off.
18 EN
Page 19
Set repeat play for a speci c section
Play DivX® video
1 During play, press INFO.
The disc status menu is displayed.
2 Select [ Repeat AB ] in the menu, then
press OK at the start point.
3 Press OK again to set the end point.
Repeat play starts.
4 To cancel repeat play, press OK again.
Note
The marked section for repeat play is only possible •
within a title or track.
DivX video is a digital media format that retains
high quality despite a high rate of compression.
This DVD player is DivX® Certi ed so that
you can enjoy DivX video.
1 Insert a disc or USB that contains the DivX
videos.
For USB, press •
A contents menu is displayed.
.
2 Select a title to play, then press OK.
3 Use the remote control to control the
title.
Button Action
SUBTITLE
AUDIO/
CREATE MP3
Changes subtitle language.
Changes audio language/
channel.
English
Play
x
INFO
Note
You can only play DivX videos that were rented or •
purchased with the DivX registration code of this
DVD player (see chapter ‘Adjust settings’ - [ General
Setup ] > [ DivX(R) VOD Code ] for details).
•
If the subtitle does not appear correctly, change the
subtitle language (see chapter ‘Adjust settings’ [ Preferences ] > [ DivX Subtitle ] for details).
Stops disc play.
The contents menu is •
displayed.
Display title elapsed play
time or title remaining play
time.
EN 19
Page 20
Play music
Quick skip play
Note
For some commercial audio disc, play may resume •
from the point where it was last stopped. To star t
play from rst track, press
Ó.
Control a track
1 Play a track.
2 Use the remote control to control the
track.
Button Action
u
x
Start, pause or resume disc
play.
Stop disc play.
1 During play, press INFO until one of
the following options is selected.
Display Action
[ Disc Go
To ]
[ Track Go
To ]
[ Select
Track ]
Skip play to a speci c time
within the disc.
Skip play to a speci c time
within a track
Skip play to a speci c track
number.
2 Press the numeric buttons to change the
time/number where you want to skip to.
Repeat play - audio
Ñ
Ó
m
, M Searches fast-forward (M)
Skip to the next track.
Skip to the beginning of the
current track. Press twice to
jump to the previous track.
Select an item to play.
or fast-backward (m).
Press repeatedly to change •
the search speed.
For audio CD
1 During play, press INFO repeatedly
until [ Off ] is selected.
2 Press b B to select a repeat option.
For MP3/WMA les
1 During play, press INFO to select a
repeat option.
20 EN
Page 21
Play MP3/WMA music
MP3/WMA is a type of highly compressed
audio le ( les with .mp3, .wma extensions).
Play photo
English
1 Insert a disc or USB that contains the MP3/
WMA music.
For USB, press •
A contents menu is displayed.
Play starts.
.
2 Select a track to play if play does not start
automatically.
To select another track/folder, press •
vV, then press OK.
3 To return to the main menu, press v until
the root menu is selected, then press OK.
Note
For CDs recorded in multiple sessions, only the rst •
session is played.
This DVD player does not suppor t MP3PRO audio
•
format.
If any special characters are present in the MP3
•
track name (ID3) or album name, it may not display
correctly on the screen because these characters are
not supported.
•
Some WMA is protected by Digital Rights
Management (DRM), it cannot be played on this
DVD player.
Folders/ les exceed the supported limit of this DVD
•
player are not displayed or played.
Play photos as slideshow
This DVD player can play JPEG photos ( les
with .jpeg or .jpg extensions).
1 Insert a disc or USB that contains the JPEG
photos.
For USB, press •
For a Kodak disc, the slideshow begins
automatically.
For a JPEG disc, the photo menu is
displayed.
.
2 Select the folder/album you want to play.
To preview the photos in the folder/•
album, press
INFO.
Play
Tip
You can display the data disc contents without •
folders, see chapter ‘Adjust settings’ - [ Preferences ]
> [ Mp3/Jpeg Nav ] for details.
To go to previous or next screen •
display, press Ó/Ñ.
To select a photo, press the • navigation
buttons.
To display the selected photo only, •
press OK.
3 Press OK to start slideshow play.
To return to the menu, press • 2 BACK.
