Philips DVDR-3380, DVDR-3383 Service manual

Published by KC-TE 0617 AV Systems Printed in the Netherlands Subject to modification EN 3139 785 31811

DVDR3380 & DVDR3383

DVD Recorder

Service Instruction

CLASS 1

LASER PRODUCT

Contents Page

1 Technical Specifications and Connection Facilities 2
2 Test Disc & Repair Hints 5
3 Firmware Upgrading 6
4 Service Flow chart 8
5 Directions For Use 13

©

Copyright 2006 Philips Consumer Electronics B.V. Eindhoven, The Netherlands.
All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system or transmitted, in any form or by any means, electronic,
mechanical, photocopying, or otherwise without the prior permission of Philips.

Version 1.1

DVDR3380/05/31/51/58 & DVDR3383/51

The 2006 range DVD Recorder products are repaired centrally.
Defective sets must be identified, labelled and stored for pick-up.
This document gives full instructions for a functional check.
Technical information to repair faulty sets is therefore not provided in this document.

To test in-coming sets the following must be performed:

1. Verify / Reproduce the customer’s problem

2. Verify that set has latest Firmware (see chapter 3) and upgrade if it is not the latest version.

3. Full functional check

EN 2

3139 785 31810

1.

Technical Specifications and Connection Facilities

1. Technical Specifications and Connection Facilities

1.1 General:

Mains voltage : 220V – 240V
Mains frequency : 50 Hz
Power consumption (record) : 27 W
Standby Power Consumption : < 3 W

1.2 RF Tuner

Test equipment: Fluke 54200 TV Signal generator
Test streams: PAL BG Philips Standard test pattern

1.2.1 System

PAL B/G, PAL D/K, SECAM L/L’, PAL I

1.2.2 RF - Loop Through:

Frequency range : 43 MHz – 860 MHz
Gain: (ANT IN - ANT OUT)

w/o Amplifier : -4dB ± 2dB

Gain: (ANT IN - ANT OUT)

with Amplifier : 2dB ± 3dB

1.2.3 Receiver:

PLL tuning with AFC for optimum reception
Frequency range : 45.25 MHz – 857 MHz
Sensitivity at 40dB S/N
(video unweighted) : ≤ 40dBμV at 75 Ω

(high end)
≤ 60dBμV at 75 Ω
(low end)

1.2.4 Video Performance:

Channel 25 / 503,25 MHz,
Test pattern: PAL BG PHILIPS standard test pattern,
RF Level 74dBV, Measured on SCART 1
Frequency response : 0.1 MHz – 4 MHz ± 3dB
Group delay (0.1 MHz - 4.4 MHz) : 0 nsec ± 150 nsec

1.2.5 Audio Performance:

Audio Performance Analogue - HiFi:

Frequency response at SCART 1
(L+R) output : 100 Hz – 12 kHz / 0 ±

3dB
S/N Ratio (20Hz – 20kHz)
unweighted : ≥ 40dB
Harmonic distortion (1 kHz, ± 25
kHz deviation) : ≤ 1.5%

Audio Performance NICAM:
Frequency response at SCART 1
(L+R) output : 40 Hz – 15 kHz / 0 ±

3dB
S/N Ratio (20Hz – 20kHz)
unweighted : ≥ 65dB
Harmonic distortion (1kHz, ± 25
kHz deviation) : ≤ 0.5%

1.2.6 Tuning

Automatic Search Tuning

Scanning time without RF signal : 3min. typical
Stop level (vision carrier) : ≥ 37dB/μV
Maximum tuning error of a recalled
program : 62.5 kHz
Maximum tuning error (drift) during
operation : ± 100 kHz

Tuning Principle:

Automatic B, G, I, DK and L/L’ detection
Manual selection in “STORE” mode

1.3 Analog Inputs / Outputs

1.3.1 SCART 1 (Connected to TV)

Pin Signals:

