Signal-Noise (1kHz) > 90 dB
Dynamic range(1kHz)> 80 dB
Crosstalk (1kHz) > 70 dB
Distortion/noise (1kHz)> 65 dB
MPEG MP3 MPEG Audio L3
CONNECTIONS
Y Pb Pr OutputCinch 3x
Video Output Cinch (yellow)
Audio Output(L+R) Cinch (white/red)
Digital Output1 coaxial
IEC60958 for
CDDA / LPCM
IEC61937 for
MPEG 1/2,
Dolby Digital
AUDIO FORMAT
DigitalMPEG/ AC-3/compressed
PCMDigital
16, 20, 24 bits
fs, 44.1, 48, 96 kHz
MP3 (ISO 9660)96, 112, 128,
256 kbps &
variable bit rate
fs, 32, 44.1, 48 kHz
Analog Sound Stereo
Dolby Surround compatible downmix from Dolby
Digital multi-channel sound
CABINET
Dimensions (w x h x d) 360 x 37x 209 mm360 x 37x 209 mm
WeightApproximately
2kg2kgkg
POWER CONSUMPTION
Power Supply Rating110 V – 240 V;
50/60 Hz
Power consumption < 10 W
Power consumption in< 1 W
Standby mode
Specications are subject to change without prior
notice.
1-3
Safety instruction, Warning & Notes
Safety instruction
1. General safety
Safety regulations require that during a repair:
. Connect the unit to the mains via an isolation transformer.
. Replace safety components indicated by the symbol
only by components identical to the original ones. Any
other component substitution (other than original type)
may increase risk of fire or electrical shock hazard.
Safety regulations require that after a repair, you must
return the unit in its original condition. Pay, in particular,
attention to the following points:
. Route the wires/cables correctly, and fix them with the
mounted cable clamps.
. Check the insulation of the mains lead for external
damage.
. Check the electrical DC resistance between the mains
plug and the secondary side:
1) Unplug the mains cord, and connect a wire between
the two pins of the mains plug.
2) Set the mains switch the “on” position (keep the
mains cord unplug).
3) Measure the resistance value between the mains
plug and the front panel, controls, and chassis
bottom.
4) Repair or correct unit when the resistance
measurement is less than 1M
5) Verify this, before you return the unit to the
customer/user (ref. UL-standard no. 1492).
6) Switch the unit “off”, and remove the wire between
the two pins of the mains plug.
¡
.
2.Laser safety
This unit employs a laser. Only qualified service personnel
,
may remove the cover, or attempt to service this device
(due to possible eye injury).
Laser device unit
Type : Semiconductor laser GaAlAs
Wavelength : 650nm (DVD)
: 780nm (VCD/CD)
Output power : 7mW (DVD)
: 10mW (DVD /CD)
Beam divergence: 60 degree
Note: Use of controls or adjustments or performance of
procedure other than those specified herein, may result in
hazardous radiation exposure. Avoid direct exposure to
beam.
Warning
1-4
1.General
. All ICs and many other semiconductors are susceptible to
electrostatic discharges (ESD). Careless handing during
repair can reduce life drastically. Make sure that, during
repair, you are at the same potential as the mass of the
set by a wristband with resistance. Keep components and
tools at this same potential. Available ESD protection
equipment:
1) Complete kit ESD3 (small tablemat, wristband,
connection box, extension cable and earth cable)
4822 310 10671.
2) Wristband tester 4822 344 13999.
. Be careful during measurements in the live voltage
section. The primary side of the power supply , including
the heat sink, carries live mains voltage when you
connect the player to the mains (even when the player is
“off”!). It is possible to touch copper tracks and/or
components in this unshielded primary area, when you
service the player. Service personnel must take
precautions to prevent touching this area or components
in this area. A “lighting stroke” and a stripe-marked
printing on the printed wiring board, indicate the primary
side of the power supply.
. Never replace modules, or components, while the unit is
“on”.
2. Laser
. The use of optical instruments with this product, will
increase eye hazard.
. Only qualified service personnel may remove the cover
or attempt to service this device, due to possible eye
injury.
. Repair handing should take place as much as possible
with a disc loaded inside the player.
. Text below is placed inside the unit, on the laser cover
shield:
CAUTION: VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN, AVOID EXPOSURE
TO BEAM.
Notes: Manufactured under licence from Dolby
Laboratories. The double-D symbol is trademarks of Dolby
Laboratories, Inc. All rights reserved.