EN 21
Page 22
Note
Play musical slideshow
You may require longer time to display the disc •
content on the TV due to the large number of songs/
photos compiled onto one disc.
•
If the JPEG photo is not recorded with an ‘exif’ type
le, the actual thumbnail picture is not be shown
on the display. It is replaced by a ‘blue mountain’
thumbnail picture.
•
This DVD player can only display digital camera
pictures according to the JPEG -EXIF format, typically
used by almost all digital cameras. It cannot display
Motion JPEG and pictures in formats other than
JPEG, or sound clips associated with pictures.
•
Folders/ les exceed the supported limit of this DVD
player are not displayed or played.
Control photo play
1 Play photo slideshow.
2 Use the remote control to control the
photo.
Play MP3/WMA music les and JPEG photo
les simultaneously to create musical slideshow.
The MP3/WMA and JPEG les must be stored
on the same disc.
1 Play MP3/WMA music.
2 Navigate to the photo folder/album and
press OK to start slideshow play.
Slideshow begins and continues till the
end of the photo folder or album.
Audio continues to play till the end of
the disc.
To return to the menu, press • 2 BACK.
3 To stop slideshow play, press x.
4 To stop music play, press x again.
Button Action
b
B
v
V
, ZOOM
x
Rotate the photo anticlockwise.
Rotate the photo clockwise.
Flip the photo vertically.
Flip the photo horizontally.
Zoom in/ out.
Play pause in zoom mode.•
Stop disc play.
22 EN
Page 23
Play from USB device
This DVD player plays/views MP3, WMA, DivX
or JPEG les that are stored on USB device.
1 Connect a USB ash drive to the
(USB) jack on this DVD player.
2 Press .
A contents menu is displayed.
Play starts.
English
Play
3 Select a le to play if play does not start
automatically.
For more information, see chapters •
‘Play music, Play photo, Play video’ for
details.
4 To stop play, press x or remove the USB
device.
To switch to the disc mode, press •
or DISC MENU.
Tip
If the device does not t into the USB jack, connect it •
through a USB extension cable.
•
Digital cameras that require additional programme
installation when connected to a PC are not
supported.
EN 23
Page 24
6 Advanced
features
Media copy
You can transfer data les such as MP3, WMA
or JPEG from disc to the USB device.
Note
While you copy, never press any buttons. •
Copy-protected media cannot be copied. •
Create MP3 les
You can convert audio CDs into MP3 audio
les with this DVD player. The created MP3
audio les are saved in the USB device.
1 Insert a disc that contains the MP3/WMA/
JPEG les.
2 Press x to stop disc play.
3 Connect the USB ash drive to the
(USB) jack on this DVD player.
4 Select the le to copy, then press
SUBTITLE.
5 Select [ Yes ] in the menu to start to copy,
then press OK.
00:00/00:00 005/030
\MP3
Previous
Track 1
Track 2
Track 3
Track 4
Track 5
Track 6
Track 7
Do you want
to copy this file
Yes No
1 Insert an audio CD.
2 Connect the USB ash drive to (USB)
jack on this DVD player.
3 During disc play, press AUDIO/CREATE
MP3.
4 Select [ Yes ] in the menu and press OK.
Create MP3
OPTIONS
Speed Normal
Bitrate 128kbps
CRT ID3 Yes
Device USB 1
Summary
Press [OK] button
to change speed.
Start Exit
TRACK
Track01 04:14
Track02 04:17
Track03 03:58
Track04 04:51
Track05 03:53
Track06 04:09
Track07 04:38
Select all
Deselect all
5 Select the conversion options in the
[ OPTIONS ] panel and press OK.
Once complete, a new folder is created
automatically in the USB device to store
all the new data les.
6 To stop copy progress, press x, then
press OK.
24 EN
Page 25
Option Description
[ Speed ]
[ Bitrate ]
[ CRT ID3 ]
[ Device ]
Select the write-to- le speed.
If • [ Normal ] speed is
selected, music play can be
heard while creating the
MP3 le.
Select the quality level.
Higher bitrate for better sound
quality and bigger le size.
Default setting is • [ 128
kbps ].
Copy track information into
the MP3 le.
Default setting is • [ Yes ].
The created MP3 les can
only be saved in USB device.