1 Audio-out R 1.8V RMS
2 Audio-in R
3 Audio-out L 1.8V RMS
4 Audio GND
5 Blue / Chroma GND
6 Audio-in L
7 Blue-out 0.7Vpp ± 0.1V into 75Ω
8 Function switch < 2V = TV
> 4.5V / < 7V = asp. Ratio 16:9 DVD
> 9.5V / < 12V = asp. Ratio 4:3 DVD
9 Green GND
10 P50 control not use
11 Green out 0.7Vpp ± 0.1V into 75Ω
12 NC
13 Red / Chroma GND
14 Fast switch GND
15 Red-out / 0.7Vpp ± 0.1V into 75Ω
Chroma-out 300mVpp ± 3dB
16 Fast switch
RGB / CVBS
or Y out < 0.4V into 75Ω = CVBS
>1V / < 3V into 75Ω = RGB
17 Y/CVBS-out GND
18 CVBS-in GND
19 CVBS-out / Y-out 1Vpp ± 0.1V into 75Ω
20 CVBS-in
21 Shield

EN 3

3139 785 31810

1.

Technical Specifications and Connection Facilities

1.3.2 SCART 2 (Connected to AUX)

Pin Signals:

1 Audio-out R 1.8V RMS
2 Audio-in R
3 Audio-out L 1.8V RMS
4 Audio GND
5 Blue / Chroma GND
6 Audio-in L
7 Blue-in
8 Function switch
9 Green GND
10 P50 control
11 Green-in
12 NC
13 Red / Chroma GND
14 Fast switch GND
15 Red-in /
Chroma-in
16 Fast switch
RGB / CVBS or Y in
17 CVBS-out GND
18 Y / CVBS-in GND
19 CVBS-out 1Vpp ± 0.1V into 75Ω
20 CVBS-in / Y-in
21 Shield

1.3.3 Audio/Video Front Input Connectors

Audio - Cinch

Input voltage : 2.2Vrms
Input impedance : > 10kΩ

Video - Cinch

Input voltage : 1Vpp ± 3dB
Input impedance : 75Ω

Video - YC (Hosiden)

According to IEC 933-5
Superimposed DC-level on pin 4 (load > 100kΩ)
< 2.4V is detected as 4:3 aspect ratio
> 3.5V is detected as 16:9 aspect ratio
Input voltage Y : 1Vpp ± 3dB
Input impedance Y : 75Ω
Input voltage C : 300mVpp ± 3dB
Input impedance C : 75Ω

1.3.4 Out 1

Component Video Cinch Y/Pb/Pr

according EIO-770-I-A, EIA-770-2

Audio - Cinch
Output voltage : 2Vrms max.
Output impedance : > 10kΩ

1.3.5 Out 2

Audio - Cinch

Output voltage : 2Vrms max.
Output impedance : > 10kΩ

Video - Cinch

Output voltage : 1Vpp ± 3dB
Output impedance : 75Ω

Video - YC (Hosiden)

According to IEC 933-5
Superimposed DC-level on pin 4 (load > 100kΩ)
< 2.4V is detected as 4:3 aspect ratio
> 3.5V is detected as 16:9 aspect ratio
Output voltage Y : 1Vpp ± 3dB
Input impedance : 75Ω
Output voltage C : 300mVpp ± 3dB
Input impedance : 75Ω

1.4 Digital Inputs / Outputs

1.4.1 Digital Output

Digital Audio – Coaxial / Optical

LCM : according IEC 60958
MPEG 1, MPEG 2, AC3 : according IEC 61937
DTS : according IEC 61937 +

addendum

1.4.2 Digital Video Input (IEEE 1394)

Implementation Standard according:

IEEE Std 1394-1995
IEC61883 - Part1
IEC61883 - Part 2 SD-DVCR (02-01-1997)

Specification of consumer use digital VCR’s using 6.3mm

magnetic tape – dec.1994

Mechanical connection according to Annex of IEC 61883-1

1.5 Video Performance

All outputs loaded with 75Ω
SNR measurements over full bandwidth without weighting.

