Philips DVDR7250H/05, DVDR7250H/31, DVDR7250H/58, DVDR7260H/05, DVDR7260H/31 Service Manual

Published by KC-TE 0635 AV Systems Printed in the Netherlands Subject to modiﬁcation EN 3139 785 31801

DVDR7250H/05/31/58

HDD & DVD Recorder

Service Instruction

CLASS 1

LASER PRODUCT

Contents Page

1 Technical Speciﬁcations and Connection Facilities 2 2 Test Disc & Repair Hints 5 3 Firmware Upgrading & Diagnostic Software 6 4 Service Flow chart 7 5 Directions For Use 12

©

Copyright 2006 Philips Consumer Electronics B.V. Eindhoven, The Netherlands. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips.

Version 1.1

The 2006 range DVD Recorder products are repaired centrally. Defective sets must be identiﬁed, labelled and stored for pick-up. This document gives full instructions for a functional check. Technical information to repair faulty sets is therefore not provided in this document.

To test in-coming sets the following must be performed:

1. Verify / Reproduce the customer’s problem

2. Verify that set has latest Firmware (see chapter 3) and upgrade if it is not the latest version.

3. Full functional check

DVDR7260H/05/31/58

EN 2

3139 785 3180x

1.

Technical Speciﬁ cations and Connection Facilities

1. Technical Speciﬁ cations and Connection Facilities

1.1 Read / Write Speed

Type of Disc (Function) Disc Rotation Speed

Read Speed CD 7X CAV

Read Speed DVD 4X CAV

Write Speed DVD+R/RW 2.4X ZCAV

Write Speed DVD-R/RW 2X

1.2 General:

Mains voltage : 198V – 276V Mains frequency : 47Hz – 63Hz Power consumption (record) : <75W Standby Power Consumption : <4W Eco stand-by : <3W

1.3 RF Tuner (Analogue)

1.3.1.1 System:

PAL B/G, PAL D/K, SECAM L/L’, PAL I

1.3.1.2 RF – Loop Through:

Frequency range : 45MHz – 860MHz Gain: (ANT IN - ANT OUT) : -6dB to 0dB

1.3.1.3 Receiver:

PLL tuning with AFC for optimum reception Frequency range : 45.25MHz – 857MHz Sensitivity at 40dB S/N (video unweighted) : ≤ 60dBμV at 75Ω

1.3.1.5 Video Performance:

Channel 25 / 503,25 MHz, Test pattern: PAL BG PHILIPS standard test pattern, RF Level 74dBV Measured on SCART 1 Frequency response : 0.1MHz – 4MHz ± 3dB Group delay (0.1 MHz - 4.4 MHz) : 0 nsec ± 150 nsec

1.3.1.6 Audio Performance:

Audio Performance Analogue - HiFi:

Frequency response at SCART 1 (L+R) output : 100Hz – 12kHz / 0 ±

3dB S/N according to DIN 45405,7,1967 and PHILIPS standard test pattern video signal : ≥ 50dB Harmonic distortion (1 kHz, ± 25 kHz deviation) : ≤ 1.5%

Audio Performance NICAM: Frequency response at SCART 1 (L+R) output : 40Hz – 15kHz / 0 ±

3dB S/N according to DIN 45405,7,1967 and PHILIPS standard test pattern video signal : ≥ 60dB Harmonic distortion (1kHz) : ≤ 0.5%

1.3.1.7 RF Tuning

Automatic Search Tuning

Scanning time without antenna : 3min. typical Stop level (vision carrier) : ≥ 37dBμV Maximum tuning error (drift) during operation : ±100kHz

Tuning Principle:

Automatic B, G, I, DK and L/L’ detection. Manual selection in “STORE” mode

1.3.2 RF TUNER (Digital Terrestial)

1.3.2.1 DVB – T – Tuner

Frequency range : 448-861MHz Gain(Ant IN – Ant OUT) : -1dB to 3dB Auto Search scanning time (without Antenna input signal) : 40 sec typical

1.3.2.2 DVB – T – Video Performance

DVB-T-RF antenna signal IN :Video Performance measured at Rear Cinch Audio Out:

- S/N(Unweighted,5MHz-BW limitation SC trap ON): ≥ 55dB

- Frequency response 0.1 to 4.8MHz : +1/-3dB

- Y/Chroma delay : ≤ 55ns

- 2-T-K-factor : ≤ 2%

1.3.2.3 DVB-T-Audio Performance

DVB-T-RF antenna signal IN;Audio performance measured at Rear Cinch Audio Out:

- S/N(A-weighted, 22kHz-BW limited) : ≥ 88dB

- Frequency response 20Hz to 20kHz : ± 1dB

- THD + Noise (at 1kHz) : ≥ 85dB

- THD + noise (ratio) for 16Hz to 20kHz

- Channel Separation(at 1kHz) : ≥ 100dB

EN 3

3139 785 3180x

1.