6 Press B to access the [ TRACK ] panel.
English
Advanced features
7 Select the audio track, then press OK.
To select another track, repeat step 7.•
To select all tracks, select • [ Select all ]
in the menu and press OK.
To deselect all tracks, select • [ Deselect
all ] in the menu and press OK.
8 Select [ Start ] in the menu to start to
convert, then press OK.
Once complete, a new folder is created
automatically in the USB device to store
all the new MP3 les.
To exit the menu, select • [ Exit ] and
press OK.
Note
While you convert, never press any buttons. •
DTS CDs and copy-protected CDs cannot be •
conver ted.
•
Write-protected or password-protected USB
devices cannot be used to store MP3 les.
EN 25
Page 26
7 Adjust sound
Karaoke settings
[ Karaoke Scoring ]: Select a karaoke rating
score level.
[ Off ]• – no score rating display.
[ Basic ]• – basic rating.
[ Intermediate ]• – intermediate rating.
[ Advance ]• – advance rating.
1 Turn on the TV to the correct viewing
channel for this DVD player.
2 Connect a microphone (not supplied) to
MIC jack on this DVD player.
3 Press KARAOKE repeatedly to access
various setting options.
Note
A karaoke score is displayed at the end of the song. •
Press OK to exit and resume karaoke session.
•
Karaoke score function is only available for DVD and
VCD discs.
Set the microphone volume to the minimum level
•
before connecting the microphone to prevent
howling.
Turn off vocal (cancel voice)
[ MIC ]: Press b B to turn on or off
microphone output.
[ Vol ]: Press b B to set the microphone
volume level.
[ Echo ]: Press b B to set the echo level.
[ Key ]: Press b B to set the pitch level that
match your voice.
1 Press VOCAL repeatedly to toggle
through various audio modes or turn off
the vocal.
Note
You cannot cancel the voice output from MP3 discs.•
26 EN
Page 27
8 Adjust settings
This section describes the various setting
options of this DVD player.
4 Select a setting, then press OK.
To return to the previous menu, press •
b.
To exit the menu, press • SETUP.
English
Symbol Option
[ General Setup ]
[ Audio Setup ]
[ Video Setup ]
[ Preferences ]
Note
If the setup option is grayed out, it means the setting •
cannot be changed at the current state.
Note
See the explanations of the above options in the •
following pages.
[ Disc Lock ]
Set play restriction for a speci c discs.
Before you start, place the disc in the disc
compartment (maximum 20 discs can be
locked).
[ Lock ] • – restrict access to the current
disc. The next time you want to play
this disc or unlock it, you need to enter
the password.
[ Unlock ]• – play all discs.
Tip
To set or change the password, go to •
[ Preferences ] > [ Password ].
Adjust settings
General setup
Press SETUP.
1
[ General Setup ] menu is displayed.
2 Press B.
3 Select an option, then press OK.
General Setup
Disc Lock
OSD Language
Sleep Timer
Auto Standby
DivX(R) VOD Code
[ OSD Language ]
Select the default on-screen menu
language.
[ Sleep Timer ]
Switch to standby automatically after the
preset time.
[ Off ]• – disable sleep mode.
[ 15 Mins ], [ 30 Mins ], •
[ 45 Mins ], [ 60 Mins ] – select the
count down time before the DVD
player switches to standby.
EN 27
Page 28
[ Auto Standby ]
Turn off or on automatic standby switching
mode. It is an energy saving feature.
[ On ]• – switch to standby after 15
minutes of inactivity (for example, in
pause or stop mode).
[ Off ]• – disable auto standby mode.
Audio setup
Press SETUP.
1
[ General Setup ] menu is displayed.
2 Press V to select [ Audio Setup ], then
press B.
[ DivX(R) VOD Code ]
Display the DivX® registration code.
Tip
Enter this DVD player’s DivX registration code when •
you rent or purchase video from www.divx.com/vod.
The DivX videos rented or purchased through the
DivX® VOD (Video On Demand) service can be
played only on the device to which it is registered.
3 Select an option, then press OK.
Audio Setup
Analog Output
Digital Audio
Volume
Sound Mode
CD Upsampling
Night Mode
4 Select a setting, then press OK.
To return to the previous menu, press •
b.