1.5.1 SCART (RGB)

SNR : ≥ 55dB on all output
Bandwidth : 4.8MHz -3dB

1.6 Audio Performance

1.6.1 Cinch Output Rear

Output voltage 2 channel mode : 2Vrms ± 1dB
Channel unbalance (1kHz) : < 0.22dB
Crosstalk 1kHz : > 110dB
Crosstalk 16Hz-20kHz : > 100dB
Frequency response 20Hz-20kHz : ± 0.2dB
Signal to noise ratio (unweighted) : < -95dB
Dynamic range 1kHz : < -90dB
Distortion and noise 1kHz : < 85dB
Distortion and noise 16Hz-20kHz : < 85dB
Intermodulation distortion : < -94dB
Mute : < -100dB

1.6.2 Scart Audio

Output voltage 2 channel mode : 1.6Vrms ± 2dB
Channel unbalance (1kHz) : < 1dB
Crosstalk 1kHz : > 85dB
Crosstalk 16Hz-20kHz : > 70dB
Frequency response 20Hz-20kHz : ± 0.5dB
Signal to noise ratio (unweighted) : > 80dB
Dynamic range 1kHz : > 75dB
Distortion and noise 1kHz : > 75dB
Distortion and noise 16Hz-20kHz : > 50dB
Intermodulation distortion : > 70dB
Mute : > 80dB

1.7 Dimensions and Weight

Height of feet : 5.5mm
Apparatus : WxDxH:435x322x43mm
Weight without packaging : 3kg
Weight with packaging : 4kg

EN 4

3139 785 31810

1.

Technical Specifications and Connection Facilities

1.8 Laser Output Power & Wavelength

1.8.1 DVD

Output power during reading : 0.8mW
Output power during writing : 20mW
Wavelength : 650nm

1.8.2 CD

Output power : 0.3mW
Wavelength : 780nm

1.9 Read / Write Speed

Type of Disc (Function) Disc Rotation Speed

Read Speed CD 7X CAV

Read Speed DVD 4X CAV

Write Speed DVD+R/+RW 2.4X ZCAV

Write Speed DVD-R/-RW

2X

1.10 Playability

DVDR3380

Video Playback

1. Disc Media:
CD-R/-RW, MP3­CD, VCD/SVCD,
DVD-Video,
DVD+R/+RW,
DVD-R/-RW,
DVD+RL DL

x

2. Compression
Format:
MPEG1, MPEG2
DivX 3.11, DivX

4.x, DivX 5.x, DivX

6.0

x

Audio Playback

1. Disc Media:
CD, CD-R/-RW,
MP3-CD

x

2. Compression
Format:
Dolby Digital, MP3,
MPEG2 Multi­channel, AAC,
WMA

x

3. MP3 bit rates: 32­256 kbps and VBR

x

Still Picture Playback

1. Disc Media:
Picture CD

x

2. Picture
Compression
Format:
JPG

x

EN 5

3139 785 31810

2.

Test Disc & Repair Hints

2. Test Disc & Repair Hints

2.1 Test Disc

1) 7104 099 96611 CD-RW printed Audio Disc

2) 9965 000 25728 DVD Player Test Pack

3) - Blank DVD+RW

4) - Blank DVD-RW

2.2 Open the DVD Tray manually

Note: This procedure needs to be performed on
condition that:

- a customer’s Disc is jammed in the DVD Tray

- the DVD Tray cannot be open via the normal
open/close button on the set.

1) Place the set on the table with the bottom faced upwards
as shown below.

2) Insert a screw driver into the slot and open the DVD Tray
by sliding the screw driver in the direction shown.

1

2

Figure 2-1

EN 6

3139 785 31810

3.