Notes
Lead-Free requirement for service
1-5
INDENTIFICATION:
Regardless of special logo (not always indicated)
One must treat all sets from 1.1.2005 onwards, according
next rules.
Important note
be treated in this way as long as you avoid mixing
solder-alloys (leaded/ lead-free). So best to always use
SAC305 and the higher temperatures belong to this.
Due to lead-free technology some rules have to be
respected by the workshop during a repair:
x Use only lead-free solder alloy Philips SAC305 with
order code 0622 149 00106. If lead-free solder-paste is
required, please contact the manufacturer of your
solder-equipment. In general use of solder-paste within
workshops should be avoided because paste is not easy
to store and to handle.
x Use only adequate solder tools applicable for lead-free
solder alloy. The solder tool must be able
o To reach at least a solder-temperature of 400°C,
o To stabilize the adjusted temperature at the
o To exchange solder-tips for different applications.
x Adjust your solder tool so that a temperature around
360°C
joint. Heating-time of the solder-joint should not exceed
~ 4 sec. Avoid temperatures above 400°C otherwise
wear-out of tips will rise drastically and flux-fluid will be
destroyed. To avoid wear-out of tips switch off un-used
equipment, or reduce heat.
x Mix of lead-free solder alloy / parts with leaded solder
alloy / parts is possible but PHILIPS recommends
strongly to avoid mixed
solder alloy types (leaded and lead-free). If one cannot
avoid, clean carefully the
solder-joint from old solder alloy and re-solder with new
solder alloy (SAC305).
: In fact also products a little older can also
solder-tip
– 380°C is reached and stabilized at the solder
x Use only original spare-parts listed in the
Service-Manuals. Not listed standard-material
(commodities) has to be purchased at external
companies.
xSpecial information for BGA-ICs:
- always use the 12nc-recognizable soldering
temperature profile of the specific BGA (for
de-soldering always use highest lead-free
temperature profile, in case of doubt)
- lead free BGA-ICs will be delivered in so-called
‘dry-packaging’ (sealed pack including a silica gel
pack) to protect the IC against moisture. After
opening, dependent of MSL-level seen on
indicator-label in the bag, the BGA-IC possibly
still has to be baked dry. This will be
communicated via AYS-website.
Do not re-use BGAs at all.
x For sets produced before 1.1.2005, containing
leaded soldering-tin and components, all needed
spare-parts will be available till the end of the
service-period. For repair of such sets nothing
changes.
x On our website:
www.atyourservice.ce.Philips.com
You find more information to:
BGA-de-/soldering (+ baking instructions)
Heating-profiles of BGAs and other ICs used in
Philips-sets
You will find this and more technical information
within the “magazine”, chapter “workshop news”.
For additional questions please contact your local
repair-helpdesk.
DVD Player Instruction
2-1
12675
a
STANDBY-ON
–Turns on this unit or turns off to normal
standby mode.
Disc tray
b
c
OPEN/CLOSE ç
–Opens/closes the disc tray.
d
Display panel
–Shows information about the current
status of the unit.
3
4
PLAY/PAUSE V
f
8
–Starts/pauses playback.
STOPÇ
g
–Stops playback.
h
(USB) jack
–Input for USB ash drive or digital
camera.
* Not all brands and models of digital
cameras are supported.
9
10
IR Sensor
e
–Point the remote control towards this
sensor.
i
MIC
–For microphone connection.
MIC LEVEL
j
–Microphone volume control.
Remote Control Instruction
2-2
:c\a^h]
a
2 (Standby-On)
– Turns on this unit or turns off to normal
standby mode.
1
ç (Open/Close)
b
– Opens/closes the disc tray.
2
DISPLAY
c
3
– Displays the current status or disc
information.
STWX
4
d
– ST: Cursor buttons for moving up/
down or press up/down for a slow
backward or forward search.
5
– WX: Cursor buttons for moving to the
left/right or press left/right for fast
backward or forward search.
6
SETUP
7
e
– Enters or exits the disc setup menu.
f
. (Previous/Next)
– Skips to the previous or next title/
chapter/track.
– Press and hold this button for fast
8
9
backward or forward search.
g
Ç(Stop)
– Stops playback.
AUDIO/CREATE MP3
h
– Selects an audio language or channel.
– Access create MP3 menu.
i VOCAL
– Choose audio channel or karaoke
method.