To exit the menu, press • SETUP.
Note
See the explanations of the above options in the •
following pages.
28 EN
Page 29
[ Analog Output ]
[ Volume ]
Select the analog audio setting based on
the audio device that is connected through
the analog audio jack.
[ Stereo ]• – for stereo output.
[ LT/RT ]• – for surround sound output
through two speakers.
[ Digital Audio ]
Select the setting based on the digital
ampli er/receiver that is connected
through the digital jack.
[ Digital Output ]• – select the type of
digital output.
Option Description
[ Off ] Disable digital output.
[ All ] The device supports
multi-channel audio
formats.
[ PCM Only ] The device is not capable
of decoding multi-channel
audio. Audio is
downmixed to twochannel sound: see
LPCM Output ]
[
setting.
Set the default volume level when you play
a disc.
Press 1. OK.
Press 2. b B to set the volume.
Press 3. OK to con rm and exit.
[ Sound Mode ]
Select a preset sound effect to enhance
the audio output.
[ 3D ]• – select a virtual surround sound
effect that is produced from the left and
right audio channels.
[ Movie Mode ]• – select a sound effect
for movies.
[ Music Mode ]• – select a sound effect
for music.
[ CD Upsampling ]
For better sound quality in stereo mode,
convert the music CD to a higher sampling
rate.
[ Off ]• – turn off CD-upsampling.
[ 88.2kHz ]• – convert to twice the
original sampling rate.
[ 176.4kHz ]• – convert to four times
the original sampling rate.
English
Adjust settings
[ LPCM Output ]• – select the LPCM
(Linear Pulse Code Modulation) output
sampling rate.
Option Description
[ 48kHz ] For discs recorded at
sampling rate of 48 kHz.
[ 96kHz ] For discs recorded at the
sampling rate of 96 kHz.
Note
[ LPCM Output ]• setting is only available if the
[ Digital Output ] is set to [ PCM only ].
The higher the sampling rate, the better the sound
•
quality.
EN 29
Page 30
[ Night Mode ]
You can play DVDs with Dolby Digital
mode at a low volume, without disturbing
others. High volume output is decreased
and low volume output is increased to an
audible level.
[ On ]• – turn on night mode.
[ Off• ] – enjoy surround sound with its
full dynamic range.
Video setup
Press SETUP.
1
[ General Setup ] menu is displayed.
2 Press V to select [ Video Setup ], then
press B.
3 Select an option, then press OK.
Video Setup
TV System
TV Display
Progressive
Picture Setting
4 Select a setting, then press OK.
To return to the previous menu, press •
b.
To exit the menu, press • SETUP.
Note
See the explanations of the above options in the •
following pages.
30 EN
Page 31
[ TV System ]
[ Picture Setting ]
If the video does not appear correctly,
change the setting. By default, this setting
matches the most common setting for TVs
in your country.
[ PAL ]• – for PAL-system TV.
[ Multi ]• – for TV that is compatible
with both PAL and NTSC.
[ NTSC ]• – for NTSC-system TV.
[ TV Display ]
Select the screen format according to how
you want the picture to appear on the TV.
4:3 Pan Scan (PS)
4:3 Letter Box (LB)
16:9 (Wide Screen)
Select a prede ned set of picture color
settings or customize the personal setting.
[ Standard ]• – original color setting.
[ Bright ]• – vibrant color setting.
[ Soft ]• – warm color setting.
[ Personal ]• – customize the color
setting. Set the level of brightness,
contrast, tint and color saturation, then
press OK.
English
Adjust settings
[ 4:3 Pan Scan ]• – for standard TV, a
full-height screen display with the sides
trimmed.
[ 4:3 Letter Box ]• – for standard TV, a
‘wide-screen’ display with black bars on
the top and bottom.
[ 16:9 ]• – for wide-screen TV (frame
ratio 16:9).
[ Progressive ]
If a progressive scan TV is connected to
the DVD player, turn on progressive scan
mode.
[ On ]• – turn on progressive scan
mode.
[ Off ]• – disable progressive scan mode.
Tip
There is more detailed description available. See •
chapter ‘Get Started - Turn on Progressive Scan’ for
details.
EN 31
Page 32
Preferences
Press SETUP.
1
[ General Setup ] menu is displayed.
2 Press V to select [ Preferences ] , then
press B.
[ Audio ]
Select the default audio language for
DVDs.
[ Subtitle ]
Select the default subtitle language for
DVDs.
3 Select an option, then press OK.
Preferences
Audio
Subtitle
Disc Menu
Parental Control
PBC
Mp3/Jpeg Nav
Password
DivX Subtitle
4 Select a setting, then press OK.
To return to the previous menu, press •
b.
To exit the menu, press • SETUP.
Note
[ Disc Menu ]
Select the menu language for DVDs.
Note
If the language you have set is not available on the •
disc, the disc uses its own default language.
For some DVDs, the subtitle/audio language can only
•
change from the disc menu.
To select the languages that are not listed in the
•
menu, select [ Others ]. Then check the Language
Code list at the back of this user manual and enter
the respective language code.
[ Parental Control ]
Restricts access to DVDs that are
unsuitable for children. These types of
DVDs must be recorded with ratings.
Press 1. OK.
Select a rating level, then press 2. OK.
Stop disc play before you can access to [Preferences].•
See the explanations of the above options in the •
following pages.
Press the 3. numeric buttons to enter
the password.
Note
Rated DVDs above the level you set in • [ Parental
Control ] require a password to be played.
•
The ratings are country-dependent. To allow all discs
to play, select ‘8’.
•
Some DVDs have ratings printed on them but are
not recorded with ratings. This function has no
effect on such DVDs.
Tip
You can set or change the password, go to•
[ Preferences ] > [ Password ].
32 EN
Page 33
[ PBC ]
[ DivX Subtitle ]
For VCDs/SVCDs recorded with PBC
(playback control), you can access the disc
content through an interactive menu.
[ On ]• – an index menu is displayed
when you load a disc for play.
[ Off ]• – skip the menu and start play
from the rst track.
[ Mp3/Jpeg Nav ]
Select to display the folders or display all
the les.
[ View Files ]• – display all the les.
[ View Folders ]• – display the folders of
MP3/WMA les.
[ Password ]
Follow the instructions on the TV to set or
change the password for locked discs and
play restricted DVDs.
Preferences
Change password
Old Password
New Password
Select a character set that supports the
DivX subtitle.
[ ]
Note
Ensure that the subtitle le has the exact same le •
name as the movie le. If for example the le name
of the movie is ‘Movie.avi’, then you will need to
name the text le ‘Movie.sub’ or ‘Movie.srt’.
Simpli ed Chinese
[ Version Info ]
Displays the software version of this DVD
player.
This information is required when you
want to nd out if the newest software
version is available at the Philips website
that you may download and install on this
DVD player.
[ Default ]
Resets all the settings of this DVD player
to factory default, except for [ Disc Lock ],
[ Parental Control ] and [ Password ]
settings.
English
Adjust settings
Confirm PWD
OK
Press the 1. numeric buttons to enter
‘136900’ or the last set password at [
Old Password ] eld.
Enter the new password at 2. [ New
Password ] eld.
Enter the new password again at 3.
[ Con rm PWD ] eld.
Press 4. OK to exit the menu.
Note
If you forget the password, enter ‘136900’ before •
you set a new password.
EN 33
Page 34
9 Additional
information
4 Visit www.philips.com/support to check for
the latest software version, using the le
name for this DVD player.
5 Refer to the upgrade instructions for more
information.
Note
Update software
To check for updates, compare the current
software version of this DVD player with the
latest software version (if available) at the
Philips website.
Caution
Power supply must not be interrupted during •
software upgrade.
1 Press SETUP.
Preferences
Disc Menu
Parental Control
PBC
Mp3/Jpeg Nav
Password
DivX Subtitle
Version Info
Default
Disconnect the power cord for a few seconds and •
connect again to reboot the system.
Care
Caution
Never use solvents such as benzene, thinner, •
cleaners available commercially, or anti-static sprays
intended for discs.
Clean discs
Wipe the disc with a micro bre cleaning cloth
from the center to the edge in a straight line
movement.
2 Select [ Preferences ] > [ Version Info ],
then press OK.
3 Write down the le name, then press
SETUP to exit the menu.