Firmware Upgrading

3. Firmware Upgrading

3.1 Firmware Upgrading

Important Instructions

• The Drive Upgrade and Loader Upgrade procedures has to be recorded into 2 separate disc.

A. Preparation to upgrade firmware:

1. Unzip the zip-archive file

2. Copy the files into different folder for burning into separate CD-R/CDRW.

3. Start the CD Burning software and create a new CD project (data disc) with the following settings:
File system : Joliet
Format : MODE 2: CDROM XA
Recording mode : SINGLE SESSION (TRACK-AT-ONCE), FINALIZED CD

Note: Long file name is necessary for the preparation of the upgrade disc

4. Place the file into the root directory of the new CD project.

5. Burn the data onto CDRs or CD-RWs

B. Procedure to apply the Drive upgrade:

1. Open the tray and load the Upgrade CDROM with Drive Upgrade file.

2. The tray closes and set will display:

“DRV UPG”

3. The OSD will display

“Loader Software Upgrade Disc detected.Select OK to start upgrading or CANCEL to exit.”

4. Click on the OK button.

5. The set will display:

“DRIVE UPGRADING”

With the OSD display

“Upgrading Software. Please Wait. Do not switch off the power.”

The whole process takes less than 5 minutes
Note: Do not press any buttons or interrupt the mains supply during the upgrading process, otherwise the set may becomes

defective.

6. When the upgrade is completed the tray will open automatically and the set will display:

“Loader Upgrade process has completed successfully .Press <OK> to reboot system.”

7. The tray open and the set will display:

“DRV OK”

8. Press <OK> and the set goes to standby .

EN 7

3139 785 31810

3.

Firmware Upgrading

B. Procedure to apply the software upgrade:

1. Open the tray and load the Upgrade CDROM with Software upgrade file.

2. The tray closes and set will display:

“Upgrading SW”

3. The OSD will display

“Software Upgrade Disc detected.Select OK to start upgrading or CANCEL to exit .”

4. Click on the OK button.

5. The set will display:

“Upgrading SW”

and the OSD will display

“Upgrading Software. Please Wait. Do not switch off the power.”

The whole process takes less than 5 minutes
Note: Do not press any buttons or interrupt the mains supply during the upgrading process, otherwise the set may becomes

defective.

6. When the upgrade is completed the tray will open automatically and the set will display:

“System is successfully upgraded.Remove disc from tray and reset system.”

7. The tray open and the set will display:

“SW DONE”

and the tray will open automatically for user to remove CD-ROM.

8. Press <OK> and the set goes to standby .

C. How to read out the firmware version to confirm set has been upgraded:

1. Power up the set.

2. Ensure no disc inside the loader,if no ,open the tray to remove the disc and close the tray.

3. Press <0> <0> <0> <9> in succession

4. Press <OK> button

5. The TV connected to the set will display:

“DVDR3380_EU_V03_07,Region:2, Drive 45.04.05.04
Build 0091 Mar 7 2006,12:17:31 Stroke:31 ”

EN 8

3139 785 31810

4.

Service Flow Chart

4. Service Flow Chart

4.1 Start Process

Start

A

(Verification

Test)

Is it a
Hardware
problem ?

Upgrade to latest

Firmware

Is it a known

complaint ?

Is Firmware

solution

available ?

Yes

No

Yes

No

Yes

No

Is the
complaint

solved ?

Return set to Customer with

Report on action done

Yes

No

Send refurbished set from pool

stock to Trade / customer

Is the

complaint

documented ?

Yes

No

Service W/S to contact the Trade /
Customer to work out a action plan.

Examples:

- explain them that the Firmware
solution is not ready

- Upgrade disc will be send
to them the moment solution
is ready

- etc.

- Attached a Defect Description Report
and Proof of Purchase.

- Pack defective set.

- Store defective set for pick-up.

EN 9

3139 785 31810

4.

Service Flow Chart

4.2 Verification Process

* If complaint is related to
System Menu setting

Connect up the Recorder

to TV antenna, TV set

and an External source

Check the Firmware

version on the set

Can the set

Start-up ?

Yes

No

A

(Verification

Test)

B

Recording

Check

C

Playback

Check

D *

System

Menu

Are the

checks result

ok ?

Yes

No

Return set to Customer with

Report on action done

Send refurbished set from pool

stock to Trade / customer

- Attached a Defect Description Report
and Proof of Purchase.

- Pack defective set.

- Store defective set for pick-up.

No

Yes

Is Firmware the

last released

version ?

Upgrade to latest

Firmware

EN 10

3139 785 31810

4.

Service Flow Chart

4.3 Recording Process

Test disc:

Blank DVD+RW

Does Timer

recording

functions ?

Yes

No

Does manual

recording

functions ?

Yes

No

B

Recording

Check

Make a Timer recording with:

1) Manually

2) VPS/PDC on and off

3) Show View System

4) external Cable Box/Satellite
Receiver
Playback the recorded disc to check

A

re Timer edit &
delete feature

working ?

Yes

No

Make a short manual recording from the
following source:

- Tuner

- CAM 1 (Front CVBS)

- DV

- Ext 1

- Ext 2

Playback the recorded disc to check

Does Disc

Editing

functions ?

1) Insert a recorded DVD+R/+RW disc

2) Press Top Menu button and check the
Disc editing features
Examples:

- Play

- Rename / Erase Disc

- Record New Title

- Overwrite / Lock Disc
Note: The displayed option in the disc
editing menu differ depending on the
situation & disc type

1) Play a recorded DVD+R/+RW disc

2) Press Disc Menu button and check Title
editing features
Examples:

- Play / Rename Title

- Edit Title (same as press Edit button
during play)

- Erase / Append Title

- Overwrite Title / Disc
Note: The displayed option in the disc editing
menu differ depending on the situation & disc
type

Does Title

Editing

functions ?

Continue

Continue

Yes

No

Yes

No

Send refurbished set from pool

stock to Trade / customer

- Attached a Defect Description Report
and Proof of Purchase.

- Pack defective set.

- Store defective set for pick-up.

EN 11

3139 785 31810

4.

Service Flow Chart

4.4 Playback Process

Test disc:

DVD Player Test Pack (12NC: 9965 000 25728)
CD-RW Printed Audio disc (12NC: 7104 099 96611)

Yes

No

C

Playback

Check

Playing the DVD video disc and check the
following:

- Pause & Search Fwd / Rev
functitons

- Next & Previous chapter

- Audio, Subtitle & Angle functions

- T/C options

Yes

No

Does the set

work ?

Does the set

work ?

Continue

Send refurbished set from pool

stock to Trade / customer

- Attached a Defect Description Report
and Proof of Purchase.

- Pack defective set.

- Store defective set for pick-up.

Playing other type of disc:

1) Use discs of DVD PLAYER TEST PACK for:

- (Super) Video CD

- MP3 disc

- Picture disc (slide show)

- special DVD playback check by layer change test using
DVD disc of this package

2) DivX 3.11, 4.x, 5.x, 6

3) For AUDIO CD use of CD-RW printed Audio Disc to check:

- Track 3 finger print

- Track 8: 600u black dot (max. after 1 min.)

EN 12

3139 785 31810

4.5 System Menu Process

4.

Service Flow Chart

D

System Menu Check

Does the

set work ?

Continue

Yes

No

System Menu - General and check the following
features:

- Screen Saver

- Country

- Video Output Format

- Restore Factory settings

System Menu - Clock and check the following
features:

- Date (dd/mm/yy)

- Time (hh:mm:ss)

- Date-Time Setting

- Show DivX Registration code

System Menu - Playback and check the
following features:

- TV Aspect Ratio

- Parental Rating Level

- Digital Audio Output

System Menu - Channel Setup and check the
following features:

- Channel Search

- Modify Channel Information

- Sort Channels

System Menu - Language and check the
following features:

- On Screen Display Language

- Default Disc Menu Language

- Default Subtitle Language

- Default Audio Language

System Menu - Record and check the following
features:

- Auto Chapter Marker

- Default Recording Source

- Default Recording Mode

Send refurbished set from pool

stock to Trade / customer

- Attached a Defect Description Report
and Proof of Purchase.