Technical Speciﬁ cations and Connection Facilities

1.4 Analogue Inputs / Outputs

1.4.1 SCART 1(Connected to TV)

Pin Signals: 1 – Audio-out R 1.8V RMS 2 – Audio-out R 3 – Audio-out L 1.8V RMS 4 – Audio GND 5 – Blue / Chroma GND 6 – Audio- in L 7 – Blue-out 0.7Vpp ± 0.1V into 75 Ω 8 – Function switch < 2V = TV < 4.5V / < 7V = asp. Ratio 16:9 DVD > 9.5V / < 12V = asp. Ratio 4:3 DVD 9 – Green GND 10 – P50 control not use 11 – Green out 0.7Vpp ± 0.1V into 75Ω 12 – NC 13 – Red / Chroma GND 14 – Fast switch GND 15 – Red-out / Chroma-out 0.7Vpp ± 0.1V into 75Ω 16 – Fast switch RGB / CVBS or Y out < 0.4V into 75Ω = CVBS >1V / < 3V into 75Ω = RGB

17 – Y/CVBS GND OUT 18 – CVBS GND IN 19 – CVBS-out 1Vpp ± 0.1V into 75Ω 20 – CVBS-in 21 – Shield

1.4.2 SCART 2(Connected to AUX)

Pin Signals: 1 – Audio-out R 1.8V RMS 2 – Audio-in R 3 – Audio-out L 1.8V RMS 4 – Audio GND 5 – Blue / Chroma GND 6 – Audio-in L 7 – Blue-in 8 – Function switch 9 – Green GND 10 – NC 11 – Green-in 12 – NC 13 – Red / Chroma GND 14 – Fast switch GND 15 – Red-in / Chroma-in 16 – Fast switch RGB / CVBS or Y in 17 – CVBS GND 18 – Y/CVBS GND 19 – CVBS out sync 1Vpp ± 0.1V into 75Ω 20 – CVBS-in / Y-in 21 – Shield

1.4.3 Audio/Video Front Input Connectors

Audio - Cinch

Input voltage : 2.2Vrms Input impedance : > 10kΩ

Video - Cinch

Input voltage : 1Vpp ± 3dB Input impedance : 75Ω

Video - YC (Hosiden)

According to IEC 933-5 Superimposed DC-level on pin 4 (load > 100kΩ) < 2.4V is detected as 4:3 aspect ratio > 3.5V is detected as 16:9 aspect ratio Input voltage Y : 1Vpp ± 3dB Input impedance Y : 75Ω Input voltage C : burst 300 mVpp ± 3dB Input impedance C : 75Ω

1.4.4 Audio/Video Output rear Connectors

Audio - Cinch

Output voltage : 2.2Vrms max. Output impedance : > 10kΩ

Video - Cinch

Output voltage : 1Vpp ± 3dB Output impedance : 75Ω

Video - YC (Hosiden)

According to IEC 933-5 Superimposed DC-level on pin 4 (load > 100kΩ) < 2.4V is detected as 4:3 aspect ratio > 3.5V is detected as 16:9 aspect ratio Output voltage Y : 1Vpp ± 10/-15% Input impedance : 75Ω Output voltage C : 300 mVpp ± 1/-4dB Input impedance : 75Ω

1.5 Video Performance

All outputs loaded with 75Ω SNR measurements over full bandwidth without weighting.

1.6 Digital Inputs / Outputs

1.6.1 Digital Output

Digital Audio – Coaxial / Optical

LCM : according IEC 60958 MPEG 1, MPEG 2, AC3 : according IEC 61937 DTS : according IEC 61937 +

addendum

1.6.2 HDMI Output

Type A connector (19 pins)

1.6.3 Digital Video Input (IEEE 1394)

Implementation Standard according:

IEEE Std 1394-1995 IEC61883 - Part 1 IEC61883 - Part 2 SD-DVCR (02-01-1997)

Speciﬁ cation of consumer use digital VCR’s using 6.3mm

magnetic tape – dec.1994

Mechanical connection according to Annex of IEC 61883-1

EN 4

3139 785 3180x

1.

Technical Speciﬁ cations and Connection Facilities

1.6.4 G-Link (for IR-remote transmitting device)

Output voltage : 5 ± 0.5V (high level)

0.4 ± 0.3V (low level) Output impedance : 150Ω

1.6.5 SCART (RGB)

SNR : ≥ -65dB on all output Bandwidth : 4.8MHz ± 2dB

1.7 Audio Performance CD

1.7.1 Cinch Output Rear

Output voltage 2 channel mode : 2Vrms ± 2dB Channel unbalance (1kHz) : < 0.22dB Crosstalk 1kHz : > 100dB Crosstalk 16Hz-20kHz : > 87dB Frequency response 20Hz-20kHz : ± 0.5dB max Signal to noise ratio : > 85dB Dynamic range 1kHz : > 83dB Distortion and noise 1kHz : > 83dB Distortion and noise 16Hz-20kHz : > 75dB Intermodulation distortion : > 70dB Mute : > 95dB