34 EN
Page 35
10 Speci cation
Note
Speci cation and design are subject to change •
without notice.
Accessories supplied
Remote control and batteries•
Audio/video cables•
Audio performance
DA converter: 24 bits, 192 kHz•
Frequency response: •
DVD: 4 Hz - 22 kHz (48 kHz); •
4 Hz - 44 kHz (96 kHz)
SVCD: 4 Hz - 20 kHz (44.1 kHz); •
4 Hz - 22 kHz (48 kHz)
CD/VCD: 4 Hz - 20 kHz (44.1 kHz) •
Signal-Noise (1 kHz): > 90 dB (A-weighted)•
Dynamic range (1 kHz): > 80 dB (A-weighted)•
Crosstalk (1 kHz): > 70 dB•
Distortion/noise (1 kHz): > 65 dB•
MPEG MP3: MPEG Audio L3•
English
Speci cation
Playback media
DVD-Video, Video CD/SVCD, Audio CD, CD-R/•
CD-RW, DVD+R/+RW, DVD-R/-RW, DivX-CD,
Picture CD, MP3-CD, WMA-CD, USB ash drive
USB
Compatibility: Hi-Speed USB (2.0)•
Class support: UMS (USB Mass Storage Class) •
TV standard
Number of lines: •
625 (PAL/50Hz); 525 (NTSC/60Hz)•
Playback: Multi-standard (PAL/NTSC)•
Video performance
Video DAC: 12 bits, 108 MHz•
Y Pb Pr: 0.7 Vpp ~ 75 ohm•
Video output: 1 Vpp ~ 75 ohm•
Video format
Digital compression: •
MPEG 2: DVD/SVCD •
MPEG 1: VCD/DivX•
Horizontal resolution: •
DVD: 720 pixels (50 Hz); 720 pixels (60 Hz) •
VCD: 352 pixels (50 Hz); 352 pixels (60 Hz) •
Vertical resolution: •
DVD: 576 lines (50 Hz); 480 lines (60 Hz) •
VCD: 288 lines (50 Hz); 240 lines (60 Hz) •
Audio format
Digital: •
MPEG/AC-3/PCM: Compressed digital (16, 20, 24 •
bits fs, 44.1, 48, 96 kHz)
MP3 (ISO 9660): 96, 112, 128, 256 kbps & •
variable bit rate fs, 32, 44.1, 48 kHz
Analog sound stereo•
Dolby surround compatible downmix from Dolby •
Digital multi-channel sound
Connections
Y Pb Pr output: Cinch 3x•
Video output: Cinch (yellow)•
Audio output (L+R): Cinch (white/red)•
Digital output: •
1 coaxial: IEC60958 for CDDA/LPCM; •
IEC61937 for MPEG 1/2, Dolby Digital
Main unit
Dimensions (w x h x d): 360 x 37 x 209 (mm)•
Net Weight: approximately 1.3 kg•
Power
Power supply rating: 110 V - 240V; 50/60 Hz•
Power consumption: < 10 W•
Power consumption in standby mode: < 1 W•
Laser Speci cation
Type: Semiconductor laser InGaAIP (DVD), AIGaAs •
(CD)
Wave length: 658 nm (DVD), 790 nm (CD)•
Output Power: 7.0 mW (DVD), 10.0 mW (VCD/CD)•
Beam divergence: 60 degrees•
EN 35
Page 36
11 Troubleshooting
Warning
If this happens when you turn on the •
progressive scan setting or change the TV
system setting, you have to switch to its
default mode:
Press 1. Z to open the disc compartment.
Risk of electric shock. Never remove the casing of •
this unit.
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
DVD player, check the following points before
requesting service. If the problem remains
unsolved, register your product and get support
at www.philips.com/welcome.
If you contact philips, you will be asked for the
model and serial number of your DVD player.
The model number and serial number are on
the back or bottom of your DVD player. Write
the numbers here:
Model No. __________________________
Serial No. ___________________________
Main unit
Press the 2. numeric button ‘1’ (for
progressive scan) or the numeric
button ‘3’ (for TV System).
Sound
No sound.
Ensure that the audio cables are connected •
and the connected device is turned on to
the correct input source.