- Pack defective set.

- Store defective set for pick-up.

EN 13

3139 785 31810

5. Directions For Use

The following except of the Quick Use Guide serves as an introduction to the set.
The Complete Direction for the Use can be downloaded in different languages from the internet site of Philips Customer care Center:

www.p4c.philips.com

Quick Start Guide

DVD Player/ Recorder DVDR3380

Connect

Set up

Enjoy

1

2

3

What’s in the box?

DVD Player/ Recorder

RF Coaxial Cable

Remote Control

and 2 batteries

SC

ART Cable

User

Manual

1

Connect

2

Set up

Start with the ‘Basic Connection.’

If you have a VCR, follow the instructions for ‘Connection with a VCR or similar device’.

B

Initial Installation

A

Press

SYSTEM MENU

on the remote

control.

System Menu - General

Countr

y

German

y

Video Out

p

ut Format

Restore Factory Settin

gs

creen

S

ave

r

Note Use up

or down

keys to toggle through

the options. Select an item by pressing right

. To

con

rm a setting, press OK

.

B

Select the country of your residence.



Highlight and press

right

.

Select { Country } and press

right

to

access the options. Press

OK

to confirm

your selection.

C

Select the OSD language.



Highlight and press right

.

Select {

On-Screen Display Language

} and

press

right

to access the options. Press

OK

to confirm your selection.

D

Setup and install TV channels.



Highlight and press right

.

Select { Channel Search } and press

OK

on the remote control to start automatic TV

channel search.

E

Setting the date and time.



Highlight and press right

.

Select { Date (dd/mm/yy) } or { Time

(hh/mm/ss) } and press OK

.

Use the numeric keypad 0

-9

to

input the date/time, then press OK

to

con rm.

Note The settings will be updated according to the

broadcast channel information of preset Programme

Number 1.

F Press SYSTEM MENU

to exit.

Connection with a VCR or

similar device

A

Before Connecting

Your new Philips recorder replaces the VCR for your

recording needs. First, unplug all the connections

from your VCR.

B

Connecting

ANTENNA-IN

TV-OUT

~

MAINS

TO TV - I/

O

EXT

1

AUX - I/

O

EXT

2

SCART IN

Television (rear)

To antenna or

set-top box

Basic Connection

A

Before connecting, unplug the antenna cable that

is currently connected to your TV.

B

Connect the antenna cable to the ANTENNA-

IN

jack on the recorder.

C

Use the supplied RF coaxial cable to connect the

TV-OUT

jack on this recorder to the

Antenna In jack on the TV.

D

Use the SCART cable to connect the EXT1 TO

TV-I/O socket on this recorder to the

corresponding SCART input socket on the TV.

E

Connect the power cable from the recorder to

an AC power outlet.

Philips recorder

(rear)

To AC

power

ANTENNA-IN

TV-OUT

~

MAINS

TO TV - I/

O

EXT

1

AUX - I/

O

EXT

2

SCART IN

Television (rear)

Philips

recorder

(rear)

VCR or similar

device (rear)

A Follow the steps under ‘Basic Connections’

before you proceed to step

B below.

B

Use another SCART cable (not supplied) to

connect the EXT2 AUX-I/O SCART socket

on this recorder to the SCART OUT socket on

the VCR.

C Connect the power cable from your VCR to an

AC power outlet.

Note In this setup, the VCR cannot record TV

programmes.

For additional connection diagrams, see

the accompanying User Manual.

To

AC power

Philips recorder (front panel)

A

Finding the viewing channel

A

Press STANDBY-ON on the recorder.