KARAOKE
– Toggles between ‘MIC’, ‘Vol’, ‘Echo’,
‘Key’ or ‘Karaoke Scoring’.
2-3
Remote Control Instruction
DISC MENU
j
– Enters or exits disc contents menu.
– For VCD 2.0 and SVCD, turns on or off
the playback control mode.
OK
k
– Conrms an entry or selection.
l
RETURN/TITLE
– Returns to the previous menu or shows
title menu
V(Play/Pause)
m
– Starts or pauses playback.
(USB)
n
– Switches to USB mode and shows the
content of the USB device.
( continued)
10
11
12
13
Numeric keypad 0-9
o
– Selects a track or title number of the
disc.
p
SUBTITLE
– Selects a DVD subtitle language.
q
ZOOM
– Zoom the picture on the TV.
14
15
16
17
3-1
Mechanical and Dismantling Instructions
Dismantling Instruction
The following guidelines show how to dismantle the player.
Step1: Remove 5 screws around the Top Cover, and then remove the Top Cover (Figure 1).
Step2: If it is necessary to dismantle Loader or Front Panel, the Front door should be removed first. (Figure 2)
Note: Make sure to operate gently otherwise the guider would be damaged.
Figure 1
Please kindly note that dismantle the front door
assembly carefully to avoid damage tray and the front door.
Figure 2
3-2
Mechanical and Dismantling Instructions
Dismantling Instruction
Step3: If the tray can’t open in normal way, you can make it through the instruction as below (Figure 3).
Note: Make sure to operate gently otherwise the guider would be damaged.
Push the guider until the tray out.
Make sure to operate gently to
avoid damage happening.
Step4: Dismantling Front Panel, disconnect the connectors (XP5, XP6, XP7), then release the snaps on the both sides of Front
Panel and bottom cabinet , then gently pull the Panel out from the set. (Figure 4 & 5)
Figure 3
XP6
XP7
XP5Snap 1
Figure 4
3-3
Mechanical and Dismantling Instructions
Dismantling Instruction
Snap 2
Step5: Dismantling Loader, disconnect the 3 connectors (XP2, XP3, XP4) aiming in the below figure, and remove 1 screw that
connects the loader and the bottom cabinet. (Figure 6)
Figure 5
XP2
XP4
XP3
Figure 6
3-4
Mechanical and Dismantling Instructions
Dismantling Instruction
Step6: Dismantling Main Board, first disconnect the connector (XP1), and then remove 4screws. (Figure 7)
XP1
Step7: Remove the 4 screws on Power Board to dismantle the Power Board. (Figure 8)
Figure 7
Figure 8
4-1
Software upgrade
Software upgrade
Preparation to upgrade software
1) Start the CD Burning software and create a new CD
project (Data Disc) with the following setting:
Label: DVP3XXX (No need the label name)
File Name: DVPXXXX_XX.BIN
Power on the set and open the tray, then press <5><5>
to check the File Name.
Note: It is required capital letter for the File System
name.
2) Burn the data onto a blank CDR
A. Procedure for software upgrade:
1) Power on the set and insert the prepared Upgrade
CDR.
2) The set will starts reading disc & response with the
following display TV screen:
Upgrade File DETECTED
Upgrade?
Press Play TO START.
3) Press <OK> button to confirm, then screen will display :
Files coping…
UPGRADING…
4) The upgraded tray will automatically open when files
coping complete, then take out the disc.
5) About 1 minute later, the trace will automatically close
when upgrading complete.
B. Read out the software versions to confirm upgrading
1) Power on the set and press <Setup> button on the
remote control.
2) Press <1><3><7><9> button.
The software version and other information are display
on the TV screen as follows:
Version XX.XX.XX.XX (Main version)
SUB-VER XX.XX.XX.XX (software version of
application software)
8032 XX.XX.XX.XX
Servo XX.XX.XX.XX (software version of
Servo)
RISC XX.XX.XX.XX
DSP XX.XX.XX.XX
Region Code X 4
Caution: The set must not be power off during
upgrading, Otherwise the Main board will be
damaged entirely.
Region Code Change
1) Power on the set and open the tray door;
2) Press the "Setup" button on the remote control, then
the setup interface should be displayed on the TV screen;
3) Move the right cursors of the remote control to choose the
"Reference" and press "1" "3" "8" "9" "3" "1" on the remote control;
4) Then move the up or down cursors to choose the region code.
Note: restart after above steps.
Loading...
+ 28 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.