No sound during DivX movies play.
The audio codec may not be supported by •
this DVD player.
Play
DivX video les cannot be played.
Ensure that the DivX video le is complete. •
Ensure that the le name extension is •
correct.
The buttons on this DVD player do not work.
Disconnect this DVD player from the •
power outlet for a few minutes, then
connect again.
Picture
No picture.
See TV manual for correct video input •
channel selection. Change the TV channel
until you see the DVD screen.
The aspect ratio of the screen is not aligned
with the TV display setting.
The aspect ratio is xed on the DVD.•
DivX subtitle are not displayed correctly.
Ensure that the subtitle le name is the •
same as the movie le name.
Select the correct character set.•
Press 1. SETUP.
Select 2. [ Preferences ] > [ DivX
Subtitle ] in the menu.
Select the character set that supports 3.
the subtitle.
36 EN
Page 37
The contents of the USB ash drive cannot be
read.
The USB ash drive format is not •
compatible with this DVD player.
Drive is formatted with different le system •
which is not supported by this DVD player
(e.g. NTFS).
English
Trouble s hooti n g
EN 37
Page 38
12 Glossary
A
Aspect ratio
Aspect ratio refers to the length to height ratio
of TV screens. The ratio of a standard TV is 4:3,
while the ratio of a high-de nition or wide TV is
16:9. The letter box allows you to enjoy a
picture with a wider perspective on a standard
4:3 screen.
D
DivX®
The DivX code is a patent-pending, MPEG-4
based video compression technology,
developed by DivX Networks, Inc., that can
shrink digital video to sizes small enough to be
transported over the internet, while maintaining
high visual quality.
M
MP3
A le format with a sound data compression
system. ‘MP3’ is the abbreviation of Motion
Picture Experts Group 1 (or MPEG-1) Audio
Layer3. By using the MP3 format, one CD-R or
CD-RW can contain about 10 times more data
than a regular CD. Files are recognized by their
le extension ‘.MP3’.
P
PBC
Playback Control. A system of navigating a
Video CD/Super VCD through on-screen
menus recorded onto the disc. You can enjoy
interactive play and searching.
Progressive Scan
The progressive scan displays twice the number
of frames per second than ordinary TV system.
It offers higher picture resolution and quality.
J
JPEG
A very common digital still picture format. A
still-picture data compression system proposed
by the Joint Photographic Expert Group, which
features small decrease in image quality in spite
of its high compression ratio. Files are
recognised by their le extension ‘JPG or JPEG’.
W
WMA
Windows Media™ Audio. Refers to an audio
compression technology developed by
Microsoft Corporation. WMA data can be
encoded by using Windows Media Player
version 9 or Windows Media Player for
Windows XP. Files are recognized by their le
extension ‘WMA’.
38 EN
Page 39
Language Code យᝆᅽᛞ
dvp3350K_93_bk_rc1.indd 35
4/14/2009 2:26:24 PM
Abkhazian 6566
Afar 6565
Afrikaans 6570
Amharic 6577
Arabic 6582
Armenian 7289
Assamese 6583
Avestan 6569
Aymara 6589
Azerhaijani 6590
Bahasa Melayu 7783
Bashkir 6665
Belarusian 6669
Bengali 6678
Bihari 6672
Bislama 6673
Bokmål, Norwegian 7866
Bosanski 6683
Brezhoneg 6682
Bulgarian 6671
Burmese 7789
Castellano, Español 6983
Catalán 6765
Chamorro 6772
Chechen 6769
Chewa; Chichewa; Nyanja 7889
9072
中文
Chuang; Zhuang 9065
Church Slavic; Slavonic 6785
Chuvash 6786
Corsican 6779
Česky 6783
Dansk 6865
Deutsch 6869
Dzongkha 6890
English 6978
Esperanto 6979
Estonian 6984
Euskara 6985
6976
Faroese 7079
Français 7082
Frysk 7089
Fijian 7074
Gaelic; Scottish Gaelic 7168
Gallegan 7176
Georgian 7565
Gikuyu; Kikuyu 7573
Guarani 7178
Gujarati 7185
Hausa 7265
Herero 7290
Hindi 7273
Hiri Motu 7279
Hrwatski 6779
Ido 7379
Interlingua (International)7365
Interlingue 7365
Inuktitut 7385
Inupiaq 7375
Irish 7165
Íslenska 7383
Italiano 7384
Ivrit 7269
Japanese 7465
Javanese 7486
Kalaallisut 7576
Kannada 7578
Kashmiri 7583
Kazakh 7575
Kernewek 7587
Khmer 7577
Kinyarwanda 8287
Kirghiz 7589
Komi 7586
Korean 7579
Kuanyama; Kwanyama 7574
Kurdish 7585
Lao 7679
Latina 7665
Latvian 7686
Letzeburgesch; 7666
Limburgan; Limburger 7673
Lingala 7678
Lithuanian 7684
Luxembourgish; 7666
Macedonian 7775
Malagasy 7771
Magyar 7285
Malayalam 7776
Maltese 7784
Manx 7186
Maori 7773
Marathi 7782
Marshallese 7772
Moldavian 7779
Mongolian 7778
Nauru 7865
Navaho; Navajo 7886
Ndebele, North 7868
Ndebele, South 7882
Ndonga 7871
Nederlands 7876
Nepali 7869
Norsk 7879
Northern Sami 8369
North Ndebele 7868
Norwegian Nynorsk; 7878
Occitan; Provencal 7967
Old Bulgarian; Old Slavonic 6785
Oriya 7982
Oromo 7977
Ossetian; Ossetic 7983
Pali 8073
Panjabi 8065
Persian 7065
Polski 8076
Português 8084
Pushto 8083
Russian 8285
Quechua 8185
Raeto-Romance 8277
Romanian 8279
Rundi 8278
Samoan 8377
Sango 8371
Sanskrit 8365
Sardinian 8367
Serbian 8382
Shona 8378
Shqip 8381
Sindhi 8368
Sinhalese 8373
Slovensky 8373
Slovenian 8376
Somali 8379
Sotho; Southern 8384
South Ndebele 7882
Sundanese 8385
Suomi 7073
Swahili 8387
Swati 8383
Svenska 8386
Tagalog 8476
Tahitian 8489
Tajik 8471
Tamil 8465
Tatar 8484
Telugu 8469
Thai 8472
Tibetan 6679
Tigrinya 8473
Tonga (Tonga Islands) 8479
Tsonga 8483
Tswana 8478
Türkçe 8482
Turkmen 8475
Twi 8487
Uighur 8571
Ukrainian 8575
Urdu 8582
Uzbek 8590
Vietnamese 8673
Volapuk 8679
Walloon 8765
Welsh 6789
Wolof 8779
Xhosa 8872
Yiddish 8973
Yoruba 8979
Zulu 9085
dvp3350K_93_bk_rc1.indd 35
35
4/14/2009 2:26:24 PM
Page 40
OOO O OO
dvp3350K_93_bk_rc1.indd 36
4/14/2009 2:26:24 PM
XOO O OO
XOO O OO
XOO O OO
XOO O OO
O: Indicates that this toxic or hazardous substance contained in all of the homogeneous
materials for this part is below the limit requirement in SJ/T11363 – 2006.
X: Indicates that this toxic or hazardous substance contained in at least one of the
homogeneous materials used for this part is above the limit requirement in SJ/T11363 - 2006.
36
Environmental Protection Use Period
This logo refers to the period ( 10 years ) during which the toxic or hazardous substances or elements
contained in electronic information products will not leak or mutate so that the use of these [substances or
elements] will not result in any severe environmental pollution, any bodily injury or damage to any assets.
Battery labeling logo
Environmental Protection Use Period
This logo refers to the period ( 5 years ) during which the toxic or hazardous substances or elements
contained in the battery will not leak or mutate so that the use of these [substances or elements] will not
result in any severe environmental pollution, any bodily injury or damage to any assets.
dvp3350K_93_bk_rc1.indd 36
4/14/2009 2:26:24 PM
Page 41
© 2009 Koninklijke Philips Electronics N.V.
dvp3350K_93_bk_rc1.indd 38
4/14/2009 2:26:24 PM
All right reserved
sgptt_0916/93-2_1
dvp3350K_93_bk_rc1.indd 38
4/14/2009 2:26:24 PM
Loading...