B

Switch on the TV set.

Note If connected to your VCR, make sure it

is switched off or in standby mode before

proceeding.

C

In case you do not see the recorder’s blue

wallpaper, press “0” and the Channel Down

button on the TV’s remote control repeatedly

(or AV, SELECT,

° button) until you see this

screen. This is the correct viewing channel for

the recorder.

STANDBY-ON

To antenna or

set-top box

5.

Directions For Use

EN 14

3139 785 31810

5.

Directions For Use

2

Set up

B

Initial Installation

A

Press

SYSTEM MENU

on the remote

control.

System Menu - General

Countr

y

German

y

Video Out

p

ut Format

Restore Factory Settin

gs

creen

S

ave

r

Note Use up

or down

keys to toggle through

the options. Select an item by pressing right

. To

con

rm a setting, press OK

.

B

Select the country of your residence.



Highlight and press

right

.

Select { Country } and press

right

to

access the options. Press OK

to confirm

your selection.

C

Select the OSD language.



Highlight and press right

.

Select {

On-Screen Display Language

} and

press

right

to access the options. Press

OK

to confirm your selection.

D

Setup and install TV channels.



Highlight and press right

.

Select { Channel Search } and press

OK

on the remote control to start automatic TV

channel search.

E

Setting the date and time.



Highlight and press right

.

Select { Date (dd/mm/yy) } or { Time

(hh/mm/ss) } and press OK

.

Use the numeric keypad 0

-9

to

input the date/time, then press OK

to

con rm.

Note The settings will be updated according to the

broadcast channel information of preset Programme

Number 1.

F Press SYSTEM MENU

to exit.

Philips recorder (front panel)

A

Finding the viewing channel

A

Press STANDBY-ON on the recorder.

B

Switch on the TV set.

Note If connected to your VCR, make sure it

is switched off or in standby mode before

proceeding.

C

In case you do not see the recorder’s blue

wallpaper, press “0” and the Channel Down

button on the TV’s remote control repeatedly

(or AV, SELECT,

° button) until you see this

screen. This is the correct viewing channel for

the recorder.

STANDBY-ON

Quick Start Guide

2006 © Koninklijke Philips N.V.

All rights reser

ved.

12 NC 3139 245 21191

www.philips.com

Need help?

User Manual

See the user manual that came with your Philips recorder.

Online

Go to www.philips.com/support.

3

Enjoy

DVD Player/ Recorder DVDR3380

Connect

Set up

Enjoy

1

2

3

What’s in the box?

DVD Player/ Recorder

RF Coaxial Cable

Remote Control

and 2 batteries

SCART Cable

Start playback

A

Press OPEN/CLOSE

on the front of

the recorder

, load in a disc and close the disc

tray.

B Press

DISC MENU

and use up

or

down

keys to select a title.

C

Press

PLAY

to start playback.

D To stop playback, press

STOP

.

Start Recording

Recording from the TV or

an external device

A

Insert a recordable DVD disc in the

tray.

B

Press

REC SOURCE

repeatedly to select

the source to record from. (eg, TUNER, CAM1,

DV, EXT1 or EXT2).

�

To record a TV programme, use up

or

down

keys to scroll through the channels,

or press 0

-9

to select the channel that

you want to record.

Recording from the TV or an external

device (continued)

C

Press REC MODE

repeatedly to select the

recording mode.

E Press

REC

to start recording, press

REC

again to automatically record 30 minutes.

F To end recording, press

STOP

. ‘UPDATE’

will be displayed on the recorder.

G To playback the recording, press

DISC MENU

, select the title and press

PLAY

.

User

Manual

Hours of Recording that can be storedHours of Recording that can be stored

Types of discs for recording

Record Quality

124

6

High Quality HQ

Standard Play SP

Extended Play EP

Super Long Play SLP

4.7 GB DVD±R/±RW disc