1.7.2 Scart Audio

Output voltage 2 channel mode : 1.6Vrms ± 2dB Channel unbalance (1kHz) : < 1dB Crosstalk 1kHz : > 85dB Crosstalk 16Hz-20kHz : > 70dB Frequency response 20Hz-20kHz : ± 0.5dB max Signal to noise ratio : > 80dB Dynamic range 1kHz : > 75dB Distortion and noise 1kHz : > 75dB Distortion and noise 16Hz-20kHz : > 50dB Intermodulation distortion : > 70dB Mute : > 80dB

1.8 Digital Output

1.8.1 Coaxial

CDDA / LPCM (incl MPEG1) : according

IEC958,IEC60958-1,-3 MPEG2, AC3 audio : according IEC1937,

IEC61937 DTS : according IEC1937,

IEC 61937

amendment 1

1.9 Dimensions and Weight

Height of feet : 5.5mm Apparatus tray closed : WxDxH: 435 x 350 x

89mm Apparatus tray open : WxDxH: 435 x 487 x

89mm Weight without packaging : app.5.0kg ± 0.5kg Weight with packaging : app.8kg

1.10 Laser Output Power & Wavelength

1.10.1 DVD

Output power during reading : 0.8mW Output power during writing : 20mW Wavelength : 650nm

1.10.2 CD

Output power : 0.3mW Wavelength : 780nm

1.11 Playability

DVDR7250H DVDR7260H

Video Playback

1. Disc Media: CD-R/CD-RW, DVD+R DL, DVD+R/+RW, DVD-R/-RW, DVD-Video, Video CD/SVCD

xx

2. Compression Format: MPEG1, MPEG2

xx

Audio Playback

1. Disc Media: Audio CD, CD-R/RW

xx

2. Compression Format: Dolby Digital, MP3, MPEG2 Multi-channel, PCM

xx

Still Picture Playback

1. Disc Media: CD-R/RW

x

2. Picture Compression Format: JPEG

x

EN 5

3139 785 3180x

Test Disc & Repair Hints

2.

2.1 Test Disc

1) 7104 099 96611 CD-RW printed Audio Disc

2) 9965 000 25728 DVD Player Test Pack

3) - Blank DVD+RW

4) - Blank DVD-RW

2.2 Open the DVD Tray manually

Note: This procedure needs to be performed on condition that:

- a customer’s Disc is jammed in the DVD Tray

- the DVD Tray cannot be open via the normal open/close button on the set.

1) Place the set on the table with the bottom faced upwards as shown below.

2) Insert a screw driver into the slot and open the DVD Tray by sliding the screw driver in the direction shown.

Figure 2-1

2. Test Disc & Repair Hints

1

2

EN 6

3139 785 3180x

Firmware Upgrading & Diagnostic Software

3.

3. Firmware Upgrading & Diagnostic Software

3.1 Firmware Upgrading A. Preparation to upgrade ﬁ rmware:

1. Unzip the zip-archive ﬁ le

2. Start the CD Burning software and create a new CD project (data disc) with the following settings: File system : Joliet Format : MODE 2: CDROM XA Recording mode : SINGLE SESSION (TRACK-AT-ONCE), FINALIZED CD

Note: Long ﬁ le name is necessary for the preparation of the upgrade disc

3. Place the content of the zip-archive into the root directory of the new CD project.

4. Burn the data onto a blank CDR or CD-RW

B. Procedure to apply the ﬁ rmware upgrade:

1. Hold the <Record> + <Open/Close> buttons down and Power up the set.

2. The tray opens and set will display:

FORCE DL −>…. INSERT DISC

3. Insert the prepared Upgrade CDROM and close the tray.

4. The set will display:

INIT DSC −> ………. SYS VER −> READ FILES …. DOWNLOAD BE

The whole process takes less than 15 minutes Note: Do not press any buttons or interrupt the mains supply during the upgrading process, otherwise the set may becomes defective.

5. When the upgrade is completed the tray will open automatically and the set will display:

REMOVE DISC

6. Close the tray and the set will display:

DONE

7 The set will go into Standby mode.

C. How to read out the ﬁ rmware version to conﬁ rm set has been upgraded:

1. Power up the set.

2. Press <System> button on the Remote control and select {Setup} option

3. Press <Right> button to select {System}

4. The set will prompt you about clearing the Time Shift Buffer

5. Select {Yes} and press <OK> button

6. Press <Down> button several times to select {Version info}

7. Press <OK> button

8. The TV connected to the set will display:

(C) PHILIPS 2006 VERSION INFORMATION: DIF05_8/7028 AN SV11226 BE 43.3.7.9 ASP 1,18,1,10FP DTTM HW:01020102 DTTM SW:00040206 SIT7250H-FF5F-S28_F604 20060203-1650 pro sxcplusint EPG:3.06 DPMS:P_DPM

9. Press <System> button to exit

Philips DVDR7250H/05, DVDR7250H/31, DVDR7250H/58, DVDR7260H/05, DVDR7260H/31 Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual